Experiment 3: Vectors
In this lab, you will verify that the net force on an object in equilibrium is zero. Three scales,
calibrated in newtons, are hooked to a metal ring. They are put under tension to create forces on the
ring. Reading the scales gives the magnitudes of the forces; tracing the scales on a sheet of paper
records the directions. You then determine the resultant, using two different methods, to see if it
agrees with zero.
PROCEDURE: Hook the scales to the ring, and put
the chains on their other ends in the notches on the
metal circle. The forces should all be at least 5 N,
and should all be different from each other.
Slide a blank sheet of paper under the scales and
trace them to record their directions. Record the
magnitude of each force on the paper, estimating to
the nearest tenth of a newton. Each person in your
group should take their own data. However, there is no need to rearrange the apparatus for each
person.
Draw a line up the middle of each scale's outline, and put an arrowhead on the end. Label the forces
⃑ , ⃑ and ⃑ . Draw an x-axis along ⃑ and a y-axis perpendicular to it. Measure the angle of each
force, showing the results directly on the sheet.
ANALYSIS. (As with all labs, everyone in the group should do the following themselves.
However, this isn't a test; you should ask each other questions and correct each other's mistakes.)
Find the resultant two different ways:
1. Graphically. On another sheet of paper, find the resultant of your three forces by drawing them
to scale, head to tail, then drawing their resultant. Lined paper, such as notebook paper, is the most
convenient, although unlined paper will work. (Theoretically, the three forces should form a closed
triangle, but in practice, there is usually a small nonzero resultant because of experimental errors.)
A larger diagram is more accurate, so choose a scale which fills most of the page. The scale should
be written on the diagram. (For example, 1 cm = 20 N.) Don't bother finding an uncertainty with
this method. To save time, just assume it is + 1.5 N.
2. Component method. Calculate the components, and put them in the table provided. Use them to
find the components of the resultant. Include the uncertainty with each step. Some comments to
help with the uncertainties:
a. These particular scales give the magnitude of each force to about +.5 N, due to how closely
you can read the scale, and also their calibration. For the directions, assume the sine or cosine
of the angle might be off by 2% due to how accurately you drew the lines, and how closely you
can read the protractor. (This usually corresponds to about + 1°.)
b. The direction of ⃑ was not measured; we defined the x axis to lie along it. So, the
uncertainty of its x component is just the uncertainty of the scale, +.5 N. The y component is
not based on measurement at all, so its uncertainty is +0.
c. The components of the other two forces are calculated from two measurements, the scale and
the protractor. Since you multiply F times a function of the angle to get its components, the
components' uncertainty will be the sum of the percent uncertainties:
EXAMPLE: Find the uncertainty in the x component.
= -12.4 cos58 + (4% + 2%)
= -6.6 N + 6%
= -6.6 + .4 N
6% of 6.6 N is (.06)(6.6 N) = .4 N
d. Once you have the components of all three forces and their uncertainties, find the components
of the resultant. Find their uncertainties with the rule from lab 1A.
Conclusion: In your conclusion, say whether ⃑
uncertainty. That is,
+⃑
+⃑
- Does each component of the resultant agree with 0?
- Does the resultant from your scale drawing agree with 0?
=⃑
is true, within experimental
PHY 121
Experiment 3: Vectors
(attach sheet you slid under balances)
_____________________________________________________________________________
Graphical (head - to - tail) method:
(Attach solution, or do it on the back)
Answer: __________ N at __________ degrees.
_____________________________________________________________________________
Component method:
x-components
y-components
⃑
±
⃑
±
±
⃑⃑⃑
±
±
⃑ +⃑ +⃑
±
±
.5 N
0
±
0 N
Sample calculation: In the space below, show step-by-step how you calculated both components
and both uncertainties you show for ⃑ .