Evaluation Board for Audio Codec
EVAL-SSM2604
This data sheet describes how to configure and use the SSM2604
evaluation board. It is recommended that the SSM2604 evaluation
board data sheet be read in conjunction with the SSM2604
data sheet, which provides more detailed information about
the specifications, internal block diagrams, and application
guidance for the codec IC.
FEATURES
USB connectivity to host PC
External connectivity to DSP/MCU for digital audio signals
(available through general-purpose 2.54 mm pitch
connector)
2 audio jacks: stereo line input, stereo line output
Multiple test points (TP) across the board for monitoring
signals
Master/slave mode selectivity
EVALUATION BOARD DESCRIPTION
GENERAL DESCRIPTION
Figure 1 shows the top view of the PCB. Figure 2 shows the
bottom view of the board. The complete schematic of the board
is illustrated in Figure 23 to Figure 27. Figure 28 and Figure 29
show the top layer layout and the bottom layer layout, respectively, of the PCB. The bill of materials is shown in Table 1.
07777-030
07777-001
The SSM2604 is a low power, high quality stereo audio codec
for portable digital audio applications with one set of stereo
programmable gain amplifier (PGA) line inputs. The SSM2604
can operate as a master or slave and supports various clock
frequencies. The SSM2604 software-programmable stereo
output options provide many application possibilities because
the device can be used as a headphone driver or as a speaker
driver. Its volume control functions provide a large range of gain
control of the audio signal. Included in this data sheet is a detailed
setup and user guide for the SSM2604 evaluation board hardware and software. Read the Evaluation Board Quick Setup
section to ensure that proper communication is established
from the host PC to the SSM2604 evaluation board.
The SSM2604 evaluation board carries a complete application
circuit for the SSM2604. The board features a USB connection
to a host PC. This serves as the power supply, digital audio data,
and control/status data link, making it a plug-and-play USB
audio device that can communicate with the software under
the Microsoft® Windows® operating system. The board also has
a general-purpose 2.54 mm pitch connector to connect to an
external DSP/MCU for digital audio signals.
Figure 1. Top View of the SSM2604 Evaluation Board
Figure 2. Bottom View of the SSM2604 Evaluation Board
Evaluation boards are only intended for device evaluation and not for production purposes.
Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or
statutory including, but not limited to, any implied warranty of merchantability or fitness for a
particular purpose. No license is granted by implication or otherwise under any patents or other
intellectual property by application or use of evaluation boards. Information furnished by Analog
Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result
from its use. Analog Devices reserves the right to change devices or specifications at any time
without notice. Trademarks and registered trademarks are the property of their respective owners.
Evaluation boards are not authorized to be used in life support devices or systems.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
www.analog.com
Tel: 781.329.4700
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
Rev. 0
EVAL-SSM2604
TABLE OF CONTENTS
Features .............................................................................................. 1 Evaluation Board Quick Setup ....................................................5 General Description ......................................................................... 1 GUI Functional Blocks .................................................................6 Evaluation Board Description......................................................... 1 Evaluation Board Schematics and Artwork ...................................8 Revision History ............................................................................... 2 Ordering Information .................................................................... 12 Evaluation Board Hardware ............................................................ 3 Bill of Materials ........................................................................... 12 Hardware Description.................................................................. 3 Ordering Guide .......................................................................... 13 Evaluation Board Software .............................................................. 5 ESD Caution................................................................................ 13 REVISION HISTORY
12/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
EVAL-SSM2604
EVALUATION BOARD HARDWARE
HARDWARE DESCRIPTION
The SSM2604 evaluation board can be divided into several
segments: the microcontroller unit (MCU) with USB interface,
power supplies, analog input/output circuitry, the SSM2604
device, and the digital audio interface and bidirectional digital buffer.
•
MCU with USB Interface
The on-board microcontroller (MCU) with USB interface is
located on the top left portion of the evaluation board.
•
•
•
The MCU has two functions: transmitting the SSM2604
registers control word between the host PC and the
SSM2604 I2C port and transmitting digital audio data
between the host PC and the SSM2604 digital audio
interface.
Use SW1 to reset the MCU.
When the MCU is working correctly, LED D4 is blinking.
J8 is a mini Type B USB connector.
07777-003
•
user must remove Resistor R8 and apply the desired external voltage to the power supply pads, DCVDD and DGND,
on the top center of the board.
The output from LDO U2 provides the voltage for the
analog supply, AVDD. By default, the LDO output is set at
3.3 V. If a voltage other than 3.3 V is needed for AVDD the
user must remove Resistor R3 and apply the desired external voltage to the power supply pads, AVDD and AGND,
on the top center portion of the board.
Figure 4. Power Supply Circuitry
Analog Input/Output Circuitry
The right portion of the SSM2604 board includes analog input
and output circuitry for SSM2604. From top to bottom, these are:
Stereo line input jack
Stereo line output jack
07777-002
•
•
Figure 3. USB Interface Microcontroller
The power supplies are located on the top center portion of the
board. The entire board is powered through the USB connector.
There are two on-board low dropouts (LDOs) deriving 3.3 V
from the USB 5 V supply. LED D1 and LED D2 indicate power
supply status.
•
The output from LDO U3 provides the voltage for the
digital supply, DVDD. By default, the LDO output is set to
3.3 V. If a voltage other than 3.3 V is needed for DVDD, the
Rev. 0 | Page 3 of 16
07777-004
Power Supplies
Figure 5. Analog Input/Output Circuitry
EVAL-SSM2604
SSM2604 Device
The SSM2604 device is located in the center of the SSM2604 evaluation board.
signal (BCLK, DACLRC, DACDAT, ADCDAT, ADCLRC, MCLK,
and CLKOUT). These signals are routed to the corresponding
SSM2604 digital audio interface signals through the digital buffer.
07777-005
The buffer is bidirectional. Its direction is controlled in the software.
Figure 6. SSM2604 Device
On the bottom left of the evaluation board are the general-purpose
digital audio interface, J1, and the bidirectional digital buffer for
digital audio signals.
J1 is for connecting the SSM2604 digital audio interface signals
to/from the external DSP or MCU. One column of J1 is DGND
and the other column is marked with the name of the digital audio
Rev. 0 | Page 4 of 16
07777-006
Digital Audio Interface and Bidirectional Digital Buffer
Figure 7. General-Purpose Digital Audio Interface and Buffer
EVAL-SSM2604
EVALUATION BOARD SOFTWARE
EVALUATION BOARD QUICK SETUP
3.
Follow these five steps to quickly set up the evaluation board:
4.
07777-008
Make sure Jumper JP1 is applied.
Connect the board to the host PC with a mini Type B USB
cable. The first time the board is connected, the Windows
system reports that new hardware has been found. The PC
installs drivers for the new hardware automatically. SSM2604/
03/04 Eval Board appears on the status bar of the Speaker
control panel when installation is complete.
Figure 9. Error Message When USB Connection Is Not Established
5.
07777-007
When installation is complete, the software GUI appears.
Click the DAC button to play music files in media player.
You should be able to hear the music from the headphone or
from the active speaker connected to the headphone output
jack of the evaluation board. Note that only music files with a
48 kHz or 44.1 kHz sample rate are supported in this mode.
Figure 8. Speaker Control Panel Setting
USB TO
LINE OUT
LINE IN TO USB
LINE IN TO
LINE OUT
07777-009
1.
2.
Install the SSM2604 evaluation board control software from
SSM2604 Eval Board.msi.
From the Start menu, select Programs, then ADI, then
SSM2604 Eval Board, and then SSM2604.exe to run the
control software. If the USB cable is not connected or
Jumper JP1 is not applied before running the software, an
error message box appears. Close the software, check the
hardware connectivity, and rerun the software until the
message box no longer appears.
Figure 10. SSM2604 Control Software GUI
Rev. 0 | Page 5 of 16
EVAL-SSM2604
GUI FUNCTIONAL BLOCKS
The software GUI is logically split into menu items, command
buttons, and the register control panel. The menu is for setting
up the software and hardware working mode. The command
buttons are for register access. The register control panel is for
viewing and modifying each register.
07777-013
The SSM2604 supports the I2C standard for the register control
interface. This is selected under the Mode menu. For I2C mode,
you can select between two device addresses in the I2C mode
submenu.
Figure 14. Register Configuration File Format
07777-010
After setting the registers in the SSM2604 control software GUI
(see Figure 10), and clicking the Set button, the settings are
configured to the corresponding SSM2604 registers. If the Set
button is not clicked, the SSM2604 registers are not configured.
Figure 11. Control Interface Selection
There are two available digital audio interfaces for the SSM2604
on-board. One is the USB MCU. This is used to play back music
on the host PC and transmit to the SSM2604 DAC, or to record
music with the SSM2604 ADC and transmit to the host PC
through a USB connection. The other digital audio interface is
the general-purpose connector, J1. This is used to connect to
your DSP or MCU. Only one interface can communicate with
the SSM2604 at one time, and this is selected under the Control
menu (see Figure 12).
The I2C is a read and write protocol, so in I2C mode, when the
Get button is clicked, the SSM2604 registers are read back and
reflected in the SSM2604 GUI window.
The Reset button corresponds to SSM2604 Register R15. When it
is clicked, all SSM2604 registers are set to the power-on reset value.
There are three short-cut buttons: DAC, ADC, and Bypass.
These are used to quickly set the panel for the DAC path, the
ADC path, and the analog line-in to analog line-out loopback
path, respectively.
07777-011
The SSM2604 GUI window is logically split into several different
functional blocks. Each functional block represents the underlying
internal register of the SSM2604 that corresponds to the block.
Power Management Control
Figure 12. Digital Audio Interface Selection
This section controls SSM2604 Register R6. If an option is
checked, the power for that corresponding module is turned off;
otherwise, the power is turned on for that part. For example,
selecting POWER OFF shuts down the chip.
07777-012
07777-014
The Import and Export utilities, selected from the File menu,
are for reading/writing the SSM2604 registers in batch mode.
The file import utility reads the register setting from a .txt file
and then writes to the SSM2604 internal registers. The file
export utility reads the SSM2604 internal registers back and
then writes to a .txt file.
Figure 15. Power Management Control Section
Figure 13. File Import/Export Utility
The .txt file used for SSM2604 register configuration contains
multiple lines and each line is for one register. The first word
of a line is a 7-bit register address entry, which is in two-digit
hexadecimal format. The second word of a line is a 9-bit register
value entry, which is in three-digit hexadecimal format. When
using the import utility, use the export utility first to generate
the software .txt file as a template and then add, remove, or
modify the register entries in the template file.
Rev. 0 | Page 6 of 16
EVAL-SSM2604
Digital Audio Interface Control
This section controls SSM2604 Register R0 and Register R1 for
the left and right line input channel, respectively. Note that the
Right channel follows left option and the Left channel follows
right option are mutually exclusive.
This section controls SSM2604 Register R7 and D[2:1]
of Register R5. Specifically, the Active/Inactive option
corresponds to R9.
07777-015
Line Input Control
Figure 16. Line input Control section
This section controls SSM2604 Register R2 and Register R3 for
the left and right headphone output channel, respectively. Note
that the Right channel follows left option and Left channel
follows right option are mutually exclusive.
07777-018
Headphone Output Control
Figure 19. Digital Audio Interface Control Section
Sample Rate Control
07777-019
07777-016
This section controls SSM2604 Register R8.
Figure 17. Headphone Output Control Section
Figure 20. Sample Rate Control Section
Analog and Digital Audio Path Control
ALC Control
This section controls SSM2604 Register R16 and Register R17.
07777-020
07777-017
This section controls SSM2604 Register R4 and Register R5
for the analog and digital audio path, respectively. MIC Input
corresponds to D[8:6] and D[1:0] of R4. DAC & ADC corresponds to D[4:3] and D0 of R5 and D2 of R4. Audio Mixer
corresponds to D[5:3] of R4.
Figure 18. Analog and Digital Audio Path Control Section
Figure 21. ALC Control Section
Noise Gate Control
07777-021
This section controls SSM2604 Register R18.
Figure 22. Noise Gate Control Section
Rev. 0 | Page 7 of 16
EVAL-SSM2604
EVALUATION BOARD SCHEMATICS AND ARTWORK
U1
MCLK
USB_DACDAT
CLKOUT
DUT_BCLK
DACDAT
DUT_DACDAT
DACLRC
DUT_DACLRC
ADCDAT
DUT_ADCDAT
ADCLRC
DUT_ADCLRC
6
7
8
9
10
BCLK
LLINEIN
17
LLINEIN
16
RLINEIN
15
VMID
11
LOUT
12
ROUT
LLINEIN
analog_input
DACDATA
DACLRC
RLINEIN
RLINEIN
ADCDATA
ADCLRC
BCLK
USB_ADCDAT
TP1
DUT_CLKOUT
USB_LRCLK
VMID
1
Digital Buffer
USB_BCLK
5
DUT_MCLK
USB_MCLK
1
USB MCU
2
20
18
DUT_SDIN
19
DUT_SCLK
CLKOUT
C1
100nF
XTI_MCLK
LOUT
C2
10uF
LOUT
XTO
analog_output
NC
ROUT
ROUT
AGND
SDIN
SCLK
AVDD
13
14
DVDD
AVDD
C3
100nF
+
C4
10uF
AVDD
AVSS
AVDD
AGND
C5
100nF
+
AGND
C6
10uF
power
DVDD
DGND
3
DVDD
DVDD
DGND
07777-022
4
AGND
DVSS
DGND
ADI-SSM2604-QFN20
Figure 23. Schematic of SSM2604 Evaluation Board, SSM2604 Chip
AVDD
USB_VCC
D1
R1
U2
GND0
GND1
GND2
GND3
EN
IN
OUT
ADJ
R3
1
2
3
4
470R
LED GREEN
R4
3.16k
ADP1715
R2
0ohm
10K
R5
3
5
6
7
8
C7
C8
0.1uF
4.7uF
C9
C10
0.1uF
4.7uF
0ohm, NC
Q1
MMBT3904
1
R6
1k
AGND
2
DGND
AGND
DVDD
USB_VCC
D2
R7
U3
ADP1715
1
2
3
4
470R
LED GREEN
R9
10K
R8
3.16k
C11
C12
0.1uF
4.7uF
C13
C14
0.1uF
4.7uF
R10
1k
Q2
MMBT3904
1
07777-023
EN
IN
OUT
ADJ
3
GND0
GND1
GND2
GND3
2
5
6
7
8
AGND
Figure 24. Schematic of SSM2604 Evaluation Board, Power Supply
Rev. 0 | Page 8 of 16
EVAL-SSM2604
DVDD
U4
2
4
6
8
10
12
14
16
18
20
22
24
26
28
MCLK
CLKOUT
BCLK
DACLRC
DACDAT
ADCDAT
ADCLRC
2
4
6
8
10
12
14
16
18
20
22
24
26
28
1
24
48
25
ms_sel
GP_oe
USB_oe
BCLK
2
3
5
6
8
9
11
12
DACLRC
ADCLRC
13
14
16
17
19
20
22
23
USB_MCLK
HEADER2X14
USB_BCLK
USB_DACLRC
USB_DACDAT
DGND
1DIR
2DIR
1OE
2OE
USB_ADCLRC
1B0
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1A0
1A1
1A2
1A3
1A4
1A5
1A6
1A7
2B0
2B1
2B2
2B3
2B4
2B5
2B6
2B7
2A0
2A1
2A2
2A3
2A4
2A5
2A6
2A7
47
46
44
43
41
40
38
37
TP2
DGND
DUT_BCLK
1
1
3
5
7
9
11
13
15
17
19
21
23
25
27
4
10
15
21
28
34
39
45
GND_4
GND_10
GND_15
GND_21
GND_28
GND_34
GND_39
GND_45
TP3
DUT_DACLRC
1
J1
1
3
5
7
9
11
13
15
17
19
21
23
25
27
VCC1_7
VCC1_18
VCC2_31
VCC2_42
TP4
DUT_ADCLRC
1
7
18
31
42
36
35
33
32
30
29
27
26
74LVC16245A-DGG
7
18
31
42
4K7
DGND
GP_oe
MCLK
DVDD
DACDAT
C23
100nF
C24
10uF
C25
100nF
DGND
C26
100nF
13
14
16
17
19
20
22
23
DGND
USB_ADCDAT
CLKOUT
1
1
4
10
15
21
28
34
39
45
GND_4
GND_10
GND_15
GND_21
GND_28
GND_34
GND_39
GND_45
1DIR
2DIR
1OE
2OE
2
3
5
6
8
9
11
12
ADCDAT
DGND
VCC1_7
VCC1_18
VCC2_31
VCC2_42
1
24
48
25
DGND
DVDD
DGND
U5
C20
100nF
R11
C22
100nF
TP8
1B0
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1A0
1A1
1A2
1A3
1A4
1A5
1A6
1A7
2B0
2B1
2B2
2B3
2B4
2B5
2B6
2B7
2A0
2A1
2A2
2A3
2A4
2A5
2A6
2A7
47
46
44
43
41
40
38
37
TP9
DGND
36
35
33
32
30
29
27
26
DUT_MCLK
TP10
DUT_DACDAT
TP11
DUT_ADCDAT
07777-024
C19
100nF
1
C18
10uF
1
C17
100nF
1
C16
100nF
C21
10uF
TP7
DVDD
DVDD
C15
10uF
1
TP6
1
TP5
DVDD
DUT_CLKOUT
74LVC16245A-DGG
Figure 25. Schematic of SSM2604 Evaluation Board, Digital Buffer
LLINEIN
5K6
PHONOJACK
R37
10M, NC
C28
220pF
TP13
1uF
1
AGND
AGND
TP14
1
AGND
C30
R14
RLINEIN
5K6
10uF, NC
C32
R15
5K6
R38
10M, NC
C31
220pF
TP15
1uF
1
AGND
SPKVDD
TP31
1
L5 60z/1.5A
USB_VCC
C54
100nF
2
DGND
2
AGND
22nF
ROUT_S
R39
1
2
OUTR-
11
J5
2PAD
SSM2306
07777-025
R19
47K
1
14
13
GND#13
VDD#14
15
AGND
2
OUTR+
2
INR-
0R
100
10uF
C51
INR+
12
1
0R
8
1
OUTL-
SD
0R, NC
R42
J4
2PAD
1
R18
C52
U10
OUTL+
3
AGND
INL-
9
NC#6
J5
22nF
INL+
5
NC#7
R44
4
6
AGND
VDD#15
0R
7
R41
AGND
16
C50
0R
2
4
5
3
1
C34
22nF
PHONOJACK
AGND
TP17
R40
0R, NC
R17
47K
ROUT
C53
amp_sd
100
10uF
22nF
GND#16
R43
LOUT_S
NC#10
R16
10
C33
1
TP16
LOUT
1
J2
10uF, NC
C29
R13
5K6
2
4
5
3
1
1
TP12
C27
R12
AGND
Figure 26. Schematic of SSM2604 Evaluation Board, Analog Input and Output
Rev. 0 | Page 9 of 16
EVAL-SSM2604
DVDD
C35
PLLGND
100nF
C36
27pF
C37
27pF
DUT_SDIN
0R/NC R21
DUT_SCLK
R23
4K7
R22
4K7
7
1
6
TP19
JP1 1
1
6MHz
2
5
C38
1020B
1
B1
R34 R35
47K 47K
1
TP21
TP22
1
TP20
USB_DACLRC
35
USB_ADCLRC
34
DGND
DVDD
33
32
TP23
1
31
30
amp_sd
29
USB_oe
C42
100nF
28
R28
4.7K
TP24
P1_1
TP25
1
0R R31
TP26
0R R32
1
25
1
27
26
DUT_MODE
R29
4.7K
DUT_CSB
DUT_SCLK
DUT_SDIN
DGND
DVDD
A1
A1
TP27
B2
A2
PUSHBUTTON
A2
SW1
C46
1
1
C47
100nF 100nF
D3
LED GREEN
C48
C49
10uF
10uF
R36
330R
DGND
Figure 27. Schematic of SSM2604 Evaluation Board, USB MCU
07777-028
DGND
DGND
DVDD
TP28
B2
3
4
24LC64
1
38
37
CSCLK
CDATO
MCLKO1
MCLKO2
VREN
RESET
SDA
SCL
AVSS
R33
47K
36
ADM1818
100nF
VSS
U7
GND
C45
B1
SDA
2
07777-027
3
VCC REST
24
P3_0
DGND
P1_2
P1_0
RSTO
U9
2
39
40
41
42
44
43
45
47
46
P1_3
GP_oe
DVDD
XTALO
P1_4
EXTEN
60z/1.5A
DGND
XTALI
PLLFILI
TEST
23
12
DGND
DVSS#28
ms_sel
11
P1_5
MRESET
NC#22
10
DVDD#8
22
47pF
P1_6
DVDD#21
47pF
8
9
R30
47K
DM
21
C44
P1_7
NC#20
DVDD
C43
CSCHNE
DP
P3_5
7
PUR
20
6
19
5
P3_4
27R
18
27R
R26
DVDD#33
P3_3
R25
DVSS#4
DVSS#16
1K5
CRESET
17
1
2
3
4
5
6
R27
A2
USB_ADCDAT
CSYNC
MCLKI
16
4
L2
SCL
1
USB_DACDAT
CDATI
AVDD#2
P3_2/XINT
3
L4
USB-2PORT
48
2
15
PLLVDD
100nF
PLLFILO
P3_1
1
14
60z/1.5A
A1
USB_BCLK
RX
60z/1.5A
C39
100pF
TX
Vusb1
D-#2
D+#3
GND4
GND5
GND6
C41
DGND
USB_VCC
R24
3K0
PLLGND
L3
U8
10uF
A0
WP
DGND
13
60z/1.5A
C40
U6
VCC
USB_MCLK
1nF
L1
8
TP18
Y1
DVDD
0R/NC R20
Figure 28. Layout of SSM2604 Evaluation Board, Top Layer
Rev. 0 | Page 10 of 16
07777-029
EVAL-SSM2604
Figure 29. Layout of SSM2604 Evaluation Board, Bottom Layer
Rev. 0 | Page 11 of 16
EVAL-SSM2604
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Qty
2
13
Reference Designator
C29, C32
C2, C4, C6, C15, C18, C21, C24, C33, C34, C40,
C48, C49, C57
Description
1 μF capacitor, 3216
10 μF capacitor, 3216
Manufacturer
TDK
TDK
Part Number
C3216CH1H105J
C3216CH1H106J
4
23
C8, C10, C12, C14
C1, C3, C5, C7, C9, C11, C13, C16, C17, C19, C20,
C22, C23, C25, C26, C35, C41, C42, C45, C46,
C47, C54, C56,
C27, C30
C28, C31
C36, C37
C38
C39
C43, C44
C50, C51, C52, C53
D1, D2, D3, D4
J4, J6
JP1
J1
J2, J5
U8
L1, L2, L3, L4, L5
Q1, Q2
R1, R7
R2, R9
R3, R5
R4, R8
R6, R10
R11, R22, R23, R28, R29
R12, R13, R14, R15
R16, R18
R17, R19, R30, R33, R34, R35
R24
R25, R26
R27
R20, R21, R31, R32, R39, R40, R41, R42, R43
R36
R37, R38
SW1
TP1
TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10,
TP11, TP13, TP15, TP20, TP21, TP22
TP12, TP14, TP16, TP17, TP18, TP19, TP27, TP28
U1
U2, U3
U4, U5
4.7 μF capacitor, 3216
0.1 μF capacitor, 0603
TDK
TDK
C3216CH1H475J
C0603CH1E104J
10 μF capacitor, not populated, 3216
220 pF capacitor, 0603
27 pF capacitor, 0603
1 nF capacitor, 0603
100 pF capacitor, 0603
47 pF capacitor, 0603
22 nF capacitor, 0805
LED, 1206
Header 1 × 2
Header 1 × 2
Header 2 × 7
Audio jack
Mini USB, 1734035-1
Ferrite bead, 0805
SOT-23 transistor
470 Ω resistor, 0805
10 kΩ resistor, 0603
0 Ω resistor, 0805
3.16 kΩ resistor, 0603
1 kΩ resistor, 0603
4.7 kΩ resistor, 0603
5.6 kΩ resistor, 0603
100 Ω resistor, 0603
47 kΩ resistor, 0603
3.0 kΩ resistor, 0603
27 kΩ resistor, 0603
1.5 kΩ resistor, 0603
0 Ω resistor, 0603
330 Ω resistor, 0603
10 MΩ resistor, 0603, not populated
Pushbutton
Red test point, Header 1
Black test point, Header 1
TDK
TDK
TDK
TDK
TDK
TDK
TDK
Digi-Key
Digi-Key
Digi-Key
Digi-Key
Kycon
AMP/Tyco Electronics
Murata
Fairchild
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Royalohm
Panasonic
C3216CH1H106J
C0603CH1E221J
C0603CH1E270J
C0603CH1E102J
C0603CH1E101J
C0603CH1E470J
C0805CH1E223J
597-3311-407
A26508-02-ND
A26508-02-ND
A26508-07-ND
STX-3500-3
1734035-1
BLM21PG600SN1
MMBT3904
0805S4J0474T3E
0603S4J0103T3E
0805S4J0000T3E
0603S4J3161T3E
0603S4J0102T3E
0603S4J0472T3E
0603S4J0562T3E
0603S4J0101T3E
0603S4J0473T3E
0603S4J0303T3E
0603S4J0270T3E
0603S4J0153T3E
0603S4J0000T3E
0603S4J0331T3E
0603S4J0106T3E
EVQ-PHP03T
N/A
N/A
2
2
2
1
1
2
4
3
2
1
1
2
1
5
2
2
2
2
2
2
5
4
2
6
1
2
1
9
1
2
1
1
15
8
1
2
2
Green test point, Header 1
20-lead stereo audio codec
SOP8-26-195
SOP48-20-320
Rev. 0 | Page 12 of 16
Analog Devices
Analog Devices
NXP
N/A
SSM2604CPZ
ADP1715
74LVC16245A-DGG
EVAL-SSM2604
Qty
1
1
1
1
1
1
Reference Designator
U6
U7
U9
U8
U10
Y1
Description
SOP8-50-235
QFP48-20-355
SOT-23
Mini USB, 1734035-1
SSM2306
6 MHz OSC2-190-430175
ESD CAUTION
ORDERING GUIDE
Model
SSM2604-EVALZ1
1
Description
Evaluation Board
Z = RoHS Compliant Part.
Rev. 0 | Page 13 of 16
Manufacturer
Microchip
TI
Analog Devices
AMP/Tyco Electronics
MLF16-20-120A
ECS
Part Number
24LC64
TAS1020B
ADM1818
1734035-1
SSM2306
ECS-60-32-4X
EVAL-SSM2604
NOTES
Rev. 0 | Page 14 of 16
EVAL-SSM2604
NOTES
Rev. 0 | Page 15 of 16
EVAL-SSM2604
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
EB07777-0-12/08(0)
Rev. 0 | Page 16 of 16