IRM-S01SN OPTICAL SMOKE DETECTOR 1 Summary 1.2 Technical data

1.2 Technical data
APPENDIX ONE List of product
Emerson Network Power Co., Ltd. IRM-S01SN OPTICAL SMOKE DETECTOR
IRM-S01SN OPTICAL
SMOKE DETECTOR
1 Summary
Scope of application Early fire smog alarm
Smoke detector one piece;
operating voltage
DC 24V
product fitting one set;
Operating current
Static current
Detecting range
This is an optical smoke detector for alarm system. With
photoelectric signal processing technique, stable operation,
easy installation and flexible output mode for adapting various
alarm control panels. This product is widely used in houses,
hotels, schools and storages etc.
20M
Sensitivity
8mA;Alarm current 45mA
APPENDIX TWO
degree,
degree
Alarm mode
Network alarm signal
Output
NC/NO
Mounting method
Ceiling mounted
Dimension
Ö105
Toxic and hazardous substances or elements identified
Table
Hazardous Substances or Elements Identified Table
Polybrominated Polybrominated
Components Plumbum Mercury Cadmium Hexavalent
diphenyl ether
chromium biphenyls
54 mm
1.3 Environmental conditions
1.1 Product instruction
1.1.1 Appearance as Chart 1
Working temperature
10
Working humidity
95%RH
50
Finished
products
14
122
2 Installation
2.1 Notice
1.The product should not be installed in extreme hot or cold, or
high wind speed surroundings and in the conditions where
there is often a lot of smoker or dust.
2.To ensure its normal performance, please clean the detector
Chart 1
1.1.2 Definition of the wires order of Smoke Detector
as Chart 2
Terminal Number
Definition
24V+
Alarm Output1
Empty
surface with soft brush one time half a year. The detector
needs to be tested one time three months.
3.Please obey the correct methods to operate and maintain, once
service.
4.Optical smoke detector can increase the safety factor, but it can
not guarantee absolutely safety due to various factors,
besides correctly use this product, the user is advised to take
24VAlarm Output2
Empty
Chart 2
1.1.3 LED Light, Buzzer Indicator Information
LED flashes 5 times
LED flashes 1 time
LED on in normal
Delay 10 seconds
Test 1time
In the alarm status
: Content of this hazardous substance is under the required level of SJ/11363-2006 standard.
: Content of this hazardous substance is beyond the required level of SJ/11363-2006 standard.
Emerson Network Power Co., Ltd. has been committed to design and
manufacture of environmental products, we will continue to research
products to reduce and eliminate toxic substances. Limited by the current
technology level, it is hard to achieve a reliable substitute or find a mature
solution.
Explaining about the EPUP (Environmental Protection Use Period): EPUP
of this product(already identified on product), with normal use condition
and compliance with the safety note of this product,
The term from the date in produced to the deadline that toxic and hazardous
substances element of this product will not seriously impact the
environmental, personal and property.
Apply to IRM-S01SN somke detector
the detector is found to defective, please exchange and
all necessary precautions for safety and enhance safety
Empty
User manual one piece.
2
2.2 Mechanically installation
1.Chose a suitable position (normally mounted in the center of the
detecting area on the ceiling)
2.Input the wire and connect to the net wire terminal correctly.
3.Connection definition: connect with net wire directly. Refer to
Chart 2.
Emerson Network Power Co., Ltd.
Add: No. 1 Kefa Road, Science & industry Park, Nanshan District
P.C.: 518057
Website: www.emersonnetworkpower.com.cn
Service hot line: 4008876510
E-mail: service@emersonnetwork.com.cn
Data edition: V1.0
Filed Date: 2010-7-9
Copyright all rights reserved. If content change without notice.