GAFMC EVERGUARD® GUIDE SPECIFICATION PART 1 GENERAL 1.01 SUMMARY A. Section Includes 1. Thermoplastic Single-Ply Roofing 2. Insulation B. Related Sections 1. Section 06100: Rough Carpentry 2. Section 07620: Sheet Metal Flashing and Trim 3. Section 15430: Plumbing Specialties 1.02 REFERENCES A. Factory Mutual (FM Global) - Approval Guide B. Underwriters Laboratories (UL) - Roofing Systems and Materials Guide (TGFU R1306) C. American Society for Testing and Materials (ASTM) - Annual Book of ASTM Standards D. Sheet Metal and Air Conditioning Contractors National Association, Inc. (SMACNA) Architectural Sheet Metal Manual E. National Roofing Contractors Association (NRCA) F. American Society of Civil Engineers (ASCE) 1.03 DEFINITIONS A. Roofing Terminology: Refer to ASTM D1079 and the glossary of the National Roofing Contractors Association (NRCA) Roofing and Waterproofing Manual for definitions of roofing terms related to this section. 1.04 PERFORMANCE REQUIREMENTS A. Provide an installed roofing membrane and base flashing system that does not permit the passage of water, and will withstand the design pressures calculated in accordance with the most current revision of ASCE 7. B. GAFMC shall provide all primary roofing materials that are physically and chemically compatible when installed in accordance with manufacturers current application requirements. 1.05 SUBMITTALS A. Product Data: Provide product data sheets for each type of product indicated in this section. 07540-1 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION B. Shop Drawings: Provide manufacturers standard details and approved shop drawings for the roof system specified. C. Samples: Provide samples of insulations, fasteners, membrane materials and accessories for verification of quality. D. Certificates: Installer shall provide written documentation from the manufacturer of their authorization to install the roof system, and eligibility to obtain the warranty specified in this section. 1.06 QUALITY ASSURANCE A. Manufacturer’s Qualifications: GAFMC shall provide a roofing system that meets or exceeds all criteria listed in this section. B. Installer’s Qualifications: 1. Installer shall be classified as a Master Select contractor as defined and certified by GAFMC. 2. Installer shall be classified as a Master contractor as defined and certified by GAFMC. 3. Installer shall be classified as an Authorized contractor as defined and certified by GAFMC. C. Source Limitations: All components listed in this section shall be provided by a single manufacturer or approved by the primary roofing manufacturer. D. Final Inspection 1. Manufacturers representative shall provide a comprehensive final inspection after completion of the roof system. All application errors must be addressed and final punch list completed. 1.07 PRE-INSTALLATION CONFERENCE A. Prior to scheduled commencement of the roofing installation and associated work, conduct a meeting at the project site with the installer, architect, owner, GAFMC representative and any other persons directly involved with the performance of the work. The installer shall record conference discussions to include decisions and agreements reached (or disagreements), and furnish copies of recorded discussions to each attending party. The main purpose of this meeting is to review foreseeable methods and procedures related to roofing work. 1.08 REGULATORY REQUIREMENTS A. All work shall be performed in a safe, professional manner, conforming to all federal, state and local codes. B. Exterior Fire Test Exposure: Provide a roofing system that will achieve an Underwriters Laboratories rating for roof slopes indicated.UL Class A 2. UL Class B 3. UL Class C 07540-2 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 4. Roof Slope:_______________ C. Windstorm Classification: Provide a roofing system which will achieve a Factory Mutual wind uplift rating, as listed in the current FM Approval Guide. 1. FM 1-60 2. FM 1-75 3. FM 1-90 1.09 DELIVERY, STORAGE AND HANDLING A. Deliver all roofing materials to the site in original containers, with factory seals intact. All products are to carry either a GAFMC or BMCA® label. B. Store all pail goods in their original undamaged containers in a clean, dry location within their specified temperature range. C. Do not expose materials to moisture in any form before, during, or after delivery to the site. Reject delivery of materials that show evidence of contact with moisture. D. Remove manufacturer supplied plastic covers from materials provided with such. Use “breathable” type covers such as canvas tarpaulins to allow venting and protection from weather and moisture. Cover and protect materials at the end of each work day. Do not remove any protective tarpaulins until immediately before the material will be installed. E. Materials shall be stored above 55°F (12.6°C) a minimum of 24 hours prior to application. 1.10 PROJECT CONDITIONS A. Weather 1. Proceed with roofing only when existing and forecasted weather conditions permit. 2. Ambient temperatures must be above 45°F (7.2°C) when applying hot asphalt or water based adhesives. 1.11 WARRANTY A. Provide Manufacturers standard Diamond Pledge Guarantee with single source coverage and no monetary limitation where the manufacturer agrees to repair or replace components in the roofing system, which cause a leak due to a failure in materials or workmanship. 1. Duration: Five(5), Ten (10), Fifteen (15), Twenty (20) years from the date of completion. B. Provide Manufacturers standard System Pledge Guarantee with single source coverage and a monetary limitation of one (1) dollar per square foot where the manufacturer agrees to repair or replace components in the roof system, which cause a leak due to failure in materials or workmanship. 1. Duration: Five (5), Ten (10), Fifteen (15), Twenty (20) years from the date of completion. C. Provide Manufacturers standard Labor and Material Guarantee where the manufacturer agrees to repair or replace the portion of the roofing materials, which have resulted in a leak due to a manufacturing defect or defects caused by ordinary wear and tear. 07540-3 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 1. Duration: Five(5), Ten (10), Fifteen (15), Twenty (20) years from the date of completion. PART 2 PRODUCTS 2.01 ACCEPTABLE MANUFACTURER A. GAF Materials Corporation - 1361 Alps Road, Wayne, NJ 07470 2.02 ROOF BOARD A. Underlayment or overlayment board with a water-resistant and silicone treated gypsum core with glass fiber facers embedded on both sides, and pre-primed on one side. GP DensDeck Prime Roof Board, distributed by BMCA®. 1. Board Thickness: 2. Thermal Resistance (R value) of: B. Underlayment or overlayment board with a water-resistant and silicone treated gypsum core with glass fiber facers embedded on both sides. GP Dens-Deck Roof Board, distributed by BMCA® 1. Board Thickness: 2. Thermal Resistance (R value) of: 2.03 INSULATION ACCESSORIES A. Tapered Edge Strip: Factory fabricated rigid perlite strip cut at angles to provide a smooth transition between differences in elevation. EnergyGuard Tapered Edge Strip, by BMCA® 2.04 SEPARATION SHEETS A. Fire resistant glass fiber mat used as a separation sheet over polystyrene foam insulation or beneath insulation over wood substrates. Each roll contains ten (10) squares (1,000 sq. ft.) of material, 4’ x 250’ (1.2m x 76.9m), 80 lbs. (36.4 kg), Fiberglass Fire Sheet 10. B. Fire resistant glass fiber mat used as a separation sheet over polystyrene foam insulation or beneath insulation over wood substrates. Each roll contains four (4) squares (420 sq. ft.) of material, 4’ x 105’ (1.2m x 32.3m), 79 lbs. (35.9 kg), Fiberglass Fire Sheet 50. C. Non-woven polyester UV-stabilized mat, 3 oz./sq. yd. used as a separation sheet beneath membranes as a protection layer and used over membranes in ballast applied assemblies. Each roll contains thirty (30) squares (3,000 sq. ft.) of material, 10’ x 300’ (3.07m x 92.3m), 75 lbs. (34.1 kg), Poly Separation Layer 3 oz. D. Non-woven polyester UV-stabilized mat, 6 oz./sq. yd. used as a separation sheet beneath membranes as a protection layer and used over membranes in ballast or paver applied assemblies. Each roll contains thirty (30) squares (3,000 sq. ft.) of material, 10’ x 300’ (3.07m x 92.3m), 125 lbs. (56.8 kg), Poly Cushioning Layer 6 oz. 07540-4 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 2.05 MEMBRANE MATERIALS A. A fleece-backed, polyester scrim reinforced PVC membrane with a nominal 0.080 inch (80 mils) thickness, for use as a single ply roofing membrane. Meets or exceeds the minimum requirements of ASTM D-4434. Each full roll contains approximately 380 sq.ft. of roofing material, 76”X60’, weighing 225 lbs. EverGuard® EGFB-80 PVC roofing membrane by GAFMC. 1. Color: White Gray Tan 2.06 BALLAST A. Stone ballast shall be smooth, water worn gravel with rounded edges and corners, relatively free of sand, loam, and other foreign substances, and contain less than 4% fines. 2.07 PAVERS A. Extruded polystyrene insulation panels with an integral latex-molded mortar top face. Nominal 2” thick insulated pavers to be provided with tongue and groove interlocking edges. 2.08 FLASHING MATERIALS A. A fleece-backed, polyester scrim reinforced PVC membrane with a nominal 0.080 inch (80 mils) thickness, for use as a single ply roofing membrane. Meets or exceeds the minimum requirements of ASTM D-4434. Each full roll contains approximately 380 sq.ft. of roofing material, 76”X60’, weighing 225 lbs. EverGuard® EGFB-80 PVC roofing membrane by GAFMC. B. A smooth type, polyester scrim reinforced PVC membrane with a nominal 0.080 inch (80 mils) thickness, for use as a flashing membrane. Meets or exceeds the minimum requirements of ASTM D-4434. Each full roll contains approximately 450 sq.ft. of roofing material, 72” X 75’, weighing 243 lbs. EverGuard® SR-80 single-ply roofing membrane by GAFMC. C. A smooth type, unreinforced thermoplastic PVC membrane for use as an alternative flashing/reinforcing material for penetrations and corners. 0.055 inches (55 mils) nominal thickness, EverGuard PVC UN-55 Detail Flashing Membrane, by GAFMC. D. An 8 inch (20 cm) wide smooth type, polyester scrim reinforced PVC membrane strip for use as a cover strip over coated metal and stripping-in coated metal flanges and general repairs: 0.040 inches (40 mils) nominal thickness, EverGuard SR 40 Reinforced Flashing Strips, by GAFMC. E. 25 gauge steel with 0.023” thick PVC based film. Factory supplied in sheets and required for fabrication into metal gravel stop and drip edge profiles, metal base and curb flashings, sealant pans, and scupper sleeves. Sheet size 4’ x 10’, sheet weight 47 lbs., EverGuard® PVC Coated Metal, by GAFMC. 2.09 ADHESIVES, SEALANTS and PRIMERS 07540-5 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION A. Solvent-based Bonding Adhesive: Solvent based rubberized adhesive for use with EverGuard PVC membranes, EverGuard Bonding Adhesive, by GAFMC. B. Water-based Bonding Adhesive: Water based rubberized adhesive for use with EverGuard PVC membranes, EverGuard H2O Bonding Adhesive, by GAFMC. C. One part polyurethane sealant suitable for sealing the upper lip of exposed termination bars and penetrations, and around clamping rings. Meets or exceeds ASTM C-920-87, Type S, Grade NS, Class 25, EverGuard Caulking, by GAFMC. D. One part butyl based high viscosity sealant suitable for sealing between flashing membrane and substrate surface behind exposed termination bars and for sealing between roofing membrane and drain flange. EverGuard Water Block, by GAFMC. E. 100% solids epoxy based two-part sealant suitable for filling sealant pans at irregularlyshaped penetrations. Epoxy is part A. Polyamide is part B. EverGuard 2-Part Pourable Sealant, by GAFMC. F. Asphalt primer: ASTM D 41 Matrix 307 Standard Asphalt Primer, by BMCA®. G. Insulation Adhesive: Matrix 157 Monster Grip, by BMCA®. H. Insulation Adhesive: Oly-Bond 500 distributed by BMCA®. I. Insulation Adhesive: Insta-Stik by Dow Chemical *It is the responsibility of those involved with the design of the building to obtain indemnification for the attachment and integrity of the Insta-Stik Product. GAFMC assumes no responsibility for the Insta-Stik product or its performance within the system. 2.10 ACCESSORIES * A. Mechanical fasteners for securing of insulation, roofing and flashing materials as specified. Required fastener type determined by type of substrate and requisite attachment. Drill•Tec fasteners, by BMCA. 1. Drill•Tec Standard Roofing Fastener 2. Drill•Tec ASAP 3P Fastener 3. Drill•Tec ASAP 3S Fastener 4. Drill•Tec Heavy Duty Roofing Fastener 5. Drill•Tec NTB-1HWO Fastener 6. Drill•Tec NTB-1HWW Fastener 7. Drill•Tec CD-10 Fastener 8. Drill•Tec Fluted Nail, Concrete Fastener 9. Drill•Tec Lite-Deck Fastener 10. Drill•Tec CR Base Sheet Fastener 11. Drill•Tec CR 1.2 Base Sheet Fastener 12. Drill•Tec Masonry Anchor 13. Drill•Tec 2" Galvalume Plate 14. Drill•Tec 3" Galvalume Plate 15. Drill•Tec 2” NTB Plate 07540-6 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 16. Drill•Tec 17. Drill•Tec 18. Drill•Tec 19. Drill•Tec 3” NTB Plate Lite-Deck Plate Base Sheet Plate Locking Impact Nail B. Extruded aluminum termination bar with angled lip caulk receiver and lower leg bulb stiffener. Pre-punched slotted holes at 6” on center or 8” on center. ¾” x 10’ with 0.090” cross section, EverGuard® Lip Termination Bar, by GAFMC. C. 0.075” thick molded PVC membrane sized to accommodate most common pipe and conduits, (1” to 6” diameter pipes), including square tube. Hot-air welded directly to EverGuard PVC membrane, supplied with stainless steel clamping rings, EverGuard® PVC Preformed Vent Boots by GAFMC. D. 0.075” thick molded PVC membrane designed to accommodate both inside and outside corners of base and curb flashing. Hot-air welds directly to EverGuard PVC membrane. Size 4” x 4” with 4” flange, EverGuard® PVC Preformed Corners by GAFMC. E. Factory fabricated assemblies used to accommodate three-dimensional joints in a roof structure. Two standard sizes to accommodate most common joint widths. Standard 50 foot continuous length minimizes joints, universal style suitable for both field and wall expansion joint in both flat-mounted and curb-mounted styles. Made of 0.060” thick reinforced membrane with foam supported bellows, heat welds directly to roofing membrane. Equipped with metal nailing flanges and membrane welding flaps, Metalastic® Prefabricated Expansion Joint Covers by GAFMC. F. /8” thick extruded and embossed PVC pads 30” x 36”, heat welds directly to roofing membrane. Unique herringbone traction surface, safety yellow or gray in color, EverGuard® PVC Walkway Pads, by GAFMC G. 1/8” thick extruded and embossed PVC roll 30” x 50’, heat welds directly to roofing membrane. Unique herringbone traction surface, safety yellow or gray in color, EverGuard® PVC Walkway Rolls, GAFMC. PART 3 EXECUTION 3.01 EXAMINATION A. Verify that the surfaces and site conditions are ready to receive work. B. Verify that the deck is supported and secured. C. Verify that the deck is clean and smooth, free of depressions, waves, or projections, and properly sloped to drains, valleys, eaves, scuppers or gutters. D. Verify that the deck surfaces are dry and free of ice or snow. E. Verify that all roof openings or penetrations through the roof are solidly set, and that all flashings are tapered. 07540-7 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 3.02 SUBSTRATE PREPARATION A. Recover 1. Suitable roofs for recover shall be free of dust, dirt, debris, and any contaminants that may adversely affect the performance of the new roof. Areas of substantial deck deflection or membrane imperfections shall be corrected prior to installing any new roofing. 2. For recover installations over single-ply, fluid applied, coal tar and metal roofs, contact GAFMC Contractor Services for prior approval and technical requirements. 3. Taking test cuts to verify the existing roof construction and condition. Three test cuts should be made for roofs under 100 squares and one test cut per 100 squares above the minimum amount. It is highly recommended and in certain circumstances, required, that a moisture survey be made to determine the extent of wet insulation and moisture entrapment. Contact GAFMC Contractor Services for more information on moisture surveys. 4. Existing substrates and insulation (if applicable) must be dry over the majority of the roof area. Wet or deteriorated areas of insulation and substrate must be removed and replaced with new materials. When adhering insulation or new roofing directly to the existing roof surface, the existing roof system components must be well attached to each other and their substrate. 5. All applicable code requirements must be met for recover over an existing roofing system. 6. GAFMC does not recommend partial recover or re-roofing of a single roof area due to the potential for defects in the portion of the roof system not replaced or negatively affecting the performance of the new membrane. When required by project conditions or budget considerations, GAFMC requires full separation of the old and new roof areas by means of a full curb mounted expansion joint or area divider installed to provide a complete watertight seal or break between areas. Tie-in constructions, in which the old and new membranes are adhered directly to each other and stripped in are not acceptable for coverage under certain guarantees. 3.03 INSTALLATION - GENERAL A. Install GAFMC’s EverGuard® PVC roofing system according to all current application requirements in addition to those listed in this section. B. GAFMC EverGuard® PVC Specification #: P-BA-R-N-80FB C. Start the application of membrane plies at the low point of the roof or at the drains, so that the flow of water is over or parallel to, but never against the laps. 3.04 VAPOR RETARDER A. Install in accordance with provisions of section 07260 3.05 MEMBRANE APPLICATION A. Ballast Applied: 1. Place membrane so that wrinkles and buckles are not formed. Any wrinkles or buckles must be removed from the sheet prior to permanent attachment. Roof membrane shall 07540-8 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION be mechanically fastened immediately after it is rolled out, followed by welding to adjacent sheets. 2. Overlap roof membrane a minimum of 3” (15 cm) for side laps and 3” (15 cm) for end laps. 3. Install membrane so that the side laps run across the roof slope lapped towards drainage points. 4. All exposed sheet corners shall be rounded a minimum of 1”. 5. Use full width rolls in the field of roof and perimeter of the roof. 6. Membrane laps shall be heat-welded together. All welds shall be continuous, without voids or partial welds. Welds shall be free of burns and scorch marks. 7. Weld width shall be a minimum of 1-1/2” in width for automatic machine welding. Weld width shall be a minimum 2” in width for hand welding. 8. Supplemental membrane attachment is required at the base of all walls and curbs, and where the angle of the substrate changes by more than ten (10) degrees (2” in 12”). Roofing membrane shall be secured to the structural deck with appropriate Drill-Tec screws and plates spaced every 12” o.c. The screws and plates must be installed no less than ½” from the membrane edge. Alternatively, the roofing membrane may be turned up the vertical plane a minimum of 3” and secured with screws and termination bar Fastener spacing is the same as is used for in-lap attachment. The termination bar must be installed within 1-1/2” to 2” of the plane of the roof membrane, with a minimum of 1” of membrane extending above the termination bar. 9. Supplemental membrane attachment to the structural deck is required at all penetrations. Roofing membrane shall be secured to the deck with appropriate DrillTec screws and membrane plates. 10. Fasteners must be installed to achieve the proper embedment depth. Install fasteners without lean or tilt. 11. Install fasteners so that the plate or termination bar is drawn down tightly to the membrane surface. Properly installed fasteners will not allow the plate or termination bar to move (underdriving), but will not cause wrinkling of the membrane (overdriving). 3.06 FLASHINGS A. General: 1. All penetrations must be at least 24” (61 cm) from curbs, walls, and edges to provide adequate space for proper flashing. 2. Flash all perimeter, curb, and penetration conditions with coated metal, membrane flashing, and flashing accessories as appropriate to the site condition. 3. All coated metal and membrane flashing corners shall be reinforced with preformed corners or non-reinforced membrane. 4. Hot-air weld all flashing membranes, accessories, and coated metal. A minimum 2” wide (hand welder) weld is required. 5. Consult the EverGuard® Application and Specifications Manual or GAFMC Contractor Services for more information on specific construction details, or those not addressed in this section. B. Coated Metal Flashings: 1. Coated metal flashings shall be formed in accordance with current EverGuard construction details and SMACNA guidelines. 07540-9 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 2. Coated metal sections used for roof edging, base flashing and coping shall be butted together with a ¼” gap to allow for expansion and contraction. Hot-air weld a 6” wide reinforced membrane flashing strip to both sides of the joint, with approximately 1” on either side of the joint left un-welded to allow for expansion and contraction. 2” wide aluminum tape can be installed over the joint as a bond-breaker, to prevent welding in this area. 3. Coated metal used for sealant pans, scupper inserts, corners of roof edging, base flashing and coping shall be overlapped or provided with separate metal pieces to create a continuous flange condition, and pop-riveted securely. Hot-air weld a 6” wide reinforced membrane flashing strip over all seams that will not be sealed during subsequent flashing installation. 4. Provide a ½” hem for all exposed metal edges to provide corrosion protection and edge reinforcement for improved durability. 5. Provide a ½” hem for all metal flange edges whenever possible to prevent wearing of the roofing and flashing membranes at the flange edge. 6. Coated metal flashings shall be nailed to treated wood nailers or otherwise mechanically attached to the roof deck, wall or curb substrates, in accordance with construction detail requirements. C. Reinforced Membrane Flashings: 1. The thickness of the flashing membrane shall be the same as the thickness of the roofing membrane. 2. Membrane flashing may either be installed loose or fully adhered to the substrate surface in accordance with “Construction Detail Requirements”. 3. Apply bonding adhesive at a rate resulting in 60 square feet/gallon of finished roofing material for solvent-based bonding adhesives, and at a rate of 125 square feet/gallon of finished roofing material for water-borne bonding adhesive. Apply bonding adhesive to both the underside of the membrane and the substrate surface at 120 square feet per gallon (Solvent Based) and 250 square feet per gallon (Water Based). A greater quantity of bonding adhesive may be required based upon the substrate surface condition. The bonding adhesive must be allowed to dry until tacky to the touch before flashing membrane application. 4. Apply the adhesive only when outside temperature is above 40°F. Recommended minimum application temperature is 50°F to allow for easier adhesive application. 5. The membrane flashing shall be carefully positioned prior to application to avoid wrinkles and buckles. D. Un-reinforced Membrane Flashings: 1. Un-reinforced membrane is used to field-fabricate penetration or reinforcement flashings in locations where preformed corners and pipe boots cannot be properly installed. 2. Penetration flashings constructed of un-reinforced membrane are typically installed in two sections, a horizontal piece that extends onto the roofing membrane and a vertical piece that extends up the penetration. The two pieces are overlapped and hot-air welded together. 3. The un-reinforced membrane flashing shall be adhered to the penetration surface. Apply bonding adhesive at a rate resulting in 60 square feet/gallon of finished roofing material for solvent-based bonding adhesives, and at a rate of 125 square feet/gallon of finished roofing material for water-borne bonding adhesive. Apply bonding adhesive to both the underside of the membrane and the substrate surface at 120 square feet per gallon 07540-10 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION (Solvent Based) and 250 square feet per gallon (Water Based).The bonding adhesive must be allowed to dry until tacky to the touch before flashing membrane application. E. Roof Edges: 1. Roof edge flashings are applicable for gravel stop and drip edge conditions as well as for exterior edges of parapet walls. 2. Flash roof edges with coated metal flanges nailed 4” o.c. to pressure-treated wood nailers. Hot-air weld roof membrane to metal flanges. 3. When the fascia width exceeds 4”, coated metal roof edging must be attached with a continuous cleat to secure the lower fascia edge. The cleat must be secured to the building no less than 12” o.c. 4. Alternatively, roof edges may be flashed with a 2-piece snap on fascia system, adhering the roof membrane to a metal cant with bonding adhesive and face nailing the membrane 8” on center prior to installing a snap-on fascia (MA-206, 207). 5. Flash roof edge scuppers with a coated metal insert that is mechanically attached to the roof edge and integrated as a part of the metal edging. F. Parapet and Building Walls: 1. Flash walls with EverGuard PVC membrane adhered to the substrate with bonding adhesive, loose applied (Less than 18” in height) or with coated metal flashing nailed 4” on center to pressure-treated wood nailers. 2. Secure membrane flashing at the top edge with a termination bar. Water Block shall be applied between the wall surface and membrane flashing underneath all exposed termination bars. Exposed termination bars shall be mechanically fastened 8” on center; termination bars that are counter flashed shall be fastened 12” on center. 3. Roof membrane must be mechanically attached along the base of walls with screws and plates (deck securement) or screws and inverted termination bar (wall securement) at the following rate: Mechanically Attached Systems Fully Adhered Systems Ballast Applied Systems Per in-lap on center spacing, with a 12” maximum 12” on center 8” on center 4. All coated metal wall flashings and loose applied membrane flashings must be provided with separate metal counterflashings, or metal copings. 5. Metal counterflashings may be optional with fully adhered flashings depending on guarantee requirements. Exposed termination bars must be sealed with EverGuard® caulking. 6. Flash wall scuppers with a coated metal insert that is mechanically attached to the wall and integrated as part of the wall flashing. G. Curbs and Ducts: 1. Flash curbs and ducts with EverGuard PVC membrane adhered to the curb substrate with bonding adhesive, loose applied (Less than 18” in height) or with coated metal flashing nailed 4” on center to pressure-treated wood nailers. 2. Secure membrane flashing at the top edge with a termination bar. Water Block shall be applied between the curb/duct surface and membrane flashing underneath all termination bars. Exposed termination bars shall be mechanically fastened every 8”o.c.; termination bars that are counter flashed shall be fastened 12” on center. 07540-11 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION 3. Roof membrane must be mechanically attached along the base of walls with screws and plates (deck securement) or screws and inverted termination bar (wall securement) at the following rate: Mechanically Attached Systems Fully Adhered Systems Ballast Applied Systems Per in-lap on center spacing, with a 12” maximum 12” on center 8” on center 4. All coated metal curb flashings and loose applied membrane flashings must be provided with separate metal counterflashings, or metal copings. 5. Metal counterflashings may be optional with fully adhered flashings depending on guarantee requirements. Exposed termination bars must be sealed with EverGuard® caulking. H. Roof Drains: 1. Roof drains must be fitted with compression type clamping rings and strainer baskets. Original-type cast iron and aluminum drains, as well as retrofit-type cast iron, aluminum or molded plastic drains are acceptable. 2. Roof drains must be provided with a minimum 36” x 36” sump. Slope of tapered insulation within the sump shall not exceed 4” in 12”. 3. Extend the roofing membrane over the drain opening. Locate the drain and cut a hole in the roofing membrane directly over the drain opening. Provide a ½” of membrane flap extending past the drain flange into the drain opening. Punch holes through the roofing membrane at drain bolt locations. 4. For cast iron and aluminum drains, the roofing membrane must be set in a full bed of water block on the drain flange prior to securement with the compression clamping ring. Typical water block application is one 10.5 ounce cartridge per drain. 5. Lap seams shall not be located within the sump area. Where lap seams will be located within the sump area, a separate roof membrane drain flashing a minimum of 12” larger than the sump area must be installed. The roof membrane shall be mechanically attached 12” on center around the drain with screws and plates. The separate roof drain flashing shall be heat welded to the roof membrane beyond the screws and plates, extended over the drain flange, and secured as above. 6. Tighten the drain compression ring in place. 3.07 INTERLOCKING PAVERS A. Install interlocking concrete pavers in accordance with requirements determined by the most current revision of ASCE 7, and the paver manufacturer’s recommendations for stagger and interlock. B. Utilize perimeter securement of interlocking pavers and/or paver clips in accordance with the paver manufacturer’s requirements. 3.08 NON-INTERLOCKING PAVERS A. Install non-Interlocking concrete pavers in accordance with requirements determined by the most current revision of ASCE 7 and the paver manufacturer’s requirements. 07540-12 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION B. Utilize perimeter securement of non-interlocking pavers in accordance with the paver manufacturer’s requirements. 3.09 STONE BALLAST A. Install stone ballast in accordance with requirements determined by the most current revision of ANSI RP-4. 1. Minimum ballast application rate for #4 nominal 1-1/2" ballast is 10 lbs. per sq.ft. B. Minimum ballast application rate for #2 nominal 2-1/2" ballast is 13 lbs. per sq.ft. C. If existing ballast is to be reused, a minimum 3 oz. poly slip sheet shall be installed prior to ballast application. 3.10 TRAFFIC PROTECTION A. Install walkway pads/rolls at all roof access locations and other designated locations including roof-mounted equipment work locations and areas of repeated rooftop traffic. B. Walkway pads must be spaced 2" apart to allow for drainage between the pads. C. Fully adhere walkway pads/rolls to the roof membrane with solvent-based bonding adhesive, applied at the rate of 1 gal. per 100 sq. ft. to both the walkway and roof membrane surfaces. Press walkway in position once adhesive is tacky to the touch. D. Alternatively, walkway pads/rolls may be hot-air-welded to the roof membrane surface continuously around the perimeter of the pad/roll. 3.11 ROOF PROTECTION A. Protect all partially and fully completed roofing work from other trades until completion. B. Whenever possible, stage materials in such a manner that foot traffic is minimized over completed roof areas. C. When it is not possible to stage materials away from locations where partial or complete installation has taken place, temporary walkways and platforms shall be installed in order to protect all completed roof areas from traffic and point loading during the application process. D. Temporary tie-ins shall be installed at the end of each workday and removed prior to commencement of work the following day. 3.12 CLEAN-UP A. All work areas are to be kept clean, clear and free of debris at all times. B. Do not allow trash, waste, or debris to collect on the roof. These items shall be removed from the roof on a daily basis. 07540-13 Rev 09/04 GAFMC EVERGUARD® GUIDE SPECIFICATION C. All tools and unused materials must be collected at the end of each workday and stored properly off of the finished roof surface and protected from exposure to the elements. D. Dispose of or recycle all trash and excess material in a manner conforming to current EPA regulations and local laws. E. Properly clean the finished roof surface after completion, and make sure the drains and gutters are not clogged. F. Clean and restore all damaged surfaces to their original condition. END OF SECTION 07540-14 Rev 09/04