GAF MATERIALS CORPORATION
MATERIAL SAFETY DATA SHEET
MSDS # 2047
MSDS DATE: 06/03
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME:
EverGuard® EPDM Pourable Sealer Part A
CHEMICAL NAME/SYNONYM:
CHEMICAL FAMILY:
MANUFACTURER:
ADDRESS:
24 HOUR EMERGENCY
PHONE:
CHEMTREC PHONE:
PREPARED BY:
APPROVED BY:
None
Polybutadiene
GAF Materials Corporation
1361 Alps Road, Wayne, NJ 07470
800-424-9300
800-424-9300
NFPA HAZARD RATING:
1
1
0
Health
Flammable
Reactive
Special Hazards
OSHA HAZARDOUS:
Health
Flammable
Reactive
Special Hazards
Yes
HMIS HAZARD RATING:
1
1
0
No
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
CHEMICAL NAME
Non-hazardous as per 29
CFR 1910.1200
COMMON NAME
CAS #
% (BY WT)
EXPOSURE LIMITS
None
None
100.00
None Established
SECTION 3: HAZARDS IDENTIFICATION
PRIMARY ROUTE OF EXPOSURE:
SIGNS & SYMPTONS OF EXPOSURE
ACUTE HEALTH HAZARDS:
CHRONIC HEALTH HAZARDS:
CARCINOGENICITY:
Inhalation, Skin contact
May cause minor temporary eye or respiratory system irritation. May cause skin irritation if the
skin is scratched or cut.
None known.
No known adverse effects
None
SECTION 4: FIRST AID MEASURES
FIRST AID PROCEDURES:
NOTES TO PHYSICIANS OR FIRST AID
PROVIDERS:
PAGE 1 OF 4
For eyes, flush immediately with gentle stream of water for at least 15 minutes, preferable at
eye wash fountain. For skin contact, wash affected area thoroughly with soap and water. For
inhalation, remove to fresh uncontaminated air. In case of accidental ingestion, do not induce
vomiting. Get medical attention and advise the physician of the nature of the mater. The
mixture of parts A and B must be immediately removed fro the skin using Acetone.
N/a
GAF MATERIALS CORPORATION
MATERIAL SAFETY DATA SHEET
MSDS # 2047
MSDS DATE: 06/03
SECTION 5: FIRE-FIGHTING PROCEDURES
Water fog, foam, CO2 or Dry chemical.
Oxides or Carbon, Nitrogen and traces of Butadiene.
Wear impermeable protective clothing and self-contained breathing apparatus.
Toxic fumes and vapors may be evolved.
Heat from fire can generate flammable vapor. Vapors may be heavier than air.
May travel long distances along ground before igniting/ flashing back to vapor
source. Fine sprays/ mists may be combustible at room temperatures below
normal flash point. Polyurethane and Polyisocyanurates produced from this
product in combination with Phosphorus containing flame retardants may, when
pyrolysed at or above 300°C (572°F) produce toxic by-products.
SUITABLE EXTINGUISHING MEDIA:
HAZARDOUS COMBUSTION PRODUCTS:
RECOMMENDED FIRE FIGHTING PROCEDURES:
UNUSUAL FIRE & EXPLOSION HAZARDS:
SECTION 6: ACCIDENTAL RELEASE MEASURES
ACCIDENTAL RELEASE MEASURES:
N/a
SECTION 7: HANDLING AND STORAGE
HANDLING AND STORAGE:
OTHER PRECAUTIONS:
STEPS TO BE TAKEN IN CASE MATERIAL IS
REALEASED OR SPILLED:
PRECAUTIONS TO BE TAKEN IN HANDLING
& STORAGE:
N/a
N/a
Wear protective equipment including rubber boots, rubber gloves, rubber apron, and a selfcontained breathing apparatus in the pressure demand mode or supplied-air respirator. If
the spill or leak is small, a full face piece air-purifying cartridge respirator equipped for
organic vapors may be satisfactory. In any event, always wear eye protection. Extinguish
all ignition sources and ensure that all handling equipment is electrically grounded. For
small spills or drips, mop or wipe up and dispose of in a DOT-approved waste container.
For large spill, contain by diking with soil or other non-combustible absorbent materials
and then pump into DOT approved wasted containers; or absorb with non-combustible
sorbent material. Place residue in DOT-approved waste containers. Keep out of sewers,
storm drains, surface water, and soil. Comply with all applicable governmental regulations
on spill reporting and handling and disposal of waste.
Store in a cool, dry area away from direct heat. Keep containers tightly closed when not in
use.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS:
VENTILATION:
RESPIRATORY PROTECTION:
EYE PROTECTION:
SKIN PROTECTION:
OTHER PROTECTIVE CLOTHING OR
EQUIPMENT:
WORK HYGIENIC PRACTICES:
EXPOSURE GUIDELINES:
PAGE 2 OF 4
N/a
Use in a well ventilated areas.
No special requirements are expected under normal conditions and use.
Wear safety glasses or chemical splash goggles when pouring, mixing or applying
this material.
Wear chemical resistant gloves when pouring, mixing or applying this material.
Impervious clothing and boots if appropriate.
Wash exposed skin prior to eating, drinking or smoking and at the end of each shift.
Wash contaminated clothing prior to reuse.
N/a
GAF MATERIALS CORPORATION
MATERIAL SAFETY DATA SHEET
MSDS # 2047
MSDS DATE: 06/03
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Light gray, viscous liquid, mild odor.
APPEARANCE & ODOR:
365°F
FLASH POINT:
LOWER EXPLOSIVE LIMIT:
TCC
METHOD USED:
UPPER EXPLOSIVE LIMIT:
Unknown
EVAPORATION RATE:
BOILING POINT:
Unknown
pH (undiluted product):
MELTING POINT:
Partially
SOLUBILITY IN WATER:
SPECIFIC GRAVITY:
Unknown
VAPOR DENSITY:
PERCENT VOLATILE:
Nil mm Hg @ 20°C
VAPOR PRESSURE:
VOLATILE ORGANIC COMPOUNDS (VOC)
N/a
WITH WATER (LBS/GAL):
WITHOUT WATER (LBS/GAL):
N/a
MOLECULAR WEIGHT:
Unknown
Unknown
Unknown
Unknown
1.288 (Water=1)
Unknown
N/a
SECTION 10: STABILITY AND REACTIVITY
THERMAL STABILITY:
CONDITIONS TO AVOID (STABILITY):
STABLE
UNSTABLE
Strong oxidizers, moisture, acid and bases. This material in contact with Phosphorus may
produce by-products.
N/a
INCOMPATIBILITY (MATERIAL TO
AVOID):
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
HAZARDOUS POLYMERIZATION:
N/a
Will not occur
_________________________________________________________________________________________________________________
SECTION 11: TOXICOLOGICAL INFORMATION
TOXICOLOGICAL INFORMATION:
N/a
SECTION 12: ECOLOGICAL INFORMATION
ECOLOGICAL INFORMATION:
N/a
_________________________________________________________________________________________________________________
SECTION 13: DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHOD:
RCRA HAZARD CLASS:
N/a
N/a
SECTION 14: TRANSPORT INFORMATION
U.S. D0T Highway
Transportation
U.S. DOT Water Transpiration
PAGE 3 OF 4
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENT:
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
Not Applicable
Not Applicable
Not Applicable
Not Applicable
GAF MATERIALS CORPORATION
MATERIAL SAFETY DATA SHEET
U.S. DOT Air Transpiration
MSDS # 2047
MSDS DATE: 06/03
LABEL STATEMENT:
Not Applicable
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENT:
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
PROPER SHIPPING NAME:
HAZARD CLASSIFACTION:
ID NUMBER:
LABELS REQUIRED:
OTHER REQUIREMENTS:
Not Applicable
Not Applicable
Not Applicable
Not Applicable
Not Applicable
OTHER REGULATORY
AGENCIES
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS:
TSCA (TOXIC SUBSTANCE CONTROL ACT):
CERCLA (COMPREHENSIVE RESPONSE
COMPENSATION, AND LIABILITY ACT):
SARA TITLE III (SUPERFUND AMENDMENTS AND
REAUTHORIZATION ACT):
311/312 HAZARD CATEGORIES:
313 REPORTABLE INGREDIENTS:
N/a
N/a
N/a
N/a
N/a
N/a
_________________________________________________________________________________________________________________
SECTION 16: OTHER INFORMATION
ADDITIONAL COMMENTS:
DATE OF PREVIOUS MSDS:
CHANGES SINCE PREVIOUS MSDS:
TELEPHONE NUMBER FOR ADDITIONAL
INFORMATION:
PAGE 4 OF 4
The composition of this product by weight is approximately: Polyol (40-65%), Calcium
Carbonate (30-45%), Amorphous Silica (3-12%), Polybutene (1-10%).
10/02
Phone Numbers
800-766-3411