MergePoint™ 5224/5240 Service Processor Managers
Release Notes
Version 3.1.0-1
March 27, 2007
This document outlines:
1. Update Instructions
2. Appliance Firmware Version and Language Support Information
3. Enhancements
4. Fixes
5. Known Issues
=============================================================================
Update Instructions
=============================================================================
Please refer to your Installer and Administrator Guide for detailed instructions to update the
MergePoint 5224/5240 appliances to version 3.1.0-1. The firmware is based on the MergePoint
5224/5240 firmware V3.1.0, and serves as an upgrade to it or to a Cyclades® OnBoard firmware
V1.1.0, V3.0.0 or V3.0.0-1.
An upgrade to the Cyclades OnBoard plug-in for DSView® 3 management software is not required.
However, some new features of the MergePoint 5224/5240 appliance will not be available through
DSView 3 software if the previous version of the plug-in is used. In order to have all features from
MergePoint 5224/5240 appliance firmware available through DSView 3 software, DSView 3 software
version 3.4 and MergePoint 5224/5240 plug-in for DSView 3 version 1.2.0 are required. An appliance
firmware package to upgrade from DSView 3 software is also available.
Before installing MergePoint 5224/5240 firmware version 3.1.0-1, please ensure that you have a
backup of your existing configuration safely stored.
The upgrade process works from Cyclades OnBoard appliance firmware V1.1.0, V3.0.0, V3.0.0-1 and
V3.1.0. If upgrading from any other version, please first upgrade one of these versions before
upgrading to V3.1.0-1. Optionally, you can upgrade to MergePoint 5224/5240 firmware V3.1.0-1 and
restore the configuration to factory default.
If you created or edited the expect script or service processors templates, the upgrade procedure
may fail. If this is the case, please check the configuration upgrade log file (/etc/configuration/log) to
see if there is any error. You may need to fix the affected files by either applying the changes again or
using the original file provided in the MergePoint 5224/5240 firmware V3.1.0-1.
=============================================================================
Appliance Firmware Version and Language Support Information
=============================================================================
Appliance/Product
Firmware Type
Version
Filename
Language
MergePoint 5224/5240
Opcode
V_3.1.0-1
fl0569002.bin
English
=============================================================================
Enhancements
=============================================================================
This is a patch release for MergePoint 5224/5240 firmware V3.1.0. There are no new features in this
release.
The version V3.1.0 is based on Cyclades OnBoard appliance firmware v3.0.0 and contains the
following enhancements:
1. The Cyclades OnBoard appliance has been rebranded to the MergePoint 5224/5240 service
processor manager.
2. DirectCommand: DirectCommand allows transparent access to the native user interface of a
service processor (SP), while still enforcing the authentication and authorization rules defined in
the MergePoint 5224/5240 appliance regarding access to that specific SP. DirectCommand can
be used to access the SP’s native web interface, from which the user may access services
provided by the SP, such as a Virtual Media and remote KVM.
3. Support to IPMI 2.0 SPs.
4. Support to Sun ALOM SPs.
5. Web interface improvements:
a. Access page shows one SP per line, providing a cleaner user interface.
b. Additional SP information such as its IP address and device type are displayed, making it
easier to identify the specific SP the user wishes to access.
c. An action menu with the available functions for that SP is displayed right from the first access
page, allowing faster access to the SP functionality.
d. List of active sessions that allows admin users to see and close sessions.
e. Configurable web interface timeout.
6. Ability to create new SP types or modify existing ones, which provides for more flexibility and ease
of use when trying to communicate with SPs that are not standard or otherwise not supported by
the MergePoint 5224/5240 appliances. The parameters that can be configured in an SP type
include protocol (telnet, SSH or IPMI), DirectCommand settings and template type.
7. Configurable option to enable or disable multiple concurrent SoL sessions to a specific SP.
8. LDAP Group authorization retrieved from ‘memberof’ attribute, in addition to the ‘info’ attribute
available in previous versions.
9. Support for AIDP (Avocent Install and Discovery Protocol).
=============================================================================
Fixes
=============================================================================
This release contains the following fixes:
1. Zoneinfo files were updated to Jan/2007 versions in order to comply with the changes in the US
Daylight Savings Time (Energy Policy Act of 2005).
2. Failure on upgrade from Cyclades OnBoard firmware V1.1.0 is now fixed.
3. SoL on DRAC now properly responds to <ENTER> keystrokes.
4. Java applets for Service Processor access and DirectCommand are signed by an official Avocent
certificate.
5. Event notification reports syslog messages to DSView 3 management software without failure.
6. List of SP families in the Web Interface is now dynamic, according to the SP families available in
the appliance configuration.
7. Server-based group authorization now adds the authenticated user to the supplied groups only if
the user was provided by the authorization server.
NOTE: Before authorization, the remotely authenticated user will be removed from all groups in
the current appliance configuration and re-added only to the groups provided by the authorization
server. The users/groups configuration will not mix local users and remote users added by
authentication servers.
8. SoL connection to ALOM works regardless of whether another user is connected in the host
console.
Additionally, V3.1.0 fixes the following issues:
1. Power Status command returns consistent response, regardless of the SP type.
2. Target device names can include capital letters.
3. Assign proper default broadcast address when configuring Ethernet interfaces.
4. Save correct user and password when configuring from Web Wizard pages.
5. Several issues configuring SNMP parameters from Web interface.
6. Removed ‘Back’ option from spshell menu when connecting directly to a target device.
7. Appliance sends event 58 to DSView 3 software every time a device console connection ends.
8. Connections to the appliance or to the SPs from DSView 3 software duplicated the end of line,
causing the prompt to be shown twice. This is now fixed, and such connections behave properly.
=============================================================================
Known Issues
=============================================================================
This release contains the following known issues:
1. Some SPs do not send any response to power on/off/cycle commands. These commands may
result in an “empty” pop-up Web page. The same may happen with power status for iLO.
2. Target names cannot have spaces or tilde (‘~’). If a target name has spaces or tilde, the operation
to push target names to DSView 3 software will fail.
3. The appliance’s IP address for the primary Ethernet interface (eth0) must be used in the Add
Appliance Wizard. If the secondary Ethernet (eth1) or any of the sub-interface IP addresses are
used, data logging and syslog event notification will not work.
4. Users with admin privileges can access either the MergePoint 5224/5240 plug-in for DSView 3
software or the MergePoint 5224/5240 WebUI, but not both. The appliance accepts only one
admin user logged in at a time. Admin users may disconnect a DSView 3 software session when
connecting to the appliance via WebUI or CLI and take over another admin session. Halting a
DSView 3 session may cause loss of configuration and/or failure in the DSView 3 operation.
DSView 3 software will always take over another admin session, whether it is from the WebUI or
the CLI, without warning.
5. If the condition to trigger a sensor alarm happens multiple times within the configured time interval
for sensor alarms, the user will receive the sensor alarms at the right time, but there will be
multiple alarms instead of just the last one.
6. Shared secret is not deleted from the configuration file when the IPSec connection is deleted.
7. Local/<any> authentication methods require local account. The authentication will succeed by
providing either the local or the remote password, but the user must exist in the appliance local
accounts for authorization purposes.
8. When upgrading from Cyclades OnBoard firmware V1.1.0 with no device configured, the
MergePoint 5224/5240 firmware V3.1.0-1 will create an invalid device called 'uniqueid'. You can
remove it by using either the Web interface or the CLI.