Full Facility Surge Protection – Fire Alarm Panels An Application Guide

advertisement
An Application Guide
From the Experts in
Business-Critical Continuity™
Full Facility Surge Protection –
Fire Alarm Panels
Application Guide
Fire Alarm Panels
A fire alarm control panel (FACP), is the central control device that receives information from input devices such as
(smoke detectors, heat detectors, manual fire alarm stations, etc.). This panel then processes the information to
trigger an output device (bells, horns, or strobes). "Dirty Power" can damage fire control panels, its sensors and even
output devices, resulting in serious safety issues.
Emerson Network Power recommends surge protection on any copper wire circuit entering or leaving a fire panel to
protect against the damaging effects of lightning, spikes, and surges. Typical installation may be close-nipple up to a
panel/circuit or hardwired in parallel up to power supply input terminal screws with leads dressed as short as possible.
Emerson Network Power also recommends surge protection to be installed on all data and phone lines, in order that
fire alarm systems will be guarded from what we commonly refer to as “backdoor” transients and noise. These
transients occur more frequently than high impulse occurrences such as lightning strikes and are usually generated
from other equipment operating within a facility.
The PowerSure™ FAS-120AC surge suppressor is designed to protect AC distribution
panel circuits or 120V power supplies feeding sensitive electronic equipment.
The Edco™ HSP121BT-1RU is a hardwire 3-stage hybrid protector, featuring a 15 amp
replaceable fuse, failure indicator and noise filtering. In the rare event of the unit failing, the
equipment is removed from the load.
The Edco FAS-1-043 is a multi-stage single pair surge suppressor designed for high exposure
applications. This product was specifically designed to meet multiple low voltage protection
applications in the fire/security and CCTV industries. This unit will work for 24 volts AC or DC,
up to 2.5 amps.
The Edco SLCP-043 is a four-wire module designed to protect Signaling Line Circuits (SLC).
The device has 0 ohms of resistance and offers line to ground protection. Easily plugs into
the Edco PCB1B-WKEY base.
An Edco PC642 surge suppressor is recommended on the PTZ data lines at the head end
(DVR), as well as the camera end. This is a two-pair (four-wire) module implementing threestage hybrid technology, allowing it to protect against multiple surge events without
replacement. The Edco PC642 easily plugs into the Edco PCB1B-WKEY base.
Edco
HSP121BT-1RU
PowerSure
FAS-120AC
Edco SRS-232
Edco FAS-1-043
Edco SLCP-043
The Edco LCDP is designed to conveniently protect eight- wire, low voltage data circuits and
employs two RJ-45 jacks for easy installation.
The Edco PHC-043 is a rugged series hybrid designed to protect two pairs of wires
specifically for alarm and security systems where operating currents can be as high as
5 Amps. The Edco PHC-043 easily plugs into the Edco PCB1B-WKEY base.
Surge suppression is needed to protect both
phone lines of a commercial fire alarm panel. The
Edco PC2-TEL is a solid state, two-line telephone
interface protector module. This unit is specifically
designed to protect both phone lines required by
commercial fire/security alarm panels. Easily plugs Edco PC2-TEL
into the Edco PCB1B-WKEY base.
Edco PHC-043
Edco PC642
Edco LCDP
Type of Device
Basic Panel Surge Protection
Premium Panel Surge Protection
Post Indicator Valve Circuit
SLC Loop
RS-485 Network
Data Circuit
Notification Circuit
Part Number
FAS-120AC
HSP121BT-1RU
FAS-1-043HC
SLCP-43 with PCB1B-WKEY base
PC642C-008LC
LCDP
PHC-043 with PCB1B-WKEY base
Telephone Line
PC2-TEL with PCB1B-WKEY base
IEEE Standard
Fire Alarm Panel Protection Application Diagram
8.6.4 “…it is recommended that additional
surge protective devices of listed Category “B”
or Category “A,” as specified in IEEE Std C62.411991, be applied to downstream electrical
switchboards
and
panelboards,
and
panelboards on the secondary side of
separately derived systems if they support
communications, ITE, signaling, television, or
other form of electronic load equipment.”
100 Emerson Parkway
Binghamton, NY 13905
P (607) 721 8840
P (800) 288 6169
F (607) 722 8713
E contactsurge@emerson.com
AG-22017
Rev. 1 1/13
EMERSON NETWORK POWER SURGE PROTECTION INC MAY UPDATE OR REVISE PRICING AND PRODUCT INFORMATION AT ANY TIME PRIOR TO
RECEIPT AND ACCEPTANCE OF A CUSTOMER ORDER. SUCH UPDATES OR REVISIONS SHALL BE COMMUNICATED ELECTRONICALLY TO CURRENT
REPRESENTATIVES. DAYS TO SHIP MAY VARY DUE TO SIZE OF ORDER. ADDITIONAL PRODUCT DESIGNS ARE AVAILABLE,
PLEASE CONTACT THE FACTORY FOR ASSISTANCE.
Download