Place of Birth

advertisement
GUILBERT A. MARZO
Current Address:
Villa 13 Amir Bin Othman street, Matar Qadeem, Doha
Qatar
Mobile Number:
+97433238928
Email address:
guilmarz@yahoo.com.ph
PERSONAL DATA
Date of Birth:
Place of Birth:
Nationality:
Marital Status:
September 03, 1984
Surallah, South Cotabato
Filipino
Single Male
EDUCATION
Bachelor of Science in Electronics and Communications Engineering (2006),
Notre Dame of Marbel University.
WORK EXPERIENCE
Inclusive dates:
September 2006 to January 2014
Employer:
DOLE Phils. INC.
Type of Business: Food Manufacturing Industry
Position:
Instrument/Electrical Technician
DUTIES and RESPONSIBILITIES
 Instrument planning, lay-out, design and estimate.
 Programming, wiring and installation, troubleshooting and maintenance of
PLC (Programmable Logic Controller)
 Set-up and Configure, wiring and installation, calibration and
troubleshooting of temperature controller and chart recorder, inkjet printer,
metal detector, frequency drive or VFD (variable frequency drive), level
controller, PH meter, soft starter, weighing scale, and any related industrial
instruments.
 Support production operation by giving them maximum technical services in
case of any trouble of machine or equipment in order to minimize the
downtime.
 Improvement of existing operation by placing interlock timers, sensors or
reprogramming and revision of the system for efficiency, quality, safety and
energy conservation reason.
 Upgrading of traditional relay controls in PLC operated system such as
cooker/cooler, PVS seamer and whalloon palletizer.
 Verification of truck scale and all weighing scale in the cannery ensuring
that it is within the standards and tolerances.
 Do servicing and maintenance schedule of printers, canalyzers, pneumatic
and pressure regulator valves.
 Calibration and verification of metal detector ensure that it is within the
threshold limits.
 Installation of RTD/ Thermocouple, IP transducer and modulating valve for
temperature recorder/controller.
 Observe process operation and impose an idea for the improvement of
process in relation to efficiency, quality, safety, and energy conservation.
 Ensure good printing quality of all can printers in the line.
 Do pre-operational check of all controllers, valves, pressure gauges, sensors
and other instrument used in the line. See to it that these are in good
condition prior to operation.
 Electrical project planning lay-out and design.
 Overhauling of induction motors
 Operate generator set during power outage.
 Power plant monitoring every hour, such as; line to line voltage, amperage
of every feeders, kilowatt-hour, power factor and capacitor bank.
 Does preventive maintenance schedule of all electrical motors in the cannery
such as; megger testing, measure voltage/current/resistance and other
electrical parameters if necessary, then servicing and motor alignment.
 Do visual and hearing observation on all running motors. Observe if there
are sign of excessive noise, vibration or overheating. Schedule for servicing
if found abnormal.
 Fixing of all cannery deficiency such as; changing of busted lightings and
replacing of corroded electrical conduit.
 Harnessing of wires.
SKILLS
 Installs, services and repairs lighting fixtures, electrical panels, outlets and
wiring.
 Lay conduit for low and mid voltage electric lines.
 Reads electrical circuit diagrams.
 Operates power hand tools and other specialized electrical equipment.
 Installs, repairs and services specialized electrical equipment and machinery.
 Constructs and maintains service equipment.
 Preventive Maintenance and overhauling of electrical motors
 Testing and installation of electrical motors













Corrective in defective lighting
Harnessing of wires
Servicing of pneumatic cylinders and pneumatic valves
Configuration of Frequency Drives
Wiring and troubleshooting of industrial controls
Installation of soft starters
Configuration of ABB controllers
Testing and installation of RTD and Thermocouple
Installation of IP
Servicing of Modulating valves
Wiring and testing of AC/DC sensors
PLC programming and wiring
Computer literate
ACHIEVEMENTS
Passed the Registered Master Electrician Board Examination – 2012
TRAININGS / SEMINARS
DATE HELD
Basic PLC Programming (OMRON)
-
August 13, 2009
Basic HMI Programming (OMRON)
-
August 14, 2009
Establishment of Thermal Processes for
-
April 5-8, 2011
-
July 25, 2013
Canned Foods
Energy Saving & Preventive Maintenance
in Pneumatic System (SMC)
Download