Chapter 20
Electric Current and
Resistance
Units of Chapter 20
Batteries and Direct Current
Current and Drift Velocity
Resistance and Ohm’s Law
Electric Power
20.1 Batteries and Direct Current
Electric current is the
flow of electric
charge. A battery is a
source of electric
energy—it converts
chemical energy into
electric energy.
20.1 Batteries and Direct Current
In a complete circuit, electrons flow from the
negative electrode to the positive one.
The positive electrode is called the anode; the
negative electrode is the cathode.
A battery provides a constant source of
voltage—it maintains a constant potential
difference between its terminals.
20.1 Batteries and Direct Current
The potential difference
between the battery
terminals when the battery
is not connected to
anything is called the
electromotive force, emf.
20.1 Batteries and Direct Current
The actual terminal voltage of the battery is
always less than the emf, due to internal
resistance. Usually the difference is very
small.
20.1 Batteries and Direct Current
The actual terminal voltage of the battery is
always less than the emf, due to internal
resistance. Usually the difference is very
small.
Vterm = ؏ - (IR)
Where ؏ is the emf,
Vterm is the terminal voltage,
& IR is the internal voltage drop
More on this later… 20.3
20.1 Batteries and Direct Current
When batteries are
connected in
series, the total
voltage is the sum
of the individual
voltages.
20.1 Batteries and Direct Current
When batteries of
equal voltage are
connected in parallel,
the total voltage does
not change; each
battery supplies part
of the total current.
20.1 Batteries and Direct Current
20.1 Current and Drift Velocity
Current is the time rate of flow of charge.
SI unit of current: the ampere, A
20.1 Current and Drift Velocity
Historically, the direction of current has been
taken to be from positive to negative; this is
opposite to the way electrons flow. However,
this seldom matters.
20.1 Current and Drift Velocity
Electrons do not flow like water in a pipe. In
the absence of voltage, they move randomly
at high speeds, due to their temperature.
When a voltage is
applied, a very small
drift velocity is added
to the thermal
motion, typically
around 1 mm/s; this
is enough to yield the
observed current.
20.2 Resistance and Ohm’s Law
If there is a potential difference across a
conductor, how much current flows?
The ratio between the voltage and the
current is called the resistance.
SI unit of resistance: the ohm, Ω
20.2 Resistance and Ohm’s Law
An ohmic material is one whose resistance
is constant.
20.2 Resistance and Ohm’s Law
Ohm’s law is valid only for ohmic materials:
The resistance of a
particular object
depends on its
length, crosssectional area,
material, and
temperature.
20.3 Resistance and Ohm’s Law
As expected, the resistance is proportional
to the length and inversely proportional to
the cross-sectional area (why?):
The constant ρ is called the resistivity,
and is characteristic of the material.
20.3 Resistance and Ohm’s Law
In this table, you can easily see the
differences between the resistivities of
conductors, semiconductors, and insulators.
20.4 Electric Power
Power, as usual, is the rate at which work is
done. For work done by electricity:
Rewriting,
For ohmic materials, we can write:
20.4 Electric Power
So, where does this power go? It is changed
to heat in resistive materials.
20.4 Electric Power
Electric appliances
are rated in watts,
assuming standard
household voltage.
20.4 Electric Power
20.4 Electric Power
The electric company
typically bills us for
kilowatt-hours (kWh),
a unit of energy.
We can reduce our
energy usage by buying
efficient appliances.
Review of Chapter 20
A battery produces emf; positive terminal is
the anode, negative is the cathode.
emf is measured in volts; it is the number of
joules the battery supplies per coulomb of
charge.
An electric current can exist only in a
complete circuit.
Resistance:
Review of Chapter 20
Ohm’s law is obeyed if the resistance is
constant:
The resistance of an object depends on its
length, cross-sectional area, and
resistivity.
Review of Chapter 20
Power is the rate at which work is done.