Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16134 Rev A
SECTION 28 23 29
1080p TRUE DAY/NIGHT H.264 INDOOR IR MINIDOME IP CAMERA, H3D2SR2
PART 1 GENERAL
1.1
SECTION INCLUDES
A.
1.2
Provide a color 1080p true day/night H.264 indoor IR minidome IP camera system for video
surveillance, including design, supply, installation, and commissioning.
RELATED SECTIONS
NOTE TO SPECIFIER: Include related sections as appropriate if video surveillance system is integrated
to other systems.
1.3
A.
Section 26 05 00: Common Work Results for Electrical, for interface and coordination with
building electrical systems and distribution.
B.
Section 28 05 13: Conductors and Cables for Electronic Safety and Security, for cabling
between system servers, panels, and remote devices.
C.
Section 28 05 28: Pathways for Electronic Safety and Security, for conduit and raceway
requirements.
D.
Section 28 23 23: Video Surveillance Systems Infrastructure.
E.
Section 28 23 29: Video Surveillance Remote Devices and Sensors.
REFERENCES
A.
Reference Standards: Provide systems that meet or exceed the requirements of the
following publications and organizations as applicable to the work of this Section.
1.
Canadian ICES-003.
2.
Canadian Standards Association (CSA).
3.
Conformity for Europe (CE).
4.
Consultative Committee for International Radio (CCIR).
5.
Electronic Components Industry Association (ECIA).
6.
Federal Communications Commission (FCC).
7.
Institute of Electrical and Electronics Engineers (IEEE).
28 23 29-1
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
1.4
8.
International Organization for Standardization (ISO).
9.
National Television Systems Committee (NTSC).
10.
Phase Alternating Line (PAL).
11.
Underwriters Laboratories Inc. (UL).
Guide Specifications in CSI Format
800-16134 Rev A
SYSTEM DESCRIPTION
A.
The indoor IR minidome IP camera shall use a compact one-piece enclosure that can be
mounted directly to a wall or ceiling. In-ceiling, pendant, and pole mounting options shall also
be available.
B.
The indoor IR minidome IP camera shall offer 1080p resolution, a 1/2.7-inch CMOS
progressive scan imager, 24 IR LEDs, true day/night functionality, 3D digital noise reduction
(3DNR), a 3–9 mm motorized focus and zoom lens, quad stream compression, camera
tamper detection and video motion detection, privacy masking, and microSDHC card
support.
28 23 29-2
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
1.5
1.6
1.7
Guide Specifications in CSI Format
800-16134 Rev A
SUBMITTALS
A.
General: Submittals shall be made in accordance with the Conditions of the Contract and
Submittal Procedure Section.
B.
Manufacturer’s Product Data: Submit manufacturer’s data sheets indicating systems and
components proposed for use, including instruction manuals.
C.
Shop Drawings: Submit installation drawings, including connection diagrams for interfacing
equipment, list of connected equipment, and locations for major equipment components.
Shop drawings shall indicate surrounding construction as provided for the Project.
D.
Project Record Drawings: Indicate location of equipment and wiring on project record
drawings. Submit an electronic version of the project record drawings not later than
Substantial Completion of the Project.
E.
Operation and Maintenance Data: Submit manufacturer’s operation and maintenance data
customized to the system installed. Include operator manuals.
F.
Field Tests: Submit results of field testing of every device, including date, testing personnel,
retesting date (if applicable), and confirmation that every device passed field testing.
G.
Maintenance Service Agreement: Submit a sample copy of the manufacturer’s maintenance
service agreement, including cost and services for a one year period for Owner’s review.
Maintenance shall include, but not be limited to, labor and materials to repair the system,
tests and adjustments, and regular inspections.
QUALITY ASSURANCE
A.
Qualifications: Manufacturers shall have a minimum of 10 years full time experience in
manufacturing and maintaining video surveillance systems. Manufacturer shall provide tollfree technical assistance and support available 24/7. Installers shall have a minimum of
2 years experience installing similar systems and shall be acceptable to the manufacturer of
the video surveillance system.
B.
Regulatory Requirements:
1.
Emissions: FCC, Part 15, Class A; CE (EN 55022).
2.
Immunity: CE (EN 50130-4).
3.
Safety: CE (EN 60950-1); UL/CSA 60950-1.
DELIVERY, STORAGE, AND HANDLING
A.
General: Delivery, storage, and handling of the product shall be in accordance with the
manufacturer’s recommendations.
B.
Ordering: The manufacturer’s ordering instructions and lead-time requirements must be
followed in order to avoid installation delays.
C.
Packing and Shipping: Deliver product in the manufacturer’s original, unopened, undamaged
packaging with identification labels intact.
28 23 29-3
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
D.
1.8
Storage and Protection: Store and handle product in accordance with the manufacturer’s
requirements in a facility where environmental conditions are within the recommended limits.
PROJECT CONDITIONS
A.
Environmental Requirements: Comply with environmental requirements and
recommendations of manufacturer for proper installation of products.
B.
Temperature Criteria:
C.
1.9
Guide Specifications in CSI Format
800-16134 Rev A
1.
Operating temperatures shall be between 14° F (–10° C) and 122° F (50° C).
2.
Storage temperatures shall be between –4° F (–20° C) and 158° F (70° C).
Power Requirements: Input voltage shall be 12 V DC, 24 V AC, or PoE IEEE 802.3af Type 1,
Class 0.
WARRANTY
A.
Manufacturer’s Guarantee: Three (3) years from the manufacture date code under normal
use and service for the video surveillance system.
28 23 29-4
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16134 Rev A
PART 2 PRODUCTS
2.1
2.2
2.3
MANUFACTURERS
A.
Specified Manufacturer: Honeywell, www.honeywell.com/security.
B.
Accepted Part Numbers:
1.
H3D2SR2.
2.
H3D2SR2X.
SYSTEM COMPONENTS
A.
Specified Product: H3D2SR2(X) indoor IR minidome IP camera.
B.
Cabling.
OPERATIONAL REQUIREMENTS
A.
The indoor IR minidome IP camera system shall meet or exceed the following camera
specifications:
1.
Image Sensor: 1/2.7-inch CMOS.
2.
Total Pixels: 1920 (H) × 1080 (V).
3.
Lens Type: 3–9 mm motorized focus and zoom, F1.2 (wide)/F2.1 (tele).
4.
Angle of View:
5.
a.
Horizontal: 108° (wide) to 41° (tele).
b.
Vertical: 75° (wide) to 24° (tele).
Minimum Illumination:
a.
Color: 0.45 lux @ 50 IRE, F1.2 (IR off).
b.
B/W: 0.02 lux @ 50 IRE, F1.2 (IR off).
6.
Shutter Speed: 1 to 1/10,000 seconds.
7.
Video Output: Composite, 1.0 VP-P, 75 ohms.
8.
IR LEDs: 850 nm, 24 LEDs.
9.
IR Illumination Distance: Up to 50 ft (15 m), depending on scene reflectance and
camera settings.
10.
White Balance: Auto/ATW/Manual.
11.
Signal-to-Noise Ratio: 50 dB or higher (AGC off).
12.
Synchronization: Internal.
28 23 29-5
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16134 Rev A
B.
The indoor minidome IP camera system shall provide 1080p high definition resolution.
C.
The indoor minidome IP camera system shall provide true day/night functionality with an
infrared (IR) cut filter for day mode.
D.
The indoor minidome IP camera system shall provide 3D digital noise reduction, smart
picture quality (SPQ), backlight compensation, automatic light compensation, automatic gain
control, flickerless mode, and digital slow shutter.
E.
The indoor minidome IP camera system shall provide fully configurable motion detection
settings.
F.
The indoor minidome IP camera system shall provide up to 5 fully configurable privacy
zones to mask sensitive areas of a video image.
G.
The indoor IR minidome IP camera system shall provide remote digital zoom adjustment (8×).
H.
The indoor minidome IP camera system shall support remote firmware updates.
I.
The indoor minidome IP camera system shall support 20 user accounts and multiple user
access levels with password protection.
J.
The indoor minidome IP camera system shall support the ONVIF (Profile S) specification for
interoperability between network video products.
K.
The indoor minidome IP camera system shall support IPv4/v6, TCP/IP, UDP, RTP, RTSP,
HTTP, HTTPS, ICMP, FTP, SMTP, DHCP, PPPoE, UPnP, IGMP, SNMP, IEEE 802.1x,
QoS, ONVIF, SSL, DNS, and NTP protocols.
L.
The indoor minidome IP camera system shall provide quad H.264 and/or H.264/MPEG video
streams simultaneously. It shall also provide controllable frame rates and bandwidth, and
constant or variable bit rates.
M.
The indoor minidome IP camera system shall provide Network Time Protocol (NTP)
synchronization support.
N.
The indoor minidome IP camera system shall support embedded date/time stamps in the
video stream.
O.
The indoor minidome IP camera system shall support Internet Explorer 6 or later (32-bit),
Chrome, Firefox, and Safari web browsers.
P.
The indoor minidome IP camera system shall support Windows 7 (32-bit/64-bit), Windows
Vista, and Windows XP operating systems.
Q.
The indoor minidome IP camera system shall support input and output alarm contacts and
bidirectional audio communication.
R.
The indoor minidome IP camera system shall support a microSDHC card (up to 32 GB,
Class 10) for event or scheduled recording. The administrator shall have the ability to turn
the recording function on or off through the web interface.
IMPORTANT: Honeywell is not responsible for any damage incurred to files saved on the
microSDHC card, regardless of the cause.
28 23 29-6
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
2.4
Guide Specifications in CSI Format
800-16134 Rev A
S.
The indoor minidome IP camera system shall provide 12 V DC, 24 V AC, or PoE IEEE
802.af options.
T.
The indoor minidome IP camera system shall have a 3-axis (pan/tilt/rotation) gimbal bracket
for precise camera positioning.
U.
The indoor minidome IP camera system housing shall be constructed of polycarbonate and
the color shall be RAL 9003.
SYSTEM HARDWARE
A.
The indoor IR minidome IP camera system shall have the following mechanical
specifications:
1.
Unit Dimensions (W × H): 5.87 × 5.14 inches (149.0 × 130.5 mm).
2.
Unit Weight: 1.5 lb (0.7 kg).
3.
Connectors:
4.
B.
Power Input: 3-pin terminal block.
b.
Video Output (AUX): BNC connector (75 ohms).
c.
Network: RJ45 connector.
d.
Alarm I/O: 4-pin terminal block.
e.
Audio I/O: 4-pin terminal block.
Construction: Polycarbonate, RAL 9003.
The indoor IR minidome IP camera system shall have the following electrical specifications:
1.
2.
C.
a.
Voltage:
a.
12 V DC.
b.
24 V AC.
c.
PoE IEEE 802.3af.
Power Consumption:
a.
12 V DC/24 V AC: 12 W (max).
b.
PoE: PD Type 1, Class 0.
The indoor IR minidome IP camera system shall be designed to meet the following
environmental conditions:
1.
Operating Temperature: 14° F (–10° C) to 122° F (50° C).
2.
Storage Temperature: –4° F (–20° C) to 158° F (70° C).
3.
Relative Humidity: 10% to 85%, non-condensing.
28 23 29-7
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
2.5
Guide Specifications in CSI Format
800-16134 Rev A
MANUFACTURER SUPPORT
A.
Manufacturer shall provide customer service, pre-sales applications assistance, after-sales
technical assistance, access to online technical support, and online training using Web
conferencing.
B.
Manufacturer shall provide 24/7 technical assistance and support by means of a toll-free
telephone number at no extra charge.
PART 3 EXECUTION
3.1
EXAMINATION
A.
3.2
3.3
Examine site conditions prior to installation. Notify Architect and Owner in writing if
unsuitable conditions are encountered. Do not start installation until site conditions are
acceptable.
INSTALLATION
A.
All components of the camera system shall be thoroughly tested before shipping to the
project location.
B.
Camera system shall be installed, programmed, and tested in accordance with
manufacturer’s instructions and recommendations.
1.
Coordinate interfaces with other products with Owner’s representative where
appropriate.
2.
Provide conduit, cable, and wire for complete and reliable installation. Obtain Owner’s
approval for exact location of cameras, boxes, conduit, cable, and wiring runs prior to
installation.
3.
Install conduit, cable, and wire parallel and square with building lines, including raised
floors areas. Do not exceed 40 percent fill in conduits. Gather and tie wires for orderly
installation.
4.
Coordinate with other trades to provide proper sequencing of installation.
FIELD COMMISSIONING AND CERTIFICATION
A.
Field Commissioning: Test bullet camera system as recommended by manufacturer,
including the following:
1.
Conduct complete inspection and testing of equipment, including verification of
operation with connected equipment.
2.
Test devices and demonstrate operational features for Owner’s representative and
authorities having jurisdiction, as applicable.
28 23 29-8
Honeywell 1080p TDN Indoor IR Minidome IP Camera
www.honeywell.com/security
3.4
Guide Specifications in CSI Format
800-16134 Rev A
3.
Correct deficiencies until satisfactory results are obtained.
4.
Submit written copies of test results.
TRAINING
A.
Conduct on-site system administrator and security/surveillance operator training in
accordance with the manufacturer’s instructions and recommendations. Training shall
include, but not be limited to: camera administration, provisioning, configuration, operation,
and diagnostics.
END OF SECTION
28 23 29-9