6 CHANNEL MULTITEK
6 CHANNEL MULTITEK
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
CODE UP THE TRANSMITTER IF USING A DIPSWITCH TYPE TRANSMITTER
POWER UP THE RECEIVER
PRESS PROGRAMMING BUTTON AND KEEP PRESSED UNTIL CHOSEN RELAY CLICKS. (EG.)
RELAY’S 1, 2, 3, 4, 5 OR 6. YOU CAN SEE THE LED LIGHTING UP NEXT TO THE RELAY
RELEASE THE PROGRAMMING BUTTON WHEN YOU HAVE REACHED THE CHOSEN RELAY
TO INSERT YOUR TX CODE INTO.
DECIDE ON A MEMORY LOCATION TO STORE THE TX LOCATION. (LOCATION FROM 1 TO 8)
PRESS THE TX BUTTON WITH ONE HAND AND KEEP BUTTON PRESSED.
PRESS THE PROGRAMME BUTTON ON THE RX WITH THE OTHER HAND AND KEEP IT
PRESSED.
THE LED WILL START TO FLASH. EVERY FLASH IS ONE MEMORY LOCATION
RELEASE PROGRAMME BUTTON WHEN YOU HAVE REACHED THE LOCATION YOU WANT TO
STORE THE TX INTO.
AFTER APROX 2 SECONDS THE RELAY WILL RELEASE AND THE L.E.D. WILL GO OFF TO
CONFIRM THAT THE TRANSMITTER IS STORED IN THE RECEIVER.
NOW RELEASE THE TRANSMITTER BUTTON
REPEAT THE STEPS FROM 3 TO 11 TO PROGRAMME MORE TRANSMITTERS INTO THE
RECEIVER.
LINK IN = LATCH MODE LINK OUT = PULSE MODE
NOTES: IF THE L.E.D. REMAINS ON AFTER RELEASING THE PROGRAMME BUTTON THEN
THE TRANSMITTER WAS NOT STORED. SWITCH OFF THE RX AND START AGAIN.
TO CLEAR ALL MEMORY POWER DOWN THE RECEIVER. PRESS THE PROGRAMME BUTTON
AND POWER UP THE RECEIVER THEN LET GO PROGRAMME BUTTON.
TO FIND OUT WHICH LOCATION IN THE MEMORY A BUTTON IS PROGRAMMED, PRESS THE
PROGRAM BUTTON WHILE PRESSING THE REMOTE BUTTON. THE LED WILL START TO
PULSE. COUNT THE NUMBER TO DETERMINE THE LOCATION IN MEMORY.
ONLY 1 REMOTE BUTTON CAN GO INTO ANY 1 MEMORY LOCATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
CODE UP THE TRANSMITTER IF USING A DIPSWITCH TYPE TRANSMITTER
POWER UP THE RECEIVER
PRESS PROGRAMMING BUTTON AND KEEP PRESSED UNTIL CHOSEN RELAY CLICKS. (EG.)
RELAY’S 1, 2, 3, 4, 5 OR 6. YOU CAN SEE THE LED LIGHTING UP NEXT TO THE RELAY
RELEASE THE PROGRAMMING BUTTON WHEN YOU HAVE REACHED THE CHOSEN RELAY
TO INSERT YOUR TX CODE INTO.
DECIDE ON A MEMORY LOCATION TO STORE THE TX LOCATION. (LOCATION FROM 1 TO 8)
PRESS THE TX BUTTON WITH ONE HAND AND KEEP BUTTON PRESSED.
PRESS THE PROGRAMME BUTTON ON THE RX WITH THE OTHER HAND AND KEEP IT
PRESSED.
THE LED WILL START TO FLASH. EVERY FLASH IS ONE MEMORY LOCATION
RELEASE PROGRAMME BUTTON WHEN YOU HAVE REACHED THE LOCATION YOU WANT TO
STORE THE TX INTO.
AFTER APROX 2 SECONDS THE RELAY WILL RELEASE AND THE L.E.D. WILL GO OFF TO
CONFIRM THAT THE TRANSMITTER IS STORED IN THE RECEIVER.
NOW RELEASE THE TRANSMITTER BUTTON
REPEAT THE STEPS FROM 3 TO 11 TO PROGRAMME MORE TRANSMITTERS INTO THE
RECEIVER.
LINK IN = LATCH MODE LINK OUT = PULSE MODE
NOTES: IF THE L.E.D. REMAINS ON AFTER RELEASING THE PROGRAMME BUTTON THEN
THE TRANSMITTER WAS NOT STORED. SWITCH OFF THE RX AND START AGAIN.
TO CLEAR ALL MEMORY POWER DOWN THE RECEIVER. PRESS THE PROGRAMME BUTTON
AND POWER UP THE RECEIVER THEN LET GO PROGRAMME BUTTON.
TO FIND OUT WHICH LOCATION IN THE MEMORY A BUTTON IS PROGRAMMED, PRESS THE
PROGRAM BUTTON WHILE PRESSING THE REMOTE BUTTON. THE LED WILL START TO
PULSE. COUNT THE NUMBER TO DETERMINE THE LOCATION IN MEMORY.
ONLY 1 REMOTE BUTTON CAN GO INTO ANY 1 MEMORY LOCATION
6 CHANNEL MULTITEK
6 CHANNEL MULTITEK
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
CODE UP THE TRANSMITTER IF USING A DIPSWITCH TYPE TRANSMITTER
POWER UP THE RECEIVER
PRESS PROGRAMMING BUTTON AND KEEP PRESSED UNTIL CHOSEN RELAY CLICKS. (EG.)
RELAY’S 1, 2, 3, 4, 5 OR 6. YOU CAN SEE THE LED LIGHTING UP NEXT TO THE RELAY
RELEASE THE PROGRAMMING BUTTON WHEN YOU HAVE REACHED THE CHOSEN RELAY
TO INSERT YOUR TX CODE INTO.
DECIDE ON A MEMORY LOCATION TO STORE THE TX LOCATION. (LOCATION FROM 1 TO 8)
PRESS THE TX BUTTON WITH ONE HAND AND KEEP BUTTON PRESSED.
PRESS THE PROGRAMME BUTTON ON THE RX WITH THE OTHER HAND AND KEEP IT
PRESSED.
THE LED WILL START TO FLASH. EVERY FLASH IS ONE MEMORY LOCATION
RELEASE PROGRAMME BUTTON WHEN YOU HAVE REACHED THE LOCATION YOU WANT TO
STORE THE TX INTO.
AFTER APROX 2 SECONDS THE RELAY WILL RELEASE AND THE L.E.D. WILL GO OFF TO
CONFIRM THAT THE TRANSMITTER IS STORED IN THE RECEIVER.
NOW RELEASE THE TRANSMITTER BUTTON
REPEAT THE STEPS FROM 3 TO 11 TO PROGRAMME MORE TRANSMITTERS INTO THE
RECEIVER.
LINK IN = LATCH MODE LINK OUT = PULSE MODE
NOTES: IF THE L.E.D. REMAINS ON AFTER RELEASING THE PROGRAMME BUTTON THEN
THE TRANSMITTER WAS NOT STORED. SWITCH OFF THE RX AND START AGAIN.
TO CLEAR ALL MEMORY POWER DOWN THE RECEIVER. PRESS THE PROGRAMME BUTTON
AND POWER UP THE RECEIVER THEN LET GO PROGRAMME BUTTON.
TO FIND OUT WHICH LOCATION IN THE MEMORY A BUTTON IS PROGRAMMED, PRESS THE
PROGRAM BUTTON WHILE PRESSING THE REMOTE BUTTON. THE LED WILL START TO
PULSE. COUNT THE NUMBER TO DETERMINE THE LOCATION IN MEMORY.
ONLY 1 REMOTE BUTTON CAN GO INTO ANY 1 MEMORY LOCATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
CODE UP THE TRANSMITTER IF USING A DIPSWITCH TYPE TRANSMITTER
POWER UP THE RECEIVER
PRESS PROGRAMMING BUTTON AND KEEP PRESSED UNTIL CHOSEN RELAY CLICKS. (EG.)
RELAY’S 1, 2, 3, 4, 5 OR 6. YOU CAN SEE THE LED LIGHTING UP NEXT TO THE RELAY
RELEASE THE PROGRAMMING BUTTON WHEN YOU HAVE REACHED THE CHOSEN RELAY
TO INSERT YOUR TX CODE INTO.
DECIDE ON A MEMORY LOCATION TO STORE THE TX LOCATION. (LOCATION FROM 1 TO 8)
PRESS THE TX BUTTON WITH ONE HAND AND KEEP BUTTON PRESSED.
PRESS THE PROGRAMME BUTTON ON THE RX WITH THE OTHER HAND AND KEEP IT
PRESSED.
THE LED WILL START TO FLASH. EVERY FLASH IS ONE MEMORY LOCATION
RELEASE PROGRAMME BUTTON WHEN YOU HAVE REACHED THE LOCATION YOU WANT TO
STORE THE TX INTO.
AFTER APROX 2 SECONDS THE RELAY WILL RELEASE AND THE L.E.D. WILL GO OFF TO
CONFIRM THAT THE TRANSMITTER IS STORED IN THE RECEIVER.
NOW RELEASE THE TRANSMITTER BUTTON
REPEAT THE STEPS FROM 3 TO 11 TO PROGRAMME MORE TRANSMITTERS INTO THE
RECEIVER.
LINK IN = LATCH MODE LINK OUT = PULSE MODE
NOTES: IF THE L.E.D. REMAINS ON AFTER RELEASING THE PROGRAMME BUTTON THEN
THE TRANSMITTER WAS NOT STORED. SWITCH OFF THE RX AND START AGAIN.
TO CLEAR ALL MEMORY POWER DOWN THE RECEIVER. PRESS THE PROGRAMME BUTTON
AND POWER UP THE RECEIVER THEN LET GO PROGRAMME BUTTON.
TO FIND OUT WHICH LOCATION IN THE MEMORY A BUTTON IS PROGRAMMED, PRESS THE
PROGRAM BUTTON WHILE PRESSING THE REMOTE BUTTON. THE LED WILL START TO
PULSE. COUNT THE NUMBER TO DETERMINE THE LOCATION IN MEMORY.
ONLY 1 REMOTE BUTTON CAN GO INTO ANY 1 MEMORY LOCATION