DEP Division of Recreation and Parks Uniform Specifications
5.1.1: SKIRT, WOMEN
FABRIC:
100% POLYESTER Comfort-Fiber
COLOR:
Spruce Green, Shade #8772
STYLE:
“A” line, or Department approved equivalent. Adjustable waistband with button
closure, Two inset pockets.
WAISTBAND:
Double self goods, one pierce approximately 1” wide with a stretch Ban-rol, or
equivalent, interlining. Front end to be finished with an approximate 2” extension
with pointed edge, and with an approximate ¾” horizontal buttonhole center on
end of extension. Two (2) 22 Ligne Polymer, or equivalent, matching buttons sewn
on inside of front of waistband approximately 2 ½” from edge of waistband.
POCKETS:
One Pocket on each side of skirt with and opening off each side seam
approximately 7” long. Pockets to be approximately 12” long and 6 ½” wide and
set into the waistband seam at top. Pocket to be made of self fabric and stitched to
side seam approximately 2” down to side seam approximately 2” below pocket
opening.
SEWING:
Side seams and pocket to be SSA-1 stitch type, 301 standard, 8-10 stitches per
inch. Edges and seams serged. Hem blind stitched.
5.1.2: TROUSERS, DRESS STYLE FOR MEN
COLOR:
SPRUCE
FABRIC:
75% Dacron Polyester, 25% Wool , Gabardine weave-Mechanical stretch 10%
Breaking Strength: 125 Lbs. In the Warp, 80 Lbs. In the Filling. Weight 11.0011.50 Oz. per linear yard. Construction: 77 ends per inch, 56 picks per inch.
Fiber Length: Wool equals 3-3.5 inches average minimum, Polyester equals 3
inches minimum
Dye Procedure: Piece Dyed.
STYLE:
The style shall conform to modern updated contour cut men’s uniform trousers.
Plain front, 2 front and 2 back pockets. Front pockets are quarter top style with a
minimum of 5" opening. The front pockets will have separate handset inside facing
to give four-ply strength at the entry of the pockets. The front pockets will be hung
to the side seam of the trousers and locked with a bar-tack at the top and bottom
of the pocket opening. The two back pockets will have a Reece piped entry. They
will have a minimum opening of 5". The left back pocket will have a tab to button
closure. They will be bartacked on right and left side for extra strength. Front and
back pockets are to be stitched, turned and topstitched.
106764702
Page 1 of 36
DEP Division of Recreation and Parks Uniform Specifications
BELT LOOPS:
All belt loops are to be lined and of double thickness butted on reverse side and
blind stitched. They shall be a minimum of 5/8" wide by 2" long and are to be sewn
into the waistband seam at top and bottom.
WAISTBAND:
Outside waistband is to be a minimum of 2” wide (self-material). It will be sewn to
the waistband lining at top and waistband curtain is then blind stitched at the
bottom.
WAISTBAND CONSTRUCTION:
Right fly lining and crotch piece extension lined with same material as pocketing.
(To be one piece and sewn down flat). There is to be continuous French fly
extension at the end of the French fly that will attach to button that is sewn on left
side of waistband lining. Left fly is to be lined and corded.
INNER WAISTBAND:
Inner waistband to be Comfort in Action IV with XI.91 interlining. Inner waistband
to be composed in two parts, a 2-1/2” wide two-zone inner waistband and a 1”
wide interlining of elastic. The 2-1/2” wide inner waistband shall be composed of a
4% nylon/ 86% Polyester/ 10% Spandex. It will have 45% manual elongation and
a two-zone construction. The upper zone is stiff to give body to upper waistband
portion and help prevent waistband rollover and ribbed to help hold shirttail in.
The lower part is soft to stretch around the hips, supporting the slack. The 1” wide
stiff elastic will be an interlining to form the cap of the trousers and help prevent
waistband rollover. This elastic shall be composed of 5% Nylon Monofilament /
84% Polyester / 11% Spandex with a manual elongation of 35% (+ or – 10%).
Waistband is blindstitched, not topstitched to assure banding stretch. Bottom
portion is specially beamed and warped in a diagonal twill portion of band,
approximately ¼” high letters (CIA III or IV), with a 4.75” separation between each
identification repeat.
ZIPPER & CLOSURE:
Talon (Gripper-Zipper) #42 Brass or equivalent will also have metal bottom stop,
permanent press treated tape, hook-flex steel waistband closure.
STITCHING, PRESSING AND FINISHING:
The trousers must be stitched with matching thread and all stitching must be 10-11
stitches per inch. The trousers must be neatly pressed on hot head presses and
properly shaped. Outseams and inseams must be pressed open to maintain a
neat and professional appearance. The trousers must be cleaned and finished to
eliminate loose threads. There must be a Texpak clip attached to the top fly of the
finished trousers to insure shape retention during shipping.
POCKETING:
106764702
All pocketing will be made of a polyester/cotton blend permanent dress drill with
an approximate content of 50% polyester / 50% cotton in the spun warp- 100%
texturized polyester in the filling; for a total content of 70% polyester / 30% cotton.
Pocketing will harmonize with color of trousers and waistband. Pocketing shall test
to a minimum abrasion of 225 cycles per ASTM D3886. (Inflated Diaphragm) for
Page 2 of 36
DEP Division of Recreation and Parks Uniform Specifications
the uncoated area; Bottom of front pockets, (aprox. 2-1/2"), shall be Dura Ruff
coated. Area shall test to a minimum abrasion of 1100 cycles before initial rupture.
This shall substantially increase pocket strength over reinforced pockets without
the unsightly ridges of double pockets.
LABELING:
All trousers will be finished with a woven (not printed) label, permanently affixed. It
will include the correct fiber content of the fabric and identification of brand as well
as garment care instructions.
CREASING:
Front & Back Fashion Set permanent creases. Fashion Set is a special process
for permanent front and back creases, formed by an invisible resin treatment. It is
bonded to the inside of the trousers, insuring clean, sharp, straight creases.
Fashion Set is not a baked-in process that can burn or damage cloth fibers.
CROTCH LINING:
Back panels to have crotch liners. Triangular dimensions of crotch liners are to be
approximately 3-1/2” x 9”. Crotch lining to be made of black satin 100% Polyester
fabric
CARE INSTRUCTIONS:
Dry-clean or machine-wash warm with like colors. (90 to 100 degrees F.) (32 to 43
degrees C.) Tumble-dry (120 degrees F.) (49 degrees C.) Warm iron if needed.
SIZES:
To be sizes 28,29,30,31,32,33,34,35,36,37,38,40 to 50 (even sizes only) in open
unfinished lengths to be hemmed to individual request.
All measurements are approximate and "based" on size 34. All other sizes are
graded from these measurements according to size.
5.1.3: TROUSERS, DRESS STYLE FOR WOMEN
COLOR:
SPRUCE
FABRIC:
75% Dacron Polyester, 25% Wool , Gabardine weave-Mechanical stretch 10%
Breaking Strength: 125 Lbs. In the Warp, 80 Lbs. In the Filling. Weight 11.0011.50 Oz. per linear yard. Construction: 77 ends per inch, 56 picks per inch.
Fiber length: Wool equals 3-3.5 inches average minimum, Polyester equals 3
inches minimum
Dye Procedure: Piece Dyed.
STYLE:
The style shall conform to modern updated contour cut ladies uniform trousers.
Plain front, 2 front and 2 back pockets. Front pockets are quarter top style with a
minimum of 5" opening. The front pockets will have separate handset inside facing
to give four-ply strength at the entry of the pockets. The front pockets will be hung
to the side seam of the trousers and locked with a bar-tack at the top and bottom
of the pocket opening.
106764702
Page 3 of 36
DEP Division of Recreation and Parks Uniform Specifications
The two back pockets will have a Reece piped entry. They will have a minimum
opening of 5". Front and back pockets are to be stitched, turned and topstitched.
BELT LOOPS:
All belt loops are to be lined and of double thickness butted on reverse side and
blind stitched. They shall be a minimum of 5/8" wide by 2" long and are to be sewn
into the waistband seam at top and bottom.
WAISTBAND:
Outside waistband is to be a minimum of 1 3/4" wide, (self-material). It will be
sewn to the waistband lining at top and waistband curtain is then blind stitched at
bottom.
WAISTBAND CONSTRUCTION:
Right fly lining and crotch piece extension are lined with same material as
pocketing. (To be one piece and sewn down flat). Left fly is to be lined and corded.
INNER WAISTBAND:
Inner waistband to be Comfort in Action IV with XI.91 interlining. Inner waistband
to be composed in two parts, a 2-1/2” wide two-zone inner waistband and a 1”
wide interlining of elastic. The 2-1/2” inner waistband shall be composed of a 4%
nylon/ 86% Polyester/ 10% Spandex. It will have 45% manual elongation and a
two-zone construction. The upper zone is stiff to give body to upper waistband
portion and help prevent waistband rollover and ribbed to help hold shirttail in.
The lower part is soft to stretch around the hips, supporting the slack. The 1” wide
stiff elastic will be an interlining to form the cap of the trousers and help prevent
waistband rollover. This elastic shall be composed of 5% Nylon Monofilament /
84% Polyester / 11% Spandex with a manual elongation of 35% (+ or – 10%).
Waistband is blindstitched, not topstitched to assure banding stretch. Bottom
portion is specially beamed and warped in a diagonal twill portion of band,
approximately ¼” high letters (CIA III or IV), with a 4.75” separation between each
identification repeat.
ZIPPER & CLOSURE:
Talon (Gripper-Zipper) #42 Brass or equivalent will also have metal bottom stop,
permanent press treated tape, hook-flex steel waistband closure.
STITCHING, PRESSING AND FINISHING:
The trousers must be stitched with matching thread and all stitching must be 10-11
stitches per inch. The trousers must be neatly pressed on hot head presses and
properly shaped. Outseams and inseams must be pressed open to maintain a
neat and professional appearance. The trousers must be cleaned and finished to
eliminate loose threads. There must be a Texpak clip attached to the top fly of the
finished trousers to insure shape retention during shipping.
POCKETING:
106764702
All pocketing will be made of a polyester/cotton blend permanent dress drill with
an approximate content of 50% polyester / 50% cotton in the spun warp- 100%
texturized polyester in the filling; for a total content of 70% polyester / 30% cotton.
Pocketing will harmonize with color of trousers and waistband. Pocketing shall test
to a minimum abrasion of 225 cycles per ASTM D3886. (Inflated Diaphragm) for
Page 4 of 36
DEP Division of Recreation and Parks Uniform Specifications
the uncoated area; Bottom of front pockets, (approx. 2-1/2"), shall be Dura Ruff
coated. Area shall test to a minimum abrasion of 1100 cycles before initial rupture.
This shall substantially increase pocket strength over reinforced pockets without
the unsightly ridges of double pockets.
LABELING:
All trousers will be finished with a woven (not printed) label, permanently affixed. It
will include the correct fiber content of the fabric and identification of brand as well
as garment care instructions.
CREASING:
Front & back Fashion Set permanent creases. Fashion Set is a special process for
permanent front and back creases, formed by an invisible resin treatment. It is
bonded to the inside of the trousers, insuring clean, sharp, straight creases.
Fashion Set is not a baked-in process that can burn or damage cloth fibers.
CARE INSTRUCTIONS:
Dry-clean or machine-wash warm with like colors. (90 to 100 degrees F.) (32 to 43
degrees C.)
Tumble-dry (120 degrees F.) (49 degrees C.) Warm iron if needed.
SIZES:
To be sizes 4 to 24 in open unfinished lengths to be hemmed to individual request.
All measurements are approximate and "based" on size 12. All other sizes are
graded from these measurements according to size.
5.1.4: TROUSERS, WORK STYLE FOR MEN/WOMEN
FABRIC:
with a
65% polyester, 35% combed cotton, 8 oz. per square yard, 3 x 1 right hand twill
post-cured finish. Fabric must be treated with “Soil-bar” soil release and wicking
finish, or equivalent process, and have a post-cured finish. All colors must be vat
dyed.
COLOR:
Spruce Green
STYLE:
Shall be made on a uniform pattern with a plain front with 2 quarter top pockets
and 2 back pockets.
POCKETS:
The front pockets shall have a minimum opening of 6” and be a minimum 6” deep
from the bottom of the opening. They are to be stitched, turned and restitched.
The inside front pocket facing shall be a separate piece of self material finishing
no less than 1¼” wide. The back pockets will have a minimum opening of 5” and
be a minimum 5¾” deep. The pocket closure over the left pocket shall be ¾” wide
and blind stitched so that no stitching shall be seen on the outside of the loop. The
front and back pockets shall have two straight bar tacks, one on each side.
106764702
Page 5 of 36
DEP Division of Recreation and Parks Uniform Specifications
POCKETING:
All pocketing shall be made of a polyester/polyester-cotton fabric and the color
shall harmonize with the outer fabric color. All front pocketing shall have a 2½”
Dura Ruff coating. (See above).
WAISTBAND:
The waistband shall be a minimum of 1½” wide and shall be closed with a
crushproof hook and eye, the eye being bar tacked, or other reinforced stitching,
for stability. The waistband curtain a polyester/polyester-cotton fabric with the
color of the fabric to harmonize with the outer fabric. No roll waistband stiffener,
minimum 5/8” in width, shall be sewn into the waistband on the front of the trouser
from side seam to side seam. The trousers are to be made with a continuous
close waistband.
FLY:
The right fly lining will be the same fabric and color as the waistband curtain. The
right fly lining shall be sewn to the left fly below the zipper. A separate French fly
made of the outer fabric shall be sewn to the inside right fly.
BELT LOOPS:
There shall be a minimum of 5 drop belt loops on waist sizes 28,29,30 a minimum
of 7 on all sizes over 30. Each loop is to be a minimum of 5/8” wide and blind
stitched so no stitching shall be seen on the outside of the loop. Except for the
center back loop which shall be tacked on, all loops will be sewn into the rocap
and bar tacked ¼” below the waistband so as to accommodate a 1¾” belt.
ZIPPER:
The trousers shall be closed with a Scovil Guardloc or equivalent brass zipper and
have a brass bottom stop at the base of the zipper chain. A straight bar tack, or
other reinforced stitching, will be sewn through from the outside of the garment to
the inside at the bottom of the fly. It shall be sewn through the zipper tape, the
right and left fly and the right fly lining. The right and left fly shall be joined by an
additional bar tack, or other reinforced stitching, located below the bottom zipper
stop on the inside of the trouser.
SEAMING:
The entire trouser is to be seamed with polyester core or 100% polyester spun
thread. The seat seams shall be stitched with a tandem needle seat seaming
machine. All exposed inside seams of the trousers are to be serged.
FINISHING AND
PRESSING:
All loose threads shall be removed. Trousers must have Lintrak seam retention, or
equivalent process, applied as part of the manufacturing process. No postproduction will be accepted. Trousers must be pressed completely and properly
with the side seam, inseam, and seat seam pressed open.
5.1.5: SHORTS, MEN/WOMEN
SIZE:
28 – 46
COLOR:
Spruce 31163 (mal) & 30133 (female)
FABRIC:
65% Polyester/35% Cotton Twill
Weight 8 oz/yd²
106764702
Page 6 of 36
DEP Division of Recreation and Parks Uniform Specifications
CONSTRUCTION/DETAILS:
WAISTBAND:
Waistband will be constructed of 1-ply self-fabric, folded and finished 1½” wide.
Ends are single needle closed to yield a clean finish. The zipper is double needle
stitch.
BAND CLOSURE: Band closure is by means of one hook & eye centered on the band 1½” from
the finished edge. Center of horizontal buttonhole will be set ¾” in from the folded
edge of band.
BELT LOOPS:
Belt loops measuring ½” wide finished will be bar tacked at top and bottom. Loop
opening measures 1¾”. Belt loops are bar tack set top and bottom.
Loop placement is as follows:
7-loops 3 each side (evenly spaced) one on seat seam
FLY:
Right fly will have a folded extension serged at the side and bottom with the zipper
sandwiched between the extension seam. Folded right fly measures 1¾”. Left fly
will have a set facing with the side serged. Zipper will have bar tacks at bottom of
left fly and at join seam over “J” stitch (2). Zipper lengths are as follows:
Size
28-36
38 – up
Length
7”
9”
FRONT POCKETS: Front pockets are Patch Pocket Style. Pocket is attached to the front and
double needle top stitched. Pockets will have horizontal bar tacks at top and
vertical at side seam of pocket opening.
HIP POCKETS: Pants will have a left and right hip patch pocket. Hip pockets will have a flap style
pocket button closure. Pocket opening measures 5½”; corners are bar tacked.
Both pockets will have a button flap closure. Pocket and pocket flap are double
needle stitched.
FLAPS:
Pockets have flaps with fusible interlining. Flaps are cut two pieces, ¼” double
needle stitched. Pocket flaps are double needle set.
HEM:
Shorts will be single needle lockstitch hemmed and finish ½” wide with fold under.
Inseam will finish at 7”.
TOLERANCES: Allowed for the above measurements are as follows:
MEASUREMENT RANGE
0” – 6”
6” – 12”
12” – 24”
Over – 24”
106764702
Page 7 of 36
TOLERANCES
±⅛”
±¼”
±½”
±¾”
DEP Division of Recreation and Parks Uniform Specifications
LABELING:
Print Label
FINISHING:
Each garment will be trimmed, inspected, and neatly folded.
5.1.6: SHIRT, LONG SLEEVE, DRESS, ZIPPER STYLE FOR MEN
FABRIC:
Milliken, Fabric #7025 or Department approved equivalent. 100% texturized
Dacron polyester (featherweight) gabardine weave. 2 x 1 construction, 7.0 oz. per
linear yard of 4.3 oz (+ or - .25) per square yard. Fast color, guaranteed washable,
with minimum shrinkage. Permanent press, subject to washing care instruction.
Fabric to include VISA finish, a soil release that combines with it color bright
retention and moisture absorbency for maximum comfort.
COLOR:
Light Green (Lagoon) Shade #2534 or Department approved equivalent.
STYLE:
Long sleeve permanent press police shirt with concealed zipper front and
convertible collar, tapered form fit. Collar and sleeve length size to be in 14 – 14¼
thru 20, with sleeve lengths from 32 thru and including 37, as per size charts as
listed below. Stitched-in military creases.
COLLAR:
Convertible style collar - points approximately 3¼’ long; top stitched 3/16” from
edge; die cut with permanent heat tacked collar stays with a two piece yoke 3”
deep. Outside yoke top-stitched. Inside yoke and Banana to have lining.
FRONT:
To have 1½” placket on top center front. Zipper to be sandwiched and to extend
from the second to the sixth buttonhole with the stitch to be concealed under the
center strip. Front to have (7) buttons and buttonholes.
FLAPS:
One piece, die cut and creased to ensure uniformity. Flaps are to measure a
minimum of 5½” wide and be 2½” long at sides, and a minimum of 2¾” long at
center point with deep scallops, with gripper snaps on underside of flap and on
pocket. Snaps are not to be visible on top of the flap. Hand sewn or dressmaker
snaps will not be acceptable. Pencil division through both flaps. Flap to be lined
with 100%/Dacron lining. Flaps to have button sewn on top approximately 5/8”
above points. Flaps to have 1/16” stitched center crease.
POCKETS:
Die cut and creased to ensure uniformity. Two breast pockets with ½” hem; 1½”
box pleats stitched to prevent spreading. Pockets to be a minimum of 5½” deep
and 5¼” wide with mitered corners. Both pockets to have pencil division 1½”. Each
pocket to have 1/16” stitched-in creases.
BADGE
Inside sling type badge holder of self goods approximately 1-1/2” wide to extend
from
joining seam to pocket of left front. Two small buttonholes, approximately 1” apart
with the lower buttonhole approximately 1” above the flap.
SLING:
SLEEVES:
106764702
One piece with top placket a minimum of 1” wide, button placket ½” wide. Plackets
to be a minimum of 4 ½” long from top of cuff with opening approximately 5”. One
Page 8 of 36
DEP Division of Recreation and Parks Uniform Specifications
button and buttonhole on sleeve facings. Each sleeve shall have an elbow
reinforcement extending to top of cuff. The sleeves must be secured to the body
of the shirt by means of a merrow stitch with a safety stitch so as to properly
strengthen the stitch.
CUFFS:
Minimum 2½” wide with ½” hem; and approximate 3/16” top stitching. Double
buttons with corresponding buttonholes, approximately 1” apart, on each cuff.
FINISHED LENGTH SIZES
COLLAR SIZE
14-14 ½
15-15 ½
16-16 ½
17-17 ½
18-18 ½
19 or more
CUFF LENGTH
10”
10-1/2”
11”
11-1/2”
12”
12”
SHOULDER STRAPS
(EPAULETS):
To measure 2” at sleeve head and tapered to approximate 1⅝” at ends which are
pointed approximate 1”. Straps to be stitched to shoulders by single needle
machine forming and X. Length of straps to graduated conforming to size of shirt.
Buttons attached to yokes to match shoulder strap buttonholes.
STITCHED
CREASE:
There shall be one 1/16” stitched-in crease on each front and three 1/16” stitchedin creases on back. Flaps and pockets to have 1/16” stitched-in crease to give
uniform shape and size.
BUTTONS:
Buttons will be first quality pearlized polyester in a matching or coordination color,
to withstand excess wear and laundering. Size will be a minimum 17 ligne and 4
hole style.
ZIPPER:
Nylon separating zipper with nylon coil, matching binder seam, coordinated color
for all components. All molded plastic.
THREAD:
Spun polyester thread to match shirt fabric.
STITCHING:
Sleeving and closing operation-overlock by means of a merrow stitch with a safety
stitch so as to properly strengthen the seam. All stitches must be of the proper
tension and size to avoid puckering after the shirt has been laundered and to give
best durable press performance.
CUTTING:
Collars, band, pockets, shoulder straps and flaps to be die cut to insure uniformity.
106764702
Page 9 of 36
DEP Division of Recreation and Parks Uniform Specifications
PRESSING:
Component parts must be pressed on hothead machines; finished shirts to be
folded and hand pressed, using jet clips.
PACKING:
Shirts to be shipped in poly bags and three shirts to a box with sizes marked on
outside of box at one end.
EMBLEMS:
There is to be and official Division of Recreation and Parks emblem sewn on each
sleeve of the shirt 1” below shoulder seam. Emblems to be furnished by vendor.
Specifications attached.
5.1.7: SHIRT, LONG SLEEVE, DRESS, ZIPPER STYLE FOR WOMEN
FABRIC:
Milliken, fabric #7025 or Department approved equivalent. 100% texturized
Dacron polyester (featherweight) gabardine weave. 2 x 1 construction, 7.0 oz. per
linear yard or 4.3 oz. (+ or - .25) per square yard. Fast color, guaranteed
washable, with a minimum shrinkage. Permanent press, subject to washing care
instructions. Fabric to include VISA finish, a soil release that combines with it color
bright retention and moisture absorbency for maximum comfort.
COLOR:
Light Green (Lagoon) Shade #2534 or Department approved equivalent.
STYLE:
Long sleeve permanent press women’s police style blouse with zipper and collar,
tapered form fit. Stitched-in military creases.
COLLAR:
Convertible type points approximately 3½” long; top stitched 3/16” from edge. Die
cut. Permanent heat tacked collar stays with a two piece yoke a minimum of 2½”
deep. Outside yoke top stitched. Banana and inside yoke to have lining of 100%
satin polyester.
FRONT:
To have 1½” placket on top center front. Zipper to be sandwiched and extended
from third to the fifth buttonhole with stitch to be concealed under the center strip.
Front to have (6) buttons and buttonholes.
FLAPS:
One piece, die cut and creased to insure uniformity. Two flaps a minimum of 4¾”
wide, 1¾” long at sides and a minimum of 2¼” long at the center with deep
scallops, with gripper snap on underside of flap. Hand sewn or dressmaker snaps
will not be acceptable. Pencil division through both flaps. Flap to be lined with
100% Dacron lining. Flaps to have button sewn on top approximately ¼” above
point. Flaps to have 1/16” stitched in center crease.
POCKETS:
Die cut and creased to insure uniformity. Two breast pockets with a minimum of
¾” box pleats stitched to prevent spreading. Approximately 4¾” deep x 4⅝” wide
with mitered corners. Both pockets to have pencil division 1”. Gripper snaps at top
corners to match flaps snaps. Each pocket to have 1/16” stitched-in creases.
BADGE SLING: Inside sling type badge of self goods approximately 1½” wide to extend from
joining seam to pocket of left front. Two small buttonholes, 1” apart with the lower
buttonhole approximately 1” above flap.
106764702
Page 10 of 36
DEP Division of Recreation and Parks Uniform Specifications
SLEEVES:
One piece with top placket 1” wide and under placket ½” wide both of the same
materials as garments. Placket to be approximately 5½” long x 4½” wide with
mitered corners. The sleeves must be secured to the body of the shirt by means of
merrow stitch with a safety stitch so as to properly strengthen stitch.
CUFF:
To measure a minimum of 2½” wide interlined. Button on cuff. To have ⅛” edge
stitched.
SHOULDER STRAPS
(EPAULETS):
To measure approximately 2” at sleeve head and tapered to 1¾” at ends which
are pointed 1”. Straps to be stitched to shoulders by single needle machine
forming an “X”. Length of straps to be graduated conforming to size of blouse.
Buttons attached to yokes to match shoulder strap buttonholes.
STITCHED
CREASE:
There shall be one 1/16” stitched-in crease on each front and three 1/16” stitched
creases on back. Flaps and pockets to have 1/16” stitched-in creases to give
uniform shape and size.
BUTTONS:
Buttons will be first quality pearlized polyester in a matching or coordinating color,
to withstand excess wear and laundering. Size will be a minimum of 17 ligne and 4
hole style.
ZIPPER:
Nylon separating zipper with nylon coil, matching binder seam, coordinated color
for all components. All molded plastic.
THREAD:
Spun polyester thread to match shirt fabric.
STITCHING:
Sleeving and closing operations-overlock by means of a merrow stitch with a
safety stitch so as to properly strengthen the seam. All stitches must be of the
proper tension and size to avoid puckering after the shirt has been laundered and
to give best durable press performance.
CUTTING:
Collars, pockets, shoulder straps and flaps to be die cut to ensure uniformity.
PRESSING:
Component parts must be pressed on hothead machines; finished blouses to be
folded and hand pressed, using jet clips.
PACKING:
Shirts to be shipped in poly bags and three blouses to a box with sizes marked on
outside of box at one end.
EMBLEMS:
There is to be an official Division of Recreation and Parks emblem sewn on each
sleeve of the shirt 1” below the shoulder seam. Emblems to be furnished by
vendor. Specifications attached.
106764702
Page 11 of 36
DEP Division of Recreation and Parks Uniform Specifications
5.1.8: SHIRT, SHORT SLEEVE, DRESS, ZIPPER STYLE FOR MEN
FABRIC:
Milliken, fabric #7025 or Department approved equivalent. 100% texturized
Dacron polyester (featherweight) gabardine weave. 2 x 1 construction 7.0 oz. per
linear yard or 4.3 oz. (+ or -.25) per square yard. Fast color guaranteed washable.
Permanent press, subject to washing care instruction. Fabric to include VISA
finish, a soil release that combines with it color bright retention and moisture
absorbency for maximum comfort. Color shall be rated 4.0 on 20 hour
lightfastness, laundering and against perspiration shade change with a minimum
shrinkage.
COLOR:
Light Green (Lagoon) Shade #2534 or Department approved equivalent.
STYLE:
Short sleeve permanent press police shirt with concealed zipper front and
convertible collar. Collar to be in regular collar sizes 14 thru 20, not small, medium
or large. Tapered form fit. Stitched-in military creases.
COLLAR:
Convertible type points approximately 3½” long, top stitched 3/16” from edge. Die
cut. Permanent heat tacked collar stays with two piece yoke, 3” deep. Outside
yoke top stitched. Banana and inside yoke to have lining of 100% satin polyester.
FRONT:
To have 1½” placket on top center front, zipper to be sandwiched and to extend
from the second to the sixth buttonhole with the stitch to be concealed under the
center strip. Front to have seven buttons and buttonholes. Fronts to be faced on
each underside with no less than 2½” + or –⅛” turned under of shirt material.
FLAPS:
One piece, die cut and creased to ensure uniformity. Two flaps a minimum of 5½”
wide approximately 2½” at sides, snaps or underside of the flap. Hand sewn or
dressmaker snaps will not be acceptable. Pencil division through both flaps. Flap
to be lined with 100% Dacron lining. Flaps to have horizontal buttonhole ⅝” above
point. Flaps to have 1/16” stitched-in center crease.
POCKETS:
Die cut and creased to insure uniformity. Two breast pockets with ¼” hem; 1½”
box pleats, stitched to prevent spreading. Approximately 6” deep by 5⅜” wide with
mitered corners. Both pockets to have pencil division 1½”. Each pocket to have
1/16” stitched-in center crease.
BADGE SLING: Inside sling-type badge patch of self goods approximately 1½” wide to extend from
joining seam to pocket of left front. Two horizontal buttonholes, approximately 1”
apart with the lower buttonhole approximately 1” above flap.
SLEEVES:
One piece 9¾” to 10” in length with ¾” hem. The sleeves must be secured to the
body of the shirt by means of a merrow stitch with a safety stitch so as to properly
strengthen the stitch.
SHOULDER STRAPS
(EPAULETS):
To measure 2” at sleeve head and tapered to approximately 1⅝” at ends which
are to be pointed approximately ⅞”. Straps to be stitched to shoulders by single
106764702
Page 12 of 36
DEP Division of Recreation and Parks Uniform Specifications
needle machine forming an “X”. Length of straps to be graduated conforming to
size of shirt. Buttons attached to yokes to match shoulder straps buttonholes at
pointed ends.
STITCHED
CREASE:
There shall be one 1/16” stitched-in crease on each front and three 1/16” stitchedin creases on back. Flaps and pockets to have 1/16” stitched-in crease to give
uniform shape and size.
BUTTONS:
Buttons will be of first quality pearlized polyester in a matching or coordinating
color to withstand excess wear and laundering. Size will be 17 ligne and 4 hole
style.
ZIPPER:
Nylon separating zipper, with nylon coil, matching binder seam, coordinated color
for all components. All molded plastic zipper.
THREAD:
Spun polyester thread to match shirt fabric.
STITCHING:
Sleeving and closing operation-overlock with safety stitch so as to properly
strengthen the seam. All stitches must be of the proper tension and size to avoid
puckering after the shirt has been laundered and to give best durable press
performance.
CUTTING:
Collars, pockets, flaps and shoulder straps and flaps to be die cut to ensure
uniformity.
PRESSING:
Component parts must be pressed on hot head machines; finished shirts to be
folded and pressed using jet clips.
PACKING:
Shirts to be shipped in poly bags and three shirts to the box with sizes marked on
outside of box at one end.
EMBLEMS:
There is to be an official Division of Recreation and Parks emblem sewn on each
sleeve of the shirt 1” below shoulder seam. Emblems to be furnished by vendor.
Specifications attached.
5.1.9: SHIRT, SHORT SLEEVE, DRESS, ZIPPER STYLE FOR WOMEN
FABRIC:
Milliken, fabric #7025 or Department approved equivalent. 100% texturized
Dacron polyester (featherweight) gabardine weave. 2 x 2 construction, 7.0 oz. per
linear yard or 4.3 oz. (+ or -.25) per square yard. Fast color, guaranteed
washable. Permanent press, subject to washing care instruction. Fabric to include
VISA finish, a soil release that combines with it color bright retention and moisture
absorbency for maximum comfort and minimum shrinkage.
STYLE:
Short sleeve permanent press women’s police style blouse with zipper and collar,
tapered to fit. Stitched-in military creases.
106764702
Page 13 of 36
DEP Division of Recreation and Parks Uniform Specifications
COLOR:
Light Green (Lagoon) Shade #2534 or Department approved equivalent.
COLLAR:
Convertible type points approximately 3½” long, top-stitched 3/16” from edge. Die
cut. Permanent heat tacked collar stays with two piece yoke. Outside yoke top
stitched. Banana and inside yoke to have lining of 100% satin polyester.
FRONT:
To have 1½” placket on top center front, zipper to be sandwiched and to extend
from the third to the fifth buttonhole with the stitch to be concealed under the
center strip. Front to have (6) buttons and buttonholes.
FLAPS:
One piece, die cut and creased to ensure uniformity. Two flaps approximately 5”
wide, 2” long at sides and minimum of 1¼” long at center with deep scallops, with
gripper snaps on underside of the flap. Hand sewn or dressmaker snaps will not
acceptable. Pencil division through both flaps. Flap to be lined with 100% Dacron
lining. Flaps to have button sewn on top approximately ¼” above point. Flaps to
have 1/16” stitched-in center crease.
POCKETS:
Die cut and creased to insure uniformity. Two breast pockets with approximately
1” box pleats stitched to prevent spreading. Approximately 4¾” deep x 4⅝” wide
with mitered corners. Both pockets have pencil division. Gripper snaps at top
corners to match flap snaps. Each pocket to have 1/16” stitched-in creases.
BADGE SLING: Inside sling-type badge patch of self goods approximately 1½” wide to extend from
joining seam to pocket of left front. Two small buttonholes, approximately 1¼”
apart with the lower buttonhole approximately 1” above flap.
SLEEVES:
The short sleeves are to be cut in one piece and are to measure approximately
8¼” long from shoulder and approximately 4” long from underarms. The sleeve
must be secured to the body of the shirt by means of a merrow stitch with a safety
stitch so as to properly strengthen the seam. The hem is to be approximately ¾”
wide and is to be turned under, no raw edges exposed.
BACKS:
Wide double yoke. Yoke to be approximately 2½” wide at center point, 1¼” wide
on each end where joined into sleeve. To be single stitched 1/16”.
SHOULDER STRAPS
(EPAULETS):
To measure 2” at sleeve head and tapered to approximately 1⅝” at ends which
are to be pointed approximately ⅞”. Straps to be stitched to shoulders by single
needle machine forming to size of blouse. Buttons attached to yokes to match
shoulder strap buttonholes at pointed ends.
STITCHED
CREASE:
106764702
There shall be one 1/16” stitched-in crease on each front and three 1/16” stitchedin creases on back. Flap and pockets to have 1/16” stitched-in crease to give
uniform shape and size.
Page 14 of 36
DEP Division of Recreation and Parks Uniform Specifications
BUTTONS:
Buttons will be of first quality pearlized polyester in a matching or coordinating
color to withstand excess wear and laundering. Size will be 19 ligne and 4 hole
style.
ZIPPER:
Nylon separating zipper with nylon coil, matching binder seam, coordinated color
for all components. All molded plastic.
THREAD:
Spun polyester thread to match shirt color with sizes marked on outside of box at
one end.
STITCHING:
Sleeving and closing operation-overlock with safety stitch.
CUTTING:
Collars, pockets, shoulder straps and flaps to be die cut to ensure uniformity
PRESSING:
Component parts must be pressed on hot head machines; finished shirt to be
folded and pressed using jet clips.
PACKING:
Shirts to be shipped in poly bags and three shirts to a box with sizes marked on
outside of box at one end.
EMBLEMS:
There is to be an official Division of Recreation and Parks emblem sewn on each
sleeve of the shirt 1” below shoulder seam. Emblems to be furnished by vendor.
Specifications attached.
5.1.10: SHIRT, SHORT SLEEVE, WORK FOR MEN
DESCRIPTION: Male S/S Public Safety Shirt
SIZES:
14½ - 22½
COLOR:
Greentone w/Spruce Shoulder Straps
FABRIC:
65% Polyester/35% Cotton
CONSTRUCTIONS/DETAILS:
COLLAR:
Convertible collar is cut two pieces and will have Harodite woven interlining and
collar stays. Collar points have 2¼” long collar stays. Collar stays will be placed in
the front edge of the collar and stitched through and through. Collar is single
needle set and closed to yield a clean finish. Collar is top stitched. Inside collar will
have a self fabric (mock band) reinforcement single needle edge stitch set the
inside.
LANYARD WHISTLE SUPPORTS/EPAULETS:
Shirt has shoulder epaulets with non-woven fusible interlining. Epaulets are
pressed, edge stitched and set into sleeve seams and partly stitched to the
garment by means of crisscross diagonal box stitching 1½” onto the shirt. Finished
epaulets measure 2” wide at armhole seam and taper to 1½” wide at the point.
106764702
Page 15 of 36
DEP Division of Recreation and Parks Uniform Specifications
Note; point of the epaulet will finish ½” from the collar seam. Ends are formed to a
point and will have a buttonhole closure with a Ligne 19 button set on the
shoulder. Button is stitched at the edge of a cut buttonhole eyelet, which allows
passage of Lanyard/whistle cord to the whistle supports. Lanyard supports are
sewn into the collar seam and to shoulder seam of shirt. Support is 1” wide selffabric.
BADGE SLING: Shirt will have a 1½” wide self-fabric badge sling. Sling is single needle set to the
pocket, through the eyelets, and set into the shoulder seam. Badge sling is folded
and merrowed on one side.
EYELETS:
Shirt will have two horizontal eyelets centered on the left breast, over the stitched
creasing and positioned so that the lower eyelet is 1¼” above the pocket flap and
1¼” apart.
POCKETS:
Shirt will have two (2) breast pockets with flaps and velcro closures. Pocket has a
center box pleat. Box pleat is 1½” wide. Stitched creasing down the center of the
box pleat. Pocket is double needle set with mitered corners. Both left and right
pockets and flaps will have a 1½” wide pencil slot running top to bottom. Pocket
hem is single needle lockstitch hemmed and finishes ¾” wide with fold under.
Finished pocket meaures 6” wide by 5¾” deep. Top corners of pocket and pencil
stitch are bar tacked.
FLAPS:
Standard men’s die cut pocket flaps are scalloped and will have non-woven fusible
interlining on bottom side of flap, with double needle stitching around the edges.
Flap is double needle stitched to the shirt. Both left and right pockets and flaps will
have an 1½” wide pencil slot running top to bottom. Flap will have one (1) Ligne 19
button, centered and set ½” from scallop edge (button has no closure). Both left
and right pocket flaps will have a (cut) buttonhole eyelet sewn beneath the mock
button closure, to permit feeding of the lanyard cord and whistle. Finished pocket
flaps will measure 2¾” on each end and 2⅞” at the center point. Stitched creasing
runs along center of flap and aligns with pintuck stitch on box pleat (pocket).
VELCRO:
Flaps and pockets effect closure by means of four (4) strips of Velcro. Strips are 1”
long by ½” wide. The hook side of the Velcro is single needle set on the pocket,
and the loop side of the Velcro is single needle set on the under side of the flap.
Velcro on the pocket is set ⅜” below the finished edge of the pocket, and ¼” in
from the finished side of the pocket.
PLACKET/FACINGS:
Both facings will be folded and merrowed. The left front will be folded to create a
1½” wide placket with 250-edgelock interlining. Placket is top stitched on both
sides. Facings on both sides are merrowed on the outside edges.
106764702
Page 16 of 36
DEP Division of Recreation and Parks Uniform Specifications
CREASING:
Shirt will have two (2) rows of stitched creasing on the front of the shirt. Creasing
extends from shoulder seams, through pocket flaps, and pockets to bottom of
shirt.
SLEEVES:
Shirt will have short sleeves. Sleeve hem in single needle lockstitch hemmed and
finishes ¾” wide with fold under. Ends of sleeve seams are bar tacked. Armhole
seams are pressed and double needle topstitched.
YOKE:
Yoke is cut 2-plyt and is clean finished on the inside. Inside yoke is cut of satin
taffeta. Maritn Woven Label is set to the lining only. Back yoke seam is double
needle topstitched.
UNDERARM EYELETS:
Sleeve underarm will have four (4) round 101 (vented) eyelets under the arm.
Eyelets will be placed as follows: one on each side of the sleeve (front/back) 1”
above the armhole seam and one on each side of the body (front/back) 1” below
the armhole seam. All four (4) eyelets will be placed diagonally 1” from the seam
intersection (:+:).
BACK:
Back is cut one (1) piece with three (3) rows of creasing. One row at center back
and one row on each side spaced evenly apart.
CLOSURE:
Front closure is by means of seven (7) Ligne 19 buttons and one (1) separating
zipper. First button is set ½” below the collar seam, second button is spaced 4”
below the collar seam. All remaining buttons are spaced 3½” apart. First
buttonhole is horizontal. All remaining buttonholes are vertical. Note: Only the first,
second and seventh (last) buttons are working buttons. The third, fourth, fifth and
sixth buttons are mock buttons. The shirt will have a concealed 16” black
separating zipper set beneath the front placket. Zipper is single needle lockstitch
set 4” below the collar seam.
HEM:
Bottom hem is single needle lockstitch hemmed ¼” wide, shirt tail hem.
Measurements:
Chest
Across Back
Across Shoulder
Sleeve Outseam
Sleeve Inseam
Collar
Length
14
40½
20½
17
9
6½
14
32¼
14½
42½
21½
17½
9¼
6½
14½
32½
15
44½
22½
18
9½
6½
15
32¾
15½
46½
23½
18½
9¾
6½
15½
33
16
48½
24½
19
10
6½
16
33¼
16½
50½
25½
19½
10¼
6½
16½
33½
17
52½
26½
20
10½
6½
17
33¾
17½
54½
27½
20½
10¾
6½
17½
34
TOLERANCES: Allowed for the above measurements are as follows:
MEASUREMENT RANGE
0” – 6”
6” – 12”
12” – 24”
106764702
Page 17 of 36
TOLERANCES
±⅛”
±¼”
±½”
18½
58½
29½
21½
11¼
6½
18½
34¾
19½
62½
31½
22½
11¾
6½
19½
35
20½
66½
33½
23½
12¼
6½
20½
35½
DEP Division of Recreation and Parks Uniform Specifications
Over – 24”
±¾”
LABELING: White Woven Label
FINISHING: Each garment will be trimmed, inspected, pressed and neatly folded.
5.1.11: SHIRT, SHORT SLEEVE, WORK FOR WOMEN
Description: Female S/S Public Safety Shirt
Color:
Greentone w/Spruce Shoulder Straps
Fabric:
65% Polyester 35% Cotton Poplin
CONSTRUCTION / DETAILS:
Collar:
Convertible collar is cut two pieces, and will have fusible interlining, and collar stays.
Collar stays are single needle lockstitch set to the under side of the collar. Collar is
single needle set and closed to yield a clean finish. Collar is top stitched.
Placket/Facings:
Both facings will be folded and merrowed. The right front will be folded to create a 1½"
wide placket with 250-edgelock interlining. Placket is top stitched on both sides.
Facings on both sides are merrowed on the outside edges.
Pockets:
Shirt will have two (2) breast pockets with flaps, and Velcro closures. Pocket has a
center box pleat. Pintuck stitching runs down center of box pleat. Pleat is 1" wide.
Pocket has mitered corners. Top of pocket is single needle lockstitch hemmed and
finishes ¾" wide with fold under. On the inside of each pocket will be a single needle
dividing stitch 1½" wide to form pencil slot.
Flaps:
Pocket flaps are scalloped and will have fusible interlining on under side of flap, with
clean-finished edges. Flap is double needle stitched to the shirt. Both left and right
pockets and flaps will have a 1½" wide pencil slot running top to bottom. Flap will have
one (1) Ligne 19 button, centered and set ½" from scallop edge (button has no
closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn
beneath the mock button closure, to permit feeding of the lanyard cord. Stitched
creasing runs along center of flap and aligns with stitched crease on box pleat
(pocket). Finished pocket flaps will measure 2- ¼” on each end and at the center point.
Velcro:
Flaps and pockets effect closure by means of four (4) strips of matching Velcro. Two
strips of Velcro (hooks) are located at top of pocket corners, which effect closure with
corresponding Velcro (loops) on inside of pocket flaps. Velcro strips measure 1" x ⅜”.
Length direction is set vertically on pockets. Velcro is placed so that the top is on the
edge of hemmed pocket, and outer edge is ¼" from edge of pocket. Hook side of
Velcro is on pocket; loop side of Velcro is on the pocket flap. Underside of flaps have a
1"x ⅜” piece of Velcro (loop). Velcro on flap underside is placed ¼" from scalloped
edge and ⅜” from sides.
106764702
Page 18 of 36
DEP Division of Recreation and Parks Uniform Specifications
Badge Sling: Shirt has a 1½" wide self-fabric badge support attached to shoulder seam and sewn
into back of pocket. Badge sling is folded and merrowed on one side (Badge sling is
on left side only).
Eyelets:
Shirt has badge eyelets set above left side pocket flap. Eyelets are set horizontally.
Eyelets are centered on stitched crease and are sewn through shirt and badge sling.
Eyelets are located 1¼" above edge of pocket flap and set 1 ¼" apart.
Sleeves:
Shirt will have short sleeves. Sleeve hem in single needle lockstitch hemmed and
finishes ¾” wide with fold under. Ends of sleeve seams are bar tacked. Armhole
seams are pressed and double needle topstitched.
Creasing:
Shirt front will have stitched creasing sewn down both sides of the shirt. Stitched
creasing extends from shoulder seam through pocket flaps, and pockets, to bottom of
the shirt.
Closure:
Front closure is by means of six, (6) Ligne 19 matching Pearl buttons. First button is
set ½" below the collar seam, (on left side) with a horizontal buttonhole. All remaining
buttonholes are vertical. The remaining button on the shirt is spaced 3½" apart.
Back:
Shirt has 2-ply back yoke. Shirt has three (3) rows of stitched creases down back,
extending from the yoke to bottom of shirt. First stitched crease is at center back of
shirt and one on each side of center crease, evenly spaced. Yoke is clean finish set to
the inside. Label is set to the lining (only). Martunique Label.
Lanyard Whistle Supports/Epaulets:
Shirt has shoulder epaulets. Epaulets are set into sleeve seams and partly stitched to
the garment by means of crisscross diagonal stitching. Rest of epaulet is unattached.
Ends are formed to a point and have a buttonhole that effects closure with a Ligne 19
button set on the shoulder. Finished epaulets measure 2” wide at shoulder seam and
taper 1½” wide at the point. Button is stitched at the edge of a cut buttonhole eyelet,
which allows passage of Lanyard/whistle cord, to the whistle supports (one on each
side). Lanyard supports are sewn into the collar seam and to shoulder of shirt.
Support measures 1" wide by 2¼" long.
Hem:
Bottom hem is ¼" single needle lockstitch set.
5.1.12: SHIRT, LONG SLEEVE, WORK FOR MEN
Description:
Male L/S Public Safety Shirt
Sizes:
14 1/2 – 22 ½
Color:
Greentone w/Spruce Shoulders Straps
Fabric:
65% Polyester/35% Cotton
106764702
Page 19 of 36
DEP Division of Recreation and Parks Uniform Specifications
CONSTRUCTION/DETAILS:
Collar:
Banded collar is cut two (2) pieces and will have Harodite woven fusible and collar
stays. Collar points will have 2 ¼” long collar stays. Collar stays will be placed in
the front edge of the collar and stitched through and through (with ¼” topstitching)
Collar is topstitched. Band has 2-ply non-woven fusible interlining, inside collar
band is cut of self material. Band is single needle set and closed. Collar band has
one horizontal buttonhold and one (1) Ligne 19 button.
Placket:
Left side has a 1 ½” wide placket with edgelock interlining. Placket is top stitched
on each side. Right side is hemmed clean finished to the inside of the shirt with a
¾” hem.
Flaps:
STANDARD MEN’S DIE CUT Pocket flaps are scalloped and will have non woven
fusible interlining on bottom side of flap, with double needle stitching around the
edges. Flap is double needle stitched onto the shirt. Both left and right pockets
and flaps will have a 1/ ½” wide pencil slot running top to bottom. Flap will have
on (1) Ligne 19 button, centered and set ½” from scallop edge (button has no
closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn
beneath the mock button closure, to permit feeding of the lanyard cord and
whistle. Finished pocket flaps will measure 2 ¾” on each end and 2 7/8” at the
center point. Stitched creasing runs along center of flap and aligns with stitched
creasing on box pleat (pocket).
Velcro:
Flaps and pockets effect closure by means of four (4) strips of Velcro. Strips are
1” long by ½” wide. The hook side of the Velcro is single needle set on the pocket,
the loop side of the Velcro is single needle set on the under side of the flap.
Velcro on the pocket is set 3/8” below the finished edge of the pocket, and ¼” in
from the finished side of the pocket.
Badge Sling:
Shirt has a 1/ ½” wide self-fabric badge support attached to shoulder seam and
sewn into back of pocket. Badge sling is folded and merrowed on one side
(Badge sling is on left side only).
Eyelets:
Shirt has badge eyelets set above left side pocket flaps. Eyelets are set
horizontally. Eyelets are centered on stitched creasing and are sewn through shirt
and badge sling. Eyelets are located 1/ ¼” above edge of pocket flap and set 1 ¼”
apart. Eyelets measure 3/8” long.
Sleeves:
Shirt will have long sleeves with elbow patch, adjustable cuffs and Hathaway type
placket. Sleeves terminate with 2-ply cuffs. Cuffs have non-woven fusible
interlining. Cuffs are double needle top stitched and there will be two rows of
stitching on the set cuff operation. Cuffs finish 3” wide. Cuff adjustability is by
means of two (2) rows of buttons, with two (2) buttons for each row (4 buttons).
Ligne 19 white buttons. Buttons effect closure with one (1) row of buttonholes. (2
buttons per-row). Button spacing: first row is set ½” from edge. Second row is set
1 ¼” apart. Note: buttons are 1 ¼” apart (vertically). Armhole seams are pressed
and double needle top stitched.
106764702
Page 20 of 36
DEP Division of Recreation and Parks Uniform Specifications
Sleeve Placket: Hathaway type placket. Top side of placket is 2 ¼” wide and single needle bound
set to the shirt. Underside of placket is ½” wide and single needle bound set.
Vent opening is 4 ½”. One buttonhole on topside of placket effects closure with
one Ligne 19 button on placket underside. Button is located 2 ¼” above cuff
seam.
Banjo Pad:
Each sleeve has a “banjo style” elbow patch. Elbow patch has rounded edges,
and is flat at the bottom. Elbow patch is superimposed on sleeve so that the
bottom side (flat side) joins the sleeve placket. Finished elbow patch measure 7”
long. Elbow patch is edge stitch set.
Underarm Eyelets: Sleeve underarm will have four, (4) round 101 (vented) eyelets under the arm.
Eyelets will be placed as follows: one on each side of the sleeve (front/back) 1”
above the armhole seam and one on each side of the body (front/back) 1” below
the armhole seam. All four (4) eyelets will be placed diagonally 1” from the seam
intersection (:+:)
.
Lanyard Whistle Supports/Epaulets:
Shirt has spruce shoulder epaulets with non woven fusible interlining. Epaulets
are pressed, edge stitched and set into sleeve seams and partly stitched to the
garment by means of crisscross diagonal stitching onto the shirt 1 ½”. Finished
epaulets measure 2” wide at the armhole seam and taper 1/ ½” wide at the point,
½” from edge of collar. Ends are formed to a point and have a buttonhole that
effects closure with a Ligne 19 button set on the shoulder. Button is stitched to the
shoulder edge of a cut buttonhole eyelet, which allows passage of Lanyard/whistle
cord, to the whistle supports (one on each side). Self-fabric lanyard supports are
sewn into the collar seam and to shoulder of shirt. Support measures 1” wide by 2
¼” long.
Creasing:
Shirt will have stitched creasing sewn down both sides of the shirt. Stitched
creasing extends from shoulder seam though pocket flaps, and pockets, to bottom
of the shirt.
Closure:
Front closure is by means of seven, (7) Ligne 19 buttons, and one (1) 16”
separating zipper. First button is set on the collar band with a horizontal
buttonhole. All remaining buttonholes are vertical. The second button on the shirt
is spaced 3” below the collar band seam. All remaining buttons are spaced 3
1½”apart. Note: Only the first, second, and seventh (last) buttons, are working
buttons. The third, fourth, fifth, an sixth buttons are mock buttons. The shirt will
have a concealed 16” separating zipper set beneath the front placket. Zipper is
single needle lockstitch set, 4” below the collar seam.
Back:
Shirt has 2-ply back yoke. Shirt has three (3) rows of stitched creasing down
back, extending from the yoke to bottom of shirt. First crease stitch is at center
back of shirt and one on each side of center crease, evenly spaced.
106764702
Page 21 of 36
DEP Division of Recreation and Parks Uniform Specifications
Yoke:
Yoke is clean finish set to the inside; inside yoke is satin taffeta. Woven Comfort
in Action Label is set to the satin taffeta lining (only). Back yoke seam is double
needle topstitched.
Hem:
Bottom hem is single needle lockstitch hemmed and finishes ¼” with fold under.
Sleeve Length:
32/33
34/35
36/37
14 ½
x
x
x
15
x
x
x
15 ½
x
x
x
16
x
x
x
16 ½
x
x
x
17
x
x
x
17 ½
x
x
x
Measurements:
Chest
Across Back
Slv Inseam
Collar
Waist
Sweep
Length
14 ½
42 ½
21 ½
6½
14 ½
40
43 ½
32 ½
15
44 ½
22 ½
6½
15
42
45 ½
32 ¾
15 ½
46 ½
23 ½
6½
15 ½
44
47 ½
33
16
48 ½
24 ½
6½
16
46
49 ½
33 ¼
16 ½*
50 ½
25 ½
6½
16 ½
48
51 ½
33 ½
17
52 ½
26 ½
6½
17
50
53 ½
33 ¾
17 ½
54 ½
27 ½
6½
17 ½
52
55 ½
34
Measurements:
Chest
Across Back
Slv Inseam
Collar
Waist
Sweep
Length
18 ½
58 ½
29 ½
6½
18 ½
56
59 ½
34 ½
Tolerances:
Allowed for the above measurements are as follows:
19 ½
62 ½
31 ½
6½
19 ½
60
63 ½
35
18 ½
x
x
x
19 ½
x
x
x
20 ½
x
x
x
20 ½
66 ½
33 ½
6½
20 ½
64
67 ½
35 ½
MEASUREMENT RANGE
0” - 6”
6” – 12”
12” – 24”
Over – 24”
TOLERANCES
+ 1/8”
+1/4”
+ ½”
+ ¾”
Labeling:
Comfort in Action Black Woven Label w/plain printed label attached at LEFT SIDE
Finishing:
Each garment will be trimmed, inspected, pressed and neatly folded.
Emblems:
Florida Parks Emblems to be sewn on both sleeves
5.1.13: SHIRT, LONG SLEEVE, WORK FOR WOMEN
Description: Ladies L/S Public Safety Shirt
Color:
106764702
Greentone w/Spruce Shoulder Straps
Page 22 of 36
DEP Division of Recreation and Parks Uniform Specifications
Fabric:
65% Polyester 35% Cotton Poplin
CONSTRUCTION / DETAILS:
Collar:
Convertible collar is cut two pieces, and will have fusible interlining, and collar stays.
Collar stays are single needle lockstitch set to the under side of the collar. Collar is
single needle set and closed to yield a clean finish. Collar is top stitched.
Placket/Facings:
Both facings will be folded and merrowed. The right front will be folded to create a 1½"
wide placket with 250-edgelock interlining. Placket is top stitched on both sides.
Facings on both sides are merrowed on the outside edges.
Pockets:
Shirt will have two (2) breast pockets with flaps, and Velcro closures. Pocket has a
center box pleat. Pin tuck stitching runs down center of box pleat. Pleat is 1" wide.
Pocket has mitered corners. Top of pocket is single needle lock stitch hemmed and
finishes ¾" wide with fold under. On the inside of each pocket will be a single needle
dividing stitch 1½" wide to form pencil slot.
Flaps:
Pocket flaps are scalloped and will have fusible interlining on under side of flap, with
clean-finished edges. Flap is double needle stitched to the shirt. Both left and right
pockets and flaps will have a 1½" wide pencil slot running top to bottom. Flap will have
one (1) Ligne 19 button, centered and set ½" from scallop edge (button has no
closure). Both left and right pocket flaps will have a (cut) buttonhole eyelet sewn
beneath the mock button closure, to permit feeding of the lanyard cord. Stitched
creasing runs along center of flap and aligns with stitched crease on box pleat
(pocket). Finished pocket flaps will measure 2- ¼” on each end and at the center point.
Velcro:
Flaps and pockets effect closure by means of four (4) strips of matching Velcro. Two
strips of Velcro (hooks) are located at top of pocket corners, which effect closure with
corresponding Velcro (loops) on inside of pocket flaps. Velcro strips measure 1" x ⅜”.
Length direction is set vertically on pockets. Velcro is placed so that the top is on the
edge of hemmed pocket, and outer edge is ¼" from edge of pocket. Hook side of
Velcro is on pocket; loop side of Velcro is on the pocket flap. Underside of flaps have a
1"x ⅜” piece of Velcro (loop). Velcro on flap underside is placed ¼" from scalloped
edge and ⅜” from sides.
Badge Sling: Shirt has a 1½" wide self-fabric badge support attached to shoulder seam and sewn
into back of pocket. Badge sling is folded and merrowed on one side (Badge sling is
on left side only).
Eyelets:
Shirt has badge eyelets set above left side pocket flap. Eyelets are set horizontally.
Eyelets are centered on stitched crease and are sewn through shirt and badge sling.
Eyelets are located 1¼" above edge of pocket flap and set 1 ¼" apart.
Sleeves:
Shirt will have long sleeves with adjustable cuffs and Hathaway type placket. Sleeves
terminate with 2-ply cuffs. Cuffs have non-woven fusible interlining. Cuffs are ¼" top
stitched and there will be two (2) rows of stitching on the set cuff operation. Cuffs finish
106764702
Page 23 of 36
DEP Division of Recreation and Parks Uniform Specifications
3" wide. Cuff adjustability is by means of two (2) rows of buttons, with two (2) buttons
for each row (4buttons). Ligne 19 buttons. Buttons effect closure with one (1) row of
buttonholes. (2 buttons per-row). Button spacing: first row is set ½" from edge.
Second row is set 1¼" from edge and buttons are 1¼" apart (vertically). Hathaway
type placket. Topside of placket is 2¼" wide and single needle bound set to the shirt.
Underside of placket is ½" wide and single needle bound set. Vent opening is 4½".
One buttonhole on topside of placket effects closure with one Ligne 19 button on
placket underside. Button is located 2¼" from cuff.
Creasing:
Shirtfront will have stitched creasing sewn down both sides of the shirt. Stitched
creasing extends from shoulder seam through pocket flaps, and pockets, to bottom of
the shirt.
Closure:
Front closure is by means of six, (6) Ligne 19 matching Pearl buttons. First button is
set ½" below the collar seam, (on left side) with a horizontal buttonhole. All remaining
buttonholes are vertical. The remaining button on the shirt is spaced 3½" apart.
Back:
Shirt has 2-ply back yoke. Shirt has three (3) rows of stitched creases down back,
extending from the yoke to bottom of shirt. First stitched crease is at center back of
shirt and one on each side of center crease, evenly spaced. Yoke is clean finish set to
the inside. Label is set to the lining (only). Martunique Label.
Lanyard Whistle Supports/Epaulets:
Shirt has shoulder epaulets. Epaulets are set into sleeve seams and partly stitched to
the garment by means of crisscross diagonal stitching. Rest of epaulet is unattached.
Ends are formed to a point and have a buttonhole that effects closure with a Ligne 19
button set on the shoulder. Finished epaulets measure 2” wide at shoulder seam and
taper 1½” wide at the point. Button is stitched at the edge of a cut buttonhole eyelet,
which allows passage of Lanyard/whistle cord, to the whistle supports (one on each
side). Lanyard supports are sewn into the collar seam and to shoulder of shirt.
Support measures 1" wide by 2¼" long.
Hem:
Bottom hem is ¼" single needle lock stitch set.
5.1.14: SHIRT, KNIT
FABRIC:
50% Combed Cotton/50% Polyester with heavyweight pique knit. Color to be
Lagoon Green.
STYLE:
Boxed two button placket with matching buttons, and ribbed knit banded sleeve.
Reinforced shoulder seam.
COLLAR:
Fashion ribbed collar to be matching color in ribbed knit. To include taped
reinforcement at back of neck.
EMBLEM:
Florida Park Service Logo will embroidered on left front of shirt.
106764702
Page 24 of 36
DEP Division of Recreation and Parks Uniform Specifications
5.1.15: SHIRT, LONG SLEEVE, VOLUNTEER, GRAY FOR MEN/WOMEN
FABRIC:
Poplin, 65% Dacron Polyester, 35% Combed Cotton fast color. Sanforized,
average residual shrinkage does not exceed 2%. Precured Permanent Press with
soil release finish. Wash and wear appearance with a minimum shrinkage.
COLOR:
Gray, Shade #90810/11 or Department approved equivalent.
STYLE:
Collar attached uniform shirt.
FRONT:
To have approximate 1½” placket on top center front. Front to have seven buttons
and buttonholes. Fronts to be faced on each underside with no less than 2½” +/⅛” turn under of shirt material.
BUTTONS:
Minimum of 17 Ligne Pearlized Polyester buttons, matching shade of shirt.
Buttonholes must be opened for those that are to be fastened.
FLAPS:
Two scalloped flaps approximately 5½” wide, 2½” at sides, and 2¾” at center, die
cut and creased to ensure uniformity of shape and size, lined with 100% Dacron
interlining. 1” opening through both flaps adjacent to center plait for pencils. Each
flap to have Velcro closure at both corners. Button sewn on top of flap.
POCKETS:
Two breast pockets with approximately 1½ ” box pleats stitched to prevent
spreading approximately 5¾” long by approximately 5 3/16” wide with mitered
corners – pockets to be die cut and die creased in ensure uniformity of shape and
size. Both pockets to have pencil division. Velcro closure on both pockets to match
Velcro on flaps.
SLEEVES:
One piece with top placket one inch wide and under placket ½” wide both of same
material as garment. Plackets to be approximately 5” long from top of cuff.
Sleeves should be tapered in proportion to finished measurements given below.
Button and buttonhole on placket.
ELBOW REINFORCEMENT:
Patches not less than 5½” x 4¾” with all four corners mitered to be set over sleeve placket on both
sleeves. Patches to be die cut
and die creased to ensure uniformity.
CUFF:
To measure approximately 3” wide interlined. Double button cuffs approximately 1”
apart between holes. To have approximately ⅛” edge stitch.
FINISHED LENGTH SIZES
COLLAR SIZE
14½ to 15
15½ to 16
16½ to 17
17½ to 18
106764702
CUFF LENGTH
10”
10½
11”
11½”
Page 25 of 36
DEP Division of Recreation and Parks Uniform Specifications
18½ or more
12”
COLLARS AND
BANDS:
Pressed stand-up collar and band. Collar points approximately 3⅜ long. Back of
collar approximately 1¾” wide, collar stand approximately 1¼”wide. Collar to be
die cut and die creased, band to be die cut. Permanent heat tacked collar stays.
Collar shall be lined, with 100% Dacron interlining. To have 3/16” edge stitch.
With double yoke approximately 1¾” from collar seam.
BACKS:
SHOULDER
(EPAULETS):
Straps to measure 2” at sleeve head tapered to approximately 1⅝” at ends which
are to be pointed ⅞”. Point of straps to be approximately ½” from collar. Straps to
be sewn down at the sleeve with single stitching. Straps to be stitched to shoulder
with single needle machine forming an “X”. Buttons attached to shoulder to match
strap buttonhole. Length of straps to be graduated to size of shirt.
STITCHING:
Shirts shall have merrow stitching for sleeving operation and for closing operation.
Balance of shirt to be single lock stitched.
CREASING:
Wherever creasing is specified, the operation is to be performed on a heat
machine using dies for absolute uniformity.
LENGTH:
Minimum length for all sizes to be approximately 32½” measured from collar seam
to bottom of tail center of back.
CUTTING:
Collars, band, pockets, flaps, elbows reinforcements and cuffs to be die cut to
ensure absolute uniformity.
FIT:
To be tailored to chest and waist measurements of wearing personnel, and must
be available in 2 body sizes for each neck size.
MEASUREMENTS:
All of the above measurements are approximately, +/- ⅛”, and are from a size
14½, long sleeve shirt.
5.1.16: SHIRT, SHORT SLEEVE, VOLUNTEER, GRAY FOR MEN/WOMEN
FABRIC:
Poplin, 65% Dacron Polyester, 35% Combed Cotton fast color. Sanforized,
average residual shrinkage does not exceed 2%. Precured Permanent Press with
soil release finish. Wash and wear appearance.
COLOR:
Gray, Shade #90810/11 or Department approved equivalent.
STYLE:
Convertible collar uniform shirt, in regular collar sizes 14 through 18, not small,
medium, or large.
106764702
Page 26 of 36
DEP Division of Recreation and Parks Uniform Specifications
FRONT:
To have 1½” placket on top center front. Front to have seven buttons and
buttonholes. Fronts to be faced on each underside with no less than 2½” +/- ⅛”
turn under of shirt material.
BUTTONS:
Minimum of 17 Ligne Pearlized Polyester buttons, matching shade of shirt.
Buttonholes must be opened for those that are to be fastened.
FLAPS:
Two scalloped flaps approximately 5½” wide, 2½” at side and approximately 2¾”
at center, die cut and creased to ensure uniformity of shape and size, lined with
100% Dacron interlining. 1” openings through both flaps adjacent to center plait for
pencils. Each flap to have Velcro closure at both corners. Button sewn on top of
flap.
POCKETS:
Two pockets with approximately 1½” box pleats stitched to prevent spreading
approximately 5¾” long by approximately 5 3/16” wide with mitered corner pockets
to be die cut and die creased to ensure uniformity of shape and size. Both pockets
to have pencil division. Velcro closure on both pockets to match Velcro on flaps.
SLEEVES:
One piece measuring no less than 9½” on upper portion and no less than 6½” on
lower portion, on size 14½; graduated according to size.
COLLAR:
Convertible type with points 3½”. Single stitched approximately 3/16” lined with
100% Dacron interlining. Collar to be die cut and die creased. Collars to have
permanently heat tacked stays and to be made in regular collar sizes.
BACKS:
With double yoke approximately 1¾” from collar seam.
SHOULDER
(EPAULETS):
Straps to measure 2” at sleeve head tapered to approximately 1⅝” at ends which
are to be pointed ⅞”. Point of straps to be approximately ½” from collar. Straps to
be sewn down at the sleeve with single needle machine forming an “X”. Buttons
attached to shoulder to match strap buttonhole. Length of straps to be graduated
to size of shirt.
STITCHING:
Shirts shall have merrow stitching for sleeving operation and for closing operation.
Balance of shirt to be single lock-stitched.
CREASING:
Wherever creasing is specified, the operation is to be performed on a heat
machine using dies for absolute uniformity.
LENGTH:
Minimum length for all sizes to be approximately 32½” measured from collar seam
to bottom of tail center of back.
CUTTING:
Collars and pockets and flaps to be die cut to ensure absolute uniformity.
FIT:
To be tailored to chest and waist measurements of wearing personnel, and must
be available in 2 body sizes for each neck size.
106764702
Page 27 of 36
DEP Division of Recreation and Parks Uniform Specifications
MEASUREMENTS:
All of the above measurements are approximate, plus or minus 1/8”, and are from
a size 14 ½, short sleeve shirt.
5.1.17: TEE SHIRT, VOLUNTEER
Hanes cotton “Beefy-Tee” tee shirt, or Department approved equivalent. Ash in
color, crew neck with pocket on left front with Volunteer plus Florida Park Service
Logo silk screened in black on pocket.
5.2.1: JACKET, DRESS/WORK
COLOR:
Spruce Green
SHELL FABRIC: The Shell fabric shall be Tactel - 100% two ply Nylon with a water repellent finish.
PERMANENT SHELL LINING:
Cloth type: 100% Nylon Tafetta, 70 Denier wrap and fill, color black, coating –
WeatherTech Waterproof/Breathable.
All lining joining seams shall be safety stitched and then sealed with 1” heat sealed
tape to prevent leakage. The tape shall be applied by hot air method. The tape shall
not be affected by weather, temperature or storage. All stitching through the lining
shall be sealed with waterproof tape. The lining shall extend through the top collar of
the shell garment to form a waterproof barrier. There shall be 2 female snaps at the
seam joining point and opposite, approximately 2 ¼” from the sleeve bottom, to
attach to the removable liner. There shall be an inside storage pocket of shell
material on the left side of the lining measuring approximately 8 ½” deep by 7” wide.
The pocket shall be taped at all points where the pocket is attached to prevent
leakage.
ZIP OUT LINER: The lining fabric shall be made of Thinsulate by 3M, 100% nylon taffeta from
Dupont, 104 x 86 thread count per square inch quilted 200 gram/body with 100/gram
sleeves. Backing shall be 100% nylon taffeta from Dupont, 104 x 86 thread count
per square inch.
The liner shall have long sleeves and knit wristlets with tab and loop to accept
anchor buttons or anchor strap. The entire body shall be bound with 1 9/16" nylon
bias binding. The side seams, shoulder seams and sleeve seams shall be joined
with a serge-sew safety stitch machine. The armhole will have a knit insert to allow
freedom of movement. The pocket shall be 1 lower right inside patch pocket. The
pocket shall be bound with 1 9/16" nylon bias binding and shall be attached with a
single needle machine.
There shall be an interlining molded nylon zipper, center marked, and
interchangeable attached to the liner. The zipper shall be of sufficient length to be
satisfactorily attached to the facing of the jacket.
106764702
Page 28 of 36
DEP Division of Recreation and Parks Uniform Specifications
DESIGN:
The jacket shall be a full cut, waist length model with a double outside fly of self
goods covering a 2 way zipper front, Thinsulate zip-in, zip-out liner, shirred
waistband, and zippered side vents. Coat construction shall be used throughout with
body and sleeves being fully lined.
BODY DETAIL:
The pocket shall be plain with patch pockets, flaps and badge tab. The inside
facings shall be made of outer shell fabric and are to be sewn on top of the nylon
lining that extends to the front edge of the jacket. There shall be a bi-swing back
designed with the articulated gusset for full freedom of movement.
There is to be a separate 2" shirred waistband with heavy duty elastic. The entire
waistband is to be shirred with the exception of an area 5 1/2" on either side of the
front opening. There shall be side zipper entry on either side, approximately 11" in
length and secured by a nylon zipper and snap closure. The shoulders shall have
pads. A self goods reinforcement strip, approximately 3", shall be sewn on the side
of the jacket joined at the top of the waistband and extending from side to side.
There shall be a 1 1/2" wide fly from the bottom of the collar to the bottom of the
waistband. There shall be a double fly of self goods covering the front zipper.
INSIDE DETAIL: On the left side of the coat, there shall be a gun pocket installed on the permanent
lining of the coat to accept a small frame handgun. The gun pocket shall have a
minimum opening of 4 1/2" and be a minimum of 6" deep. The gun pocket shall be
furnished with a strap and snap closing. Bar tacks shall reinforce the opening.
There shall be 2 cut-in pocket on the left and right sides measuring approximately 5
1/4" wide and 6" deep. There shall be a strap and snap on the lining of each sleeve
end for attaching the zip-in liner.
SLEEVES:
The sleeves shall be one piece set in with a single needle machine. The bottom of
the sleeve shall have a heavy duty elastic closure with a triple snap adjustment.
POCKETS:
There shall be two patch pockets with box pleats, finishing approximately 6 1/4" wide
and 7 1/2" deep. Flaps shall be scalloped and self lined. They shall close with
velcro on the side points and with a centered buttonhole. The pockets shall be selflined with an opening of approximately 5 1/2" on the side. The left patch pocket is to
have a pencil opening at the top of the flap. Both the pockets and the flaps are to be
bartacked.
COLLAR:
The stand-up collar shall be made using self material. It shall be interlined with
Pellon.
BACK:
The back band is constructed with heavy-duty elastic inserted between the folded
fabric at the sides. The elastic is stretched and stitched with four threads. A 3 ¾”
x 1.5” tab of two plies of shell material with #24 female snap (enameled cap) is
provided to close the zipper vent when worn open. A brass oxidized male snap is
provided on the elasticized back to fold the tab back when not in use.
106764702
Page 29 of 36
DEP Division of Recreation and Parks Uniform Specifications
EPAULETS:
The epaulets shall be made of self goods. They shall be sewn into the sleeve head
seam, "X" stitched, and tacked to the jacket at the neck.
BADGE TAB:
The badge tab shall be made of the outer fabric, 1" wide with 2 metal eyelets
spaced 3/4" vertically apart. It shall be centered 2 1/2" above the left pocket flap.
ZIPPER:
There shall be a YKK #5, 2 way molded nylon zipper in the front and 11" nylon
zipper on each side vent.
BUTTONS AND SNAPS:
The pocket flaps and epaulets shall be secured with 24 ligne metal buttons. Flaps
and epaulets shall close with 24 ligne metal buttons. Front fly and side zipper tabs
shall be secured by high impact, non-reflective, non-glare, scratch resistant snaps.
THREAD:
All sewing is to be done with polyester core thread or 100% spun polyester thread.
SIZE TAG AND CARE INSTRUCTIONS:
Each jacket shall have a sewn-in woven size label. There shall also be a printed
label with care instructions and each coat marked with Lot number, size, fiber
content and WPL number.
SIZING:
Jackets are to be sized in Regulars XS, S, M, L, XXL, and XXXL. In Longs M, L,
XL and XXL.
EMBLEMS:
There shall be a DEP Parks Emblem attached on each sleeve included in the
cost of each jacket.
5.2.2: WINDBREAKER, NYLON, FLANNEL-LINED
FABRIC:
High grade double strength water repellent 100% nylon permanent press.
COLOR:
Spruce Green and Black
LINING:
Flannel lining (100% polyester)
STYLE:
Long point contemporary collar. Two lower front slant pockets with storm flap tops
designed to keep out wind and rain. Full cut body and length. Matching color snap
front drawstring bottom.
CUFFS:
Wide comfortable elastic cuff.
SLEEVES:
Double reinforced set-in sleeves.
EMBLEM:
Florida Park Service Logo is to be embroidered on left breast of Spruce Green
Jacket and Volunteer – Florida Park Service embroidered in white on left breast of
Black Jacket.
106764702
Page 30 of 36
DEP Division of Recreation and Parks Uniform Specifications
5.3.1: SOCKS, MID-CALF (MEN)
FABRIC:
75% Hi-bulk Acrylic, 20% Nylon, 5% Lycra Spandex
COLOR:
Black
STYLE:
Mid-calf length. Duramax, or equivalent, construction, heel and toe.
CARE
INSTRUCTIONS: Machine wash/dry warm. No bleach.
5.3.2: SOCKS, CREW LENGTH (WOMEN)
FABRIC:
75% Cotton, 25% Stretch Nylon
COLOR:
Black
STYLE:
Fashion crew length
CARE
INSTRUCTIONS: Machine wash/dry warm. No bleach.
5.3.3: SOCKS, MEN/WOMEN, WHITE
FABRIC:
100% cotton or Department approved equivalent
STYLE:
Crew length sock. Reinforced heel and toe.
CARE INSTRUCTIONS:
Machine wash/dry
5.3.4: TIE, CLIP-ON
STYLE:
New metal clip (Redi-Made) tie with pre-formed knot, center crease, permanently
tied on metal frame, main body and hook of steel for added durability.
FABRIC:
100% fine line gabardine texturized woven polyester, 2 ply, approximately 10 ½
oz. per linear yard, 72 x 58 finished count construction, shrinkage allowance
approximately 2% or equal.
COLOR:
Spruce Green or Department approved equivalent. Color shall be rated 4.0 (high)
on 40 hour light-fastness and on wash-fastness and against perspiration shade
change.
5.3.5: TIE, FOUR-IN-HAND, WOVEN POLYESTER GABARDINE
106764702
Page 31 of 36
DEP Division of Recreation and Parks Uniform Specifications
STYLE:
Regular style necktie, four-in-hand, pocket tip ends, long piecing, width at widest
point to be approximately 3½”. Big end lining 24” long cut on bias, small end lining
24” long, cut on straight to eliminate excess stretching of neck band.
FABRIC:
100% fine line gabardine texturized woven polyester, 2 ply, approximately 10½ oz.
per linear yard, 72 x 58 finished count construction, shrinkage allowance
approximately 2% or equal.
COLOR:
Spruce Green or Department approved equivalent.
5.3.6: TIE, WOMEN’S CROSSOVER
STYLE:
Crossover style with adjustable band and matching covered button snap.
FABRIC:
100% fine line gabardine texturized woven polyester, 2 ply, approximately 10½ oz.
per linear yard, 72 x 58 finished count construction, shrinkage allowance
approximately 2% or equal.
COLOR:
Spruce Green or Department approved equivalent.
5.3.7: BASEBALL STYLE CAP, WITH EMBROIDERED LOGO, SUMMER & WINTER
FABRIC:
100% Polyester 2 ply 11/25 oz. per linear yard. Gabardine weave. Gabardine
weave and fabric is mandatory to maintain consistency with uniform. Visa finish.
Spruce Green and Black.
MESH:
(Summer Cap Only) Nylon, Endurlon or equal. Contour fit to conform to front
fabric. Color to be Spruce Green and Black.
DESIGN:
Baseball style five gore construction. Low crown seamless front, double supported
with a sewn in Cotton Osnaburg and a polyester or nylon rigid half stay. The visor
is to be of three piece construction with a minimum six rows of stitching. All gore
seams to be taped to match fabric or black, the color of the mesh. The crown shall
be of a matching color, or black, and an adjustable seven post plastic tab on the
back to allow for full size range adjustment. One size fits all.
VISORBOARD: High density polypropeline extending approximately 3” from the sweatband (+/¼”). Thickness shall be .007 mm minimum.
SWEATBAND:
Finished to 1¼” (+/- 1/16”). Construction of cotton or poly/cotton fabric lined inside
with foam and nonwoven for rigidity and absorption.
SEAMING AND
STITCHING:
A proper seam allowance shall be maintained to prevent raw edges, run offs,
twists, pleats, or open seams. All seams shall have 9-10 stitches per inch. Cutout
at back shall be taped with color to match, or black.
106764702
Page 32 of 36
DEP Division of Recreation and Parks Uniform Specifications
LABEL:
A permanent label shall be attached to the sweatband and state, ONE SIZED
FITS ALL.
AGENCY LOGO: Florida Park Service Logo is to be embroidered on front of the Spruce Green Cap.
Volunteer-Florida Park Service is to be embroidered in white on front of Black
Cap.
5.3.8: EMBLEM, OFFICIAL
To be sewn on each sleeve of jackets and shirts one inch down from the shoulder seam. All threads
are to be fast color, washable and all stitching on outer borders are to be lock-stitched to prevent
raveling. The outer edges to be sewn with washable, colorfast, stitching, and on all outer borders
are to be lock-stitched to prevent raveling. The outer edges to be sewn with six thread merrow
stitches to eliminate raw edges. The emblem is to be approximately 4¾" wide by 3¾" high on fast
color, washable white twill, one piece construction. Emblem to be a one quarter circle design with
spruce green inter and outer borders. Lettering (bold): Top of circle: FLORIDA PARK SERVICE; left
side: Environmental; right side: Protection. Letters ¼" in height to be centered in the space between
the inner and outer borders and to be stitched with spruce green thread. The center space inside the
inner border to be divided into a light blue top representing the sky and a dark blue representing
water. Centered in the space is to be an outline of the State of Florida in sharp raised relief using
rust color thread. The state outline to show Lake Okeechobee, Tampa Bay and the Florida Keys.
The outline is to be overlaid on a stylized sun with sun in raised relief using gold color thread. Two
sable palm trees with curved trunks of rust color thread and spruce green tops rise from the lower
left inner border. In addition to the above patch for all uniformed positions, there will be a top tab
approximately ⅝" wide attached (sewn not acceptable) in one piece with spruce green borders. Top
tab lettering to be approximately ¼" in height of spruce green thread and the lettering. (See attached
drawing for specific details.)
5.3.9: HAT, CAMPAIGN SYTLE
STYLE:
Traditional four dent style. Color to be Tan. NO BADGE EYELET. Imported Milan
Straw. Entire hat to be triple shellacked for extra waterproofing.
CROWN:
Crown is to be 5” high. Each dent is to extend from 2” above bottom of crown to
top of crown forming a flat portion at the top that is approximately 2” wide.
BRIM:
3” double brim, flat, no curl.
BAND:
12 Ligne Mylined Grograin, raw edge ⅞” wide, with side bow. Color to coordinate
with hat color.
GROMMETS:
Two (2) side black metal grommets 11/16” long opening in brim, one on each side,
for hat strap.
STRAP:
Black one piece leather ⅜” wide with non-tarnishable buckle.
SWEATBAND:
Black nylon permanently laminated to polyurethane foam.
106764702
Page 33 of 36
DEP Division of Recreation and Parks Uniform Specifications
SIZES:
6½” through 7¾” in ⅛” increments.
PACKING:
Individually boxed in corrugated containers minimum 125 lb. test.
106764702
Page 34 of 36
DEP Division of Recreation and Parks Uniform Specifications
UNIFORM SIZE CHART
Skirt (Standard Sizes):
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
Trousers, Dress Style and Work Style for Men (Waist Sizes):
28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 40, 42, 44, 46, 48, 50
Trousers, Dress Style and Work Style for Women (Standard Sizes):
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
Shorts, Men
(Waist Sizes): 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50
Shorts, Women
(Sizes): 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
Shirt, Long Sleeve, Dress, Zipper Style and Work Style for Men:
14-14 1/2
32-33
34-35
36-37
15-15 1/2
16-16 1/2
17-17 1/2
18-18 1/2
19-19 1/2
20
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Shirt, Short Sleeve, Dress, Zipper Style and Work Style for Men (Neck Sizes):
14-14 1/2, 15-15 1/2, 16-16 1/2, 17-17 1/2, 18-18 1/2, 19-19 1/2, 20
Shirt, Long and Short Sleeve, Dress, Zipper Style and Work Style for Women (Bust Sizes):
30, 32, 34, 36, 38, 40, 42, 44, 46, 48
Shirt Knit
XS, S, M, L, XL, XXL, XXXL.
TO FIT BOTH MEN AND WOMEN.
Tee Shirt
S, M, L, XL, XXL
106764702
Page 35 of 36
DEP Division of Recreation and Parks Uniform Specifications
Jacket, All-Season: To fit both Men and Women
Size S
Reg. X
Long
M
X
X
L
X
X
XL
X
X
XXL
X
X
Windbreaker, Nylon Flannel-Lined: XS, S, M, L, XL, XXL
Socks, Men: Fit shoe sizes 6 - 12½
Socks, Women: Fit shoe sizes 4½ - 9
Socks, Men/Women: One size fits all
Tie, Clip-on:
To be available in the following sizes:
Prep:
Regular:
Long:
14½"
17"
18½"
ALL UNIFORMS TO BE CUT ON STOCK PATTERN TO FIT ALL SIZES.
106764702
Page 36 of 36