(Project No.)
(Date)
(Project Name)
(Project Location)
ARCHITECT & ENGINEER SPECIFICATIONS
SECTION 28 23 29
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
SSC-CD75P Ruggedized Minidome Color Camera
PART 2 – PRODUCTS
2.01 CCTV CAMERA SPECIFICATIONS
A. GENERAL REQUIREMENTS:
1. The color SSC-CD75P camera shall utilize a high resolution a 1/3-type
Super HAD™ Interline Transfer Type CCD image sensor. The camera
shall produce 540 lines horizontal resolution. The camera shall require a
minimum scene illumination of 0.9 lux at F1.3 or (50 IRE, AGC On, Turbo
On).
2. Video connection for the SSC-CD75P camera shall be via a pigtail with a
“BNC” Connector.
3. The camera shall have AGC gain of 24dB. The AGC shall be dip switch
on/off selectable.
4. The SSC-CD75P shall utilize Digital Signal Processing (DSP) to provide
high stability and reliability.
5. The SSC-CD75P shall have an integral 3.6x (2.8 to 10mm) F1.3 to F3.0,
IR compensated DC auto-iris type vari-focal lens.
6. The camera’s main body shall be constructed of aluminum die-cast, and
the lower clear dome shall be polycarbonate.
7. The SSC-CD75P shall have a ¾” conduit opening on both the bottom and
side of the camera unit. A removable conduit cap shall be used to seal the
unused conduit opening.
8. A secondary video output shall be located on the main camera body, to
allow for easy adjustment of the field of view and focus. The secondary
video output shall be via a phono (RCA) connector.
B. OPTICAL REQUIREMENTS:
1. The SSC-CD75P shall incorporate an integrated, DC type auto-iris, 2.8 to
10mm vari-focal lens.
Maximum aperture shall be F1.3.
2. The minimum object distance shall be 0.3m (0.97ft).
3. A level adjustment potentiometer shall be available to adjust the iris for
optimum exposure.
4. The optical system shall permit the camera to cover a large angle of view
from 100.8° to 27.7° horizontally.
5. The Lens Zoom / Focus lever shall have a locking screw.
C. VIDEO -ELECTRICAL REQUIREMENTS:
1. The SSC-CD75P shall use an input voltage of either 12VDC ±10% or
24VAC ± 10% for power.
2. The power connection shall be by means of a 2-pin mating pressure fit
screw terminals, to connect to an external power supply of 24VAC 50
Hz/60 Hz or 12VDC.
3. The scanning system shall be 625 lines, 50 fields/25 frames, 2:1 interlace.
4. The SSC-CD75P signal system shall be PAL standard.
5. The camera shall employ Auto Tracing White (ATW) balance as well as
ATW PRO modes.
6. The Auto Tracing White (ATW) balance range shall be 2,000 K to 10,000
K, and ATW PRO shall be 2,500 K to 6,500 K. The ATW-Pro balance shall
automatically adjust between the ranges of 2,500 K to 6,000 K.
7. Camera synchronization shall be dipswitch selectable Internal or External
AC (60Hz) line lock, with vertical phase adjustment capability of ± 90°.
8. The camera shall automatically switch to internal sync mode when 12VDC
is applied, regardless of the sync mode setting.
9. The SSC-CD75P composite video output shall be 1.0V peak-to-peak @
75 ohms, sync negative via the pigtail BNC connector.
10. The signal-to-noise ratio shall be more than 50dB (AGC OFF, Weight ON).
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 2
11. Easy camera set-up shall be done by the means of dipswitches as well as
two potentiometers, one to compensate for video level and the other for
Vertical Phase adjustment.
12. The SSC-CD75P shall employ a center-weighted backlight compensation
system, and shall be dipswitch on/off selectable.
13. The SSC-CD75P power consumption shall be 4 watts. With the optional
heater unit installed, the power consumption shall be 16 watts.
D. MECHANICAL REQUIREMENTS:
1. The lens shall have lock-down lever screws for both zoom and focus.
2. The integrated lens (2.8 to 10mm auto iris vari-focal lens)/CCD assembly
shall be mounted on a 3-axis ball-socket mechanism to easily rotate to the
desired field of view. A lock-down screw shall be provided to lock the lens
in place.
3. The camera shall come with a slotted, plastic black insert, installed onto
the main camera section, such that the lens will only be visible when
viewed through that slot.
4. The main body of the camera shall be of aluminum die-cast construction.
5. The lower dome cover shall be made of polycarbonate material.
6. The camera shall be IP66 rated in accordance with the IEC 60529
standard and IK10 rated in accordance with the IEC 62262 standard.
7. The SSC-CD75P shall have a ¾” conduit opening on both the bottom and
side of the camera unit. A removable conduit cap shall be used to seal the
unused conduit opening.
8. The diameter of the lower polycarbonate clear dome shall be
approximately 3 inches.
9. The dome cover shall have a removable safety rubber ring attached to the
main body for safety.
10. The lower dome cover shall be attached to the main body via security
tamper resistant Torx screws.
11. The CCD/Lens body shall be capable of being rotated, and secured via
lock-down screws.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 3
12. Dimensions of the camera shall be 177.5 mm diameter, by 141.5 mm
height.
13. The camera shall weigh approximately 3 pounds 14 ounces (1,750
grams).
E. ENVIRONMENTAL REQUIREMENTS:
1. The operating temperature shall be -4°F to +122°F (-20°C to +50°C). With
the optional heater (YT-HU75) installed, the lower temperature limit shall
be -40°F (-40°C).
2. The operating humidity shall be 20% to 80% (non-condensing).
3. The storage temperature must not be less than -40°F or greater than
140°F (-40°C to +60°C).
4. The storage humidity shall be 20% to 95% (non-condensing).
F. SUPPLIED ACCESSORIES:
1.
2.
3.
4.
5.
Operating Instructions
M4 screws x4
Template & Bracket
Security Torx driver
Wire Rope
G. OPTIONAL ACCESSORY:
1. YT-ICB45
2. YT-HU75
Flush Mount Kit
Heater kit
©2010 Sony Corporation. All rights reserved. Features and specifications are subject to change without
notice. Non-metric weights and measurements are approximate. Sony is a registered trademark of Sony
Corporation. Super HAD is a trademark of Sony Corporation.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 4