SPC - Solar Operation Manual Solar Powered Portion Control Scale SPC - Solar Operation Manual Read this manual before use and keep it handy YAMATO CORPORATION www.YamatoCorp.com 1775 S. Murray Blvd. Colorado Springs, CO 80916 USA Tel (719) 591-1500 Fax (719) 591-1045 YAMATO TECH CORPORATION #112-19425 Langley By-Pass Surrey, B.C. V3S 6K1 Canada Tel (604) 533-2338 Fax (604) 533-0827 YCO-130607 SPC - Solar Operation Manual Product Specificatons Model SPC-Solar 2 SPC-Solar 5 Lower Range 0 - 2.2 lb x 0.002 lb 0 - 2 lb 3 oz x 0.05 oz 0 - 35 oz x 0.05 oz 0 - 1000 g x 1 g 0 - 5.5 lb x 0.05 lb 0 - 5 lb 8 oz x 0.1 oz 0 - 88 oz x 0.1 oz 0 - 2500 g x 2 g High Range 2.2 - 4.4 lb x 0.005 lb 2 lb 3 oz - 44 lb 6oz x 0.1oz 35 - 70 oz x 0.1 oz 1000 - 2000 g x 2 g 5.5 - 11 lb x 0.01 lb 5 lb 8 oz - 11 lb 2 oz x 0.2 oz 88 - 178 oz x 0.2 oz 2500 - 5000 g x 5 g Maximum Tare 2.190 lb 2 lb 2.75 oz 34.75 oz 995 g 5.475 lb 5 lb 7.5 oz 87.5 oz 2490 g System Parameter Operation 1 Display Press and hold the key and press + keys to go to system parameter mode under the weighing mode. The indicator blinks during system parameter indicator lights up 2 The operation under system parameter mode is as follows : Move parameter No. forward (+1) : Move setting value forward (+1) : Move setting value backward (-1) * Be sure to set the setting value among available parameter values shown on the parameter list. When the setting value you desire has passed, press the key to move backwared (-1). Long Press the key to turn off the power to save the setting value in the memory 1 YCO-130607 SPC - Solar Operation Manual Parameter List ( # 01 - 04: User parameter, # 05 - 09: System parameter) Parameter 01 Description Power Select 02 Weighing units at power on 03 Checkweighing function Auto-off timer 04 05 Gravity compensation 06 Capacity 07 Zero tracking 08 09 Not used Not used Available parameter 000: Solar-powered operation (Default) 001: Battery-powered operation (Quick response) 002: Hybrid (Solar + Battery) operation (The response speed is the same as 000) 000: g 001: lb (Default) 002: oz 003: lb.oz 000: Disabled 001: Enabled (Default) 000: Disabled 001-009: Set by one minute (5 minute: Default) 000: Disabled 001-029: Prohibited to set 030-210: (Acceleration of Gravity (m/s2) - 9.7600) x 10000/5 + 30 (offset) Setting range: 9.7600 to 9.8500 m/s2 Minimum setting unit: 0.0005 m/s2 000: 2000 g 001: 5000 g 000: Disabled 001: Enabled (Default) 2 YCO-130607 SPC - Solar Operation Manual Calibration Prepare "kilogram" check weights (more than OIML M1 class) corresponding to the capacity. It is not possible to calibrate the SPC-Solar with either "pound" or "ounce" check weight. Be sure to calibrate the scale under battery-powered mode. Operation 1 2 3 Install batteries. Set the user parameter No. 01 (power select) at 001 (battery-powered operation) Press and hold the key and press the to user parameter mode. key to go Press and hold the to calibration mode key to go key and press the After confirming, the stable indicator the 4 Display lights up, press key. Place a check weight corresponding to the scale capacity. SPC - Solar 2: 2,000 grams SPC - Solar 5: 5,000 grams 5 When the stable indicator lights up, press key. If the display shows as right figures, calibration has been completed successfully If there is the following differences for the values in the right figures, turn off the power and try to calibrate it again Capacity 2 kg Capacity 5 kg SPC - Solar 2: more than +/- 5 counts SPC - Solar 5: more than +/- 10 counts After calibration, turn off the power. Turn on the power again and confirm that correct weight value is displayed 3 YCO-130607 SPC - Solar Operation Manual Error Messages When one of the following error messages appears on the display, follow the troubleshooting instructions. Contact the retailer from which the product was purchased, if other messages than the following appear, or an error is not recovered after following the troubleshooting. Display Cause Batteries are running out. Out of batteries The weight below zero This message appears when the weighed value is less than - 5 divisions (- 5 g for the weighing capacity of 2000 g). Troubleshooting Replace all of the batteries with new one. Do not use old and new batteries or alkaline and magnesium batteries at a time. Press the key. If the pan has been removed, set it on the scale again. This message appears when the weighed value is over +5 divisions (2010g for the weighing capacity of 2000g). When the item is removed, the display returns to the weighing screen. Make sure to use the scale within the capacity. Turned on the scale while a heavy item was placed Remove the item from the pan, and then press the key Turn on the scale while a foreign material was stuck between the main body and the pan Check if a foreign material is not stuck or does not contact the pan. Then press the key. Overloading The initial error (A) The initial error (B) Pressed the key while a heavy item was on the pan in the middle of the operation The initial error (C) The initial error (D) Turned on the scale while the item was left on a pan. Remove the item and press the key 4 The weight of the item is beyond the level where the key is operative.Remove the item from the pan, and then press the key. Make sure that nothing is left on the pan and turn on the scale again. YCO-130607 SPC - Solar Operation Manual Wiring Diagram 5 YCO-130607 SPC - Solar Operation Manual Parts List 6 YCO-130607 SPC - Solar Operation Manual Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17,18,20,23,25 19 21 22 24 Part # 63910024 63910028 63910025 63910020 63910102 63910103 63911031 63900031 63900032 63900023 63901034 63900037 63900035 63910036 63910034 63910033 63910021 63910022 63911001 63911002 63911003 63911004 63911005 Description Platform Cover, S.S. Plate, Platform Support Cushion Rubber Upper Housing Load cell + PCB Assembly, 2 kg Load cell + PCB Assembly, 5 kg Battery Box Battery Box Holder Battery Lid with sponge Holding Plate / CPU Board Solar Panel Membrane Key Switch Front Mask, SPC - Solar 2 Front Mask, SPC - Solar 5 Solar Glass Display Glass Base Rubber Foot Hex Bolt & SW, M3X6, S.S. Screw & Washer, M2X6 / Battery Box Hex Bolt, M4X8, S.S. / Battery Lid Screw & Washer, M3X6 / CPU Board Hex Nut M4 / Rubber Foot 7 Qty / Unit 1 1 4 1 1 1 1 1 1 1 2 1 1 1 2 1 1 4 17 2 2 4 4 YCO-130607 SPC - Solar Operation Manual YAMATO CORPORATION www.YamatoCorp.com 1775 S. Murray Blvd. Colorado Springs, CO 80916 USA Tel (719) 591-1500 Fax (719) 591-1045 YAMATO TECH CORPORATION #112-19425 Langley By-Pass Surrey, B.C. V3S 6K1 Canada Tel (604) 533-2338 Fax (604) 533-0827 YCO-130607