installation instructions
creative wall „Typ 1“
creative wall® „Typ 1“
sheet 1/6
detail
detail
Flughafenstr. 4 A
D-27809 Lemwerder
Telefon:+49(0)421 -69 35 2 - 0
Telefax: +49(0)421 -69 35 2 - 14
info@procedes.de
www.procedes.de
installation instructions
creative wall „Typ 1“
installation instructions for creative wall®
sheet 2/6
1) Screw the footplate 380 (an weighting plate 360 if necessary) or footplate 200
to the column.
2) Fit grub screw in stud for tensioning block and insert the groove in the column - one stud
for top and bottom.
3) In the case or multi-part section rails, connect hanging rails with a tube insert to form
a continuous upper and lower rail.
4) Insert tensioning blocks in the centre groove of the rail and roughly align.
5) Arrange upper section rail on the floor in the same position as the creative wall® is to later
stand in the room.
Place columns in the required position along the laid out rail (if the fabric wall is not freestanding, now secure column to floor with Spax - footplate 200 (see Fig. 1)).
6) Raise upper section rail, push the upper bolt to the approximate height and put the tension
block onto the preassembled bolt - then connect bolt and tension block wih the tensioning
screws and fix it.
7) Stand the roll of fabric on its end with the print subject facing forward. Carefully insert the
upper hollow hem with the hose insert in the upper section rail already suspendend while slowly
unrolling the fabric.
8) Bring the lower section rail into the lower seam of the fabric. Then bring the lower bolt to the
approximate height and stick the tension block onto the preassembled bolt - then connect bolt and
tension block with the slit screw and fix it.
9) Align upper section rail exactly straight. Pull fabric taut in the upper/lower section rail and
secure at both ends with the final retention screw.
10) In order to tighten the fabric tear the lower (lose) section rail down. Then tighten the lower
tension block again.
11) Fit end caps on ends of rails.
12) Preassemble hammer head screw with the flat knurled nut in hanging rail: Turn screw 90O and
secure with the flat knurled nut.
Fit lamp on hanging rail with preassembled hammer head screw and tighten withe knurled nut.
Connect 230 V power cable and if necessary interconnect extension/distributor block.
Flughafenstr. 4 A
D-27809 Lemwerder
Telefon:+49(0)421 -69 35 2 - 0
Telefax: +49(0)421 -69 35 2 - 14
info@procedes.de
www.procedes.de
installation instructions
creative wall „Typ 1“
sheet 3/6
clam
ping
bolt
bloc
k
set screw
binder
link-screw
slotted screw
cross section
column
base 380
accessories
shank core
end cap
profile 46/20/3
Flughafenstr. 4 A
D-27809 Lemwerder
Telefon:+49(0)421 -69 35 2 - 0
Telefax: +49(0)421 -69 35 2 - 14
info@procedes.de
www.procedes.de
installation instructions
creative wall „Typ 1“
sheet 4/6
1
woodscrew
2x M12/20
3
2x M12/30
(countersunk socket screw)
4x M5/8
2
4
M5/16
Flughafenstr. 4 A
D-27809 Lemwerder
Telefon:+49(0)421 -69 35 2 - 0
Telefax: +49(0)421 -69 35 2 - 14
info@procedes.de
www.procedes.de
installation instructions
creative wall „Typ 1“
sheet 5/6
5
5
M5/20
7
8
1.
2.
3.
M5/20
Flughafenstr. 4 A
D-27809 Lemwerder
Telefon:+49(0)421 -69 35 2 - 0
Telefax: +49(0)421 -69 35 2 - 14
info@procedes.de
www.procedes.de
installation instructions
creative wall „Typ 1“
sheet 6/6
9
10
M5/8
2.
1.
M5/8
11
12
5.
flat knurled nut
3.
2.
knurled screw
4.
T-headed screw
1.
Flughafenstr. 4 A
D-27809 Lemwerder
Telefon:+49(0)421 -69 35 2 - 0
Telefax: +49(0)421 -69 35 2 - 14
info@procedes.de
www.procedes.de