The City College of New York
Department of Civil Engineering
CE 345: Soil Mechanics
Instructor: Dr. George Mylonakis
LAB EXPERIMENT #2:
LIQUID LIMIT AND PLASTIC LIMIT
LIQUID LIMIT TEST
Introduction
When a cohesive soil is mixed with an excessive amount of water, it will be in a liquid state and flow like a
viscous liquid. When the viscous liquid dries gradually due to loss of moisture, it will pass into a plastic
state. With further loss of moisture, the soil will pass into a plastic state. With even further reduction of
moisture, the soil will pass into a semi-solid and then into a solid state.
The moisture content, w, (%) at which the cohesive soil will pass from a liquid state to a plastic state is
called the liquid limit of the soil. Similarly, plastic limit and shrinkage limit can be explained. These
limits are called Atterberg limits.
Atterberg Limits
Solid
Semisolid
Shrinkage Limit (SL)
Plastic
Plastic Limit (PL)
Moisture content increasing
Liquid
Liquid Limit (LL)
Equipment
1.
Casagrande liquid limit device
2.
Grooving tool
3.
Moisture cans
4.
Porcelain evaporating dish
5.
Spatula
6.
Oven
7.
Balance sensitive up to 0.01g
8.
Plastic squeeze bottle
9.
Paper towels
18
106751614
Procedure
2.
Determine the mass of moisture cans (W1).
3.
Put 250g of air-dry soil, passed through No. 40 sieve into an evaporating dish. Add water and mix the
soil to the form of a uniform paste.
4.
Place some soil paste into the liquid limit device. Smooth the surface with a spatula such that
maximum depth is 8 mm.
5.
Using the grooving tool, cut a groove along the centerline of the soil pat.
6.
Turn the crank at the rate of 2 revs. / second. Count the number of blows (N) for the groove in the soil
to close through a distance of ½ in. If N = 25-35, collect a moisture sample from the cup to a moisture
can and determine the mass (W2).
7.
If N < 25, place the soil back to the evaporating dish and clean the device. Stir the soil (to dry it up)
with spatula. Then redo steps 3, 4 and 5.
8.
Remove the soil from the cup of LL device and clean it carefully.
9.
Add more water to the soil paste in the evaporating dish and mix well. Repeat steps 3, 4 and 5 to get N
= 20-25. Take a moisture sample from the cup. Clean the LL device.
10. Add more water to the soil paste in the evaporating dish and mix well. Repeat steps 3, 4 and 5 to get N
= 15-20. Take a moisture sample from the cup. Clean the LL device.
11. Put three moisture cans in the oven to dry to constant mass (W3).
Calculation
1.
Calculate mass of can, W1 (g)
2.
Calculate mass of can + moist soil, W2 (g)
3.
Calculate mass of can + dry soil, W3 (g)
4.
Determine the moisture content for each of the three trials as
(W2 - W3) x 100
w (%) =
(W3 - W1)
Graph
Plot a semi-log graph between w (%) (arithmetic scale) vs. N (log scale). It should be a straight line, which
is called the flow curve. From the straight line, determine the moisture content w (%) corresponding to 25
blows. This is the liquid limit (LL) of the soil. The magnitude of the slope of the flow line is called the
flow index (FI).
w1 (%) - w2 (%)
FI =
log N2 - log N1
19
106751614
PLASTIC LIMIT TEST
Introduction
Plastic limit is defined as the moisture content, in percent, at which a cohesive soil will change from a
plastic state to a semisolid state. In the lab. the plastic limit is defined as the moisture content (%) at which
a thread of soil will just crumble when rolled to a diameter of 1/8 in. (3.18 mm).
Equipment
1.
Moisture cans
2.
Porcelain evaporating dish
3.
Spatula
4.
Ground glass plate
5.
Balance sensitive up to 0.01 g
6.
Plastic squeeze bottle
7.
Oven
Procedure
1.
Put 20g of air-dry soil, passed through No. 40 sieve into an evaporating dish.
2.
Add water and mix the soil thoroughly.
3.
Determine the mass of moisture cans (W1).
4.
From the moist soil prepared in step 2, prepare several ellipsoidal-shaped soil masses by squeezing the
soil with fingers.
5.
Take one of the ellipsoidal-shaped soil masses and roll it on a ground glass plate using the palm of the
hand. The rolling should be done at the rate of 80 strokes/min. Note that one complete backward and
one complete forward motion of the palm constitute a stroke.
6.
When thread of soil reaches 1/8” in diameter, break it up in to several small pieces and squeeze it to
form an ellipsoidal mass again.
7.
Repeat steps 5 and 6 until the thread crumbles into several pieces when d = 1/8”.
8.
Collect the small crumbled pieces into the moisture can and put the cover on the can.
9.
Take the other ellipsoidal soil masses formed in step 4 and repeat steps 5 through 8.
10. Determine the mass of moisture can plus wet soil (W2).
11. Place moisture can into the oven to dry to constant mass (W3).
20
106751614
Calculations
1.
Calculate mass of can , W1 (g)
2.
Calculate mass of can + moist soil, W2 (g)
3.
Calculate mass of can + dry soil, W3 (g)
4.
Calculate plastic limit
(W2 - W3) x 100
PL =
W3 - W1
5.
Calculate plasticity index, PI = LL – PL.
21
106751614
DATA SHEET: Liquid and Plastic Limit
Description of soil:
_____________________
Sample No.:
____________________________
Location:
____________________________
Tested by:
____________________________
Date:
___________________________________
LIQUID LIMIT TEST
Test No.
1
2
3
Can No.
Mass of can , W1(g)
Mass of can + moist soil, W2 (g)
Mass of can + dry soil, W3 (g)
(W2 - W3) x 100
w(%) =
W3 - W1
No. of blows, N
LL =
_____________________
FI =
_____________________
PLASTIC LIMIT TEST
Can No.
Mass of can , W1(g)
Mass of can + moist soil, W2 (g)
Mass of can + dry soil, W3 (g)
PL = (W2 - W3) x 100/ (W3 - W1)
PI = (LL - PL)
22
106751614