Antietam Fire Apparatus, Inc.
PROPOSAL
Antietam Fire Apparatus, Inc. is pleased to offer the proposed vehicle to meet the intent of the fire
department specifications. KME Fire Apparatus is a leading manufacturer in custom and commercial fire
fighting vehicles.
Questions or concerns pertaining to this proposal can answered by contacting the following KME
representative:
Bill White
Antietam Fire Apparatus
19932 Beaver Creek Road
Hagerstown, MD 21740
Phone: (301) 797-1410
(877) 378-2781
Cell:
(443) 336-6688
Fax:
(301) 797-1412
KOVATCH HISTORY
Kovatch brings to the fire and specialty vehicle market over five decades of broad-based
experience in vehicle manufacturing, sales and service. The company was founded in 1946 as a car and
truck repair business in Nesquehoning, PA.. Various automobile and truck franchises were eventually
acquired and continue to this day.
In the mid 1960's, Kovatch won its first rebuild contract for the US military. By the 1970's, the
company had a string of successful rebuild and new manufacture contracts for various branches of the
Defense Department. To this day, Kovatch is still known as a premier supplier of specialty apparatus to
the Federal government and is currently working on several contracts.
In the mid 1980's, Kovatch began a commercial fire apparatus division, now known as KME Fire
Apparatus. By combining decades of specialty vehicle experience with acquisitions of other
manufacturers, Kovatch offers unparalleled products and services. Today, Kovatch manufactures upward
of 500 vehicles per year for municipal and private fire and rescue service providers as well as the
government. Our apparatus can be found across the country and increasingly around the world.
The Kovatch headquarters complex consists of over one-half million square feet and is a totally
integrated manufacturing facility for emergency and specialty vehicles. The facilities include state of the
art fabrication, machining, welding, painting and finishing departments. We also have a technical manual
publication department for our vast line of products. Our knowledgeable workforce, including marketing,
engineering, and manufacturing personnel, work as a team to provide world-class quality. Other factory
locations include Ontario, California, Roanoke, Virginia and New York (near Albany.)
KME has a national distribution network in place for sales and service of fire apparatus, as well as
an international representative. Service and warranty matters are handled through our network as well as
our locations in Virginia, New York and California.
Allen Volunteer Fire Co., Inc. Tanker Specification
1
Antietam Fire Apparatus, Inc.
Quality is very important to Kovatch. There is an in-house Quality Assurance department that is
monitored by the Defense Contract Management Command (DCMC). Kovatch also has UL inspectors on
site. For out of house testing, we utilize the US Army's facility at Aberdeen Proving Ground as well as
private testing agencies. We offer training at the factory or at the Allen Volunteer Fire Company, Inc.,
premises.
KME offer a broad line of apparatus known worldwide for their quality and reliability. The line
includes commercial fuel transport trucks, aircraft refuelers, snow plows, and fire apparatus consisting of
pumpers, rescue trucks, rapid intervention vehicles, tankers, elliptical tankers, wildland units, and a full line
of aerial devices.
GENERAL INFORMATION
The proposed apparatus will be constructed to withstand the severe and continuous use
encountered during emergency fire fighting services. The apparatus shall be of the latest type, carefully
designed and constructed with due consideration to the nature and distribution of the load to be sustained.
These specifications detail the proposal for general design criteria of cab and chassis components,
aerial device (if applicable), fire pump and related components (if applicable), water tank (if applicable),
fire body, electrical components, painting, and equipment.
All items of these proposal specifications will conform to the National Fire Protection Association
Pamphlet No. 1901, latest edition.
KME will furnish satisfactory evidence of our ability to construct, supply service parts and technical
assistance for the apparatus specified.
The proposed chassis will be certified by KME as conforming to all applicable federal motor vehicle
safety standards (FMVSS) in effect at the date of contract. This will be attested to by the attachment of a
FMVSS certify caution label on the vehicle by KME, who will be recognized as the responsible final
manufacturer.
KME will be responsible for preparing and maintaining a record file of parts and assemblies used to
manufacture the proposed apparatus. These records will be maintained in KME's factory for a minimum of
twenty (20) years. The file will contain copies of any and all reported deficiencies, all replacement parts
required to maintain the apparatus, and original purchase documents including specifications, contract,
invoices, incomplete chassis certificates, quality control reports and final delivery acceptance documents.
The purchaser will have access to any and all documents contained in this file upon request.
"TOP OF THE LINE" CHASSIS
KME is proposing a custom built chassis, which is "Top Of The Line" including the cab structure
and design, Multiplex electrical system, drive train and frame assembly.
Allen Volunteer Fire Co., Inc. Tanker Specification
2
Antietam Fire Apparatus, Inc.
GENERAL CONSTRUCTION
The proposed apparatus, assemblies, subassemblies, component parts, etc., will be designed and
constructed with the due consideration to the nature and distribution of the load to be sustained and to the
general character of the service to which the apparatus is to subjected when placed in service. All parts of
the apparatus will be designed with a factor of safety, which is equal to or greater than that which is
considered standard and acceptable for this class of equipment in fire fighting service. All parts of the
proposed apparatus will be strong enough to withstand general service under full load. The apparatus will
be so designed that the various parts and readily accessible for lubrication, inspection, adjustment and
repair.
The apparatus will be designed and constructed, and the equipment so mounted, with due
consideration to distribution of the load between front and rear axles that all specified equipment, including
a full complement of specified ground ladders, full water tank, loose equipment, and firefighters will be
carried without overloading or injuring the apparatus.
The aerial ladder will be designed as a modular component of the apparatus. The aerial ladder, its
support structure, and outrigger system will be designed to comprise an integrated assembly, removable
from the carrier vehicle as a single self-supporting unit. The design will facilitate repair, modifications or
replacement of the aerial device, apparatus body, or chassis individually, as required by wear from use,
obsolescence, or for purposes of refurbishment.
SINGLE-LINE RESPONSIBILITY
KME is providing single source manufacturing. KME designs, manufactures and builds our own
fire apparatus cab, chassis, body and aerial device. This capability provides a consistent design and
manufacturing procedures that will reduce warranty issues and provide ease in parts replacement.
PRODUCT LIABILITY INSURANCE
KME is providing liability and facility insurance equaling $25,000,000.00, which is one of the
highest available in the fire industry. Reference attached documentation.
SERVICE CENTER AND PARTS DEPOT
Antietam Fire Apparatus, Inc.
KME FIRE APPARATUS SERVICE STATEMENT
The proposed KME Fire Apparatus vehicle is offered with service for in or out of warranty repairs
can be promptly performed by the local KME authorized service center.
Service is provided by:
Antietam Fire Apparatus, Inc.
19932 Beaver Creek Rd.
Allen Volunteer Fire Co., Inc. Tanker Specification
3
Antietam Fire Apparatus, Inc.
Hagerstown, MD 21740
Ph: (301) 797-1410
Toll free: (877) 378-2781
Fax: (301) 797-1412
Service Center Capabilities
Antietam Fire Apparatus, Inc. celebrates its 18 th year of operation and employs ten (10) people
and is proud to operate a Service Center in Hagerstown, MD. The privately owned operation employs four
(4) full-time service mechanics to handle any service-related problems or improvements that you may
desire.
Antietam Fire Apparatus, Inc. is a Hale Master Parts and Service Center that operates an on the
road service truck that can offer In Station Service repairs to your apparatus if needed.
Antietam Fire Apparatus, Inc. offers twenty-four (24) hour service in which assigned service
personnel carry pagers; one (1) man is always on call to handle any truck that is down and out of service.
The service facilities provide service to handle sheet metal repair and fabrication, pump and
electrical repair, aerial ladder service, and effect booster tank enlarging and replacement, and minor or
major refurbishment capabilities.
Service and repairs to all makes of fire apparatus including trucks with Hale, Waterous, Darley,
FMC and John Bean Pumps.
The Service Center employees are fully insured with Workmans Compensation, at 3 Million Dollar
Garage Keepers Liability Insurance Coverage and a 1 Million Dollar Products Liability Insurance Policy to
protect your fire department in case of injury to personnel or your fire department equipment.
PRICES AND PAYMENTS
The bid price will be F.O.B. Destination, on a delivered and accepted basis at the Fire Department.
Total price on KME's proposal sheet will include all items listed in these specifications. Listing any
items contained in the specification as an extra cost item, unless specifically requested to do so in these
specifications, will automatically be cause for rejection.
KME will compute pricing less federal and state taxes. It is understood that any applicable taxes
will be added to the proposed prices, unless the purchaser furnishes appropriate tax-exempt forms.
DELIVERY TIME
KME is proposing to complete the apparatus delivery time based on the number of calendar days,
starting from the date the sales contract is signed and accepted by KME Fire Apparatus.
Delivery Time: 270 – 300 Calendar Days
Allen Volunteer Fire Co., Inc. Tanker Specification
4
Antietam Fire Apparatus, Inc.
MATERIAL AND WORKMANSHIP
All equipment furnished will be guaranteed to be new and of current manufacture, to meet all
requirements of purchaser's specifications.
All workmanship will be of high quality and accomplished in a professional manner so as to insure
a functional apparatus with a pleasing, aesthetic appearance.
SALES ENGINEER
KME will designate an in house individual to perform the contractor's sales engineer functions.
The sales engineer will provide a single point interface between the purchaser and KME on all matters
concerning the contract.
APPROVAL DRAWING
A detailed drawing of the apparatus will be provided to the Allen Volunteer Fire Company, Inc., for
approval before construction begins. A copy of this drawing shall also be provided to the manufacturer's
representative. Upon Allen Volunteer Fire Company, Inc., approval, the finalized drawing shall become a
part of the total contract.
The drawing shall show, but is not limited to, such items as the chassis make and model, major
components, location of lights, sirens, all compartment locations and dimensions, special suctions,
discharges, etc. The drawing shall be a visual interpretation of the apparatus as it is to be supplied.
INSPECTION VISITS
KME will provide three (3) factory inspection trips to KME's facility. Transportation, meals, lodging,
and other requisite expenses will be the bidder's responsibility.
Accommodations shall be for six (6) Fire Department representatives per trip.
The factory visits shall occur at the following stages of production of the apparatus:
Pre-construction / blueprint review.
Mid point completion of entire apparatus.
Final inspection upon completion.
Travel arrangements less than 300 miles from the manufacturing facility shall be via ground
transportation.
The customer maintains the right to inspect the apparatus, within KME's normal business hours. At
any other point during construction expenses incurred during non-specified visits shall be the responsibility
of the customer.
Allen Volunteer Fire Co., Inc. Tanker Specification
5
Antietam Fire Apparatus, Inc.
During inspection visits, the customer reserves the right to conduct actual performance tests to
evaluate completed portions of the unit. Testing shall be accomplished with the assistance and resources
of the contractor.
DELIVERY
Delivery of the apparatus to the Fire Department will remain KME's responsibility.
A qualified and responsible representative of KME will deliver the apparatus to the Fire
Department.
INSTRUCTION MANUALS/DRAWINGS, SCHEMATIC
KME will supply at time of delivery, two (2) copies of a complete operation and service manual
covering the complete apparatus as delivered and accepted.
The manual will contain the following:





Descriptions, specifications, and ratings of chassis, pump (if applicable), and aerial device
(if applicable).
Wiring diagrams
Lubrication charts
Operating instructions for the chassis, any major components such as a pump and any
auxiliary systems.
Instructions regarding the frequency and procedures recommended for maintenance.
Parts replacement information.
VEHICLE FLUIDS PLATE
As required by NFPA-1901, KME will affix a permanent plate in the driver's compartment specifying
the quantity and type of the following fluids used in the vehicle:
A permanent plate in the driving compartment will specify the quantity and type of the following
fluids used in the vehicle:










Engine oil
Engine coolant
Chassis transmission fluid
Pump transmission lubrication fluid
Pump primer fluid
Drive axle(s) lubrication fluid
Air-conditioning refrigerant
Air-conditioning lubrication oil
Power steering fluid
Cab tilt mechanism
Allen Volunteer Fire Co., Inc. Tanker Specification
6
Antietam Fire Apparatus, Inc.




Transfer case fluid
Equipment rack fluid
Air compressor system lubricant
Generator system lubricant
PRINCIPAL APPARATUS DIMENSIONS & G.V.W.R.
The principal dimensions of the completed apparatus will not exceed the following maximum
acceptable dimensions:
KME's PROPOSED DIMENSIONS:




OVERALL LENGTH:
OVERALL WIDTH:
OVERALL HEIGHT:
WHEELBASE:
XXX"
XXX"
XXX"
XXX"
The axle and total weight ratings of the completed apparatus will not be less than the following
minimum acceptable weight ratings:



MINIMUM FRONT G.A.W.R.:
MINIMUM REAR G.A.W.R.:
MINIMUM TOTAL G.V.W.R.:
22,500 lbs.
48,000 lbs.
70,500 lbs.
KME will include the principal dimensions, front G.A.W.R., rear G.A.W.R., and total G.V.W.R. of the
proposed apparatus. Additionally, KME will provide a weight distribution of the fully loaded, completed
vehicle; this will include a filled water tank, specified hose load, miscellaneous equipment allowance in
accordance with NFPA-1901 requirements, and an equivalent personnel load of 250 lbs. per seating
position.
PRE-DELIVERY SERVICE
Included in the KME proposal and after transportation from the factory or immediately prior to
delivery to the fire department, the apparatus will receive a pre-delivery service consisting of: engine oil &
filter change, chassis lubrication, fuel filter(s) changed, adjustment of engine to manufacturers
specifications, complete inspection including all electrical and mechanical devices, for proper operation
and correction of leaks or obvious problems.
KME OWNERSHIP
KME is a tightly held family owned corporation. All of the stockholders are members of the Kovatch
family of Nesquehoning, PA. KME carries no (zero) long term debt and is the largest privately owned
manufacturer of fire apparatus in the country.
Allen Volunteer Fire Co., Inc. Tanker Specification
7
Antietam Fire Apparatus, Inc.
FAMA MEMBERSHIP
KME Fire Apparatus is a leading and proud member of the Fire Apparatus Manufacturer's
Association (FAMA).
U.S.A. MANUFACTURER
The entire apparatus shall be assembled within the borders of the Continental United States to
insure more readily available parts (without added costs and delays caused by tariffs and customs) and
service.
QUALITY MANAGEMENT
KME Fire Apparatus operates a Quality Management System under the requirements of MIL-I45208A, a military specification for a quality inspection system established to substantiate product
conformance to drawings, specifications, and contract requirements. A copy of the certificate of
compliance will be included in the bid.
STEPPING, STANDING, & WALKING SURFACES
All stepping, standing, and walking surfaces on the body will meet NFPA #1901 anti-slip standards.
Aluminum tread plate utilized for stepping, standing, and walking surfaces will be Alcoa No-Slip type. This
material will be certified to meet the NFPA #1901 standard. Upon request by the purchaser, KME will
supply proof of compliance with this requirement. All vertical surfaces on the body, which incorporate
aluminum tread plate material, will utilize the same material pattern to provide a consistent overall
appearance.
UNDERWRITERS LABORATORIES INC. (UL) EXAMINATION AND TEST PROPOSAL
If required by the specific chapters of NFPA-1901, the proposed unit will be tested and certified for
KME Fire Apparatus by Underwriters Laboratories Inc. (UL) Underwriters Laboratories Inc. (UL) is
recognized worldwide as a leading third party product safety certification organization for over 100 years.
UL has served on National Fire Protection Association (NFPA) technical committees for over thirty years.
INDEPENDENT TESTING ORGANIZATION QUALIFICATIONS




UL is a nationally recognized testing laboratory recognized by OSHA.
UL complies with the American Society for Testing and Materials (ASTM) Standard ASTM E543
"Determining the Qualifications for Nondestructive Testing Agencies."
UL has more than 40 years of automotive fire apparatus safety testing experience and 16 years of
factory aerial device testing and Certification experience. UL has more than 100 years of
experience developing and implementing product safety standards.
UL does not represent, is not associated with, nor is in the manufacture or repair of automotive
fire apparatus.
Allen Volunteer Fire Co., Inc. Tanker Specification
8
Antietam Fire Apparatus, Inc.



All test work for fire pumps outlined in NFPA 1901, Edition will be conducted.
UL has included a list of all factory aerial device manufacturers for whom testing is currently being
conducted on a regular basis.
UL carries ten million dollars in excess liability insurance for bodily injury and properly
damage combined.
All work outlined in NFPA 1914, current Edition, including nondestructive testing, will be conducted
at the manufacturer's facility.
PERSONNEL
The UL inspectors performing the test work on the units are certified to Level II in the required NDT
methods, under the requirements outlined in ASNT document CP-189.
The actual person(s) performing the inspection will present for review proof of Level II Certification
in the required NDT methods.
Prior to submittal to the automotive fire apparatus manufacturer, the final Report will be reviewed
by the Supervisor of Fire Equipment Services and a Registered Professional Engineer, both of whom are
directly involved with the aerial device certification program at UL.
GENERAL APPARATUS DESCRIPTION "MOBILE WATER SUPPLY"
The unit shall be designed to conform fully to the "Mobile Water Supply Fire Apparatus"
requirements as stated in the NFPA 1901 Standard (2009 Revision), which shall include the following
required chapters as stated in this revision:









Chapter 1
Chapter 2
Chapter 3
Chapter 4
Chapter 7
Chapter 12
Chapter 13
Chapter 14
Chapter 15
Administration
Referenced Publications
Definitions
General Requirements
Mobile Water Supply Fire Apparatus
Chassis and Vehicle Components
Low Voltage Electrical Systems and Warning Devices
Driving and Crew Areas
Body, Compartments and Equipment Mounting
CAB SAFETY SIGNS
The following safety signs shall be provided in the cab:



A label displaying the maximum number of personnel the vehicle is designed to carry shall be
visible to the driver.
“Occupants must be seated and belted when apparatus is in motion” signs shall be visible from
each seat.
“Do Not Move Apparatus When Light Is On” sign adjacent to the warning light indicating a hazard if
Allen Volunteer Fire Co., Inc. Tanker Specification
9
Antietam Fire Apparatus, Inc.

the apparatus is moved (as described in subsequent section).
A label displaying the height, length, and GVWR of the vehicle shall be visible to driver. This label
shall indicate that the fire department must revise the dimension if vehicle height changes while
vehicle is in service.
CHASSIS DATA LABELS
The following information shall be on labels affixed to the vehicle:
Fluid Data:















Engine Oil
Engine Coolant
Chassis Transmission Fluid
Pump Transmission Lubrication Fluid
Pump Primer Fluid (if applicable)
Drive Axle(s) Lubrication Fluid
Air Conditioning Refrigerant
Air Conditioning Lubrication Oil
Power Steering Fluid
Cab Tilt Mechanism Fluid
Transfer Case Fluid
Air Compressor System Lubricant
Generator System Lubricant
Front tire cold pressure
Rear tire cold pressure
Chassis Data:





Chassis Manufacturer
Production Number
Year Built
Month Manufactured
Vehicle Identification Number
Manufacturers weight certification:



Gross Vehicle (or Combination) Weight Rating (GVWR or GCWR)
Gross Axle Weight Rating, Front
Gross Axle Weight Rating, Rear
ROLLOVER STABILITY
The apparatus shall meet the criteria defined in 4.13.1 for rollover stability as defined in the 2009
NFPA Standard for Automotive Fire Apparatus.
Allen Volunteer Fire Co., Inc. Tanker Specification
10
Antietam Fire Apparatus, Inc.
"PREDATOR" CAB TYPE
 FULL TILT
 CONTOUR WINDSHIELD
The cab shall be a custom tilt style, built specifically for fire service. The cab shall be a cab over
engine design, with integral tilt mechanism and engine access from inside the cab.
Cab shall be designed, fabricated, assembled in its entirety, and installed on the frame rails in the
factory of the bidder. This requirement shall eliminate any split responsibility in warranty and service. NO
EXCEPTIONS TO THIS REQUIREMENT.
OPEN SPACE DESIGN
The cab interior shall be the "Open-Space" design with no wall or window between the front and
rear crew area to allow direct communication, better visibility and air circulation in the cab.
CAB MATERIAL
The cab shall be fabricated from 5052-H 32 aluminum alloy, utilizing the minimum material
thickness as follows:







Cab side panels
Cab roof
Forward cab front sheet
Interior cab panels
Other panels
Cab doors
Engine enclosure side panels
0.125 thick (1/8")
0.125 thick (1/8")
0.125 thick (1/8")
0.125 thick (1/8")
0.125 thick (1/8")
0.1875 thick (3/16")
0.250 thick (1/4")
CAB - BASE CONSTRUCTION
Cab sub-frame shall be a welded assembly fabricated of 6063 structural aluminum alloy. This
frame shall extend the full length and width of the cab and be secured to the chassis frame through two (2)
rear urethane self centering load cushions, two (2) forward pivot brackets, and two (2) cab locks. The cab
shall be of entirely welded construction.
The front cab wall shall be of double wall type construction, featuring an inner and outer panel.
(No Exceptions)
CRASH TESTING CERTIFICATION
To ensure the safety of the cab occupants and cab integrity, proof of third party testing shall be
provided. The cab shall be certified for SAEJ2422 side impact, SAEJ2420 with ECER29 cab front impact,
Allen Volunteer Fire Co., Inc. Tanker Specification
11
Antietam Fire Apparatus, Inc.
and ECER29 cab roof strength. NO EXCEPTIONS
DIMENSIONS - EXTENDED LONG FOUR DOOR STYLE CAB
Minimum Cab Dimensions:













Overall width
Inside width across ceiling
Front area floor to ceiling
Top of front seat to ceiling
Seat back to steering wheel
Inside width (door to engine enclosure)
Inside width (door to engine enclosure)
Crew seat area width
Outer crew seat risers to rear wall
Centerline axle to rear wall
Rear of engine enclosure to rear cab wall
Centerline axle to front of cab
Floor to top of engine enclosure
96"
88"
63"
44" (depending upon seat type)
22" (depending upon seat type)
25" (driver's side, at floor)
22-1/2" (officer's side, at floor)
88"
59-1/2"
77-1/2"
60"
74"
31-1/2"
Glass Area Dimensions:




Windshield (Contour)
Front door window, retractable
Rear door window, retractable
Side fixed crew windows
2,900 sq. in.
743 sq. in. each
875 sq. in. each
620 sq. in. each
Cab Entry Door Dimensions




Forward door opening
Forward door recessed step
Rear door opening
Rear door recessed step
73" high x 37" wide
30" wide by 8-1/2" deep
95-3/4" high x 31" wide
20" wide x 8-1/2" deep
CAB ROOF
The roof shall be of a split level design with radius edges for an aesthetic, streamline appearance.
The roof shall be constructed of aluminum skin and shall be internally reinforced using extruded aluminum
framing which shall span the entire width and length of the cab for maximum structural integrity. This shall
allow the roof to support personnel and roof mounted equipment without the need for additional
reinforcement.
The cab roof over the rear crew area shall be raised twenty two (22) inches higher than the front
driver and officer area. The front face of the raised roof section shall be sloped at a 45 degree angle,
creating a streamlined interface with the standard, lower, forward roof section. This design shall allow for
additional interior height in the rear crew area.
Allen Volunteer Fire Co., Inc. Tanker Specification
12
Antietam Fire Apparatus, Inc.
The rear crew area doors shall be "Vista-Style", extending full height to the radius edge of the raised roof.
Approximate dimensions:


Crew area floor to ceiling
Top of crew seat to ceiling
75-1/2"
57" (depending upon seat type)
CAB ROOF DRIP RAIL
For enhanced protection from inclement weather, a drip rail shall be furnished on the sides of the
cab. The drip rail shall be constructed of bright polished extruded aluminum, and be fastened to the sides
of the cab rood edge. The drip rail shall extend the full length of the cab roof.
CAB DOORS
Four (4) side-opening doors shall be provided. The cab doors shall be totally aluminum
construction with an extruded aluminum frame and a 3/16" thick aluminum outer door skin. Doors shall be
full height from the step to the cab roof rain gutter and enclose the step area when the doors are closed.
The forward cab door opening shall be a minimum of 37" wide, and the rear cab door opening shall
be a minimum of 31" wide. The rearward cab doors shall have a radius cutout allowing the door opening
to protrude forward over the cab wheel well, while providing full access to the rear crew area.
There shall be a heavy duty piano type stainless steel hinge on each door with a minimum pin
diameter of 5/16". Hinges shall be slotted for ease of horizontal and vertical adjustment. There shall be a
cab door seal and the doors shall close flush with the side of the cab. A heavy-duty 6" wide belting
material shall be utilized to prevent the cab doors from opening greater than 90 degrees.
ENTRY STEP AREA
Each of the forward entrance steps shall be a minimum of 8-1/2" deep x 30" wide with the floor
board recessed a minimum of 3" to avoid "shin knocking". Each step shall be fabricated as an integral
part of the cab construction. The cab step and risers shall be overlaid with bright finish aluminum tread
plate.
Each of the rear entrance steps shall be a minimum of 8-1/2" deep x 20" wide. An intermediate
step shall be provided between the lower entrance step and the crew area floor for ease of entry and
egress. Each set of steps and respective step risers shall be constructed as an integral part of the cab
construction and shall be overlaid with bright finish aluminum tread plate.
DOOR LATCHES
Heavy-duty, bright finish cast paddle latches shall be provided on the interior and exterior of each
cab door. Door latch mechanisms which utilize spring steel clamps shall not be considered due to their
tendency to both rust and break. The interior door latch cables are to be designed to reduce adjustment
Allen Volunteer Fire Co., Inc. Tanker Specification
13
Antietam Fire Apparatus, Inc.
or possible wear at the adjustment turnbuckles.
DOOR WINDOWS
Each side cab door shall have a tinted retractable window operated by a hand crank mechanism.
The window track shall be designed into the door frame extrusion, which shall be extruded with a track
groove to house a window track and seal. The window shall be capable of being removed from an access
slot designed in the bottom of the door frame.
Each side cab door window shall be designed with a custom extruded trim plate, which shall
conform to the perimeter of the window cut out in each door. The trim plate shall extend from the edge of
the door skin to the window and shall have a silver anodized finish.
INNER DOOR PANELS
The cab door interior panels shall be covered with a one piece, polished stainless steel panel, full
height. The panel shall be 16 gauge stainless steel with a mirror finish and shall be designed to allow easy
access to the inner door.
Each interior cab door panel shall be equipped with a "STOP" sign type decal. The decals shall be
made from Scotchlite material and shall cover at least 96 in². The decal shall be octagonal and shall be
10" in size.
DOOR JAMB SCUFF PLATES
Each cab door jamb shall be equipped with a polished stainless steel scuff plates to protect the cab
paint when exiting and entering the cab. The scuff plate shall extend from the bottom of the door to the
top of the door.
EXTERIOR CAB TRIM
A high luster stainless steel trim band shall be provided along the cab sides, same height as the
bumper. Black vinyl trim molding shall be installed along the top and bottom of the trim band.
TRANSVERSE EXTERIOR CAB COMPARTMENTS
Two (2) compartments shall be provided, to the rear of the crew cab doors. The compartments
shall be approximately 38" high, 20" wide and 25 3/4" deep in the lower area and transverse above the
frame rails. The transverse section shall be approximately 20" wide x 18" high. The transverse section
shall be designed to be capable of being utilized for a seat riser. To make the compartment accessible
from inside the crew area the front wall of the transverse section shall be with two (2) flat panel drop down
doors.
The exposed section of the compartment in the rear crew area shall be painted with a textured
paint to match the cab interior. The interior of the compartment shall be painted to match the color or
Allen Volunteer Fire Co., Inc. Tanker Specification
14
Antietam Fire Apparatus, Inc.
material provided in the body compartments.
Compartment door shall have a 3/16" aluminum exterior skin door with a one (1) inch box pan and
a stainless steel "D" ring handle. Door shall be hinged on the forward edge with a stainless steel vertical
piano hinge so it opens toward the rear cab door. The door shall be held in the open position by a gas
shock stay arm.
Each compartment shall contain a flush mounted light for illumination of the compartment and shall
be wired to a door jamb switch to automatically come on when the door is opened.
WINDSHIELD/GLASS
A one piece, symmetrical, safety glass windshield shall be provided on the cab for the driver and
officer providing a clear viewing area. The windshields shall be full width to the center of the front cab
support for each side and provide the occupants with a panoramic view. To provide enhanced peripheral
vision on each side of the cab, the windshield and cab structure shall be designed with radius corners,
which provide a minimum of 8" of glass area, measured from the glass face to the side edge near the
door post. The windshield shall consist of three (3) layers; the outer light, the middle safety laminate and
the inner light. The thick outer light layer shall provide superior chip resistance, the middle safety laminate
layer shall prevent the windshield glass pieces from detaching in the event of breakage and the inner light
shall provide yet another chip resistant layer.
The windshield will be a contour design with 2900 sq. in. of area for improved visibility and style.
The windshield glass shall be designed so it can be used on either the driver or officer side. Windshields
that are epoxied or bonded to the cab structure will not be acceptable.
WINDSHIELD WIPERS AND WASHER
Dual, electric operated, pantographic type windshield wipers shall be provided. One (1) electric
drive motor must be provided for each wiper. Windshield wiper systems which utilize a single motor and a
reciprocating actuator arm shall not be considered.
Wipers shall have "HI/LO" and "INTERMITTENT" operating speeds. "HI/LO" speeds shall be
controlled by a steering column control, within the turn signal control stem. "INTERMITTENT" operation
shall be controlled by a twist switch within the control on the steering column. The wipers shall be of the
self-parking type.
Windshield washers shall be electric operated wet-arm type with a 3/4 gallon washer fluid
reservoir, mounted inside the engine enclosure and readily accessible through the engine hatch at the rear
of the engine enclosure. The washer control shall be integral with the intermittent wiper control switch.
There shall be individual removable panels on the front face of the cab for access to the wiper
motor assemblies.
CAB SIDE VIEWING WINDOWS
A fixed, tinted window with 620 sq. in of glass area shall be provided on each side of the cab
Allen Volunteer Fire Co., Inc. Tanker Specification
15
Antietam Fire Apparatus, Inc.
behind the forward cab doors. This window shall be the same height as the window in the rear cab door
for maximum visibility.
DARK TINTED REAR WINDOW GLASS
The windshield and the forward cab door glass shall be provided with standard DOT green
automotive tint. The side cab windows to the rear of the front doors, the rear cab door windows and any
rear viewing windows shall be equipped with a dark automotive tint. The use of stick on material shall not
be acceptable.
GRAB HANDLES
Four (4) 1-1/4" diameter x 28" long, polished aluminum, with rubber inserts, grab rails shall be
provided, one (1) at each cab door entrance. Grab rail stanchions shall be chrome plated and of an offset
design, when necessary, to prevent "hand-pinching" when opening or closing the doors. Formed rubber
gaskets shall be provided between each stanchion base and the cab surface.
INTERIOR GRAB RAILS
Four (4) vertically mounted 12” black cast aluminum “D” style entry assist handles shall be
installed, one (1) on each side of the cab interior on the “A” post and one (1) on each side of the cab
interior on the “C” post in the crew area to assist in entry and exiting of the cab.
Each front cab door shall be provided with one (1) horizontally mounted, 11" long, black cast
aluminum "D" style entry assist handle on the interior door panel to assist in entry and exiting of the cab
and for closing the door.
Each rear cab door shall be provided with one (1) horizontally mounted, 11" long, black cast
aluminum "D" style entry assist handle on the interior door panel to assist in entry and exiting of the cab
and for closing the door. Each rear cab door shall also be provided with one (1) horizontally mounted, 30"
long black cast aluminum "D" style assist handle, located approximately 8" above the bottom of the
window opening.
AIR INTAKE/OUTLET
There shall be a front air intake with a minimum of 945 square inches of open area for maximum
air flow to the charge air cooler and the radiator.
Two (2) air inlets/outlets with a minimum of 43.5 square inches per inlet shall be provided
horizontally above the wheel well opening, one on each side of the cab. The design shall permit proper
ducting of air through the engine compartment and cooling system. The left side inlet, used for the air
intake to the air cleaner, shall be equipped with an ember separator for separating water and burning
embers from the air intake system. This system shall be such that particles larger than .039 inches (1 mm)
in diameter can not reach the air filter element.
The air intake and outlets shall be covered with polished stainless steel louvers, secured with
Allen Volunteer Fire Co., Inc. Tanker Specification
16
Antietam Fire Apparatus, Inc.
polished cast aluminum housings.
WHEEL WELL LINERS - Stainless Steel
The front cab wheel wells shall be equipped with fully removable, bolt-in, 12 gauge stainless steel
inner wheel well liners. The liners shall extend full depth into the truck frame. The completely washable
wheel well liners shall be designed to protect the cab substructure, inner panels and other miscellaneous
installed components from road salts, debris, dirt accumulation and corrosion. Fender liners which are
fixed or only partially removable shall not be considered.
FENDERETTES
The cab wheel well openings shall be trimmed with replaceable, bolt-in, polished stainless steel
fenderettes. The fenderettes shall be secured to the cab with stainless steel threaded fasteners along the
internal perimeter of the wheel well. Rubber welting shall be installed between the fenderettes and the
cab side panel.
MUD FLAPS
Heavy duty, black rubber type mud flaps shall be provided behind the front wheels.
CAB MIRRORS
Each forward cab door shall have a 16" x 6-1/2", heated and motorized, stainless steel, West
Coast type mirror mounted on a swing-away, bow type, stainless steel bracket. Each mirror shall be
individually remote controlled from the driver's position. The mirror heating elements shall be controlled by
a single dash mounted switch. Two (2) 6" diameter, stainless steel, convex spot mirrors shall also be
provided, one (1) on each main mirror bracket.
INTERIOR CAB TRIM
The cab interior shall be constructed to create an ergonomically designed interior to be user
friendly and functional for the driver and officer.
The forward overhead panel shall be covered with a one-piece custom formed ABS vinyl overlay,
which shall have integrated windshield defroster/heat vents.
All ABS formed material panels, as well as all of the interior upholstery panels shall be medium
gray in color. The upholstered cab overhead and side wall portions shall utilize gray Durawear upholstery
with padding underneath to provide additional insulation.
The interior metal surfaces of the cab shall be finish painted with a textured gray paint.
Allen Volunteer Fire Co., Inc. Tanker Specification
17
Antietam Fire Apparatus, Inc.
INTERIOR REAR WALL
The interior rear wall of the cab shall be covered with gray Durawear for durability and shall match
the other upholstered areas of the cab.
A twelve (12) inch high bright finish aluminum tread plate scuff plate shall be provided on the lower
portion of the rear interior cab wall.
STORAGE COMPARTMENTS
There shall be a compartment provided under each front seat with a latched access door. The
compartment shall measure 8-3/4"W x 7-7/8"D x 4-3/4"H.
BARYFOL FLOORING
The floor of the driver’s compartment and the floor of the crew area shall be lined with BARYFOL
vinyl composite flooring to comply with NFPA noise and heat requirements.
The material utilized for this application shall be certified to meet the NFPA 1901, 2003 revision for
anti slip walking surfaces.
ENGINE ENCLOSURE
The forward portion of the engine enclosure shall be covered with a vinyl ABS material formed
overlay to match the balance of the cab interior. To allow maximum "elbow room" for the driver and
officer, the forward portion of the engine enclosure shall feature a contour shape. The engine enclosure
shall not significantly obstruct the driver's vision in any direction. The enclosure shall be an integral part of
the cab structure, which shall be constructed from .250 5052-H32 aluminum, providing adequate strength
to support radio, map boxes, etc. The engine enclosure shall be insulated to protect from heat and sound.
The noise insulation shall keep the DBA level within the limits stated in the current NFPA series 1900
pamphlet.
A padded, hinged access door shall be provided in the top rearward portion of the engine
enclosure. The door shall allow access to the engine oil, transmission fluid, power steering fluid level
dipsticks and the windshield washer fluid reservoir. The access door shall be provided with two (2) flush
mounted latches and gas shock holders. There shall be a vinyl ABS material cover over the access door
to give a cleaner look to the top of the engine enclosure and doghouse area.
DRIVER'S SEAT
The driver's seat shall be a H. O. Bostrom Sierra Air-50FX/HD air suspension, high back bucket
seat. The seat shall have a tapered and padded seat cushion with lumbar support. The seat shall have a
five inch fore and aft adjustment, a three inch height adjustment with heavy duty damper and a fixed seat
back. The seat air ride suspension shall be pneumatically controlled from a control switch on the forward
lower edge of the seat.
Allen Volunteer Fire Co., Inc. Tanker Specification
18
Antietam Fire Apparatus, Inc.
A red 3-point shoulder harness with lap belt shall be provided as standard equipment.
OFFICER'S SEAT
The officer's seat shall be a H. O. Bostrom Tanker 450 Air-50 series air-suspension, high back
bucket seat. The seat shall have a tapered and padded seat cushion with lumbar support. The seat shall
have a five inch fore and aft adjustment, a three inch height adjustment with heavy duty damper and a
reclining seat back. The seat shall include a SCBA storage area with integral headrest. The seat air ride
suspension shall be pneumatically controlled from a control switch on the forward lower edge of the seat.
A red 3-point shoulder harness with lap belt shall be provided as standard equipment.
The officer's seat shall include a H. O. BOSTROM Secure All™ SCBA Locking System. The
bracket system shall be free of straps and clamps that may interfere with auxiliary equipment on SCBA
units. The center guide fork shall keep the tank in-place for a safe and comfortable fit in seat cavity. Fire
fighters shall simply push the SCBA unit against the pivot arm to engage the patented auto-locking
system. Once the lock is engaged, the top clamp shall surround the top of the SCBA tank for a secure fit in
all directions.
The standard release handle shall be integrated into the seat cushion for quick and easy release
and shall eliminate the need for straps or pull cords to interfere with other SCBA equipment.
CREW AREA SEATING, X-LFD CAB
DRIVER'S SIDE REAR FACING CREW SEAT
The driver's side outboard rear facing crew seat shall be a H. O. Bostrom Tanker 450 ABTS series
fixed base high back bucket seat. The seat shall have a tapered and padded seat cushion with lumbar
support. The seat shall include a SCBA storage area with integral headrest.
The seat shall be equipped with a red integrated 3-point shoulder harness with lap belt and an
automatic retractor built into the seat assembly.
The driver's side rear facing outboard seat shall include a Zico model QLM-U "Quic-Lock"
mechanical bottle bracket and restraint assembly. The restraint system will be equipped with an easily
accessible mechanical release at the bottom of the assembly.
OFFICER'S SIDE REAR FACING CREW SEAT
The officer's side outboard rear facing crew seat shall be a H. O. Bostrom Tanker 450 ABTS series
fixed base high back bucket seat. The seat shall have a tapered and padded seat cushion with lumbar
support. The seat shall include a SCBA storage area with integral headrest.
The seat shall be equipped with a red integrated 3-point shoulder harness with lap belt and an
automatic retractor built into the seat assembly.
The officer's side rear facing outboard seat shall include a H. O. BOSTROM Secure All™ SCBA
Locking System. The bracket system shall be free of straps and clamps that may interfere with auxiliary
Allen Volunteer Fire Co., Inc. Tanker Specification
19
Antietam Fire Apparatus, Inc.
equipment on SCBA units. The center guide fork shall keep the tank in-place for a safe and comfortable fit
in seat cavity. Fire fighters shall simply push the SCBA unit against the pivot arm to engage the patented
auto-locking system. Once the lock is engaged, the top clamp shall surround the top of the SCBA tank for
a secure fit in all directions.
The standard release handle shall be integrated into the seat cushion for quick and easy release
and shall eliminate the need for straps or pull cords to interfere with other SCBA equipment.
DRIVER'S SIDE FORWARD FACING CREW SEAT
The driver's side outboard forward facing crew seat shall be an H. O. Bostrom Tanker 450 ABTS
series fixed high back bucket seat. The seat shall have a tapered and padded seat cushion with lumbar
support. The seat shall include an SCBA storage area with integral headrest.
The seat shall be equipped with a red integrated 3-point shoulder harness with lap belt and an
automatic retractor built into the seat assembly.
The driver's side outboard forward facing crew seat shall have a standard seat base.
The driver's side forward facing outboard seat shall include a H. O. BOSTROM Secure All™ SCBA
Locking System. The bracket system shall be free of straps and clamps that may interfere with auxiliary
equipment on SCBA units. The center guide fork shall keep the tank in-place for a safe and comfortable fit
in seat cavity. Fire fighters shall simply push the SCBA unit against the pivot arm to engage the patented
auto-locking system. Once the lock is engaged, the top clamp shall surround the top of the SCBA tank for
a secure fit in all directions.
The standard release handle shall be integrated into the seat cushion for quick and easy release
and shall eliminate the need for straps or pull cords to interfere with other SCBA equipment.
OFFICER'S SIDE FORWARD FACING CREW SEAT
The officer's side outboard forward facing crew seat shall be an H. O. Bostrom Tanker 450 ABTS
series fixed high back bucket seat. The seat shall have a tapered and padded seat cushion with lumbar
support. The seat shall include an SCBA storage area with integral headrest.
The seat shall be equipped with a red integrated 3-point shoulder harness with lap belt and an
automatic retractor built into the seat assembly.
The officer's side outboard forward facing crew seat shall have a standard seat base.
The officer's side forward facing outboard seat shall include a H. O. BOSTROM Secure All™
SCBA Locking System. The bracket system shall be free of straps and clamps that may interfere with
auxiliary equipment on SCBA units. The center guide fork shall keep the tank in-place for a safe and
comfortable fit in seat cavity. Fire fighters shall simply push the SCBA unit against the pivot arm to engage
the patented auto-locking system. Once the lock is engaged, the top clamp shall surround the top of the
SCBA tank for a secure fit in all directions.
The standard release handle shall be integrated into the seat cushion for quick and easy release
Allen Volunteer Fire Co., Inc. Tanker Specification
20
Antietam Fire Apparatus, Inc.
and shall eliminate the need for straps or pull cords to interfere with other SCBA equipment.
CENTER FORWARD FACING CREW SEATS
One (1) center inboard forward facing crew seat shall be provided, seat shall be an H. O. Bostrom
Tanker 450 ABTS series fixed high back bucket seat. Seat shall have a tapered and padded seat cushion
with lumbar support. Seat shall include an SCBA storage area with integral headrest.
Seat shall be equipped with a red integrated 3-point shoulder harness with lap belt and an
automatic retractor built into the seat assembly.
This seat will be centered, with the DS and OS forward facing rear seats evenly spaced.
Giving space on both sides of all rear seats
The one (1) center inboard forward facing crew seats shall have standard seat bases.
The center forward facing seat shall include a H. O. BOSTROM Secure All™ SCBA Locking
System. The bracket system shall be free of straps and clamps that may interfere with auxiliary
equipment on SCBA units. The center guide fork shall keep the tank in-place for a safe and comfortable fit
in seat cavity. Fire fighters shall simply push the SCBA unit against the pivot arm to engage the patented
auto-locking system. Once the lock is engaged, the top clamp shall surround the top of the SCBA tank for
a secure fit in all directions.
The standard release handle shall be integrated into the seat cushion for quick and easy release
and shall eliminate the need for straps or pull cords to interfere with other SCBA equipment.
SEAT UPHOLSTERY MATERIAL
The seats shall be upholstered with heavy duty gray tweed Durawear material as provided by
Bostrom.
SEAT BELT CUSHION SENSORS AND BELT SENSORS
The apparatus shall be equipped with a IMMI seat belt warning system. The system shall consist of
a Seat Belt module, dash mounted display and an audible alarm.
Seat belt and seat cushion sensors shall be provided on the seven (7) specified seating positions.
VEHICLE DATA RECORDER
An IMMI Vehicle Data Recorder (VDR) system shall be provided to meet the NFPA 1901, 2009
revision requirements. The system shall include an NFPA compliant "Black Box" with reporting software
that shall be capable of data storage to coincide with the NFPA requirements.
Data storage capabilities shall include interfaces with the following systems:
Allen Volunteer Fire Co., Inc. Tanker Specification
21
Antietam Fire Apparatus, Inc.




















Display module (Master Optical Warning Device)
Seat belt monitoring (seat occupied with seat belt)
Surface or panel mount
VDR, date & time stamp
Max Vehicle speed (MPH)
Vehicle acceleration / deceleration (MPH/Sec.)
Engine Speed (RPM)
ABS event
Data password protected
Data sampled once per second, in 48-hour loop
Data sampled min by min for 100 engine hours
Throttle position (% of Throttle)
Data software
Data interface for data download
PC / Mac Compatible
Hours Driven
Data summary reports
Last Minute Log
Idle Time
Track inputs from RollTek (If Equipped)
ADVANCED OCCUPANT RESTRAINT SYSTEM
The cab shall be equipped with advanced occupant restraint systems. This system shall function in
the event of a side roll over and shall be compatible with occupants ranging from a 5th percentile female to
95th percentile male.
This system consists of a roll sensor, seat and occupant pretensioner; buckle pretensioners and
inflatable side airbags. This system shall be functionally active while the truck is in operation.
A hybrid or pyrotechnic inflator shall inflate the side airbags. The bag should remain inflated to the
extent of providing head cushioning for 10 seconds after inflation. Pretensioners should be compatible with
either ABTS or body mounted seats and seat belts. Buckle pretensioners shall be used on static or power
seats where there is no air suspension. The buckle pretensioners must be capable of stroking 125 mm.
ROLL SENSOR
The roll sensor continually monitors the roll rate and angle of the vehicle, and deploys safety
devices when a roll event occurs. Deployment determination is made by a combination of vehicle angle
and angular rate. Vehicle deployment angle shall never exceed 60 degrees.
The roll sensor performs self-diagnostics each time the vehicle is started. A dash-mounted light
shall turn off after approximately 10 seconds if the sensor is functioning. During operation, the roll sensor
monitors for proper connection to each safety device in the vehicle once per second. If improper
connection is measured at any device or if an internal fault occurs, the roll sensor shall illuminate the
dash-mounted light. The system shall continue to function in the event of non-critical faults. System
Allen Volunteer Fire Co., Inc. Tanker Specification
22
Antietam Fire Apparatus, Inc.
diagnostics are on the SAE J1587 bus.
DRIVER'S POSITION
If the Driver's position is equipped with a suspension seat, in addition to the 3-point seat belt, an
occupant and seat pretensioning system and an inflatable side airbag shall be used.
In the event a non-suspension seat is used in the Driver's position, a buckle-pretensioning device
shall be used in conjunction with an inflatable side airbag. The seat and occupant pretensioning system
should function and position the occupant prior to the side airbag deployment.
OFFICER'S POSITION
In addition to the 3-point seat belt, the Officer's position shall be equipped with a buckle
pretensioning device and inflatable side airbag.
SUN VISORS
To provide maximum protection for the driver and officer, two (2) padded sun visors measuring
19"L x 7-1/2"W, with shock retainers, shall be recess mounted in the cab overhead on each side.
MAP BOOK STORAGE
A map book compartment shall be provided for vertical storage of three (3) 2" 3-ring binders, which
shall be front loaded. The storage compartment shall be constructed from 1/8" aluminum which shall be
painted with textured paint, matching the interior color of the cab.
INTERIOR COMPARTMENT CAB
One (1) fully enclosed, full width compartment approximately 10" deep x 8" high mounted to the
cab ceiling at the rear wall. Compartment made of 1/8" aluminum with two (2) aluminum hinged doors with
latch and gas spring stay arm. Doors to be of equal size and hinged at top. Bottom front edge to have a
padded vinyl covered bumper to match cab interior.
INTERIOR COMPARTMENT CAB
Two (2) fully enclosed, full width compartment approximately 10" deep x 8" high mounted to the
cab ceiling over the DS and OS rear facing seats. Compartment made of 1/8" aluminum with aluminum
hinged doors with latch and gas spring stay arm. Doors to be of equal size and hinged at top. Bottom front
edge to have a padded vinyl covered bumper to match cab interior.
Allen Volunteer Fire Co., Inc. Tanker Specification
23
Antietam Fire Apparatus, Inc.
ANTENNA INSTALLATION
One (1) customer furnished antenna(s) shall be mounted on the cab roof and shall be located as
noted on the final approval drawing. The antenna(s) shall be furnished to the manufacturer prior to
construction of the custom chassis. The attached antenna wire(s) shall be run to the right side cab dash
area, unless otherwise specified.
ANTENNA INSTALLATION
One (1) antenna mounting base(s) Model #MATM with 17' of coaxial cable shall be provided and
installed on the lower cab roof, behind the light bar. The attached antenna wire(s) shall be run to the right
side cab dash area.
DASH & CENTER CONSOLE
The dash shall be constructed of a vinyl overlaid, ABS custom formed material to create an
ergonomically designed interior to be user friendly and functional for the driver and officer. The instrument
cluster shall be centered in front of the driver and all gauges shall be fitted in a non-glare pewter panel.
All warning lights and indicators shall be located in either the gauge itself or in the warning light
cluster located in the lower center portion of the dash. Each gauge shall be equipped with an international
symbol that is easily recognizable, denoting the system being monitored. Instrumentation shall be backlit
for easy identification.
The transmission gear selector and the spring brake control valve shall be located on the left side
of the center dash assembly, toward the driver for easy access.
There shall be provisions for mounting a switch panel in the center of the dash between the driver
and officer. The top center of the dash assembly shall contain one (1) large removable access door for
access to the main chassis wiring panels and breaker panels.
LOWER RIGHT AUXILIARY SWITCH PANEL
The drivers lower right panel shall contain four (4) multi-function, multiplexed switches. One switch
shall be utilized for panel dimming, one switch shall control the fast idle, one switch shall control the head
lights and the last switch shall select either the air horn or electric horn. These switches shall be clearly
labeled with integral LED indicators.
The lower portion of this panel can be used for the installation of up to five (5) guarded type rocker
switches. Examples of the switches that shall be installed in this area are automatic chains, fan clutch
over-ride, ATC mud-snow, inter-axle diff lock, electric fuel pump, all wheel drive, etc.
DRIVERS DASHBOARD PANEL
The main instrument panel shall be centered in front of the driver and shall be hinged at the bottom
with two ¼ turn latches at the top. The dash panel shall be 1/8” aluminum with an anti-glare, pewter finish
Allen Volunteer Fire Co., Inc. Tanker Specification
24
Antietam Fire Apparatus, Inc.
brushed surface. The drivers dashboard panel shall contain the gauge panel along with an instrument
warning light cluster.
The main instrument panel shall contain ten (10) primary gauges. An ignition and engine start
switch shall be located on a panel to the left upper portion of the driver's side dash panel.
Each gauge shall have a raised glass lens with polished chrome trim ring and be backlit by integral
blue LED's. Each gauge shall be designed with an integral red warning light with a pre-programmed
warning point. Gauges monitoring drive-train component status shall be of the direct data bus type
capable of displaying information broadcast on the J 1939 data-link. Each gauge warning indicator shall
be capable of activating an audible alarm inside the dashboard.
The ten (10) primary gauges shall consist of:










Vehicle speedometer (0-80 mph) with digital odometer
Engine tachometer (0-3000 rpm) with digital hour meter
Engine oil pressure (0-100 psi); low oil pressure warning
Engine coolant temperature (100-280 °F); high engine temp warning
Transmission oil temperature (100-350 °F); high transmission fluid temp warning
Vehicle battery voltage (9-18 VDC); low voltage warning at
Front air system gauge (0-150 psi); low air pressure warning at 65 psi
Rear air system gauge (0-150 psi); low air pressure warning at 65 psi
Fuel level (E-1/2-F); low fuel level warning
Air cleaner restriction gauge (0 - 40), warning at 25"
Additional auxiliary control switches and instruments (if applicable) shall be located within the
center or overhead panel located near the driver's position.


Inter axle lock control switch
Engine Compression Brake Controls
A display shall be provided on the dash for the electrical ES-Key multiplex system. The exact
location shall determined by the totality of instruments and switches on the cab dash. The display shall be
in easy reach of the officer to view information.
INDICATOR CLUSTER
The driver's dashboard panel shall consist of Ametek gauges, an 18 item instrument warning light
cluster and a 16 item, dead front type alarm panel.
This display shall contain the system control unit that collects data from the vehicle data bus
(J1939), analog sensors, and switches throughout the vehicle. This data shall be presented using gauges,
telltales and the two (2) display panels. The warning light display shall include a 2 x 20 dot matrix display,
18 telltales and 2 buttons to navigate through the screen menus.
The LCD dot matrix display shall be a 2 line by 20-character display with each character being 7
dot by 5 dot configuration. FSTN technology shall be used on the display for wide viewing capability. The
module shall be backlit with amber LED's. The unit shall also be supplied with a heater to ensure proper
Allen Volunteer Fire Co., Inc. Tanker Specification
25
Antietam Fire Apparatus, Inc.
operation over the entire 40 to +85 deg. C.
This display contains a series of two (2) screens to provide information about the vehicle. To
control the display of that information, the screens are divided into two (2) menus; one that can be
displayed while the vehicle is in motion and one that can only be accessed when the parking brake is set.
On the Road displays include:



Two (2) configurable displays that can show any of the parameters the unit collects. This includes
odometer, trip information, fuel economy information; all gauge data, and virtually any other data
available on the vehicle that the display has access to, either through the data bus or via analog
inputs.
Two (2) trip displays for miles and hours that are capable of being reset.
Two (2) fuel data screens: shall be provided; one for fuel remaining until empty and one for fuel
economy. The fuel economy display shall be capable of being reset so that average economy over
a predetermined period can be displayed.
The displays that can be accessed when the parking brake is set include:





Engine hours as maintained by the engine ECU
Service Alarm screens to report miles to next service or miles past required service. These screens
shall allow the operator to choose the length of the service interval and shall have the ability to
reset it.
Message screens with warning messages the display has collected during the current ignition
cycle. These screens shall be divided into configured warnings such as “Low Air Pressure” and the
data bus faults reported by ECU's on the vehicle. Both lists shall allow the operator to review the
last 12 events that occurred on the vehicle for maintenance and troubleshooting purposes.
Diagnostic screens shall test the instrumentation system to verify it is working correctly.
Setup screens shall be used to select either English or metric display. They shall also allow the
operator to choose the data that shall be displayed by the configurable on-the-road screens.
The system shall be configured with user defined warning messages such as Low Air Pressure or
High Coolant Temperature. When these events occur the warning message shall come up on the screen
and can be accompanied by a buzzer. The messages shall be prioritized so the most important messages
are always displayed. Whether the message can be dismissed by pressing a button shall be configurable.
Messages that have been dismissed but are still active shall be retained in the message screens for
review until the inition is turned off. Listed below are the defined telltales and their indicators.











"Right And Left Directional" arrows
"Ignition ON" Indicator
"Hi Beam" indicator
"Battery ON" indicator
"Parking Brake ON" indicator
"Check Transmission" indicator
"Cab Not Latched" indicator
"Stop Engine" indicator
"Check Engine" indicator
"ABS Warning" indicator
"Low Coolant Level"
(green in color)
(amber in color)
(blue in color)
(green in color)
(red in color)
(amber in color)
(red in color)
(red in color)
(amber in color)
(red in color)
(red in color)
Allen Volunteer Fire Co., Inc. Tanker Specification
26
Antietam Fire Apparatus, Inc.









"Fuel Restriction" indicator
"Water In Fuel" indicator
"Fasten Seat Belts" indicator
"Fast Idle" Indicator
"Do Not Move Truck" indicator
"DPF Regeneration"
"Exhaust High Temperature"
"Engine Diagnostic Fault"
"Retarder On"
(amber in color)
(amber in color)
(red in color)
(amber in color)
(red in color)
(amber in color)
(amber in color)
(amber in color)
(green in color)
Listed below are indicators that may be included, depending upon the vehicle configuration:















"Wait To Start" indicator
(amber in color)
"Exhaust System Fault"
(amber in color)
"Topps System Fault"
(amber in color)
"Lube System Active"
(amber in color)
"Jacks Not Stowed"
(red in color)
"PTO Engaged"
(green in color)
"Inter Axle Lock"
(amber in color)
"4x4"
(green in color)
"Driver Controlled Diff Lock"
(green in color)
"Ok to Pump"
(green in color)
"Auto Traction Control"
(amber in color)
"Retarder Active"
(amber in color)
"Auxiliary Brake Active"
(amber in color)
"Inter Axle Lock" indicator
"Low Engine Coolant" indicator light and alarm
PUMP SHIFT CONTROL
The pump shift control and pump engaged indicator light shall be mounted in the driver's lower left
panel. This control shall be equipped with a mechanical type lock to prevent inadvertent activation or deactivation. The lever positions and indicator light shall be clearly marked.
OFFICER DASH
There shall be a flat surface area in front of the officer.
CENTER OVERHEAD PANEL
An overhead console with a removable pewter panel shall be provided on the cab roof between the
driver and officer to permit installation of cab stereo, intercom systems, arrow stick controls, etc. The
overhead console shall be approximately 27" wide x 4" high x 13" deep and shall be painted to match the
interior of the cab. The overhead console shall not obstruct the driver's vision through the officer's side
window.
Allen Volunteer Fire Co., Inc. Tanker Specification
27
Antietam Fire Apparatus, Inc.
CLIMATE CONTROL SYSTEM
A climate-control system shall be provided for total cab environmental comfort. This system shall
provide heat, cooling and defrost capabilities to various areas in the cab. The system shall consist of two
(2) evaporator units, mounted in the center overhead of the cab. One (1) unit shall provide defrost, air
conditioning and heat for the front of the cab and shall provide heating and cooling for drivers and officers
feet. One (1) unit shall provide heat and air conditioning for the back of the cab.
The ceiling mounted evaporator/heater unit for the front shall include the following:











Dual high output blower.
High efficiency coil that includes "rifled" tubing and oversized header tubes for maximum refrigerant
distribution.
Four (4) 3" diameter, adjustable louvers; two (2) each side of the cab overhead, facing the driver
and officer seat positions.
Four (4) 3" diameter, adjustable defroster louvers positioned above the windshield to provide
optimum coverage.
Four (4) 3" diameter adjustable louvers, one (1) below the driver and officer seat positions and one
(1) under each outboard rear facing crew seat.
Damper controls shall be pneumatically operated to provide air discharge to the windshield, front
overhead air discharge louvers or floor position as required and shall be located above the driver
seat position.
An electric water valve to control the amount of heat.
Fully insulated housing.
BTU: 34,000 A/C
BTU: 50,000 Heat
CFM: 410 @ 13.8 volts
The ceiling mounted evaporator/heater unit for the crew area shall include the following:







Dual high output blower
High efficiency coil which includes, "rifled" tubing and oversized header tubes for maximum
refrigerant distribution
Eight (8) 3" diameter, adjustable louvers positioned to provide optimum coverage.
Fully insulated housing.
BTU: 36,400 A/C
BTU: 52,000 Heat
CFM: 440 @ 13.8 volts
ROOF MOUNT CONDENSER
A 12-volt roof top condenser shall be strategically positioned on the cab roof so as not to interfere
with any emergency lighting systems and shall include the following:



High performance, long life fan assemblies. Fan motors are sealed around housing and shaft
areas.
Condenser and coil design includes rifled tubing for maximum efficiency. Coil is painted black.
Condenser unit includes receiver drier with hi/lo pressure switch.
Allen Volunteer Fire Co., Inc. Tanker Specification
28
Antietam Fire Apparatus, Inc.




Wire harness includes necessary wiring for clutch circuit as well as a separate power relay circuit.
14 gauge mounting brackets
16-gauge condenser frame and fan shroud
16 gauge aluminum cover, E-coated white
Mounting design will enable easy servicing of all components and unit replacement if necessary.
The ceiling mounted evaporator unit shall be covered with an ergonomically designed custom ABS
panel to provide maximum headroom and a pleasing appearance.
CLIMATE CONTROL SWITCHES
The driver’s overhead panel shall contain all controls for the cab climate control system. The
following controls shall be provided: mode selector switch, front fan speed switch, rear fan speed switch,
air conditioning on/off switch, and temperature control dial. All controls shall be clearly labeled,
adequately backlit, and installed in an easily removable panel.
CAB TILT ASSEMBLY
The cab tilt mechanism shall be custom designed for ease of maintenance and shall consist of two
(2) hydraulic cylinders with a maximum lift capacity of 19,625 pounds. Hydraulic lines shall be rated at
20,000 PSI burst pressure. Each cylinder shall have an attached hydraulic locking mechanism, in the
event of a hydraulic failure. Hydraulic cylinders shall be detachable to allow removal of the engine for
major service. A mechanical cylinder stay bar and release shall be provided to insure a positive lock in the
tilted position.
The two (2) rear outboard cab latches shall be of the hydraulic pressure release, automatic relatching type, and provide an automatic positive lock when the cab is lowered. The latch must not
disengage or experience any damage when subjected to a pull apart tensile load of 6,000 lbs. The
hydraulic pressure required to unlock the latch shall not exceed 550 PSI. The latch shall withstand 5,000
PSI without leaks or damage and withstand 1,000 continuous cycles of operation under a load of 1,000 lbs
at liftoff. The tilt pump shall be electric over hydraulic type, with a pressure rating of not less than 4,000
PSI. Additionally, the cab tilt device shall be both electrically and hydraulically interlocked to prevent
inadvertent activation of the cab tilt system.

A "CAB NOT LATCHED" indicator shall be provided in the cab dash-warning cluster.
A dual switch control system shall be provided for the cab tilt, located on the passenger side pump
panel. System shall consist of a three (3) position toggle switch along with a rubber covered push button
switch.
CHASSIS FRAME ASSEMBLY
The chassis frame shall be fabricated in its entirety in the factory of the apparatus manufacturer.
This shall prevent any split responsibility in warranty or service.
Allen Volunteer Fire Co., Inc. Tanker Specification
29
Antietam Fire Apparatus, Inc.
The frame shall consist of two (2) channels fastened together by cross members. All structural
fasteners used in the frame shall be Grade 8 hardware. Hardened steel washers shall be used under all
bolt heads and nuts to avoid stress concentrations. Top flange shall be free of bolt heads. All spring
hangers shall be machined steel castings. Weldment type chassis and the use of Huck bolts shall not be
acceptable.
Each main frame rail shall be 10-1/4" x 4" x 3/8", fabricated from 110,000 PSI minimum yield steel,
with a minimum section modulus of 17.97 in 4 and a resisting bending moment (RBM) of 1,976,700 inch
pounds.
A full length inner frame liner shall be installed. Total section modulus of each rail, with liner, shall
be 31.20 in 4 and the total resisting bending moment (RBM) shall be 3,432,000 in-lbs, per rail.
Formed frame rails or a fish plated frame shall not be acceptable.
The chassis frame assembly, consisting of frame rails, cross members, axles and steering gear(s),
shall be finish painted before installation of any electrical wiring, fuel system components, or air system
components. All components or brackets fastened to the frame rails shall be cleaned, primed and painted
prior to being attached to the frame rails.
FRONT BUMPER
A 12" high, 101" wide, two (2) ribbed, bright finish stainless steel front bumper shall be provided.
The bumper shall be a wrapped design to match the contour of the front cab sheet.
The bumper shall be extended 24" with a polished aluminum tread plate gravel shield enclosing the
top and ends.
STORAGE WELL - CENTER
One (1) storage well constructed of 1/8" aluminum shall be installed in the gravel shield. This
storage well shall be center mounted between the chassis frame rails. The bottom of the storage well shall
have a minimum of four (4) drain holes.
The center front bumper hose well shall be furnished with Velcro straps to secure the hose stored
in the well. The straps shall be attached to each side of the hose well with stainless steel footman loops.
STORAGE WELL - DRIVER SIDE
One (1) storage well constructed of 1/8" aluminum shall be installed in the gravel shield. This
storage well shall be located on the driver side of the bumper extension. The bottom of the storage well
shall have a minimum of four (4) drain holes.
The driver side front bumper hose well shall be furnished with Velcro straps to secure the hose
stored in the well. The straps shall be attached to each side of the hose well with stainless steel footman
loops.
Allen Volunteer Fire Co., Inc. Tanker Specification
30
Antietam Fire Apparatus, Inc.
STORAGE WELL - OFFICER SIDE
One (1) storage well constructed of 1/8" aluminum shall be installed in the gravel shield. This
storage well shall be located on the officer side of the bumper extension. The bottom of the storage well
shall have a minimum of four (4) drain holes.
One (1) hinged, latched, aluminum tread plate cover shall be installed on the storage well located
in the officer side of the bumper extension.
FRONT TOW HOOKS
Two (2) chrome plated tow hooks shall be provided, mounted below the front bumper attached
directly to the frame. The tow eyes shall be fastened with grade 8 bolts and nuts.
FRONT AXLE
Front axle shall be a Meritor MFS-20-133 A-N, includes low friction "Easy Steer" bushing
technology for maximum steering ease and longer life.
The front axle shall be rated at 22,500 lbs. (Minimum)
FRONT DISC BRAKES
Meritor EX-225 H, 17" disc brakes shall be provided for the front axle. The front brakes will be full
air actuated with automatic slack adjustment.
FRONT SUSPENSION
Front suspension shall be progressive rate front leaf springs. The spring shall be permanently
pinned at the front and have a shackle double pinned mounting at the rear. Suspensions allowing the
spring to float freely at the ends without a permanent pin shall not be acceptable.
The front leaf springs shall have a minimum of 10 leaves, a minimum length of 51", and a minimum
width of 3-1/2". The capacity at ground shall be 23,000 lbs. All springs shall be of center bolt design. Cup
center springs shall not be acceptable. All spring pins shall be positively restrained from rotating in
brackets and shackles.
FRONT SHOCK ABSORBERS
The front suspension system shall be equipped with Monroe, model "Magnum - 70", double acting
hydraulic shock absorbers. Shock absorbers to have a minimum bore of 1.38" and an outside diameter of
approximately 3-1/4".
Allen Volunteer Fire Co., Inc. Tanker Specification
31
Antietam Fire Apparatus, Inc.
REAR AXLE
Rear axle assembly shall be a tandem, Meritor RT-46-160 single reduction with a capacity of
48,000 lbs. Axles shall have a gear reduction as required.
A driver controlled inner axle lock for RT series axles shall be provided on the cab dash within easy
reach of the driver.
Oil seals shall be provided as standard equipment.
REAR DISC BRAKES
Meritor EX-225, 17" disc brakes shall be provided for the rear tandem axles. The rear brakes will
be full air actuated with automatic slack adjustment.
REAR AXLE TOP SPEED
The rear axle/s shall be geared for a vehicle top speed in accordance with NFPA sections 4.15.2
and 4.15.3.
Units with GVWR over 26,000 pounds shall be limited to 68 mph. If the combined tank capacity is
over 1250 gallons of foam and water or the GVWR is over 50,000 pounds, the vehicle top speed shall be
limited to 60 mph or the fire service rating of the tires, whichever is lower.
REAR SUSPENSION
The rear suspension shall be a Hendrickson model #RT-503 with a 52" steel-walking beam and a
ten (10) leaf spring pack as designed by Hendrickson Manufacturing Company. The suspension shall
have a weight rating equal to the rear axle weight rating up to 48,000 pounds. Designs allowing the main
pack to float are not acceptable.
BRAKE SYSTEM
A dual circuit, air operated braking system, meeting the design and performance requirements of
FMVSS-121 and the operating test requirements of NFPA 1901 current edition shall be installed. It shall
be direct air type with dual air treadle in the cab. The system shall be powered by an engine mounted,
gear driven air compressor protected by a heated air dryer.
The air system shall be plumbed with reinforced, air brake tubing/hose in conformance to SAE J
844-94, Type B and U.S.D.O.T. standards. The compressor discharge shall be plumbed with stainless
steel braided hose lines with a Teflon lining. Nylon airlines shall be enclosed in high temperature
convoluted loom run along the inside frame rails, secured with non-conductive, corrosion resistant
strapping mounted with standoff fasteners. Cord reinforced rubber hose lines with brass fittings shall be
installed from frame rail to axle mounted air connections.
The air system shall provide a rapid air build-up feature and low-pressure protection valve with light
Allen Volunteer Fire Co., Inc. Tanker Specification
32
Antietam Fire Apparatus, Inc.
and buzzer, designed to meet the requirements of NFPA 1901, current edition.
ABS SYSTEM
An Anti-Skid Braking System (ABS) shall be provided to improve braking control and reduce
stopping distance. This braking system shall be fitted to all of the axles. All electrical connections shall be
environmentally sealed, water, weatherproof, and vibration resistant.
The system shall constantly monitor wheel behavior during braking. Sensors on each wheel shall
transmit wheel speed data to an electronic processor which shall sense approaching wheel lock causing
instant brake pressure modulation up to 5 times per second in order to prevent wheel lockup. Each wheel
shall be individually controlled.
To improve service trouble shooting, provisions in the system for an optional diagnostic tester shall
be provided. The system shall test itself each time the vehicle is started. A dash-mounted light shall go
out once the vehicle has attained 4 mph after successful ABS start-up To improve field performance, the
system shall be equipped with a dual circuit design. The system circuits shall be configured in a diagonal
pattern. Should a malfunction occur, the defective circuit shall revert to normal braking action. A warning
light shall signal malfunction to the operator. The system shall consist of a wheel mounted toothed ring,
sensor, sensor clip, electronic control unit and solenoid control valve.
The sensor clip shall hold the sensor in close proximity to the toothed ring. An inductive sensor
consisting of a permanent magnet with a round pole pin and coil shall produce an alternating current with
a frequency proportional to wheel speed. The unit shall be sealed, corrosion resistant and protected from
electromagnetic interference. The electronic control unit shall monitor the speed of each wheel. A
deviation shall be corrected by cyclical brake application and release. If a malfunction occurs, the
defective circuit shall signal the operator and the malfunctioning portion of the system shall shut down.
The system shall be installed in a diagonal pattern for side-to-side control. The system shall insure that
each wheel is braking to optimum efficiency up to 5 times a second.
The system shall also control application of the auxiliary engine exhaust or drive line brakes to
prevent wheel lock.
This system shall have a three (3) year or 300,000 mile parts and labor warranty as provided by
Meritor Wabco Vehicle Control Systems.
BRAKE AIR RESERVOIRS
There shall be a minimum of four (4) air reservoirs and be installed in conformance with best
automotive practices.
Reservoir capacity total shall be a minimum of 7,355 cu. in.
Each additional air tank shall be equipped with an automatic moisture ejector.
For ease of daily maintenance, each air system reservoir shall be equipped with a brass 1/4 turn
drain valve.
Allen Volunteer Fire Co., Inc. Tanker Specification
33
Antietam Fire Apparatus, Inc.
AIR DRYER
A Bendix #AD-9 heated air dryer shall be furnished. An automatic moisture ejector on the primary,
or wet tank, shall also be furnished
AIR LINES
The entire chassis air system shall be plumbed utilizing reinforced, Synflex air lines. All of the
airlines shall be color coded to correspond with an air system schematic and shall be adequately protected
from heat and chafing.
AIR COMPRESSOR
Air compressor shall be a Wabco brand, minimum of 18.7 cubic feet per minute capacity. Air brake
system shall be the quick build up type. The air compressor discharge line shall be stainless steel braid
reinforced Teflon hose.
A pressure protection valve shall be installed to prevent the use of air horns or other air operated
devices should the air system pressure drop below 80 psi (552 kPa).
The chassis air system shall meet NFPA 1901, latest edition for rapid air pressure build-up within
sixty (60) seconds from a completely discharged air system. This system shall provide sufficient air
pressure so that the apparatus has no brake drag and is able to stop under the intended operating
conditions following the sixty (60) seconds build-up time.
BRAKE TREADLE VALVE
A Bendix dual brake treadle valve shall be mounted on the floor in front of the driver. The brake
control shall be positioned to provide unobstructed access and comfort for the driver.
PARKING BRAKE
Parking brake shall be of the spring-actuated type, mounted on the rear axle brake chambers. The
parking brake control shall be mounted on the cab center instrument panel, offset toward the driver. A red
indicator light shall be provided in the driver dash panel that shall illuminate when the parking brake is
applied.
FRONT WHEELS & TIRES
The front wheels shall be 22.5" x 12.25" ten stud, hub piloted polished aluminum disc type.
The aluminum disc front wheels shall be provided with bright nut covers and hub caps.
The front tires shall be Goodyear 425/65R22.5 "20 Ply" tubeless radial G286A-SS on/off road
tread. The tires shall be fire service rated up to 24,400 lbs and shall have a top speed of 68 mph when
Allen Volunteer Fire Co., Inc. Tanker Specification
34
Antietam Fire Apparatus, Inc.
inflated to 120 psi.
Fire Service Rating defined as no more than 50 miles of continuous operation at maximum load, or
without stopping for at least 20 minutes. Emergency vehicle must reduce its speed to no more than 50
mph after the first 50 miles of travel.
Industry load and inflation standards are in a constant state of change. Printed material may not
reflect the latest load and inflation standards.
NOTE: NEVER EXCEED THE MAXIMUM AIR PRESSURE LIMITATION
REAR WHEELS & TIRES
The tandem rear axle wheels shall be 22.5" x 9" ten stud, hub piloted disc type. The inner wheels
shall be painted steel, the outer wheels shall be polished aluminum.
The tandem rear aluminum disc wheels shall be provided with bright nut covers and hub caps.
The rear tires shall be Goodyear 315/80R22.5 "18 Ply" tubeless radial Regional RHD traction
tread. The tires shall be fire service rated up to 64,000lbs and shall have a top speed of 75 mph when
inflated to 125 psi.
Fire Service Rating defined as no more than 50 miles of continuous operation at maximum load, or
without stopping for at least 20 minutes. Emergency vehicle must reduce its speed to no more than 50
mph after the first 50 miles of travel.
Industry load and inflation standards are in a constant state of change. Printed material may not
reflect the latest load and inflation standards.
NOTE: NEVER EXCEED THE MAXIMUM AIR PRESSURE LIMITATION
TIRE PRESSURE MONITORING DEVICES
Each tire shall be equipped with an air pressure indicator cap on the valve stem. Each cap shall
have a visual indicator to show if the tire is correctly inflated.
ENGINE
Engine shall be a Cummins, Model ISM 500, diesel, turbo-charged, per the following specifications.





Max. Horsepower
Governed Speed
Peak Torque
Cylinders
Operating Cycles
500 HP @ 1900 RPM
2100 RPM
1550 lb. ft. @ 1200 RPM
Six (6)
Four (4)
Allen Volunteer Fire Co., Inc. Tanker Specification
35
Antietam Fire Apparatus, Inc.





Bore & Stroke
Displacement
Compression Ratio
Governor Type
Drive line Size
4. 9 x 5.8 in.
661 cu. in.
16.1:1
Limiting Speed
1810 Series
Engine oil filters shall be engine manufacturers branded or approved equal. Engine oil filters shall
be accessible for ease of service and replacement.
A fuel/water separator shall be provided.
The manufacturer shall be able to furnish proof of engine installation approval by the engine
manufacturer.
ENGINE WARRANTY
The Cummins engine shall be warranted for a period of five (5) years or 100,000 miles, whichever
occurs first.
COOLING/RADIATOR
Radiator shall be brass with bolted steel top and bottom tanks. The cooling system shall be
designed for a maximum of fifteen (15) PSI operation. There shall be a sight glass in the radiator to check
the coolant level without removing the radiator cap. The core construction shall be tube and fin with three
(3) tube rows, 273 total core tubes, and fourteen (14) fins per inch.
Engine coolant shall be treated with supplementary coolant additives (SCA's) required by the
engine manufacturer. Engine coolant shall provide anti-freeze protection to -30° F. The mixture shall be
per the engine manufacture's specifications.
A transmission oil to liquid cooler shall be furnished.
Core area shall be a minimum of 1375 square inches (39 H x 35.25W).
RADIATOR SKID PLATE
The radiator installation shall include a removable heavy-duty radiator skid plate to protect the
radiator from debris or obstructions under the chassis. The skid plate shall be designed so the angle of
approach is not affected.
CHARGE AIR COOLER
The charge air cooler shall be constructed of aluminum with cast aluminum side tanks. The cooler
shall have a frontal core size of 957 square inches, seven (7) fins per inch, and forty eight (48) core tubes.
The charge air cooler shall be mounted directly ahead of the radiator and to the radiator headers.
Rubber isolators shall be used at the mounting points to reduce transmission of vibrations.
Allen Volunteer Fire Co., Inc. Tanker Specification
36
Antietam Fire Apparatus, Inc.
The piping between the charge air cooler and engine shall use heavy duty hoses with stainless
steel bands. Bands are used to maintain the shape of the hose during changing turbo boost pressures.
The hoses shall be attached with stainless steel constant torque hose clamps.
COOLING SYSTEM FAN
The engine cooling system shall incorporate a heavy duty fan, installed on the engine and include
a shroud.
The fan shall be equipped with an air operated clutch fan, which shall activate at a pre-determined
temperature range.
Re-circulation shields shall be installed to ensure that air which has passed through the radiator is
not drawn through it again.
Heavy duty silicone heater and coolant hoses shall be furnished for the heater and coolant system.
All coolant hoses shall be equipped with constant torque type hose clamps. All integral hoses supplied
with the engine shall be as supplied by the engine manufacturer.
LOW COOLANT INDICATOR LIGHT AND ALARM
A low engine coolant indicator light located in the dash instrument panel shall be provided. An
audible alarm shall be provided to warn of the low coolant condition.
ENGINE BRAKE
An engine compression brake shall be furnished for increased braking capabilities. Controls shall
be as provided by the engine manufacturer and shall be activated by releasing the throttle pedal to the idle
position.
The engine compression brake shall have dash mounted control switches to turn the brake on or
off as well as to control the operational level of the brake.
The engine brake shall be wired in such a manner so as to illuminate the chassis brake lights when
the engine brake is engaged and operating.
The engine brake shall be interlocked with the PTO operation and shall automatically disengage
any time the apparatus is operating with the PTO active.
ENGINE FAST IDLE
A fast idle for the electronic controlled engine shall be provided. The fast idle shall be controlled by
an ON/OFF switch on the dash.
An electronic interlock system shall prevent the fast idle from operating unless the transmission is
Allen Volunteer Fire Co., Inc. Tanker Specification
37
Antietam Fire Apparatus, Inc.
in "Neutral" (or "Park" if so equipped) and the parking brake is fully engaged. If the fast idle control is used
in conjunction with a specified engine/transmission driven component or accessory, the fast idle control
shall be properly interlocked with the engagement of the specified component or accessory.
AIR CLEANER
An engine air cleaner shall be provided. Air cleaner shall include a dry type element. Air cleaner
shall be installed in accordance with the engine manufacturer's recommendations. The air cleaner shall be
located to the rear of the engine, with streamline air pipes and hump hose connections from the inlet to the
air cleaner and from the air cleaner to the turbo. The air cleaner shall be easily accessible when the cab is
tilted.
Air cleaners mounted on the side or near the bottom of the cab shall not be acceptable. [NO
EXCEPTIONS]
SPARK ARRESTOR
A spark arrestor shall be installed in the chassis air intake system. This arrestor shall be mounted
behind the intake grille to filter out airborne embers. The spark arrestor housing must be easily accessible
when the cab is tilted.
ACCELERATOR CONTROL
A floor mount accelerator pedal shall be installed on the floor in front of the driver. The pedal shall
be positioned for comfort with ample space for fire boots and adequate clearance from the brake pedal
control.
TRANSMISSION
An Allison World Transmission, Model 4000 EVS electronically controlled, automatic transmission
shall be provided. Transmission specifications shall be as follows:







Max. Gross Input Power
Max. Gross Input Torque
Input Speed (Range)
Shift Calibrations
Direct Gear (Pumping)
Direct Gear Ratio
Overdrive Ratio
600 HP
1850 lb. ft.
1700- 2300 RPM
5 Speed (6th not avail. for fire appl.)
4th (Lock-up)
1.00:1
0.74:1
Transmission installation shall be in accordance with the transmission manufacturer's specification.
The transmission shall be readily and easily removable for repairs or replacement.
An illuminated, touch-pad type shift control shall be mounted in the cab, convenient to the driver.
Shift control shall be approved by the transmission manufacturer.
Allen Volunteer Fire Co., Inc. Tanker Specification
38
Antietam Fire Apparatus, Inc.
TRANSMISSION OIL LEVEL SENSOR
The transmission shall be equipped with the oil level sensor (OLS); this sensor shall allow the
operator to obtain an indication of the fluid level from the shift selector. The sensor display shall provide
the following checks, correct fluid level, low fluid level and high fluid level.
PARK TO NEUTRAL
The transmission, upon application of the parking brake, shall automatically shift into neutral.
TRANSMISSION FLUID
Dextron transmission fluid shall be utilized to fill the 3000 EVS transmission.
DRIVE LINES
Drive lines shall be Dana (Spicer) 1810 heavy duty series or equal, with "glide coat" splines on all
slip shafts. The chassis manufacturer shall utilize an electronic type balancing machine to statically and
dynamically balance all drive shafts. The chassis manufacturer shall be able to provide proof of
compliance with all drive shaft manufacturer's standards and specifications. (No Exceptions)
EXHAUST SYSTEM
The exhaust system shall be installed in accordance with the engine manufacturer's requirements
and meet all Cummins Non - DPF system requirements and State noise level requirements. Exhaust
system components shall be securely mounted and easily removable.
The muffler shall be sized to be compatible with the engine exhaust discharge.
Exhaust tubing shall be a minimum of 16 gauge material. Any flexible exhaust tubing shall be HDT
stainless steel type. To minimize heat build-up, exhaust tubing within the engine compartment shall be
wrapped with an insulating material. Exhaust shall be wrapped from the turbocharger to the entrance of
the muffler. Material shall be held in place with worm gear type clamps.
The exhaust tailpipe extending from the muffler (DPF) to the side of the vehicle shall be
constructed from 16-gauge aluminized steel tubing. The exhaust discharge shall be on the right side of
the apparatus forward of the rear axle.
FUEL TANK
Fuel tank shall be a minimum of sixty-five (65) gallon capacity. It shall have a minimum fuel filler
neck of 2" ID. A 1/2" minimum diameter drain plug shall be provided. The tank shall be fabricated from
hot rolled, pickled and oiled steel. Provisions for an additional feed line and fuel level float shall be
provided for apparatus manufacturer's use.
Allen Volunteer Fire Co., Inc. Tanker Specification
39
Antietam Fire Apparatus, Inc.
The fuel tank shall be installed behind the rear wheels between the frame rails.
The fuel tank shall meet all FHWA 393.67 requirements including a fill capacity of 95% of tank
volume.
The fuel lines shall be wire braid reinforced fuel hose. The lines shall be carefully routed and
secured along the inside of the frame rails.
FUEL COOLING SYSTEM
A fuel cooling system shall be provided. The heat exchanger shall be a tube and fin type and shall
be a separate unit. The cooler shall be mounted forward of the radiator and plumbed to the fuel return
line.
FUEL FILTER/WATER SEPARATOR
A Racor heated fuel filter/water separator shall be provided in the fuel system. A "water in fuel"
indicator shall be provided on the dash.
DETROIT DIESEL FUEL PRO 382 FUEL HEATER/WATER SEPARATOR
A Detroit Diesel Fuel Pro 382 combination fuel heater/water separator and fuel filter shall be
provided. The 382E shall replace the secondary fuel filter on the engine. The separator shall be installed
between the fuel tank and the inlet of the fuel pump, the see through isoplast cover allows instant visual
checking of the fuel filters condition. A "water in fuel" indicator shall be provided on the dash.
SECONDARY ELECTRIC FUEL PUMP
In addition to the primary fuel pump, a secondary electric fuel pump for re-priming shall be
furnished in the main fuel line. A labeled control switch shall be provided on the main dash panel.
FUEL POCKET
A fuel fill shall be provided in the left side rear wheel well area. A Cast Products heavy duty cast
aluminum spring loaded hinged fill door shall be provided.
A label indicating "DIESEL FUEL ONLY" shall be provided adjacent to the fuel fill.
DUAL POWER STEERING
A DUAL power steering system shall be provided utilizing a Sheppard model #M110 main steering
gear on the driver side of the chassis and a duplicate Sheppard model #M110 power steering gear on the
officer side of the chassis. The power steering gear on the officer side of the chassis will increase
performance in turning the officer side wheel assembly, reducing loads and forces on the main gear and
Allen Volunteer Fire Co., Inc. Tanker Specification
40
Antietam Fire Apparatus, Inc.
components as well as providing redundancy in the event of a steering failure. The steering system shall
be designed to maximize the turning capabilities of the front axle no matter the rating and tire size. The
use of a power assist cylinder on the officer side of the chassis is NOT ACCEPTABLE.
The system shall be designed utilizing an engine driven hydraulic pump, with a maximum
operating pressure of 2000 PSI. Steering design shall permit a maximum of 5.6 turns from stop to stop.
Steering system components shall be mounted in accordance with the steering gear manufacturer's
instructions.
STEERING WHEEL
The steering wheel shall be vinyl padded, minimum 18" diameter, with a center hub mounted horn
button. There shall be a self-canceling, directional signal lever and a traffic hazard switch on the steering
column. The high beam activator shall be controlled by pulling the directional signal lever toward the
driver.
The steering column shall have a separate lever control for tilting and telescoping capability.
ROAD SAFETY KIT
A road safety kit shall be furnished with the following equipment:


2 1/2 lb. B-C fire extinguisher
Triangle safety reflectors
Allen Volunteer Fire Co., Inc. Tanker Specification
41
Antietam Fire Apparatus, Inc.
CHASSIS ELECTRICAL SYSTEM
All electrical wiring in the chassis shall be SXL cross link insulated type. Wiring is to be color coded
and include function codes every three (3) inches on both sides. Wiring harnesses shall be routed in
protective, heat resistant loom, securely and neatly installed. Two (2) power distribution centers shall be
provided in central locations for greater accessibility. The power distribution centers shall contain
automatic thermal self resetting breakers, power control relays, flashers, diode modules, daytime driving
light module, and engine and transmission data links. All breakers and relays shall have a capacity
substantially greater than the expected load on the related circuit, thus ensuring long component life.
Power distribution centers shall be composed of a system of interlocking plastic modules for ease of
custom construction.
The power distribution centers shall be function oriented. The first is to control major truck function.
The second control center shall enable overhead switching and interior operations. Each module shall be
single function coded and labeled to aid in troubleshooting. The centers shall also have accessory
breakers and relays for future installations. All harnesses and power distribution centers shall be
electrically tested prior to installation to ensure the highest system reliability.
All external harness interfaces shall be of a triple seal type connection to ensure a proper
connection. The cab/chassis and the chassis/body connection points shall be mounted in accessible
locations. Complete chassis wiring schematics shall be supplied with the apparatus.
WIRING HARNESS DESCRIPTION
The wiring harness contained on the chassis shall be designed to utilize wires of stranded copper
or copper alloy of a gauge rated to carry 125% of maximum current for which the circuit is protected
without exceeding 10% voltage drop across the circuit. Wiring must be uniquely identified by color code or
circuit function code, labeled at a minimum of every three (3) inches. The identification of the wiring shall
be referenced on a wiring diagram. All wires conform to SAEJ1127 (Battery Cable), SAEJ1128 (Low
Tension Primary Cable), SAEJ1560 (Low Tension Thin Wall Primary Cable).
The covering of harnesses shall be moisture resistant loom with a minimum rating of 289 Degrees
Fahrenheit and a flammability rating of VW-1 as defined in UL62. The covering of jacketed cable shall
have a minimum rating of 289 degree Fahrenheit.
All harnesses must be securely installed in areas protected against heat, liquid contaminants and
damage. The harness connections and terminations shall use a method that provides a positive
mechanical and electrical connection and are in accordance with the device manufacturer's instructions.
No connections within the harness may utilize wire nut, insulation displacement, or insulation piercing
components.
All circuits shall conform to SAEJ1292. All circuits must be provided with low voltage over current
protective devices. These devices shall be readily accessible and protected against heat in excess of
component rating, mechanical damage, and water spray. Star washers shall not used for ground
connections.
Allen Volunteer Fire Co., Inc. Tanker Specification
42
Antietam Fire Apparatus, Inc.
DIRECT GROUNDING STRAPS
Direct grounding straps shall be mounted to the following areas; frame to cab, frame to body and
frame to pump enclosure.
All exposed electrical connections shall be coated with "Z-Guard 8000" to prevent corrosion.
EMI/RFI PROTECTION
The apparatus shall incorporate the latest designs in the electrical system with state of the art
components to insure that radiated and conducted electromagnetic interference (EMI) and radio frequency
interference (RFI) emissions are suppressed at the source
The apparatus proposed shall have the ability to operate in the environment typically found in fire
ground operations with no adverse effects from EMI/RFI.
EMI/RFI susceptibility is controlled by utilizing components that are fully protected and wiring that
utilizes shielding and loop back grounds where required. The apparatus shall be bonded through wire
braided ground straps. Relays and solenoids that are suspect to generating spurious electromagnetic
radiation are diode protected to prevent transient voltage spikes
In order to fully prevent the radio frequency interference the purchaser may be requested to
provide a listing of the type, power output, and frequencies of all radio and bio medical equipment that is
proposed to be used on the apparatus.
12 VOLT ELECTRICAL SYSTEM TESTING
The apparatus low voltage electrical system shall be tested and certified by the apparatus
manufacture. The certification shall be provided with the apparatus. All tests shall be performed with air
temperature between 0°F and 100°F.
The following three (3) tests shall be performed in order. Before each test, the batteries shall be
fully charged.
TEST #1-RESERVE CAPACITY TEST
The engine shall be started and kept running until the engine and engine compartment
temperatures are stabilized at normal operating temperatures and the battery system is fully charged. The
engine shall be shut off and the minimum continuous electrical load shall be activated for 10 minutes. All
electrical loads shall be turned off prior to attempting to restart the engine. The battery system shall then
be capable of restarting the engine. Failure to restart the engine shall be considered a test failure.
TEST #2-ALTERNATOR PERFORMANCE TEST AT IDLE
The minimum continuous electrical load shall be activated with the engine running at idle speed.
The engine temperature shall be stabilized at normal operating temperature. The battery system shall be
tested to detect the presence of battery discharge current. The detection of battery discharge current shall
be considered a test failure.
Allen Volunteer Fire Co., Inc. Tanker Specification
43
Antietam Fire Apparatus, Inc.
TEST #3-ALTERNATOR PERFORMANCE TEST AT FULL LOAD
The total continuous electrical load shall be activated with the engine running up to the engine
manufacturers governed speed. The test duration shall be a minimum of 2 hours. Activation of the load
management system shall be permitted during this test. However, an alarm sounded due to excessive
battery discharge, as detected by the system, or a system voltage of less than 11.7 volts DC for a 12 volt
system, for more than 120 seconds, shall be considered a test failure.
LOW VOLTAGE ALARM TEST
Following completion of the preceding tests, the engine shall be shut off. The total continuous
electrical load shall be activated and shall continue to be applied until the excessive battery discharge
alarm is activated.
The battery voltage shall be measured at the battery terminals. With the load still applied, a
reading of less than 11.7 volts shall be considered a test failure. The battery system shall then be able to
restart the engine.
At time of delivery, documentation shall be provided with the following information:


Documentation of the electrical system performance test
A written load analysis of the following;
 Nameplate rating of the alternator
 Alternator rating at idle while meeting the minimum continuous electrical load
 Each component load comprising the minimum continuous electrical load.
 Additional loads that, when added to the minimum continuous load, determine the total
connected load.
 Each individual intermittent load.
ELECTRICAL MANAGEMENT SYSTEM
A Class 1 ES-Key Electrical Management System shall be utilized on the chassis for all functions
applicable. The system shall consist of the following components:
A display shall be mounted in the center cab dashboard panel that shall serve as an informational,
status and diagnostic view panel for the vehicles electrical system.
A modem with a RS232 computer interface and standard telephone jack used to not only program
the multiplex system but also serve as a factory direct gateway into the vehicle from any Class 1 multiplex
authorized service facility.
A Universal System Manager (USM), which acts as the main controlling component of the
multiplexing system shall be provided and factory programmed to DOT, NFPA, SAE, the apparatus
manufacturer's and XYZ Fire Department specifications. The programming shall be done by the apparatus
manufacturer's engineering department. The ES-Key system installation shall comply with SAE J 551
requirements regarding Electromagnetic and Radio Frequency interference (EMI, RFI), as well as utilize
components and wiring practices that insure the system is protected against corrosion, excessive
Allen Volunteer Fire Co., Inc. Tanker Specification
44
Antietam Fire Apparatus, Inc.
temperatures, water, excessive physical, and vibration damage by any equipment installed on the vehicle
at the time of delivery.
A series of Multiplexing Input/Output Modules shall be installed. The Input/Output modules shall
permit the multiplexing system to reduce the amount of wiring and components used as compared to nonmultiplexed apparatus. These modules shall vary in I/O configuration, be waterproof allowing installation
outside of enclosed areas and shall possess individual output internal circuit protection. The modules
shall also have three status indicators visible from a service persons vantage point that shall indicate the
status of the module. In the event a load requires more than 7.5 AMPS of operating current, the module
shall activate a simple relay circuit integral to any of the 3 dillbox assemblies installed in the cab.
DIAGNOSTICS
Diagnostic ports shall be accessible while standing on the ground and located inside the drivers
side door left of the steering column. The diagnostic panel shall allow diagnostic tools such as computers
to connect to various vehicle systems for improved troubleshooting providing a lower cost of ownership.
Diagnostic switches shall allow engine and ABS systems to provide blink codes should a problem exist.
The diagnostic system shall include the following:



Engine diagnostic port
Transmission and ABS diagnostic port
Roll sensor diagnostic port (if applicable)
Additional diagnostic locations under the officers side of the dash.


Engine diagnostic switch (blink codes)
ABS diagnostic switch (blink codes)
VOLTAGE MONITOR SYSTEM
A voltage monitoring system shall be provided to indicate the status of the battery system
connected to the vehicle's electrical load. The system shall provide visual and audible warning when the
system voltage is below or above optimum levels.
The alarm shall activate if the system falls below 11.8 volts DC for more than two (2) minutes.
INDICATOR LIGHT AND ALARM PROVE-OUT SYSTEM
A system shall be provided which automatically tests basic indicator lights and alarms located on
the cab instrument panel.
SEQUENCER
A sequencer shall be provided that automatically activates and deactivates vehicle loads in a
Allen Volunteer Fire Co., Inc. Tanker Specification
45
Antietam Fire Apparatus, Inc.
preset sequence thereby protecting the alternator from power surges. This sequencer operation shall
allow a gradual increase or decrease in alternator output, rather than loading or dumping the entire 12 volt
load to prolong the life of the alternator.
Emergency light sequencing shall operate in conjunction with the emergency master light switch.
When the emergency master switch is activated, the emergency lights shall be activated one by one at
half second intervals. Sequenced emergency light switch indicators shall flash while waiting for activation.
When the emergency master switch is deactivated, the sequencer shall deactivate the warning
light loads in the reverse order.
Rear of cab Air-Conditioning and Heat shall be load managed.
ELECTRICAL HARNESS REQUIREMENT
To ensure dependability, all 12-volt wiring harnesses installed by the apparatus manufacturer shall
conform to the following specifications:












SAE J 1128 - Low tension primary cable
SAE J 1292 - Automobile, truck, truck-tractor, trailer and motor coach wiring
SAE J 163 - Low tension wiring and cable terminals and splice clips
SAE J 2202 - Heavy duty wiring systems for on-highway trucks
NFPA 1901 - Standard for automotive fire apparatus
FMVSS 302 - Flammability of interior materials for passenger cars, multipurpose passenger
vehicles, trucks and buses
SAE J 1939 - Serial communications protocol
SAE J 2030 - Heavy-duty electrical connector performance standard
SAE J 2223 - Connections for on board vehicle electrical wiring harnesses
NEC - National Electrical Code
SAE J 561 - Electrical terminals - Eyelet and spade type
SAE J 928 - Electrical terminals - Pin and receptacle type A
For increased reliability and harness integrity, harnesses shall be routed throughout the cab and
chassis in a manner which allows the harnessing to be laid into it's mounting location. Routing of
harnessing which requires pulling of wires through tubes shall not be allowed.
Wiring shall be run in loom or conduit where exposed, and have grommets or other edge protection
where wires pass through metal. Wire colors shall be integral to each wire insulator and run the entire
length of each wire. Harnessing containing multiple wires and uses a single wire color for all wires shall
not be allowed. Function and number codes shall be continuously imprinted on all wiring harness
conductors at 3.00" intervals. All wiring installed between the cab and into doors shall be protected by a
wire conduit to protect the wiring. Exterior exposed wire connectors shall be positive locking, and
environmentally sealed to withstand elements such as temperature extremes, moisture and automotive
fluids. Electrical wiring and equipment shall be installed utilizing the following guidelines:


All holes made in the roof shall be caulked with silicon (no exception). Large fender washers,
liberally caulked, shall be used when fastening equipment to the underside of the cab roof.
Any electrical component that is installed in an exposed area shall be mounted in a manner that
Allen Volunteer Fire Co., Inc. Tanker Specification
46
Antietam Fire Apparatus, Inc.








shall not allow moisture to accumulate in it. Exposed area shall be defined as any location outside
of the cab or body.
For low cost of ownership, electrical components designed to be removed for maintenance shall be
quickly accessible. For ease of use, a coil of wire shall be provided behind the appliance to allow
them to be pulled away from the mounting area for inspection and service work.
Corrosion preventative compound shall be applied to non-waterproof electrical connectors located
outside of the cab or body. All non-waterproof connections shall re-quire this compound in the plug
to prevent corrosion and for easy separation of the plug.
Any lights containing non-waterproof sockets in a weather-exposed area shall have corrosion
preventative compound added to the socket terminal area.
All electrical terminals in exposed areas shall have protective coating applied completely over the
metal portion of the terminal.
Rubber coated metal clamps shall be used to support wire harnessing and battery cables routed
along the chassis frame rails.
Heat shields shall be used to protect harnessing in areas where high temperatures exist.
Harnessing passing near the engine exhaust shall be protected by a heat shield.
Cab and crew cab harnessing shall not be routed through enclosed metal tubing. Dedicated wire
routing channels shall be used to protect harnessing therefore improving the overall integrity of the
vehicle electrical system. The design of the cab shall allow for easy routing of additional wiring and
easy access to existing wiring.
All standard wiring entering or exiting the cab shall be routed through sealed bulkhead connectors
to protect against water intrusion into the cab.
BATTERY CABLE INSTALLATION
All 12-volt battery cables and battery cable harnessing installed by the apparatus manufacturer
shall conform to the following requirements:






SAE J 1127 - Battery Cable
SAE J 561 - Electrical terminals, eyelets and spade type
SAE J 562 - Nonmetallic loom
SAE J 836 A - Automotive metallurgical joining
SAE J 1292 - Automotive truck, truck-tractor, trailer and motor coach wiring
NFPA 1901 - Standard for automotive fire apparatus
Battery cables and battery cable harnessing shall be installed utilizing the following guidelines:




Splices shall not be allowed on battery cables or battery cable harnesses.
For ease of identification and simplified use, battery cables shall be color coded. All positive
battery cables shall be marked red in color. All negative battery cables shall be black in color.
For ease of identification, all positive battery cable isolated studs throughout the cab and chassis
shall be red in color.
For increased reliability and reduced maintenance, all electrical buss bars located on the exterior of
the apparatus shall be coated to prevent corrosion.
An operational test shall be conducted to ensure that any equipment that is permanently attached
to the electrical system is properly connected and in working order.
Allen Volunteer Fire Co., Inc. Tanker Specification
47
Antietam Fire Apparatus, Inc.
ALTERNATOR
The alternator shall be Leece Neville Model 4890JB, 320 amp, serpentine belt driven unit. The
installation shall include an integral self-diagnostic regulator and rectifier for compact installation.
The alternator installation shall be designed to provide maximum output at engine idle speed to
meet the minimum continuous electrical load of the apparatus as required.
BATTERY SYSTEM
Five (5) Group 31, maintenance free batteries shall be provided. Each battery shall be rated at
925 CCA at 0° F. Reserve capacity shall be 180 minutes. Wiring for the batteries shall be 4/0 welding
type dual path starting cables for SAEJ541.
BATTERY STORAGE
Batteries shall be securely mounted in fixed stainless steel trays located on each side of the
chassis frame. Complete access shall be provided when the cab is fully tilted. Batteries shall be mounted
on non-corrosive matting material.
BATTERY DISCONNECT SWITCH
The chassis batteries shall be wired in parallel to a single 12 volt electrical system, controlled
through a heavy duty, rotary type, master disconnect switch. The master disconnect switch shall be
located within easy access of the driver upon entering or exiting the cab.
BATTERY JUMPER STUDS
A set of Cole Hersee battery jumper studs, Model #46210-02 (red) and #46210-03 (black) shall be
provided to allow the battery system to be jump started or charged from an external source. The studs
shall be located on the driver's side of the chassis and shall be equipped with rubber protector caps.
An additional set of Cole Hersee battery jumper studs, model #46210-02 (red) and #46210-03
(black) shall be provided to allow the battery system to be jump started or charged from an external source
on the officer's side of the vehicle. The studs shall be equipped with rubber protector caps.
120 VOLT SHORELINE CONNECTION - "SUPER 30" AUTO EJECT
One (1) Kussmaul "Super 30" Auto Eject Model 091-159-30-120, automatic, 120 volt, 30 amp
shoreline disconnect shall be provided for the on board, 110 volt battery charging systems.
The disconnect shall be equipped with a three pin female receptacle, which shall automatically
eject the shoreline when the vehicle starter is energized. A label shall be provided indicating voltage and
amperage ratings.
Allen Volunteer Fire Co., Inc. Tanker Specification
48
Antietam Fire Apparatus, Inc.
SHORELINE POWER INLET PLATE
A shoreline power receptacle information plate shall be permanently affixed at or near the power
inlet. The plate shall indicate the following;


Type of Line Voltage
Current Rating in Amps Power Inlet Type (DC or AC)
The Kussmaul auto-eject connection shall be equipped with a Yellow weatherproof cover.
The shoreline receptacle shall be located in the area directly adjacent to the driver's side cab door,
above the side air grille.
BATTERY CHARGER / AIR COMPRESSOR SYSTEM
A Kussmaul Model #091-53-12-REMOTE, "Auto Charge 1200" high output, fully automatic battery
charger shall be provided for maintaining the vehicle battery system. Unique electronic sensing circuits
sense the true battery voltage while eliminating the need for external sense wires. Output current shall be
40 amperes @ 12 volt DC.
A Kussmaul 091-9HP air compressor shall maintain the air pressure in the chassis air brake
system while the vehicle is not in use. The air compressor shall have a rated input at 120 volts AC @ 3.5
amps and an output of 1.4 CFM with a 125 psi max output.
A LED bar graph display shall be located near the shoreline connection to monitor the battery
status.
EMERGENCY SWITCHES
A switch control console shall be provided in the center dash panel between the driver's and
officer's position. This console shall separate the emergency / auxiliary electrical functions from the regular
chassis functions. Eight (8) Class One model #SPS programmable touch pad type switches with integral
indicator lights shall be provided.
A master switch shall be provided, which shall allow pre-setting of emergency light switch and shall
have a red integral indicator light. A primary emergency lighting switch shall be provided, next to the
master switch, along with a total of six (6) load manageable emergency switches. The last remaining
switch shall be a ground light switch. All switches, (other than the master switch), shall have switch
function labeling and an amber integral indicator light.
"LED" CAB INTERIOR LIGHTING
Four (4) Akron 8080-8000-13 interior LED combination red/white dome lights shall be furnished in
the cab, two (2) in the forward section and two (2) in the rear crew section. Each dome light shall have an
integral selector switch. Each dome light shall also activate when the respective, adjacent cab door is
opened.
Allen Volunteer Fire Co., Inc. Tanker Specification
49
Antietam Fire Apparatus, Inc.
A shielded light shall be provided in each side opening, cab door step well. These lights shall
activate with the respective door jamb switch.
CAB MAP LIGHT
A Sunnex, high intensity, goose neck map light shall be furnished and located at the center of the
cab dash.
"DO NOT MOVE APPARATUS" WARNING LIGHT WITH AUDIBLE ALARM
A red flashing warning light with an integral audible alarm, shall be functionally located in the cab to
signal when an unsafe condition is present such as an open cab door or body compartment door, an
extended ladder rack, a deployed stabilizer, an extended light tower or any other device which is opened,
extended or deployed which may cause damage to the apparatus if it is moved.
This light shall be activated through the parking brake switch to signal when the parking brake is
released. This light shall be labeled "DO NOT MOVE APPARATUS WHEN LIGHT IS ON".
CIGARETTE LIGHTER PORT
One (1) 12 volt cigarette lighter style accessory outlet(s) shall be installed in the cab of the truck for
the fire departments accessory devices. The lighter(s) shall be located as directed near the officer's
seating position for devices such as cellular phones.
12 VOLT ACCESSORY CIRCUIT - CAB DASH
A dedicated 12 volt power and ground circuit shall be provided in the cab dash or console as
required. The circuit shall be for future installation of radios or accessories.
SAFETY VISION CAMERA SYSTEM - (2) CAMERAS
A Safety Vision #SV-CLCD-64 rear vision camera system with audio shall be provided to allow the
driver to visually see and hear at the rear and officer's side of the apparatus while in the cab. The system
shall include a flat screen 6.4" color monitor, and two (2) color cameras with microphone and LED
Illuminators, that shall be mounted one (1) at the rear of the vehicle, and one (1) officer's side of the cab.
Cameras: Color SV-600A rear vision camera with microphone. 1/3 CCD imager, 3.0mm Lens,
270,000 pixels, electronic shutter, LED illuminators, waterproof threaded pigtail.
Monitor: Color SV-LCD 68-KIT rear vision monitor. 6.8 LCD screen, speaker, audio and video
adjustment controls, mirror/normal image switch, voltage 10VCD-26 VDC. The system shall also include
a SV-LCD-CB-PKKIT control box. Included cabling is the improved waterproof threaded metallic
connector with rubber o-ring seal. Monitor only. 65' video cable, includes waterproof threaded connector at
camera end.
Allen Volunteer Fire Co., Inc. Tanker Specification
50
Antietam Fire Apparatus, Inc.
NOTE: The system shall operate as follows:


Rear view camera active when truck is in reverse.
Side view camera active when right turn signal is active.
The rear view shall have precedent over the side view camera. The monitor viewing shall
automatically follow the camera switching.
The monitor for the rear vision system shall be mounted ceiling of the cab in easy view of the
driver.
HEADLIGHTS CLUSTER
Two (2) dual, rectangular, halogen headlight modules in bright finish bezels shall be furnished on
the front of the cab. Each head light module shall incorporate an individual low beam and a high beam
headlight. High beam actuation shall be controlled on the turn signal lever.
DAYTIME RUNNING LIGHTS
The chassis head lights shall have integrated circuitry to actuate the low beam headlights at a
maximum of 80 percent of capacity whenever the chassis engine is running.
The daytime running lights shall be interlocked with the parking brake.
SECONDARY DUAL LIGHT MODULE
Two (2) Whelen 60 A 00 TAR arrow shaped, amber LED turn signals shall be provided, one (1) in
each side of the dual light module above the headlights.
The NFPA required, Zone "A" lower warning lights shall be incorporated into each side dual light
module noted above.
DOT MARKER LIGHTS AND REFLECTORS
Five (5) DOT approved Whelen (or equal) Light Emitting Diode (LED) cab marker lamps shall
mounted on the top front edge of the cab roof.
Truck-Lite Model 18 amber LED marker lights/auxiliary turn signals with integral reflectors shall be
provided on the side of the cab above the front wheel well, one (1) each side.
Truck-Lite Model #18 red LED marker lights with integral reflectors shall be provided at the lower
side rear, one (1) each side.
Truck-Lite #60115Y yellow LED side marker and turn lights shall be provided on the apparatus
lower side, forward of rear axle, one (1) each side.
Allen Volunteer Fire Co., Inc. Tanker Specification
51
Antietam Fire Apparatus, Inc.
Truck-Lite Model #19 red LED clearance lights shall be provided on the apparatus rear upper, one
(1) each side at the outermost practical location.
Truck-Lite Model #33740R LED 3-lamp identification bar will be provided on the apparatus rear
center. The lights shall be red in color.
Truck-Lite #98034Y yellow reflectors shall be provided on the apparatus body lower side, as far
forward and low as practical, one (1) each side if the apparatus is 30' long or longer.
Truck-Lite #98034R red reflectors shall be provided on the apparatus rear, one (1) each side at the
outermost practical location.
LICENSE PLATE LIGHT
One (1) license plate light shall be provided above the mounting position of the license plate. The
light shall be clear in color.
TAIL, STOP, TURN AND BACK-UP LIGHTS
Two (2) Whelen 600 series, 4-1/8" x 6-1/2", LED red combination tail and stop lights, shall be
mounted one each side at the rear of the body.
Two (2) Whelen 600 series, 4-1/8" x 6-1/2", LED amber arrow turn signal lights, shall be mounted
one each side, on a vertical plane with the tail/stop lights.
Two (2) Whelen 600 series, 4-1/8" x 6-1/2", white halogen back-up lights, shall be mounted one
each side on a vertical plane with the turn/tail/stop signals. These lights shall activate when the
transmission is placed in reverse gear.
Two (2) Whelen PLAST4V mounting flanges, installed one (1) on each side, shall be provided to
mount the lights described above in one common mounting flange. The fourth opening shall be for the
lower rear warning lights.
CAB STEP LIGHTS
Chrome plated Whelen Model #0AC0EDCR, shielded LED chassis step lights shall be provided
and controlled with marker light actuation. Step lights shall be located to properly illuminate all chassis
access steps and walkway areas.
BODY STEP LIGHTS
Chrome plated Whelen Model #0AC0EDCR, shielded LED body step lights shall be provided and
controlled with marker light actuation. Step lights shall be located to properly illuminate all chassis access
steps and walkway areas.
Allen Volunteer Fire Co., Inc. Tanker Specification
52
Antietam Fire Apparatus, Inc.
DUNNAGE AREA LIGHTING
Two (2) step lights shall be provided in the dunnage area to provide adequate illumination of this
area.
SCENE LIGHTS - REAR OF BODY
Two (2) Whelen 810 series Opti-Scene angled halogen scene lights shall be provided, one on each
side of the rear body panel. The scene lights shall be controlled by a rocker switch in the master warning
light switch console. All scene lights shall be wired through the load management system.
In addition to the cab mounted switch for the rear scene lights, the rear scene lights shall illuminate
when the transmission is placed in reverse gear and the apparatus is operating as an emergency vehicle
(Primary Warning switch on).
GROUND LIGHTS - CAB
One (1) Amdor Luma Bar H2O LED 20" ground light shall be provided under each side cab door
entrance step, four (4) total. The ground lights shall turn on automatically with each respective door jamb
switch and also by a master ground light switch in the warning light switch console.
Each light shall illuminate an area at a minimum 30" outward from the edge of the vehicle.
GROUND LIGHTS - MIDSHIP
One (1) Amdor Luma Bar H2O LED 20" ground light shall be provided under each midship
compartment, total of two (2). The ground lights shall be activated by a master ground light switch in the
cab and shall be wired through the load management system.
GROUND LIGHTS - FRONT BODY
One (1) Amdor Luma Bar H2O LED 20" ground light shall be provided under each front rescue
body corner, two (2) total. The ground lights shall be activated by a master ground light switch in the cab
and shall be wired through the load management system.
GROUND LIGHTS - REAR
One (1) Amdor Luma Bar H2O LED 20" ground light shall be provided under each rear body
corner, two (2) total. The ground lights shall be activated by a master ground light switch in the cab and
shall be wired through the load management system.
GROUND LIGHT SWITCHING
The cab and body ground lights shall be equipped with an activation switch in the cab.
Allen Volunteer Fire Co., Inc. Tanker Specification
53
Antietam Fire Apparatus, Inc.
12 VOLT BODY ELECTRICAL SYSTEM
All electrical lines in the body shall be protected by automatic circuit breakers, conveniently located
to permit ease of service. Flashers, heavy solenoids and other major electrical controls shall be located in
a central area near the circuit breakers.
All lines shall be color and function coded every 3", easy to identify, oversized for the intended
loads and installed in accordance with a detailed diagram. A complete wiring diagram shall be supplied
with the apparatus.
Wiring shall be carefully protected from weather elements and snagging. Heavy duty loom shall be
used for the entire length. Grommets shall be utilized where wiring passes through panels.
In order to minimize the risk of heat damage, wires run in the engine compartment area shall be
carefully installed and suitably protected by the installation of heat resistant shielded loom.
All electrical equipment shall be installed to conform to the latest federal standards as outlined in
NFPA 1901.
BODY ELECTRICAL JUNCTION COMPARTMENT
A weather resistant electric junction compartment shall be provided in the left side lower front
compartment. This compartment shall be recessed through the inside rear wall of the compartment to
provide an easily accessible enclosure to house all of the body wiring junction points, terminal strips,
solenoids, etc. The design of this compartment shall not decrease the storage capacity area of the
compartment in which it is located. A removable panel shall be provided for access to this compartment.
PUMP ENCLOSURE WORK LIGHTS
Work lighting shall be provided inside the pump enclosure providing a minimum of 20 candlepower
illumination.
ENGINE COMPARTMENT WORK LIGHTS
Work lighting shall be provided inside the engine enclosure that will provide a minimum of 20
candlepower illumination.
COMPARTMENT LIGHTS
Each exterior compartment shall have one (1) Weldon model #2630 white dome light. Each light
shall come on automatically when the respective door is opened and the master battery switch is on.
Allen Volunteer Fire Co., Inc. Tanker Specification
54
Antietam Fire Apparatus, Inc.
NFPA LIGHTING PACKAGE
The following warning light package shall include all of the minimum warning light and actuation
requirements for the current revision of the NFPA 1901 Fire Apparatus Standard. The lighting as specified
shall meet the requirements for both "Clearing Right of Way" and "Blocking Right of Way" as noted.
LIGHT PACKAGE ACTUATION CONTROLS
The entire warning light package shall be actuated with a single warning light switch located on the
cab switch panel. The wiring for the warning light package shall engage all of the lights required for
"Clearing Right of Way" mode when the vehicle parking brake is not engaged. An automatic control
system shall be provided to switch the warning lights to the "Blocking Right of Way" mode when the
vehicle parking brake is engaged.
UPPER LEVEL LIGHTING - WHELEN
NFPA ZONE A, UPPER
A Whelen #FNQLED "Edge Freedom", 82" cab roof warning lightbar shall be furnished and rigidly
mounted on top of the cab roof. The lightbar shall be equipped with the following:




Two Front Corner Red Linear LED's
Two Red Forward Facing Linear LED's
Two White Forward Facing Linear LED's
Two Red End Linear LED's
The forward facing clear LED flashers shall be disabled automatically for the "Blocking Right of
Way" mode.
NFPA ZONE C, UPPER
Two (2) Whelen L31HRFN series flashing LED beacon lights shall be mounted one (1) each side
at the rear of the body. A red lens shall be provided on each side.
NFPA ZONES B & D REAR, UPPER
The lighting requirement for this area is covered by the lights noted in Zone "C" - Upper.
NFPA ZONES B & D FRONT, UPPER
The lighting requirement for this area is covered by the lights noted in Zone "A" - Upper.
LOWER LEVEL LIGHTING - WHELEN
NFPA ZONE A, LOWER
Two (2) Whelen #60R02FRR linear super LED light heads shall be provided and installed one (1)
Allen Volunteer Fire Co., Inc. Tanker Specification
55
Antietam Fire Apparatus, Inc.
each side. Each light shall be equipped with a red lens and chrome plated mounting flange.
The lower Zone A warning lights shall be mounted in the custom chassis headlight bezels.
NFPA ZONE C, LOWER
Two (2) Whelen #60R02FRR linear LED light heads shall be provided and installed one (1) each
side directly below the DOT stop, tail, turn and backup lights. Each light shall be equipped with a red lens
and chrome plated mounting flange.
NFPA ZONES B & D FRONT, LOWER
Two (2) Whelen #60R02FRR linear super LED light heads shall be provided and installed one (1)
each side. Each light shall be equipped with a red lens and chrome plated mounting flange.
The lower Zone B & D warning lights shall be mounted on the sides of the custom chassis front
bumper.
NFPA ZONES B & D MIDSHIP, LOWER
Two (2) Whelen #60R02FRR linear super LED light heads shall be provided and installed one (1)
each side. Each light shall be equipped with a red lens and chrome plated mounting flange.
NFPA ZONES B & D REAR, LOWER
Two (2) Whelen #60R02FRR linear super LED light heads shall be provided and installed one (1)
each side. Each light shall be equipped with a red lens and chrome plated mounting flange.
WARNING LIGHT SYSTEM CERTIFICATION
The warning light system(s) specified above shall not exceed a combined total amperage draw of
45 AMPS with all lights activated in either the "Clearing Right of Way" or the "Blocking Right of Way"
mode.
The warning light system(s) shall be certified by the light system manufacturer(s), to meet all of the
requirements in the current revision of the NFPA 1901 Fire Apparatus Standard as noted in the General
Requirements section of these specifications. The NFPA required "Certificate of Compliance" shall be
provided with the completed apparatus.
ROOF MOUNTED LIGHT BARS
Two (2) Whelen model MININFPA, 28.50", cab roof warning light bars shall be furnished and rigidly
mounted, one (1) at each side on the cab roof facing to each side of the unit. Each light bar shall be
equipped with four (4) strobe lights and red lenses.
The lights specified above shall be provided in addition to the NFPA required Optical Warning Light
Package and shall be switched independently from the light package. Additionally, wiring for the
independently switched lights specified, shall be run through the Load Management System to ensure that
Allen Volunteer Fire Co., Inc. Tanker Specification
56
Antietam Fire Apparatus, Inc.
the electrical system is not overloaded by the additional amperage draw requirements.
TRAFFIC ADVISER WARNING LIGHT
One (1) Whelen LED "Traffic Advisor", Model TAM65 36", rear directional light shall be installed
on the vertical rear surface of the body. The light shall be equipped with six (6) lamps. The directional
light shall be activated by a control module. The control module shall be conveniently located near the
driver's position. The rear directional light shall be wired through the load management system of the unit.
ELECTRIC HORN
A single electric horn activated by the steering wheel horn button shall be furnished.
BACK-UP ALARM
A solid state back-up alarm shall be provided and installed at the rear of the apparatus under the
tailboard. The back-up alarm shall activate automatically when the transmission is placed in reverse gear
and the ignition is "on".
AIR HORNS
Two (2) chrome plated air horns shall be at the front of the vehicle. The air horns shall be mounted
in full compliance with NFPA-1901. A 3/8" minimum air line "teed" with equal distance from each horn
shall be installed.
Both air horns shall be recessed in the front bumper.
The air horn(s) shall be controlled by a push button located on the dash, on the officer's side and
the steering horn button for the driver. An air horn/standard horn selector switch shall be furnished on the
dash for the drivers steering horn button.
FEDERAL Q2B MECHANICAL SIREN
One (1) Federal Model #Q2B mechanical siren shall be provided to provide audible warning.
The Q2B siren shall be wired through the load management system to prevent excessive
amperage draw. The siren shall be provided in addition to the required minimum NFPA audible warning
requirements.
The Q2-B siren shall be semi-recessed into the center of the front bumper. The siren shall be
recessed so the front grille portion of the siren is exposed and protruding beyond the bumper.
A second push button siren brake switch shall be provided on the cab dash near the officers
seating position.
Allen Volunteer Fire Co., Inc. Tanker Specification
57
Antietam Fire Apparatus, Inc.
A Linemaster #632 floor mounted foot switch shall be provided for the driver. A siren brake button
shall be provided near the driver's position.
The siren shall be also be controlled by a push button located on the dash, on the officer's side.
Allen Volunteer Fire Co., Inc. Tanker Specification
58
Antietam Fire Apparatus, Inc.
PUMP



HALE QMAX-150
1500 G.P.M.
Single Stage
The pump must deliver the percentage of rated capacity at the pressure listed below:




100% of rated capacity at 150 P.S.I. net pump pressure
100% of rated capacity at 165 P.S.I. net pump pressure
70% of rated capacity at 200 P.S.I. net pump pressure
50% of rated capacity at 250 P.S.I. net pump pressure
When dry, the pump shall be capable of taking suction and discharge water with a lift of 10 feet in
not more than 30 seconds through 20 feet of appropriate size suction hose.
PUMP ASSEMBLY
The pump shall be of a size and design to mount on the chassis rails of commercial and custom
truck chassis, and have the capacity of 1500 gallons per minute (U.S. GPM), NFPA-1901 rated
performance.
PUMP CONSTRUCTION
The entire pump shall be cast, manufactured and tested at the pump manufacturer's factory.
The pump shall be driven by a drive line from the truck transmission. The engine shall provide
sufficient horsepower and RPM to enable the pump to meet and exceed its rated performance.
The entire pump, both suction and discharge passages, shall be hydrostatically tested to a
pressure of 600 PSI. The pump shall be fully tested at the pump manufacturer's factory to performance
specs as outlined by the latest NFPA-1901. Pump shall be free from objectionable pulsation and vibration.
The pump body and related parts shall be of fine grain alloy cast iron with a minimum tensile
strength of 30,000 PSI. All moving parts in contact with water shall be of high quality bronze or stainless
steel. Pumps utilizing castings made of lower tensile strength cast iron are not acceptable.
Pump body shall be horizontally split, on a single plane in two sections for easy removal of entire
impeller assembly including wear rings and bearings from beneath the pump without disturbing piping or
the mounting of the pump in chassis.
PUMP SHAFT
Pump shaft to be rigidly supported by three bearings for minimum deflection. One high lead bronze
sleeve bearing to be located immediately adjacent to the impeller (on side opposite the gearbox). The
sleeve bearing is to be lubricated by a force fed, automatic oil lubricated design, pressure balanced to
Allen Volunteer Fire Co., Inc. Tanker Specification
59
Antietam Fire Apparatus, Inc.
exclude foreign material.
The pump shaft shall be heat-treated, electric furnace, corrosion resistant stainless steel to be
super-finished under packing with galvanic corrosion (zinc foil separators in packing) protection for longer
shaft life. Pump shaft must be sealed with double-lip oil seal to keep road dirt and water out of gearbox.
PUMP IMPELLER
The pump shall have one double suction impeller. The pump body shall have two opposed
discharge volute cutwaters to eliminate radial unbalance. (No exceptions)
Pump impeller shall be hard, fine grain bronze of the mixed flow design; accurately machined and
individually balanced. The vanes of the impeller intake eyes shall be of sufficient size and design to
provide ample reserve capacity utilizing minimum horsepower.
Impeller clearance rings shall be bronze, easily renewable without replacing impeller or pump
volute body, and of wrap-around double labyrinth design for maximum efficiency. (No exceptions.)
PUMP PACKING GLAND
The pump shaft shall have only one (1) packing gland located on inlet side of the pump. It shall be
a split design for ease of repacking. The packing gland must be a full circle threaded design to exert
uniform pressure on packing and to prevent cocking and uneven packing load when it is tightened. It shall
be easily adjusted by hand with rod or screwdriver with no special tools or wrenches required. The
packing rings shall be of a unique permanently lubricated, long life graphite composition and have
sacrificial zinc foil separators to protect the pump shaft from galvanic corrosion.
PUMP DRIVE UNIT
The drive unit shall be completely assembled and tested at the pump manufacturer's factory.
Pump drive unit shall be of sufficient size to withstand up to 16,000 lbs. ft. of torque of the engine in
both road and pump operating conditions. The drive unit shall be designed of ample capacity for
lubrication reserve and to maintain the proper operating temperature.
The gearbox drive shafts shall be of heat treated chrome nickel steel and at least 2-3/4 inches in
diameter on both the input and output drive shafts. They shall withstand the full torque of the engine in
both road and pump operating conditions.
All gears, both drive and pump, shall be of the highest quality electric furnace chrome nickel steel.
Bores shall be ground to size and teeth integrated, chrome-shaven and hardened, to give an extremely
accurate gear for long life, smooth, quiet running and higher load carrying capability. An accurately cut
spur design shall be provided to eliminate all possible end thrust.
Allen Volunteer Fire Co., Inc. Tanker Specification
60
Antietam Fire Apparatus, Inc.
PUMP RATIO
The pump ratio shall be selected by the apparatus manufacturer to give maximum performance
with the engine and transmission selected.
The manufacturer shall supply at time of delivery copies of the pump manufacturer's certification of
hydrostatic testing, the engine manufacturer's current certified brake horsepower curve.
PUMP SHIFT CONTROL
The drive unit shall be equipped with a power shift. The shifting mechanism shall be a heat
treated, hard anodized aluminum power cylinder with stainless steel shaft. An air operated in-cab control
for rapid shift shall be provided that locks in road or pump, with a neutral position for use when manual
override is required.
PUMP SHIFT INDICATOR LIGHTS
For automatic transmissions, three (3) green warning lights shall be provided to indicate to the
operator(s) when the pump has completed the shift for Road to Pump position. Two (2) green lights to be
located in the truck driving compartment and one (1) green light on pump operator's panel adjacent to the
throttle control. For manual transmissions, one (1) green warning light shall be provided for the driving
compartment. All lights to have appropriate identification/instruction plates.
TRANSMISSION LOCK
The automatic transmission furnished in the chassis shall have a lock-up assembly which brings
the transmission to direct drive and prevents the transmission from shifting gears while in the pumping
mode.
BRAKING SYSTEM
A positive braking system shall be provided to prevent vehicle movement during pumping
operations. The air brakes furnished must satisfy this requirement.
PUMP MOUNTS
Extra heavy duty pump mounting brackets shall be furnished. These shall be bolted to the frame
rails in such a position to perfectly align the pump so that the angular velocity of the drive line joints shall
be the same on each end of the drive shaft. This shall assure full capacity performance with a minimum of
vibration. Mounting hardware shall utilize Grade 8 bolts.
Pumps which are not mounted directly to the frame will not be considered. Under no circumstance
shall the pump function as a frame cross member.
Allen Volunteer Fire Co., Inc. Tanker Specification
61
Antietam Fire Apparatus, Inc.
TOTAL PRESSURE MASTER RELIEF VALVE SYSTEM
The pump shall be equipped with a Hale Model TPM Total Pressure Master relief valve system to
provide automatic protection against excess inlet or discharge pressure variations during pumping
operations. This system shall incorporate an operator's panel mounted pressure control valve with an
easy to read and set pressure adjusting scale. Automatic pressure sensing devices shall be provided to
monitor and control pressure changes on both sides of the pump to comply fully with NFPA-1901
requirements. Excess pressures shall be plumbed to discharge water under the pump enclosure away
from the pump operator.
The Total Pressure Master relief valve control shall eliminate the need for additional external
mounted relief valves.
PUMP CERTIFICATION
The pump shall be third party performance tested to meet the requirements of NFPA-1901. To
ensure top quality and integrity, the test company shall be Underwriter's Laboratories (UL). NO
EXCEPTIONS!
PRIMING PUMP
The priming pump shall be a 12-volt Hale model ESP Oil-Less, positive displacement vane type
primer, electrically driven. One priming control shall open the priming valve and start the priming motor.
The primer shall be capable of priming without the use of primer oil. The primer shall be connected to the
power source with a 300 amp fusible link.
The Hale primer shall be activated by a manual valve located on the pump operator's panel. The
valve shall activate the primer motor, which shall create a vacuum. Valve actuation may be accomplished
while the main pump is operational, if necessary to assure complete prime.
An additional primer control valve shall be furnished, piped directly to the front suction line piping.
The priming valve shall activate the standard pump primer to minimize pump cavitation during remote
suction operations and shall be located on the pump operator's panel.
MASTER DRAIN VALVE
A rotary type, 12 port master drain valve shall be provided and controlled at the lower portion of the
side pump panel. The valve shall be located in pump compartment lower than the main body and
connected in such a manner as to allow complete water drainage of the pump body and all required
accessories. Water shall be drained below the apparatus body and away from the pump operator.
INDIVIDUAL BLEEDERS AND DRAINS
All lines shall drain through the master drain valve or shall be equipped with individual drain
valves, easily accessible and labeled.
Allen Volunteer Fire Co., Inc. Tanker Specification
62
Antietam Fire Apparatus, Inc.
One (1) individual "TRIDENT" quarter turn drain valve shall be furnished for each 1-1/2" or larger
discharge port and each 2-1/2" gated auxiliary suction.
Drain/bleeder valves shall be located at the bottom of the side pump module panels.
All drains and bleeders shall discharge below the running boards.
SYNFLEX SUCTION, DISCHARGE, PRESSURE AND CONTROL LINES
Small lines within the pump enclosure shall be constructed from Synflex hose. Uses include, but
are not limited to such lines as priming control, gauge lines, drain lines, air control valves, pump shift,
supplemental cooling, foam flush and air bleeder valves.
PUMP MODULE
The pump module shall be a self-supported structure mounted independently from the body and
chassis cab. The design must allow normal frame deflection without imposing stress on the pump module
structure or side running boards. The pump module shall be securely mounted to the chassis frame rails.
The pump module shall be a welded frame work utilizing structural steel components properly
braced to withstand the rigors of chassis frame flex.
DUNNAGE AREA
A dunnage area shall be provided above the pump enclosure for equipment mounting and storage.
This area shall be furnished with a removable 3/16" aluminum tread plate floor and side panels.
NOTE: The size of this storage area may vary when top mounted crosslays, booster reel(s), etc., are
specified and located in this area.
SUCTION INLETS
Two (2) 6" N.S.T. suction inlets shall be provided, one on the left pump panel and one on the right
pump panel. A removable strainer shall be installed on each inlet.
PUMP SUCTION ENDS
The main pump suction inlets shall be furnished with a short suction end, terminating with only the
suction threads protruding through the side panel to minimize the distance an exterior appliance protrudes
beyond the pump panel.
One (1) 6" NST chrome plated long handle pressure vented cap shall be installed on each.
Allen Volunteer Fire Co., Inc. Tanker Specification
63
Antietam Fire Apparatus, Inc.
FRONT SUCTION
A 6" N.S.T. front suction inlet shall be provided at the front of the vehicle, plumbed from the pump.
The front inlet shall be located above the right hand side of the front bumper extension and shall
terminate with a chromed brass, chicksan style swivel to allow a minimum of 180 degree rotation of the
inlet for suction hose attachment.
The front suction pipe shall be equipped with a chrome 6" NSTM thread adapter.
The front inlet shall be plumbed utilizing 5", schedule 10 stainless steel piping, 45 degree weld
elbows and a limited number of 90 degree sweep elbows in a welded assembly from the pump to the front
of the cab.
A minimum of two (2) grooved pipe couplings shall be furnished in this assembly to allow for flex
and serviceability.
The front suction plumbing shall be fitted with a Hale Master Intake Valve (MIV), on the front
suction inlet. The valve shall be in the pump enclosure area with a manual override located directly on the
valve actuator. The valve body and all related components that are in contact with water shall be
manufactured of fine grained, corrosion resistant bronze.
The valve housing shall incorporate a pressure relief valve, set at the pump manufacturers facility
to a rating of 125 PSI. The pressure relief valve shall provide protection for the suction hose even with the
valve in the closed position. The valve shall incorporated a NFPA compliance, large diameter hose air
bleed valve, controlled at the operator's panel.
The front suction valve shall be operated by a twelve (12) volt DC motor, controlled form the pump
operator's panel. It shall also incorporate a manual override, mounted at the valve. The electric control
shall incorporate a placard with status lights to indicate whether the valve is in the closed, open or throttled
position. The valve shall not be able to move from fully open to fully closed in under three (3) seconds, in
compliance with NFPA-1901.
One (1) 6" NST chrome plated long handle vented cap(s) shall be installed on front suction.
AUXILIARY SIDE SUCTION(S)
One (1) 2-1/2" auxiliary suction shall be provided at the driver side pump panel, to the rear of the
main inlet. The 2-1/2" auxiliary suction shall terminate with a removable strainer, chrome plated 2-1/2"
NST female swivel with a chrome plated plug and retaining chain.
A 2 1/2" Akron #8800 series full flow, stainless steel ball valve shall be provided for the driver side
rear auxiliary suction.
A 1/4 turn swing control handle shall be provide on the driver side rear auxiliary suction valve
All side gated inlet valves shall be recess mounted behind the side pump panels or body panels.
(No Exceptions)
Allen Volunteer Fire Co., Inc. Tanker Specification
64
Antietam Fire Apparatus, Inc.
TANK TO PUMP
Two (2) 4" full flow tank to pump lines shall be piped through the front bulkhead of the tank with a
90 degree elbow down into two (2) individual sumps at the front of the tank for maximum flow. These lines
shall be plumbed directly into the rear of the pump suction manifold for maximum efficiency.
Two (2) 3" full-flow, in-line ball valves and check valves shall be provided to prevent accidental
pressurization of the water tank through the pump connection. Connection from valve to tank shall be
made using non-collapsible flexible rubber hose.
Each tank to pump connection shall be equipped with a 3" Akron #8800 series full flow, stainless
steel ball valve between the pump suction manifold and the water tank outlets.
The tank to pump valves shall be air operated with a control switch located on the operator's panel
with function plate.
TANK FILL
One (1) 2 1/2" gated full flow pump to tank refill line controlled at the pump panel shall be provided.
A deflector shield inside the tank shall be furnished. Tank fill plumbing shall utilize 2 1/2" high pressure
hose for tank connection to accommodate flexing between components. (NO EXCEPTIONS)
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided between the
pump discharge manifold and the water tank.
A push/pull control handle shall be located on the operator's panel with function plate.
DRIVER'S SIDE MAIN DISCHARGE #1
A discharge shall be provided and located at the driver's side pump panel. The driver's side
discharges #1 shall terminate with NST threads, through the left panel above the main pump intake.
The main pump discharge shall be plumbed directly from the pump discharge manifold utilizing
direct connect discharge valve flanges.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the driver's
side #1 discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The discharge valve shall be equipped with integral 2 1/2" NST, 30 degree, chrome plated elbow.
A 2 1/2" NST chrome plated pressure vented cap shall be installed on driver's side #1 discharge.
The driver's side #1 discharge valve shall be controlled by a 1/4 turn swing control handle located
on the operator's panel.
The driver's side #1 discharge shall be equipped with a 2 ½ “ diameter Noshok pressure gauge.
The gauge shall have a rugged corrosion free stainless steel case and clear scratch resistant molded
crystals with captive O-ring seals to ensure distortion free viewing and seal the gauge. The gauge shall be
Allen Volunteer Fire Co., Inc. Tanker Specification
65
Antietam Fire Apparatus, Inc.
filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent
lens condensation and ensure proper operation from –40°F to +160°F.
The gauge shall exceed ANSI B40.1 Grade A requirements with an accuracy of +/- 1.5% full scale
and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube
base to increase the tube life and gauge accuracy.
A polished chrome-plated stainless steel bezel shall be provided to prevent corrosion and protect
the lens and gauge case. The gauge shall have black graphics on a white background.
DRIVER'S SIDE MAIN DISCHARGE #2
A discharge shall be provided and located at the driver's side pump panel. The driver's side
discharges #2 shall terminate with NST threads, through the left panel above the main pump intake.
The main pump discharge shall be plumbed directly from the pump discharge manifold utilizing
direct connect discharge valve flanges.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the driver's
side #2 discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The discharge valve shall be equipped with integral 2 1/2" NST, 30 degree, chrome plated elbow.
A 2 1/2" NST chrome plated pressure vented cap shall be installed on driver's side #2 discharge.
The driver's side #2 discharge valve shall be controlled by a 1/4 turn swing control handle located
on the operator's panel.
The driver's side #2 discharge shall be equipped with a 2 ½ “ diameter Noshok pressure gauge.
The gauge shall have a rugged corrosion free stainless steel case and clear scratch resistant molded
crystals with captive O-ring seals to ensure distortion free viewing and seal the gauge. The gauge shall be
filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent
lens condensation and ensure proper operation from –40°F to +160°F.
The gauge shall exceed ANSI B40.1 Grade A requirements with an accuracy of +/- 1.5% full scale
and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube
base to increase the tube life and gauge accuracy.
A polished chrome-plated stainless steel bezel shall be provided to prevent corrosion and protect
the lens and gauge case. The gauge shall have black graphics on a white background.
DRIVER'S SIDE MAIN DISCHARGE #3
A discharge shall be provided and located at the driver's side pump panel. The driver's side
discharges #3 shall terminate with NST threads, through the left panel above the main pump intake.
The main pump discharge shall be plumbed directly from the pump discharge manifold utilizing
direct connect discharge valve flanges.
Allen Volunteer Fire Co., Inc. Tanker Specification
66
Antietam Fire Apparatus, Inc.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the driver's
side #3 discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The discharge valve shall be equipped with integral 2 1/2" NST, 30 degree, chrome plated elbow.
A 2 1/2" NST chrome plated pressure vented cap shall be installed on driver's side #3 discharge.
The driver's side #3 discharge valve shall be controlled by a 1/4 turn swing control handle located
on the operator's panel.
The driver's side #3 discharge shall be equipped with a 2 ½ “ diameter Noshok pressure gauge.
The gauge shall have a rugged corrosion free stainless steel case and clear scratch resistant molded
crystals with captive O-ring seals to ensure distortion free viewing and seal the gauge. The gauge shall be
filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent
lens condensation and ensure proper operation from –40°F to +160°F.
The gauge shall exceed ANSI B40.1 Grade A requirements with an accuracy of +/- 1.5% full scale
and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube
base to increase the tube life and gauge accuracy.
A polished chrome-plated stainless steel bezel shall be provided to prevent corrosion and protect
the lens and gauge case. The gauge shall have black graphics on a white background.
OFFICER'S SIDE MAIN DISCHARGE #1
A discharge shall be provided and located at the officer's side pump panel. The officer's side
discharges #1 shall terminate with NST threads, through the officer's side panel above the main pump
intake.
The main pump discharge shall be plumbed directly from the pump discharge manifold utilizing
direct connect discharge valve flanges.
A 4" Akron, #8840 series, full flow, flat ball valve shall be provided for the officer's side #1
discharge.
The discharge valve shall be equipped with a straight 4" NST adapter that shall be equipped with a
4" NST, 30-degree, chrome plated elbow.
The officer's side #1 discharge cap provided as standard equipment shall be deleted.
A 4" NSTF X 5" Storz Kochek S37S straight adapter w/cap shall be provided on the officer's side
#1 discharge.
The officer's side #1 discharge valve shall be gated with an Akron Hand wheel controlled, inline
valve. The valve shall be controlled at the pump operator's panel with a chrome plated hand wheel and
mechanical valve position indicator.
The officer's side #1 discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled
pressure gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1
Allen Volunteer Fire Co., Inc. Tanker Specification
67
Antietam Fire Apparatus, Inc.
Grade A requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
OFFICER'S SIDE MAIN DISCHARGE #2
A discharge shall be provided and located at the officer's side pump panel. The officer's side
discharges #2 shall terminate with NST threads, through the officer's side panel above the main pump
intake.
The main pump discharge shall be plumbed directly from the pump discharge manifold utilizing
direct connect discharge valve flanges.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the officer's
side #2 discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The discharge valve shall be equipped with integral 2 1/2" NST, 30 degree, chrome plated elbow.
A 2 1/2" NST chrome plated pressure vented cap shall be installed on officer's side #2 discharge.
The officer's side #2 discharge valve shall be controlled by a 1/4 turn swing control handle located
on the operator's panel.
The officer's side #2 discharge shall be equipped with a 2 ½ “ diameter Noshok pressure gauge.
The gauge shall have a rugged corrosion free stainless steel case and clear scratch resistant molded
crystals with captive O-ring seals to ensure distortion free viewing and seal the gauge. The gauge shall be
filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent
lens condensation and ensure proper operation from –40°F to +160°F.
The gauge shall exceed ANSI B40.1 Grade A requirements with an accuracy of +/- 1.5% full scale
and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube
base to increase the tube life and gauge accuracy.
A polished chrome-plated stainless steel bezel shall be provided to prevent corrosion and protect
the lens and gauge case. The gauge shall have black graphics on a white background.
DRIVER SIDE REAR DISCHARGE
A 2 1/2" NST rear discharge shall be provided at the rear of the vehicle, plumbed from the pump.
The discharge shall be located at the rear of the body, on the driver side, in a location directed by
engineering, based on the configuration of the body.
The driver side rear discharge pipe shall be equipped with a chrome 2 1/2" NSTM thread adapter.
The driver side rear discharge shall be plumbed utilizing 2 1/2" schedule 10, stainless steel piping,
Allen Volunteer Fire Co., Inc. Tanker Specification
68
Antietam Fire Apparatus, Inc.
45 degree threaded elbows and a limited number of 90 degree sweep elbows in an assembly from the
pump to the rear of the vehicle.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the driver side
rear discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The driver side rear discharge valve shall be controlled by a push/pull handle located on the
operator's panel.
One (1) 2 1/2" NST chrome plated pressure vented cap(s) shall be installed at the driver side rear
discharge.
The driver side rear discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled
pressure gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1
Grade A requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
DECK GUN DISCHARGE
A deck gun discharge shall be plumbed from the pump to an area on top of the vehicle. The deck
gun piping shall be firmly supported and braced.
The deck gun discharge shall be located in the center of the dunnage area above the pump
module. A pedestal type, 1/4" steel plate support assembly shall be provided to stabilize deck gun
plumbing below deck gun mount flange.
The deck gun discharge pipe shall terminate with 3" NPT threads.
To improve the operation range of the deck gun, the discharge pipe shall be outfitted with a TFT
(18") Extend-A-Gun, part # XG18VL-PL. The Extend-A-Gun shall be wired to the hazard light on the cab
dash.
The deck gun piping shall be designed so the overall height of the deck gun in the mounted/stowed
position does not exceed the tallest point on the cab/body.
The deck gun discharge shall be plumbed utilizing 3" schedule 10, stainless steel piping, 45 degree
threaded elbows and a limited number of 90 degree sweep elbows in an assembly from the pump to the
deck gun location.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability.
Allen Volunteer Fire Co., Inc. Tanker Specification
69
Antietam Fire Apparatus, Inc.
A 3" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the deck gun
discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The deck gun discharge valve shall be controlled by a push/pull handle located on the operator's
panel.
The deck gun discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled pressure
gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1 Grade A
requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
AKRON MANUAL DECK GUN
An Akron model #3416 "Apollo" deck gun shall be supplied and mounted on the deck gun
discharge. The monitor shall be equipped with a portable ground base with a 4" Storz inlet. The monitor
shall come equipped with a set of stack tips and an Akron model #5160 "AKROMATIC" 1250 GPM nozzle.
The monitor shall also include the following: Pressure gauge on the monitor, carry handle for portable
usage, grease fittings for maintenance, safety chains, hardened steel ground spikes and Pyrolite
construction.
DECK GUN PAINT
The deck gun, pipe and flange shall be painted job color PPG # Job Color - __________.
FRONT DISCHARGE
A 1 1/2" front #1 discharge shall be plumbed to the front bumper of the vehicle.
The front #1 discharge shall terminate on the top center of the front bumper extension gravel shield
with a chrome 1 1/2" NSTM chicksan swivel adapter.
The front #1 discharge shall be plumbed utilizing 2" schedule 10, stainless steel piping, 45 degree
threaded elbows and a limited number of 90 degree sweep elbows in an assembly from the pump to the
front of the vehicle.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability. Automatic discharge drains shall be provided at all low points in the plumbing.
A 2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the front #1
discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The front #1discharge valve shall be controlled by a push/pull handle located on the operator's
panel.
Allen Volunteer Fire Co., Inc. Tanker Specification
70
Antietam Fire Apparatus, Inc.
A 1 1/2" NST chrome plated pressure vented cap shall be installed the front #1 discharge.
The front #1 discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled pressure
gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1 Grade A
requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
FRONT DISCHARGE
A 2 1/2" front discharge shall be plumbed to the front bumper of the vehicle.
The front discharge #2 shall terminate on the top driver's side of the front bumper extension gravel
shield with a chrome 2 1/2" NST chicksan swivel adapter.
The front discharge shall be plumbed utilizing 2 1/2" schedule 10, stainless steel piping, 45 degree
threaded elbows and a limited number of 90 degree sweep elbows in an assembly from the pump to the
front of the vehicle.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability. Automatic discharge drains shall be provided at all low points in the plumbing.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the front #2
discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The front #2 discharge valve shall be controlled by a push/pull handle located on the operator's
panel.
One (1) 2 1/2" NST chrome plated pressure vented cap(s) shall be installed the front #2 discharge.
The front #2 discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled pressure
gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1 Grade A
requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
HORIZONTAL SPEEDLAY #1
Speedlay #1 shall be a transverse hose bed, which shall be designed as an integral part of the
pump module design, located forward of the pump just above the frame rails. Hose deployment shall be
accomplished from either side of the apparatus. The speedlay hose bed flooring shall be designed to be
removable, constructed from brushed finish, perforated aluminum material.
Allen Volunteer Fire Co., Inc. Tanker Specification
71
Antietam Fire Apparatus, Inc.
The hose shall be capable of being reloaded from either side of the vehicle and from access slots
provided on the front of the pump module when standing in the pump module walkway.
The outer edge of the speedlay #1 hosebed shall be trimmed stainless steel scuff plates.
The speedlay #1 discharge shall terminate through the rear wall of the hosebed with a 1 1/2"
NSTM chicksan swivel adapter. The hosebed rear wall shall be slotted at the top to allow the swivel to
through the wall, allowing the pre-connected hose to be pulled off either side of the apparatus without
kinking the hose at the coupling connection.
Speedlay #1 shall be designed to have a minimum total capacity of 3.5 cubic feet as required by
NFPA -1901 to accommodate a minimum of 200 feet of 1-3/4" fire hose. The hose shall be loaded in a
double stack configuration.
The speedlay #1 discharge shall be plumbed utilizing 2" schedule 10, stainless steel piping and/or
flexible hose, 45 degree threaded elbows and a limited number of 90 degree sweep elbows in an
assembly from the pump to speedlay hosebed.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability.
A 2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the speedlay #1
discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The speedlay #1 discharge valve shall be controlled by a push/pull handle located on the
operator's panel.
The speedlay #1 discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled pressure
gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1 Grade A
requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
HORIZONTAL SPEEDLAY #2
Speedlay #2 shall be a transverse hose bed, which shall be designed as an integral part of the
pump module design, located forward of the pump just above the lower speedlay. Hose deployment shall
be accomplished from either side of the apparatus. The speedlay hose bed flooring shall be designed to
be removable, constructed from brushed finish, perforated aluminum material.
The hose shall be capable of being reloaded from either side of the vehicle and from access slots
provided on the front of the pump module when standing in the pump module walkway.
The outer edge of the speedlay #2 hosebed shall be trimmed stainless steel scuff plates.
The speedlay #2 discharge shall terminate through the rear wall of the hosebed with a 1 1/2"
NSTM chicksan swivel adapter. The hosebed rear wall shall be slotted at the top to allow the swivel to
Allen Volunteer Fire Co., Inc. Tanker Specification
72
Antietam Fire Apparatus, Inc.
through the wall, allowing the pre-connected hose to be pulled off either side of the apparatus without
kinking the hose at the coupling connection.
Speedlay #2 shall be designed to have a minimum total capacity of 3.5 cubic feet as required by
NFPA -1901 to accommodate a minimum of 200 feet of 1-3/4" fire hose. The hose shall be loaded in a
double stack configuration.
The speedlay #2 discharge shall be plumbed utilizing 2" schedule 10, stainless steel piping and/or
flexible hose, 45 degree threaded elbows and a limited number of 90 degree sweep elbows in an
assembly from the pump to speedlay hosebed.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability.
A 2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the speedlay #2
discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The speedlay #2 discharge valve shall be controlled by a push/pull handle located on the
operator's panel.
The speedlay #2 discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled pressure
gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1 Grade A
requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
HORIZONTAL SPEEDLAY #3
Speedlay #3 shall be a transverse hose bed, which shall be designed as an integral part of the
pump module design, located forward of the pump just above the lower speedlay. Hose deployment shall
be accomplished from either side of the apparatus. The speedlay hose bed flooring shall be designed to
be removable, constructed from brushed finish, perforated aluminum material.
The hose shall be capable of being reloaded from either side of the vehicle and from access slots
provided on the front of the pump module when standing in the pump module walkway.
The outer edge of the speedlay #3 hosebed shall be trimmed stainless steel scuff plates.
The speedlay #3 discharge shall terminate through the rear wall of the hosebed with a 2 1/2"
NSTM chicksan swivel adapter. The hosebed rear wall shall be slotted at the top to allow the swivel to
through the wall, allowing the pre-connected hose to be pulled off either side of the apparatus without
kinking the hose at the coupling connection.
Speedlay #3 shall be designed to have a minimum total capacity of 3.5 cubic feet as required by
NFPA -1901 to accommodate a minimum of 200 feet of 2 1/2" fire hose. The hose shall be loaded in a
triple stack configuration.
Allen Volunteer Fire Co., Inc. Tanker Specification
73
Antietam Fire Apparatus, Inc.
The speedlay #3 discharge shall be plumbed utilizing 2 1/2" schedule 10, stainless steel piping
and/or flexible hose, 45 degree threaded elbows and a limited number of 90 degree sweep elbows in an
assembly from the pump to speedlay hosebed.
A minimum of one (1) grooved pipe coupling shall be furnished in this assembly to allow for flex
and serviceability.
A 2 1/2" Akron, #8800 series, full flow, stainless steel ball valve shall be provided for the speedlay
#3 discharge. The valve shall be equipped with the Akron "Tork-Lok" feature.
The speedlay #3 discharge valve shall be controlled by a push/pull handle located on the
operator's panel.
The speedlay #3 discharge shall be equipped with a No-Shok 2 ½” diameter silicone filled pressure
gauge with pulse and vibration dampening. The gauge accuracy shall comply with ANSI B40.1 Grade A
requirements, temperature range shall be from -40° F to +160° F.
Gauges construction shall be a heavy duty caste brass case. Crystal shall be a molded plexiglass
with captive O-ring and secured with a rolled 304 highly polished stainless steel bezel. Gauges shall have
white faces with black lettering and shall include an orange tip pointer for easy readability.
SPEED LAY HOSEBED HOSE RETENTION
Vinyl coated polyester covers shall be provided on each side of the speed lays to retain hose in the
speed lays. The covers shall be secured with expandable loops sewn into the covers and hooks on the
apparatus.
The speed lay end flap shall be yellow in color.
FOAM PIPING
All foam concentrate plumbing from the tank or auxiliary foam inlet to the foam system components
shall be stainless steel.
The foam system piping shall incorporate a check valve to prevent water from entering the foam
tank; the discharge piping shall also include a check valve to prevent foam solution from back feeding into
the discharge side of the pump. Individual discharge piping shall be as specified for each discharge.
The complete foam system shall be tested in accordance with Chapter 17 of NFPA-1901.
HALE FOAMLOGIX 5.0
The apparatus shall be equipped with an automatic electronically controlled, direct injection, rotary
gear pump, and discharge side foam proportioning system. Foam proportioning operation shall be based
on direct measurement of water flow, and remain consistent within the specified flows and pressures.
Allen Volunteer Fire Co., Inc. Tanker Specification
74
Antietam Fire Apparatus, Inc.
SYSTEM REQUIREMENTS
The complete foam proportioning system shall include the following:











Foam Pump
Control System
Tank Selector and Flushing Valves
Foam Concentrate Strainer
Integral Check Valve/ Injector Fitting.
Flowmeter
Control Cables
SAE J1939 CAN Capable Connection
Low Tank Level Switch(es)
Water Discharge Check Valves
Documentation
FOAM PUMP
The foam proportioning system shall be compatible with most Class A foam concentrates. The
foam proportioning system shall be capable of delivering the rated foam concentrate flow with the above
mentioned foam concentrate type. The foam system manufacturer shall provide a list of foam chemicals
that have been tested for compatibility with the foam pump.
The foam proportioning system shall be based on an electric motor driven, rotary gear foam
concentrate pump, rated at 5.0 GPM (19 LPM) foam concentrate flow rate with maximum operating
pressure of 250 PSIG (17 BAR). The electric motor shall be powered by 12 volts direct current with a ¾
Hp (0.5 Kw) power rating at a maximum current draw of 60 AMPS.
The rotary gear pump shall be close coupled to the motor without an oil filled gearbox. The foam
concentrate pump and all wetted parts of the system shall be constructed of corrosion resistant materials
compatible with all foam concentrates being used. The pump body, pump head and pump cover shall be
constructed of bronze with pump shaft, gears and bearings constructed of stainless steel. A mechanical
pump shaft seal shall be provided to prevent foam concentrate leakage around the rotating shaft. An
internal foam concentrate relief valve constructed of stainless steel and preset at the factory for maximum
system operating pressure shall be incorporated into the foam pump to protect the pump from overpressurization. NO components of the foam concentrate pump and wetted parts of the foam system shall
be manufactured of aluminum.
The foam pump/motor assembly shall be permanently attached to an apparatus mountable base
plate. A foam concentrate flowmeter shall be integral to the foam concentrate pump. The foam
concentrate flowmeter shall provide a signal to the electronic control unit to make sure the proper amount
of foam concentrate is injected into the discharge stream.
The entire base plate mounted assembly shall have electrical components sealed to NEMA 4X or
equiv. for mounting in the apparatus pump compartment or any suitable location on the apparatus. The
pump shall be mounted to allow gravity feed of foam concentrate from the foam tank to the pump.
Allen Volunteer Fire Co., Inc. Tanker Specification
75
Antietam Fire Apparatus, Inc.
CONTROL SYSTEM
The system shall be equipped with an electronic control unit, suitable for installation on the pump
operator panel as the single point of operation for the foam proportioning system. Incorporated within the
control unit shall be a microprocessor that receives input from water flowmeter(s) while receiving foam
concentrate pump output information from the foam concentrate flowmeter. The microprocessor, through
constant comparison of the flow signals, shall ensure the operator preset proportional amount of foam
concentrate is injected into the discharge stream of the fire pump. Control unit shall utilize a single sealed
electrical connector on the rear panel. Wiring harness shall provide an SAE J1939 CAN connection for
diagnostics and systems operations/communications. Control unit shall have an environmentally sealed
membrane front panel and sealed metallic housing.
The electronic control unit shall permit the pump operator to perform the following control and
operation functions for the foam proportioning system:

















Provide push-button ON/OFF control of foam proportioning system.
Provide push-button control of foam proportioning rates from 0.1% to 10.0%, in 0.1% increments.
Show real time flow rate of water or foam solution.
Show total volume of water or foam solution discharged during and after foam operations.
Show foam concentrate injection rate.
Show total amount of foam concentrate consumed.
Permit resetting of totalized values for water and foam concentrate.
Simulate water flow rates for manual operation, calibration and testing of foam system.
Enable system setup and full range system diagnostic functions.
Indicate on LED bar graph foam concentrate is being injected and the foam system capacity.
Indicate on LED bar graph when system capacity is not within design parameters.
Store independent default values for Class A and Class B foam concentrate injection.
Flash a “low concentrate” warning when the foam concentrate tank runs low.
Flash a “no concentrate” warning and shut the system off when the foam tank is empty.
Flash a “low battery” warning when battery voltage is low enough to affect system operation.
Flash a “hot” warning when system is running hot due to low voltage or radiant heat.
Read out calibration valves to allow setting up a replacement unit.
A power distribution box shall be attached to the base plate to provide ease of installation. The
distribution box shall be sealed to a NEMA 4X or equiv. rating to permit installation in the pump
compartment.
Foam concentrate flow feedback shall be provided to the control unit through the distribution box
by a sensor mounted in the foam pump body. Rotors in the foam discharge side of the foam pump shall
provide the targets to pulse the sensor to generate a feedback signal.
The distribution box shall receive 12 volt direct current power from the apparatus electrical system
as the only source of power to operate the system and power component sensors. Control power shall be
distributed to the control unit, flowmeter sensor and foam concentrate feedback sensor through a
conductor in the cable sets provided by the foam proportioner manufacturer. The microprocessor in the
control unit shall process input signals from the flowmeter sensor and foam feedback sensor to determine
the proper duty cycle for the electric motor to run. The distribution box shall provide power to the electric
motor, based on signals received from the control unit, at a variable rate to ensure that the correct
proportion of foam concentrate, preset by the pump operator on the control unit, is injected into the water
Allen Volunteer Fire Co., Inc. Tanker Specification
76
Antietam Fire Apparatus, Inc.
pump discharge stream. The distribution box shall have a main power control switch and over current
protection for the foam proportioning system.
All primary electrical wires for the foam concentrate system shall be type SXL or GXL (SAE
J1128) per NFPA requirements. Electrical connections shall be made using heavy duty 5/ 16 inch (min)
diameter studs and nuts.
SINGLE FOAM TANK FLUSH
When dual foam concentrate tanks ARE NOT installed flushing capabilities can be provided with a
three-way flush valve. A switch provided integral to the three-way valve shall indicate when the valve is in
the “FLUSH” position. The “FLUSH” position shall provide fresh water-flushing capabilities to prevent foam
concentrate deterioration of the foam pump. When FLUSH is selected the foam pump shall only run for 10
seconds. NFPA required flushing water check valves shall be provided with the single tank flush selector
valve.
FOAM CONCENTRATE STRAINERS
Field serviceable foam concentrate strainers shall be provided in the foam concentrate suction line.
When the strainer shall not be subject to flushing water pressure a plastic bodied in-line strainer shall be
used. The strainer body shall be constructed of plastic with a stainless steel mesh screen and shall be
compatible with both Class A and Class B foam concentrates. A shutoff valve shall be provided to enable
isolation of the strainer for service. The strainer shall be mounted in the pump compartment. The strainer
shall be a low pressure device and shall not be subject to flush water pressure.
Where strainers are subject to flush water pressure, panel mounted field serviceable foam
concentrate strainers rated at 500 PSIG ( 34 BAR) minimum shall be installed on the pump panel. The
strainer body shall be constructed of brass with a chrome cap and an easily removable stainless steel
mesh screen for field servicing. A 1- ½ inch strainer with ¾ inch NPT connection ports shall be used for
Class A foam concentrate and a 2-½ inch strainer with 1 inch NPT connection ports shall be used for
Class B foam concentrate.
INTEGRAL CHECK VALVE/ INJECTOR FITTING and WATERWAY CHECK VALVES
To prevent contamination of the foam concentrate supply, foam concentrate shall be injected into
the water pump discharge stream through an integral check valve/ injector fitting. The check valve/ injector
fitting shall be of one piece body construction of brass, with stainless steel wetted parts.
To prevent contamination of the water pump and apparatus booster tank spring loaded doubledoor type check valves shall be installed in the water pump discharge piping prior to the foam injection
point.
FLOWMETER
A paddlewheel type flowmeter with a stainless steel impeller wheel shall monitor water flow in foam
capable discharges. The flowmeter shall have a 500 PSIG (34 BAR) pressure rating per NFPA
Allen Volunteer Fire Co., Inc. Tanker Specification
77
Antietam Fire Apparatus, Inc.
requirements.
One flowmeter is required for proper operation of the foam proportioning system. Power for the
flowmeter sensor shall be provided through the cable set from the control unit. Flowmeter's shall have
saddle clamp mounting shall be used to mount in stainless steel, brass or iron OEM manifold assembles.
The flowmeter selected shall be sized to adequately monitor the minimum and maximum flow
expected in the foam capable discharges.
CONTROL CABLES
The cables for connection of the control unit, distribution box, flowmeter sensor, flowmeter display
units, pressure transducers and feedback sensor shall have the ability to connect together and total length
shall not exceed 40 feet (12 meters). The connections shall be keyed to prevent misconnection and
improper system operation. Where required a shield drain wire shall be tied to one of the pins on each end
of the cable. No externally attached ferrite beads shall be installed for the purpose of electrical shielding.
When properly connected the connections shall be sealed to NEMA 4X or equivalent.
LOW TANK LEVEL SWITCH
A low tank level switch shall be installed in each foam concentrate tank that supplies foam
concentrate to the foam proportioning system. The low tank level sensor shall be connected to the foam
proportioning system to provide protection against dry running of the foam pump. The low tank level
sensor can be mounted on the side, bottom or top of the foam concentrate tank. The low tank level sensor
and electrical connections shall be sealed to prevent infusion of foam concentrate into the wiring and
possible short circuit of the tank level sensor. The low tank sensor shall be mounted so that the flow of
foam concentrate from the tank does not cause a false low tank reading.
DOCUMENTATION
The foam proportioning system when delivered to the end user shall include: a foam concentrate
compatibility list and (2) two Description, Installation and Operation Manuals. The foam proportioning
system shall have a one-year limited manufacturer warranty.
Accurate concentration proportioning can be achieved, based on the following water flows:







83 GPM water
167 GPM water
500 GPM water
1000 GPM water
1667 GPM water
2500 GPM water
5000 GPM water
6.0% concentration
3.0% concentration
1.0% concentration
0.5% concentration
0.3% concentration
0.2% concentration
0.1% concentration
Note: Multiple discharges plumbed to this system may affect performance if the flow rates are
exceeded by any one discharge or the totality of multiple discharges at one time!
Allen Volunteer Fire Co., Inc. Tanker Specification
78
Antietam Fire Apparatus, Inc.
The discharge piping shall be equipped with a properly sized flowmeter sensor and check valve,
based on the systems capabilities.
The foam system shall be plumbed to the following discharge/s through the discharge piping or
manifold system:
Crosslay #1 discharge
Speedlay #1 discharge
Speedlay #2 discharge
Speedlay #3 discharge
Front discharge
Driver's side rear discharge
Driver's side discharge #1
Officer's side discharge #2
MANUAL DUAL TANK SELECTOR
An operator panel mounted manual dual tank valve to provide manual selection of dual foam
concentrate tanks from the operator panel shall be provided. The manual dual tank selector shall be
electrically interlocked with the low tank switches and control unit. When the selector is switched from one
tank to the other the default foam concentrate injection rate shall automatically change without operator
intervention. Also, when the selector is switched from one tank to the other the low level sensor in the
selected tank shall be active and the other one shall be isolated from the system.
The manual dual tank selector handle shall have a “FLUSH” position between the tank settings.
The “FLUSH” position shall provide a clean water flush of the foam concentrate pump preventing foam
concentrates from mixing and possibly jelling. Switches provided on the manual dual tank valve shall
determine which low tank level sensor is providing feedback and which foam concentrate injection rate to
use. When FLUSH is selected the foam pump shall only run for 10 seconds. All NFPA required flushing
water check valves shall be provided with the manual dual tank selector.
The selection of this item includes one (1) low level tank sensor, and one (1) in-line strainer for the
additional tank requirement.
Allen Volunteer Fire Co., Inc. Tanker Specification
79
Antietam Fire Apparatus, Inc.
PUMP PANEL - SIDE MOUNT
The pump operator's control panel shall be located on the driver side of the apparatus. The pump
enclosure side panels shall be completely removable and designed for easy access and servicing.
PUMP PANEL MATERIAL
The left side operator's panel, gauge panel, right side pump panel and right side access door shall
be fabricated from 1/8" aluminum, coated with black Speedliner material. The Speedliner material shall
provide a non-glare, rubberized textured finish.
HINGED GAUGE PANEL
A full width, vertically hinged gauge access panel shall be provided at the operator's position.
Chrome plated positive locks shall be provided along with chain holders to prevent the front of the gauge
panel from coming in contact with other panels when open.
HINGED PUMP ACCESS DOOR
A 18" high by a minimum of 30" wide pump enclosure access door shall be provided above the
officer's side pump panel. This door shall have a "D" ring, two-point latch mechanism and two (2) gas
shock stay arms for ease of access.
PANEL FASTENERS
Stainless steel machine screws and lock washers shall be used to hold these panels in position.
The panels shall be easily removable to provide complete access to the pump for major service.
CAPS AND ADAPTERS SAFETY TETHER
All applicable discharge and suction caps, plugs and adapters shall be equipped with chrome
plated ball chain or double looped coil chain and secured to the vehicle.
PUMP PANEL TRIM PLATES
A high polish stainless steel trim plate shall be provided around each discharge port and suction
inlet opening to allow accessibility to the respective valve for service and repairs.
DISCHARGE GAUGE TRIM BEZELS
Each individual discharge gauge shall be installed into a decorative chrome-plated mounting bezel
that incorporates valve-identifying verbiage and color labels.
Allen Volunteer Fire Co., Inc. Tanker Specification
80
Antietam Fire Apparatus, Inc.
COLOR CODED IDENTIFICATION TAGS
Color coded identification tags shall be provided for all gauges, controls, connections, switches,
inlets and outlets.
PUMP OPERATOR'S PANEL LIGHT SHIELD
The pump operators panel shall be equipped with a light shield that shall be full width of the control
panel, and shall be positioned to cover the lights and prevent glare.
The light shield shall be equipped with the following lights:
Amdor Luma Bar H2O super bright led strip lights
OFFICER SIDE PANEL LIGHT SHIELD
The officer side pump panel shall be equipped with a light shield that shall be full width of the
control panel, and shall be positioned to cover the lights and prevent glare.
The light shield shall be equipped with the following lights:
Amdor Luma Bar H2O super bright led strip lights
The lights shall be switched with the operator panel lights.
PUMP OPERATOR'S PANEL
Particular attention is to be given to functional arrangement of all controls. The pump operator's
panel shall accommodate the following:
















Hinged gauge panel
Water tank fill valve
Auxiliary suction valve control
All discharge valve controls
Auxiliary engine cooler controls
Water tank suction control valve
Pump primer valve
Engine throttle control
Master compound vacuum gauge
Master pressure gauge
Individual discharge gauges
Pump shift engaged indicator light
Water tank water level indicator
Engine tachometer
Engine oil pressure gauge with audible alarm
Engine water temperature gauge with audible alarm
Allen Volunteer Fire Co., Inc. Tanker Specification
81
Antietam Fire Apparatus, Inc.













Low voltage light and audible alarm
Pump panel light switch
Speed counter (Underwriters)
Pump performance plate (Underwriters)
Pump serial No. plate
Master pump drain valve
Individual drains
Voltmeter
Air inlet/outlet at lower left hand panel
Relief valve with indicator light
Relief valve drains
Pump panel air horn actuation button
Fire research "ThrottleXcel" throttle control
PUMP TEST PORTS
The pump panel shall be equipped with Vacuum & Pressure test plugs to allow for test equipment
to monitor pump pressure and vacuum levels. Chrome plugs and labels shall be provided for the test
ports.
MASTER GAUGES
One (1) 4-1/2" diameter pressure gauge (labeled: "PRESSURE") and one (1) 4-1/2" diameter
compound vacuum gauge (labeled: "INTAKE") shall be provided. The master gauges shall be Class One
Sub-Z II, silicone filled. The gauge faces shall be white with black numerals.
PRESSURE & COMPOUND GAUGE RANGES
All applicable pressure gauges shall have a range of 0 - 400 P.S.I., and the compound gauge shall
have a range of -30" - 0 - 400 P.S.I.
FIRE RESEARCH "THROTTLE XCEL" THROTTLE CONTROL AND MONITORING DISPLAY
The apparatus shall be equipped with a Fire Research ThrottleXcel engine throttle and monitoring
display shall be installed. The case shall be waterproof and have dimensions not to exceed 6 3/4" high by
4 5/8" wide by 1 3/4" deep. The engine throttle control knob shall be 2" in diameter with a serrated grip,
have a red idle push button in the center, and no mechanical stops. Inputs for engine information shall be
from a J1939 databus, other inputs shall be 12 volts DC or from independent sensors.
The engine RPM shall be set to idle when the pump engaged interlock signal is recognized
regardless of the throttle control knob position. Optical technology shall be used to detect the direction and
speed that the control knob rotated for RPM control.
Allen Volunteer Fire Co., Inc. Tanker Specification
82
Antietam Fire Apparatus, Inc.
The following continuous displays shall be provided:







Engine RPM; shown with four daylight bright LED digits more than 1/2" high, updated in
10 RPM increments
Engine oil pressure; shown on an LED bar graph display in 10 psi increments
Engine coolant temperature; shown on an LED bar graph display in 10 degree increments
Battery voltage; shown on an LED bar graph display in 0.5 volt increments
Time and date; shown on a dot matrix message display
Interlock; OK TO PUMP LED is green to indicate throttle ready.
A dot-matrix message display shall show diagnostic and warning messages as they occur. It shall
show monitored apparatus information, stored data, and program options when selected by the
operator. Operator selections and inputs shall be via push buttons on the front panel.
The program shall store the accumulated operating hours for the pump and engine, previous
incident hours, and current incident hours in a non-volatile memory. Stored elapsed hours shall be
displayed at the push of a button. The program shall have calibration and self-diagnostic capabilities. It
shall monitor inputs and support audible and visual warning alarms for the following conditions:







Low Oil Pressure
High Engine Coolant Temperature
High Transmission Temperature
Low Battery Voltage (Engine Off)
Low Battery Voltage (Engine Running)
High Battery Voltage
High Engine RPM
The engine throttle and monitoring display shall be programmed at installation for a specific
engine.
ENGINE COOLER
An auxiliary cooler or heat exchanger shall be installed in the engine compartment between the
engine and the chassis radiator. The cooler shall permit the use of water from the pump for cooling
system. The cooling shall be done without mixing engine and pump water.
TANK LEVEL GAUGE
A Fire Research, model #WLA200-A00, "TANKVISION" gauge that shows the actual volume of
water in the tank shall be provided on the pump operator's panel. The "TANKVISION" gauge is designed
for both ease of operation and installation. The "TANKVISION" gauge utilizes ultra bright LEDs for sunlight
readability and also uses 2 sophisticatedly designed wide-viewing lens for 180° of clear viewing. The
"TANKVISION" gauge utilizes a pressure sender to measure the liquid volume. The gauge shall be
equipped self-calibration feature allows the LED's TANKVISION gauge to be used on tanks of different
shapes and sizes.
Allen Volunteer Fire Co., Inc. Tanker Specification
83
Antietam Fire Apparatus, Inc.
Features:







Flashes warning when the volume is less than 25%. Rapid down scrolling LED's alert the operator
when the tank is almost empty. Remote audio warning available
One size fits all’. The self-calibration feature allows for easy calibration of any shape or size tank
Multiple displays are possible with a single sender through the FRC data bus
Rugged waterproof cast aluminum housing
No fitting needed for poly tank.
Special fittings available for other tank materials.
Connector disconnects at back of display
REMOTE TANK LEVEL GAUGE
An additional Fire Research, model #WLA200-B00, "TANKVISION" gauge that shows the actual
volume of water in the tank shall be provided on the rear of the vehicle. The "TANKVISION" gauge is
designed for both ease of operation and installation. The "TANKVISION" gauge utilizes ultra bright LED's
for sunlight readability and also uses 2 sophisticatedly designed wide-viewing lens for 180° of clear
viewing. The "TANKVISION" gauge utilizes a pressure sender to measure the liquid volume. The gauge
shall be equipped self-calibration feature allows the TANKVISION gauge to be used on tanks of different
shapes and sizes.
Features:








Flashes warning when the volume is less than 25%. Rapid down scrolling LED's alert the operator
when the tank is almost empty. Remote audio warning available.
One size fits all.
The self-calibration feature allows for easy calibration of any shape or size tank.
Multiple displays are possible with a single sender through the FRC data bus.
Rugged waterproof cast aluminum housing.
No fitting needed for poly tank.
Special fittings available for other tank materials.
Connector disconnects at back of display.
The gauge shall use a pressure transducer installed near the bottom of the water tank to determine
the correct volume in the tank.
FOAM TANK LEVEL GAUGE - FOAM TANK "A"
A Fire Research, Model #WLA260-A00, "TANKVISION" gauge that shows the actual volume of
foam in the tank shall be provided on the pump operator's panel. The "TANKVISION" gauge is designed
for both ease of operation and installation. The "TANKVISION" gauge utilizes ultra bright LED's for
sunlight readability and also uses 2 sophisticatedly designed wide-viewing lens for 180° of clear viewing.
The "TANKVISION" gauge utilizes a pressure sender to measure the liquid volume. The gauge shall be
equipped self-calibration feature allows the TANKVISION gauge to be used on tanks of different shapes
and sizes.
Allen Volunteer Fire Co., Inc. Tanker Specification
84
Antietam Fire Apparatus, Inc.
The gauge shall use a pressure transducer installed near the bottom of the foam tank to determine
the correct volume in the tank.
FOAM TANK LEVEL GAUGE - FOAM TANK "B"
A Fire Research, Model #WLA270-A00, "TANKVISION" gauge that shows the actual volume of
foam in the tank shall be provided on the pump operator's panel. The "TANKVISION" gauge is designed
for both ease of operation and installation. The "TANKVISION" gauge utilizes ultra bright LED's for
sunlight readability and also uses 2 sophisticatedly designed wide-viewing lens for 180° of clear viewing.
The "TANKVISION" gauge utilizes a pressure sender to measure the liquid volume. The gauge shall be
equipped self-calibration feature allows the TANKVISION gauge to be used on tanks of different shapes
and sizes.
The gauge shall use a pressure transducer installed near the bottom of the foam tank to determine
the correct volume in the tank.
Allen Volunteer Fire Co., Inc. Tanker Specification
85
Antietam Fire Apparatus, Inc.
WATER TANK
The water tank shall have a capacity of 2500 gallons, constructed from polypropylene material.
FOAM TANK "A"
Included in the total capacity of the water tank, a 50 gallon integral foam storage area shall be built
into the water tank. The foam tank shall have a latched fill tower, properly labeled as the foam fill point. A
valved drain shall be provided.
FOAM TANK "B"
Included in the total capacity of the water tank, a 50 gallon integral foam storage area shall be built
into the water tank. The foam tank shall have a latched fill tower, properly labeled as the foam fill point. A
valved drain shall be provided.
The Poly water tank shall be constructed from 1/2" thick polypropylene sheet stock. This material
shall be a non corrosive stress relieved thermo-plastic, natural in color, and U.V. stabilized for maximum
protection.
The water and foam tanks shall be of a specific configuration and is also designed to be completely
independent of the body and compartments. All joints and seams shall be nitrogen welded and tested for
maximum strength and integrity. The top of the booster tank is fitted with removable lifting eyes designed
with a 3 to 1 safety factor to facilitate easy removability. The transverse swash partitions shall be
manufactured of 3/8" polypropylene (natural in color) and extend from approximately 4" off the floor to just
under the cover. The longitudinal swash partitions shall be constructed of 3/8" polypropylene (natural in
color) and extend from the floor of the tank through the cover to allow for positive welding and maximum
integrity. All partitions shall be equipped with vent and air hoses to permit movement of air and water
between compartments. The partitions shall be designed to provide maximum water flow. All swash
partitions interlock with one another and are welded to each other as well as to the walls of the tank.
TANK LID
The tank cover shall be constructed of 1/2" thick polypropylene, natural in color, and U.V.
stabilized, to incorporate a multi three-piece design, which allows for individual removal and inspection if
necessary. The tank cover shall be recessed 3/8" from the top of the tank and shall be welded to both
sides and longitudinal partitions for maximum integrity. Each one of the covers shall have hold downs
consisting of 2" polypropylene dowels spaced a maximum of 30" apart. These dowels shall extend
through the covers and become welded to the transverse partitions. This shall assist in keeping the cover
rigid under fast filling conditions. A minimum of two lifting dowels shall be drilled and tapped 1/2" X 13" to
accommodate the lifting eyes.
TANK FILL TOWER
The tank shall have a combination vent and manual fill tower. The fill tower shall be constructed of
1/2" polypropylene and shall be 12" W x 36" L outer perimeter. The tower shall be located a minimum of
Allen Volunteer Fire Co., Inc. Tanker Specification
86
Antietam Fire Apparatus, Inc.
6" off the front wall and 10" off either of the side walls. The tower shall have a 1/4" thick removable
polypropylene screen and a polypropylene hinged type cover. The fill tower cover shall be marked as a
water tank fill point.
OVERFLOW AND VENT PIPE
The fill tower shall be fitted with an integral 6" I.D. schedule 40 P.V.C. combination overflow/vent
pipe running from the fill tower through the tank to a 6" coupling flush mounted into the bottom of the tank
to allow water to overflow behind the chassis rear axle.
TANK SUMP
The tank sump shall be a minimum of 10" wide x 10" long x 3" deep. An anti-swirl plate shall be
mounted inside the sump, approximately 1" above the bottom of the sump.
TANK SUMP CONNECTION
The front bulkhead of the water tank shall be fitted with two (2)
A 3" drain plug shall be provided.
OUTLETS
There shall be two (2) standard tank outlets; one for tank-to-pump suction line which shall be a
minimum of 4" coupling and one for a tank fill line which shall be a minimum of a 2" N.P.T. coupling. All
tank fill couplings shall be backed with flow deflectors to break up the stream of water entering the tank.
TANK MOUNTING
The tank shall rest on the body cross members spaced a maximum of 22" apart, and shall be
insulated from these cross members with a minimum of 3/8" nylon webbing or 1/2" rubber, 2-1/2" wide.
The tank shall sit cradle-mounted using four (4) corner angles of 6 x 6 x 4 x 0.250 welded directly to the
body cross members. The angles shall keep the tank from shifting left to right or front to rear. The tank is
designed on the free-floating suspension principle and shall not require the use of hold downs. The tank
shall be completely removable without disturbing or dismantling the apparatus body structure. The hose
bed cross braces shall act as water tank retainers.
10" NEWTON STAINLESS STEEL DUMP - REAR
The rear of the water tank shall be equipped with a 10" Newton Stainless Steel Dump Valve, Model
#1060-34 with a left side mounted manual actuation lever. The dump valve setup shall be capable of
discharging the water tank contents at a rate of at least 1800 G.P.M.
Allen Volunteer Fire Co., Inc. Tanker Specification
87
Antietam Fire Apparatus, Inc.
DIRECT TANK FILL - DRIVER SIDE
One (1) 2-1/2" NST direct tank fill shall be provided at the rear of the body, on the driver side, as
low as possible. The direct tank fill shall be gated with a 2-1/2" Fireman's Friend (TTMA 6-bolt attachment
pattern) check-type fill valve. The fill valve shall be capable of flowing at a rate in excess of 1,000 gallons
per minute and will be of a self deflecting design, requiring no additional diffusion device. The fill valve
shall be constructed of stainless steel, with a spring actuated piston-type sealing mechanism to minimize
seal wear and provide positive sealing of the valve. The fill shall be equipped with a 30 degree elbow
terminating with a 2-1/2" NST female swivel connection.
Allen Volunteer Fire Co., Inc. Tanker Specification
88
Antietam Fire Apparatus, Inc.
APPARATUS BODY DESIGN CONSTRUCTION
The body side and compartment assemblies shall be designed and assembled to provide
maximum strength and durability under all operating conditions.
Special attention shall be taken to minimize corrosion on all fabricated parts and structural
members of the body. All bolt on components shall be provided with a dissimilar metals isolation barrier to
prevent electric corrosion. The body design shall also incorporate removable panels to access spring
hangers, rear body mounts and fuel tank sending units.
The body assembly shall be an all-welded configuration. The body shall be completely isolated
from the cab and pump module structure.
BODY AND COMPARTMENT FABRICATION - STAINLESS STEEL
All compartment panels and body side sheets shall be entirely12 gauge stainless steel (Type
304L). Each side compartment assembly shall be both spot welded and stitch welded to ensure proper
weld penetration on all panels while avoiding the possible warping caused by a full seam weld. The side
compartments shall be welded on a fixture to ensure true body dimensions and squareness of all door
openings. The side compartments and body side panels are then set into a body squaring fixture where
the super structure is installed and the entire body is aligned to be completely symmetrical. The super
structure is then welded to the compartment side panels and reinforcement plates are inserted which
allows the compartment panels to become an integral component of the body support structure. A full
seam weld shall not be used to the applied heat which shall distort sheet metal and remove the protective
coating from the perimeter of the welded area. All seams shall be caulked prior to finish paint to ensure
proper compartment seal.
100" WIDE FIRE BODY
The fire body shall be 100" wide to provide the maximum amount of usable hose bed space,
approximately 76" wide, and to extend the body fenderettes outward for better tire tread coverage. All
lower compartments shall be 26" deep overall, all upper compartments shall be 12" deep overall.
SUPER STRUCTURE - STAINLESS STEEL
The body super structure shall be an all welded configuration utilizing a combination of 3” x 1-1/2”
Type 304 structural grade tubing and Type 304 structural channel.
The super structure shall be designed to totally support the full length and width of the body. The
structure shall be welded to the body side compartments to incorporate the compartments into an integral
part of the body weldment.
The super structure shall be bolted to the sides of the chassis frame at four (4) points.
Allen Volunteer Fire Co., Inc. Tanker Specification
89
Antietam Fire Apparatus, Inc.
STEPPING, STANDING, & WALKING SURFACES
All stepping, standing, and walking surfaces on the body shall meet NFPA #1901 anti-slip
standards. Aluminum tread plate utilized for stepping, standing, and walking surfaces shall be Alcoa No
Slip type. This material shall be certified to meet the NFPA #1901 standard. Upon request by the
Purchaser, manufacturer shall supply proof of compliance with this requirement. (There shall be No
Exceptions allowed for this paragraph)
DRIVER’S SIDE COMPARTMENTATION
One (1) full height/split depth compartment, with a rollup door, forward of the rear wheels.
Compartment dimensions 72” High x 49” Wide, with a door opening of 68” High x 46” Wide.
One (1) full height/split depth compartment, with a rollup door, behind the rear wheels.
Compartment dimensions 72” High x 55” Wide, with a door opening of 68” High x 52” Wide.
One (1) high side compartment, with a rollup door, over the rear wheels. Compartment dimensions
36” High x 109” Wide, with two (2) door openings each 32” High x 50” Wide.
OFFICERS SIDE COMPARTMENTATION
One (1) full height/split depth compartment, with a rollup door, forward of the rear wheels.
Compartment dimensions 72” High x 49” Wide, with a door opening of 68” High x 46” Wide.
One (1) full height/split depth compartment, with a rollup door, behind the rear wheels.
Compartment dimensions 72” High x 55” Wide, with a door opening of 68” High x 52” Wide.
One (1) high side compartment, with a rollup door, over the rear wheels. Compartment dimensions
36” High x 109” Wide, with two (2) door openings each 32” High x 50” Wide.
BODY ROOF COMPARTMENTS (DRIVER'S SIDE)
Roof hatch style compartments shall be provided the full length of the body, on the driver's side of
the body hose bed area and shall be designed as an integral extension of the lower side compartments
with a painted exterior finish. Drain tubes shall be provided at each end of each side compartment which
shall extend down through the lower compartments.
Each side roof compartment shall extend the length of the body, which shall be evenly divided into
three (3) individually accessed areas, which shall be open through from the front to the rear. The
compartment depth shall extend from the ceiling area of the upper side compartments to the top of the
body. The interior compartment width of each side roof compartment shall be a minimum of 13-1/2" inside
width with a 10" wide access door at the top.
Each roof compartment shall be equipped with an overlapping, hinged lift up tread plate door.
These doors shall be constructed of 3/16" aluminum tread plate with a 15 degree break on all sides. Each
door shall have two (2) gas shock style stay open devices which shall also retain the door in the closed
position. Each compartment door shall be equipped with a compartment light, a door button switch and a
Allen Volunteer Fire Co., Inc. Tanker Specification
90
Antietam Fire Apparatus, Inc.
floor drain with a plastic tube to direct the water below the body.
Protective panels shall be applied inside the compartments to cover any exposed wiring or
recessed side body lighting, provided on the unit. These panels shall reduce the overall usable
compartment area in the compartments.
BODY ROOF COMPARTMENTS (OFFICER"S SIDE)
Roof hatch style compartments shall be provided the full length of the body, on the officer's side of
the body hose bed area and shall be designed as an integral extension of the lower side compartments
with a painted exterior finish. Drain tubes shall be provided at each end of each side compartment which
shall extend down through the lower compartments.
Each side roof compartment shall extend the length of the body, which shall be evenly divided into
three (3) individually accessed areas, which shall be open through from the front to the rear. The
compartment depth shall extend from the ceiling area of the upper side compartments to the top of the
body. The interior compartment width of each side roof compartment shall be a minimum of 13-1/2" inside
width with a 10" wide access door at the top.
Each roof compartment shall be equipped with an overlapping, hinged lift up tread plate door.
These doors shall be constructed of 3/16" aluminum tread plate with a 15 degree break on all sides. Each
door shall have two (2) gas shock style stay open devices which shall also retain the door in the closed
position. Each compartment door shall be equipped with a compartment light, a door button switch and a
floor drain with a plastic tube to direct the water below the body.
Protective panels shall be applied inside the compartments to cover any exposed wiring or
recessed side body lighting, provided on the unit. These panels shall reduce the overall usable
compartment area in the compartments.
ROLL-UP DOORS
Roll-up doors shall be provided on all compartments. The roll-up doors shall be constructed from
aluminum extruded slats which shall have a flexible seal between each slat for proper sealing of the door.
A synthetic rubber seal shall be provided at each side, top and bottom edge of the door to prevent
entry of dirt into the compartment.
The door shall be equipped with a lift bar style latch mechanism which shall latch at the bottom of
the door mounting extrusion.
The roll-up door assembly shall be furnished with a spring-loaded, counter balance assembly to
assist in door actuation.
All running board and high side air pack compartments shall be equipped with roll-up doors.
Allen Volunteer Fire Co., Inc. Tanker Specification
91
Antietam Fire Apparatus, Inc.
ROBINSON ROLL-UP DOORS
The roll-up doors shall be Robinson (ROM) brand roll-up doors. The doors and tracks shall be
painted to match the required color of the fire department.
A total of eight (8) painted doors shall be provided.
BEAVERTAILS
The rear body beavertail area shall be furnished with a squared off appearance to maximize the
available compartment area, while providing added support to the rear step support structure. The
beavertail panels shall be assembled in conjunction with the rear body corner panels. This assembly shall
provide a vertical mounting surface for tail lights at the rear most portion of the body and additional storage
space.
The inside of the beavertails shall be furnished with polished aluminum tread plate overlays.
COMPARTMENT TOPS
Compartment tops shall be covered with polished aluminum tread plate on both sides.
DRIP MOLDING
Compartment tops over all side compartments shall have a 45 degree flange formed out to provide
protection against water run off. A secondary extruded drip molding shall be provided between low
compartments and auxiliary high side compartments, when auxiliary compartments are provided.
FASTENERS
All exterior fasteners used for holding panels or tread plate shall be stainless steel. In no case
shall pop rivets or self-tapping screws be used.
COMPARTMENT LOUVERS
Machine stamped ventilating louvers shall be furnished in each compartment, and so located that
water cannot normally enter the compartment.
A perforated, polished, stainless steel grille shall be furnished between compartments for
ventilation in the event that the compartment configuration does not allow louvers to ventilate to the
atmosphere.
ACCESS PANELS
Removable access panels shall be provided in all lower compartments to access spring pins, fuel
Allen Volunteer Fire Co., Inc. Tanker Specification
92
Antietam Fire Apparatus, Inc.
tank sender, electrical junction compartment and rear body mounts.
Protective panels shall be located in the rear compartments providing access to the lights and
associated wiring. The covers shall also serve as protective covers to prevent inadvertent damage to
lights or wiring from tools or equipment located in the compartment.
REAR BODY PANEL
The rear body panel shall be fabricated from a minimum of 3/16" polished aluminum tread plate
and shall extend the full width between the beavertails. This panel shall be full height from the rear step to
the hose bed floor. The panel shall be bolted on and removable, with no part of the rear panel attached to
the booster tank.
REAR STANCHIONS - CAST ALUMINUM
Two (2) Cast Products Model #LB0029-1, polished stanchion brackets with wiring protectors, shall
be provided at the rear of the body for upper rear warning light mounting, one (1) each side. These
brackets shall be bolted to the sides of the body to minimize rear vehicle height.
BODY RUB RAILS
Sacrificial aluminum tread plate rub rails shall be mounted at the base of the body, extend outward
a minimum 3/4", downward 2" and flange inward 1". The rub rails shall extend the full length of the main
body and wrap around the rear body corners. Rub rails shall be designed to bolt to the body from the
bottom side of the compartment area, so as not to damage the body side panels on initial impact and to
provide for ease of replacement.
RUNNING BOARD STEPS
The driver and officer running board steps shall be fabricated of 3/16" polished aluminum tread
plate. The outside edge on each step shall be fabricated with a double break, return flange. The steps
shall be rigidly reinforced with a heavy duty support structure. The running boards shall not form any part
of the compartment design, and shall be bolted into place with a minimum 1/2" clearance gap between any
panel to facilitate water runoff.
OFFICER SIDE RUNNING BOARD STORAGE WELL
A storage well, constructed of 1/8" aluminum with a slatted aluminum bottom, shall be recessed
into the officer’s side running board. The storage well shall measure 9" deep x 9" wide x as long as
possible between the running board support members. Drain holes shall be located in the bottom corners
to allow water to drain from the storage well.
One (1) hinged, latched, aluminum tread plate cover shall be installed on the storage well located
in the officer's side running board.
Allen Volunteer Fire Co., Inc. Tanker Specification
93
Antietam Fire Apparatus, Inc.
The tread plate hose well cover shall have a notch cut out to allow pre-connection of
suction/discharge hose.
REAR STEP
The rear step shall be sixteen (16) inches deep, with twelve (12) inches recessed between the rear
portion of the rear side compartments and an additional four (4) inches extended beyond the rear of the
body. The step shall be fabricated from 3/16" polished aluminum tread plate, and shall be rigidly
reinforced. The recessed portion of the step shall be 52" wide.
The rear edge of the step shall be designed to accommodate the rear clearance lights, recessed
for protection in the step reinforcement channel. This step shall be bolted into place with a minimum 1/2"
clearance gap between it and the body panel.
INTERMEDIATE REAR STEP
An eight (8) inch bolt on intermediate rear step, fabricated from 3/16" aluminum tread plate, shall
be installed. The step shall be a minimum of 8" deep x full width of the rear tailboard.
REAR STEP COMPARTMENT
One (1) rear step compartment shall be provided between the frame rails. This compartment shall
be as tall, wide and deep as possible in the given area. This shall vary based on frame width, frame height
and depth of rear cross member. The compartment shall have a hinged tread plate door with a D-ring
handle automotive latch.
GRAB RAILS
All hand rails shall be 1-1/4" outer diameter, polished aluminum, rubber insert type tubing,
designed to meet NFPA 1901 requirements.
Molded gaskets shall be installed between the handrail stanchion castings and body surfaces to
prevent electrolytic reaction between dissimilar metals and to protect paint.
GRAB RAIL LOCATIONS:
Two (2) vertical rails shall be mounted on the rear edge of the beavertails, one (1) each side.
One (1) horizontal, full width handrail shall be installed on the rear, below the level of the hose bed.
Two (2) 18" horizontal handrails shall be provided and installed one (1) on each side at rear top of
body.
Allen Volunteer Fire Co., Inc. Tanker Specification
94
Antietam Fire Apparatus, Inc.
FOLDING STEPS - FRONT OF BODY
Six (6) Austin Hardware Model FS-200 CHR large folding steps, made of high strength die cast
aluminum, with a textured chrome plate finish, minimum of 42 in² surface, conforming to NFPA-1901
requirements, shall be provided on the front face of the running board compartments, above running board
steps, three (3) each side. The steps shall be mounted to accommodate access to the body hosebed area
with a maximum of 18" height between each step.
FOLDING STEPS-REAR OF BODY
Six (6) Austin Hardware Model FS-200 CHR large folding steps, made of high strength die cast
aluminum, with a textured chrome plate finish, minimum of 42 in² surface, conforming to NFPA-1901
requirements, shall be provided on the rear of the body, three (3) each side. The steps shall be mounted
to accommodate access to the body hosebed area with a maximum of 18" height between each step.
SAFETY SIGN(S) AT REAR STEP AND CROSS WALKWAY(S)
Safety sign(s) shall be located on the vehicle at the rear step, and at any cross walkway(s), to warn
personnel that riding in or on these areas while the vehicle is in motion is prohibited.
REAR WHEEL WELL LINERS
Fully removable, bolt-in, 12 gauge stainless steel fender liners shall be provided. The wheel well
liners shall extend from the outer wheel well body panel, into the truck frame. Removable vertical splash
shields, inward of the wheels, shall be provided to give access to the hydraulic components. The
completely washable fender liners shall be designed to protect the front and rear compartments and main
body supports from road salts, dirt accumulation and corrosion. Fender liners which are welded in place or
are only partially removable shall not be considered.
REAR FENDERETTES
The tandem rear fenders shall be equipped with easily replaceable, polished stainless steel
fenderettes. The fenderettes shall be equipped with a rubber gasket molding between the body panel and
the fender. Integral welded crown type liners shall not be acceptable.
AIR BOTTLE STORAGE COMPARTMENTS
A total of four (4) SCBA air bottle storage compartments (8" high x 8" wide x 26" deep) shall be
inserted into the body fender area on a 5 degree pitch. The compartments shall be located with two (2) on
the driver side and two (2) on the officer side of the rear body fender panels. The lower portion of the
compartments shall be non-abrasive to absorb shock and help secure the bottle.
Each storage compartment shall be equipped with a polished stainless steel door.
Allen Volunteer Fire Co., Inc. Tanker Specification
95
Antietam Fire Apparatus, Inc.
MUD FLAPS
Heavy duty mud flaps shall be provided behind the rear wheels.
REAR TOW EYES
Two (2) painted tow eyes shall be furnished on the rear of the vehicle, extending through the rear
body panel. The tow eyes shall be made from plate steel and shall be bolted directly to the chassis frame
rails with grade 8 bolts. The tow eyes shall be smooth and free from sharp edges, and have a minimum
eyelet hole of 2-1/2". The tow eyes shall be painted.
HOSE BED
The hose bed shall be located directly above the booster tank and shall be free from all sharp
objects such as bolts, nuts, etc., to avoid damage to fire hose.
A 36" deep by width of the hose bed diamond deck cover will be hinged attached to the front edge
to prevent air from getting under the front folds of the hose load.
The hose bed storage area, shall have a minimum capacity of sixty (60) cubic feet, and shall
accommodate 2-1/2" or larger fire hose as required by the Purchaser. The hosebed depth shall be 10".
The hose bed shall be located directly above the booster tank and shall be free from all sharp
objects such as bolts, nuts, etc., to avoid damage to fire hose.
For added strength, rigidity and appearance, the hose bed side walls shall have the top edge
flanged outward two (2) inches and downward one (1) inch. In a similar fashion, the top edge of the front
wall shall be flanged inward two (2) inches and downward one (1) inch.
HOSE BED FLOORING
Flooring to be constructed from extruded aluminum and be properly spaced for ventilation. The
flooring shall be smooth and free from sharp edges to avoid hose damage. The hose bed floor shall be
removable to provide access to inner body framework.
HOSE BED PARTITIONS
Two (2) fully adjustable 3/16", brushed finish, aluminum hose bed partitions shall be provided.
Partitions shall be easily adjustable by means of unistrut channels located at the front and rear of the hose
bed. Partitions shall be removable for access to the booster tank.
CUSTOMER REQUIRED HOSE STORAGE CAPACITY
The apparatus hose bed shall be capable of storing the following customer specified hose loads.
In addition, the vehicle weight analysis shall be based off of this hoseload provided the specified hose load
Allen Volunteer Fire Co., Inc. Tanker Specification
96
Antietam Fire Apparatus, Inc.
exceeds NFPA minimum standards.
 200' of 2 1/2" attack hose
 1300' of 5" supply hose
 500' of 3" supply hose
VINYL HOSE BED COVER - 1/4 TURN FASTENERS
A hose bed cover shall be provided and installed. The cover shall be made from 22 ounce; heavyduty vinyl coated polyester fabric (TXN 226). The cover shall be sewn with ultraviolet resistant thread and
shall have 2" wide nylon webbing sewn around the perimeter to provide additional strength.
The cover shall be secured to the top front body flange with quarter-turn fasteners. The cover shall
be secured to the side body flanges with quarter-turn fasteners. A weighted flap shall be furnished on the
rear of the cover with two (2) bungee cords.
The Hypalon material shall be black in color.
ADJUSTABLE SHELVING
Compartment shelving shall be constructed of 3/16” brush finish aluminum with a 2” upward bend
at front and rear, and side supports. Shelving shall be vertically adjustable with spring nuts in aluminum
strut channel.
Adjustable shelves shall be located as follows:
One (1) in the driver front compartment
One (1) in the officer front compartment
One (1) in the driver rear compartment
One (1) in the officer rear compartment
One (1) in the officer front high side compartment
One (1) in the driver rear high side compartment
One (1) in the officer rear high side compartment
ROLL-OUT/ DROP DOWN TRAYS
The roll out/tilt tray shall consist of a 3/16” brushed aluminum finished aluminum tray with a
minimum 2” lip on all four sides. Heavy duty aluminum unistrut "C" channel tracking material shall be
utilized to securely fasten the slide tracks to the compartment walls, while allowing height adjustment.
The slide mechanism shall consist of a low-weight high-strength plastic to create a robust front
Allen Volunteer Fire Co., Inc. Tanker Specification
97
Antietam Fire Apparatus, Inc.
bracket to support the aluminum tray. The rear of the tip down tray shall be mounted on a slider with an
integral pivot plate. This slider and pivot plate shall be mounted inside an aluminum rail for maximum
strength. The tray shall be secured in the stowed position utilizing a quarter turn latch. The roll out/tilt tray
shallbe rated for 330# capacity.
Roll out/Tilt trays will be located as follows:
One (1) in the driver front high side compartment
One (1) in the officer front high side compartment
One (1) in the driver rear high side compartment
One (1) in the officer rear high side compartment
SWING OUT TOOL BOARD(S)
One (1) swing out tool board(s) shall be provided and mounted as directed by the fire department.
The tool board(s) shall be constructed 3/16" smooth aluminum allowing mounting of equipment on the
interior and exterior of the toolboard(s). The toolboard(s) shall be attached to a vertical hinge, which will
allow the toolboard(s) to swing open. Aluminum angles shall attach the hinge to unistrut tracking to allow
depth adjustments. A heavy duty thumb latch shall be provided to secure the toolboard(s) in the closed
position.
HOPPER FOR SPEEDY DRY
A hopper for (customer supplied) "Speedy Dry" material shall be provided with a fill tower and
access pipe valve. The hopper shall have no less than a 25 gallon capacity. The hopper will be located
on top of the body as space permits.
DRI-DECKING
Dri-Deck brand floor material shall be installed on all compartment floors. The Dri-Deck shall be
custom installed to provide a full floor coverage.
Floor matting material shall be provided on eight (8) specified shelf(s) or roll-out tray(s).
The compartment flooring color shall be black.
HYDRAULIC REEL
One (1) Hannay, Model 2016-17-18 electric rewind Hydraulic reel(s) with a capacity of 100 feet of
twin hydraulic hose shall be provided and mounted at a location determined by the customer.
One (1) Hannay 4-way stainless steel roller assembly(s) shall be provided on the specified
hydraulic reel(s). The roller assembly opening shall be the full width of the reel drum. Support brackets
Allen Volunteer Fire Co., Inc. Tanker Specification
98
Antietam Fire Apparatus, Inc.
for the roller assembly shall be bolted to the hose reel.
HYDRAULIC HOSE - FEED LINE 6'
One (1) 6' length(s) of twin hydraulic hose with quick-connect fittings and spring hose retainer shall
be provided to allow the reel(s) to be powered by the hydraulic power unit.
One hundred feet (100') of Holmatro, high pressure, twin hydraulic hose for Holmatro equipment
shall be provided on the hydraulic reel.
SPREADER HOLDER - 30 DEGREE SLANT MOUNTING
One (1) Heavy Duty 30 degree slant mounting limited space spreader holder, Zephyr 69 LS shall
be provided and installed with stainless steel hardware as specified by the customer.
CUTTER HOLDER - HOLMATRO
One (1) cutter holder(s) for the Holmatro tool(s), Zephyr model 78, free standing holder, edgewise
mounting, gravity and rubber safety hook, aluminum alloy casting, powder coat finish, shall be installed
with stainless steel hardware.
RAM HOLDER - HOLMATRO
One (1) ram holder(s) for the Holmatro tool, Zephyr model 103, aluminum alloy casting, stainless
steel speed pin retainer, powder coat finish shall be installed with stainless steel hardware as specified by
the customer.
AIR REEL(S)
One (1) Hannay, Model 1514-17-18 electric rewind, air reel(s) shall be mounted per customer
requirements. The reel shall be piped to an auxiliary tank on the chassis air system. A check valve shall
be provided to ensure the chassis air brake system is not affected.
One (1) 4-way stainless steel roller assembly(s) shall be provided on the specified air reel(s). The
roller assembly opening shall be the full width of the reel drum. Support brackets for the roller assembly
shall be bolted to the hose reel.
One hundred feet (100') of 3/8" I.D. Goodyear brand air hose with hose stop shall be provided on
the air reel.
Allen Volunteer Fire Co., Inc. Tanker Specification
99
Antietam Fire Apparatus, Inc.
120/240 VOLT ELECTRICAL SYSTEM TESTING
All line voltage wiring and permanently connected devices and equipment shall be subjected to a
dielectric voltage withstand test of 900 volts for one minute. The test shall be conducted between live parts
and the neutral conductor and between live parts and the vehicle frame with any switches in the circuits
closed. The test shall be conducted after all bodywork has been completed. The dielectric tester shall
have a minimum 500 VA transformer with a sinusoidal output voltage that can be verified.
Electrical polarity verification shall be made of all permanently wired equipment and receptacles to
determine that connections have been properly made.
OPERATIONAL TESTING
The apparatus manufacturer shall perform the following operation test and shall certify that the
power source and any devices that are attached to the line voltage electrical system are properly
connected and in working order.
The generator shall be started from a cold start condition and the line voltage electrical system
loaded to 100 percent of the nameplate voltage rating.
The following items shall be monitored and documented every 15 minutes:




The cranking time until the generator starts and runs.
The voltage, frequency, and amperes at continuous full rated load.
The generator oil pressure, water temperature, transmission temperature, hydraulic temperature,
and the battery rate charge, as applicable.
The ambient temperature and altitude.
The generator shall operate at 100 percent of its nameplate wattage for a minimum of two (2)
hours.
HYDRAULIC DRIVEN GENERATOR
The generator system shall be an Onan model CMHG 15000 GenSet, PTO/Hydraulic, rated at
15,000 watts, 125/63 amps @120/240 VAC, single phase generator. The generator shall maintain a 60
Hz frequency between 850 and 3000 rpm.
The generator shall consist of hydraulic motor, alternator, cooling fan and a heat exchanger in a
stainless steel housing. The reservoir shall be a 3-gallon hydraulic tank with an integral filter, gauge,
temperature switch, breather and fill port.
The Onan limited warranty covers virtually everything except routine maintenance for the first five
(5) years or the first 1000 hours of operation.
WIRING
The generator output conductors shall be 4 gauge and the output conductors shall be routed
Allen Volunteer Fire Co., Inc. Tanker Specification
100
Antietam Fire Apparatus, Inc.
through non-metallic conduit 1" in diameter.
DISPLAY
The digital Onan display shall be by FRC and shall display Hz, voltage, amperage, oil temperature
and hours. The meter shall be installed near the breaker panel.
GENERATOR PTO
A hot shift PTO shall be provided on the transmission for the Onan generator. The PTO shall be
controlled from the cab. The control shall include a PTO engagement switch and a PTO engaged indicator
light.
GENERATOR WARRANTY
The specified generator shall have a five (5) year or one thousand (1000) hour warranty as
provided by the generator manufacturer. A copy of the generator warranty shall be provided at time of
delivery.
The generator shall be mounted above the pump enclosure on the officer side.
Locating the generator greater than 144" from the main breaker panel may require the installation
of an additional power disconnecting means.
LOAD CENTER
The generator output line conductors shall be wired from the generator output connections to a
Square D, Model #QO124L125G breaker panel. The breaker panel shall be equipped with a properly
sized main breaker using two (2) of the twenty-four (24) spaces which leaves a total of twenty-two (22)
available spaces.
The generator output conductors shall be sized to 115% of the main breaker rating and shall be
installed as indicated in the wiring section.
Twenty-two (22) appropriately sized, 120 volt, circuit breakers shall be provided.
The breaker panel shall be located in an enclosed compartment as directed by the fire department.
WIRING METHODS
Wiring/conduit shall not be attached to any chassis suspension components, water or fuel lines, air
or air brake lines, fire pump piping, hydraulic lines, exhaust system components or low voltage wiring.
All wiring shall be installed at a minimum of 12 inches away from any exhaust piping and a
minimum of 6 inches from any fuel lines.
Allen Volunteer Fire Co., Inc. Tanker Specification
101
Antietam Fire Apparatus, Inc.
All wiring shall be securely clamped within 6 inches of any junction box and at a minimum of every
24 inches of run. All supports shall be of nonmetallic material or corrosion protected metal. All supports
shall not cut or abrade conduit or cable and shall be mechanically fastened to the vehicle.
All power supply assembly conductors, including neutral and grounding conductors, shall have an
equivalent amperage rating and shall be sized to carry not less than 115% of the main breaker rating.
All Type SO or Type SEO cable not installed in a compartment shall be installed in wire loom.
Where Type SO or Type SEO cable penetrates a metal surface, a rubber or plastic grommet or bushing
shall be provided.
The installation of all 120/240 wiring shall meet the current NFPA-1901 Standards (NO
EXCEPTIONS).
WIRING IDENTIFICATION
All line voltage conductors located inside the main breaker panel box shall be individually and
permanently identified. When prewiring for future power wiring installations, the non-terminated ends shall
be labeled showing function and wire size.
GROUNDING
The neutral conductor of the power source shall be bonded to the vehicle fame only at the power
source.
The grounded current carrying conductor (neutral) shall be insulated from the equipment grounding
conductors and from the equipment enclosures and other grounded parts. The neutral conductor shall be
colored white or gray.
In addition to the bonding required for the lower voltage return current, each body and driving/crew
compartment enclosure shall be bonded to the vehicle frame by a copper conductor. The conductor shall
have a minimum amperage rating of 115 percent of the name plate current rating of the power source
specification label.
CIRCUIT BREAKER/RECEPTACLE INSTALLATION
The system shall be installed by highly qualified electrical technicians to assure the required level
of safety and protection to the fire apparatus operators. When multiple circuit are required, the circuits
shall be wired to the breaker panel in a staggered configuration to minimize electrical loads on each
breaker or generator (leg) circuit. The wiring, electrical fixtures and components shall be to the highest
industry quality standards available on the domestic market. The equipment shall be the type as designed
for mobile type installations subject to vibration, moisture and severe continuous usage.
RECEPTACLE INSTALLATIONS
Any receptacle installed in a wet location must be a minimum of 24 inches above the ground and
Allen Volunteer Fire Co., Inc. Tanker Specification
102
Antietam Fire Apparatus, Inc.
provided with an approved wet location cover. Wet receptacles may not be mounted at more than 45
degrees from vertical, nor can they be mounted in a face-up position.
One (1) 110 volt, NEMA L5-20, 20 amp, Single twist-lock receptacle with a grey thermoplastic,
corrosion resistant, weatherproof cover shall be installed at each side of the front bumper extension end
caps. (Total of two (2))
Both receptacles shall require one (1) 20 amp, 110 volt circuit breaker to be installed in the load
center.
One (1) 110 volt, NEMA L5-20, 20 amp, Single twist-lock receptacle with a grey thermoplastic,
corrosion resistant, weatherproof cover shall be installed at each side of the of the rear body panel. (Total
of two (2))
Both receptacles shall require one (1) 20 amp, 110 volt circuit breaker to be installed in the load
center.
One (1) 110 volt, NEMA L5-20, 20 amp, Single twist-lock receptacle with a grey thermoplastic,
corrosion resistant, weatherproof cover shall be installed as directed by the fire department.
This receptacle shall require one (1) 20 amp, 110 volt circuit breaker to be installed in the load
center.
One (1) 110 volt, NEMA 5-15, 15 amp, duplex twist-lock receptacle with a grey thermoplastic,
corrosion resistant, weatherproof cover shall be installed as directed by the fire department.
The receptacle shall require one (1) 15 amp, 110 volt circuit breaker to be installed in the load
center.
ELECTRIC CORD REEL (220 VOLT)
One (1) Hannay Model #ECR-1620-17-18, with 4 conductor collector assembly for 220 volts, with
electric rewind cord reel shall be provided and wired to the breaker panel. The reel shall be securely
mounted and equipped with a rewind control adjacent to the reel.
The cord reel shall be mounted above the pump enclosure on the officer side.
The circuit breaker used to protect any device attached to the cord reel shall be sized to the
smallest electrical connection used.
ELECTRIC CABLE
Two hundred twenty five (225) feet of Type SO yellow 10/4 heavy duty electric cable, wired for 220
volt, shall be provided on the cord reel.
One (1) NEMA L14-20R, 20 amp, four prong twist-lock receptacle(s) shall be provided on the end
of the cable.
Allen Volunteer Fire Co., Inc. Tanker Specification
103
Antietam Fire Apparatus, Inc.
JUNCTION BOX(ES)
One (1) Extenda-Lite, four (4) outlet junction box(es) with one (1) NEMA 5-20R GFCI rated straight
blade receptacle and three (3) NEMA L5-20R twist-lock receptacles with a NEMA L14-20P twist-lock male
inlet shall be provided.
The junction box(es) shall be wired such that the four (4) outlets provide 120 VAC.
CABLE ROLLER ASSEMBLY
One (1) four (4) roller assembly(s) shall be provided adjacent to each cord reel to provide unobstructed deployment and rewinding of the cable.
One (1) cable ball stop(s) shall be installed on the cable to keep the cable end from passing
through the roller assembly.
LIGHTING (TELESCOPING) - REAR OF CAB
Two (2) Fire Research OPTIMUM, Model #OPA530 side mounted, push up scene light, deployable
in a full 360 degree rotation. The entire assembly shall be UL listed as Scene light for Fire Service Use,
manufactured by Fire Research. The tightening mechanism shall be of a twist lock (concentric ring)
design, the use of a knob or latch to release the pole in order to raise and lower the telescoping portion of
the pole shall not be accepted.
The lights shall be mounted on the rear of the cab, one (1) each side. Wiring used for the lighting
shall be a minimum of 16 gauge three (3) wire cable that is properly supported and protected from
damage.
Each Fire Research light shall be equipped with a 1500 watt model M15, Optimum lamp head. The
bulb shall be easily accessible through the front glass and frame. Changing the bulb should be easily done
from the front of the lamp head. The glass and frame must be removable, held onto the lamp assembly by
no more than four front screws.
Two (2) Model M15, 1500 watt light heads shall require one (1) 240V, 20 amp circuit breaker.
LIGHTING (TELESCOPING) - REAR OF BODY
Two (2) Fire Research OPTIMUM, Model #OPA530 side mounted, push up scene light, deployable
in a full 360 degree rotation. The entire assembly shall be UL listed as Scene light for Fire Service Use,
manufactured by Fire Research. The tightening mechanism shall be of a twist lock (concentric ring)
design, the use of a knob or latch to release the pole in order to raise and lower the telescoping portion of
the pole shall not be accepted.
The lights shall be mounted on the rear face of the body, one (1) each side. Wiring used for the
lighting shall be a minimum of 16 gauge three (3) wire cable that is properly supported and protected from
damage.
Allen Volunteer Fire Co., Inc. Tanker Specification
104
Antietam Fire Apparatus, Inc.
Each Fire Research light shall be equipped with a 1500 watt model M15, Optimum lamp head. The
bulb shall be easily accessible through the front glass and frame. Changing the bulb should be easily done
from the front of the lamp head. The glass and frame must be removable, held onto the lamp assembly by
no more than four front screws.
Two (2) Model M15, 1500 watt light heads shall require one (1) 240V, 20 amp circuit breaker.
LIGHTING (RECESSED RIGHT SIDE OF BODY)
Two (2) Fire Research Optimum Model OPA200 recessed lights shall be installed, one rearward
and one forward on the right side of the body. The recess casting shall incorporate internal heat
dissipating fins. The housing shall incorporate internal heat-dissipating fins and have cutout dimensions
not to exceed 2" deep by 4 1/4" high by 9 3/4" wide. The lamp head shall protrude no more than 3 1/8"
from the housing flange. Wiring shall extend from the bottom of the recessed housing.
Wiring used for the lighting shall be a minimum of 16 gauge three (3) wire cable that is properly
supported and protected from damage.
Each lamp head shall have one (1) quartz halogen M10, 1000 watt 120 volt bulb. Each bulb shall
draw 8.3 amps and generate 22,000 lumens. The bulb shall be accessible through the front. The lamp
head shall incorporate a vacuum deposit polished reflector to produce a uniform beam that lights up an
area 100° vertically by 150° horizontally. The lamp head shall have a heat dissipating curved front lens.
The curve of the lens shall have a radius of 5.16 inches to optimize light emission.
Two (2) Model M10, 1000 watt light heads shall require one (1) 120V, 20 amp circuit breaker.
LIGHTING (RECESSED LEFT SIDE OF BODY)
Two (2) Fire Research Optimum Model OPA200 recessed lights shall be installed, one rearward
and one forward on the left side of the body. The recess casting shall incorporate internal heat dissipating
fins. The housing shall incorporate internal heat-dissipating fins and have cutout dimensions not to exceed
2" deep by 4 1/4" high by 9 3/4" wide. The lamp head shall protrude no more than 3 1/8" from the housing
flange. Wiring shall extend from the bottom of the recessed housing.
Wiring used for the lighting shall be a minimum of 16 gauge three (3) wire cable that is properly
supported and protected from damage.
Each lamp head shall have one (1) quartz halogen M10, 1000 watt 120 volt bulb. Each bulb shall
draw 8.3 amps and generate 22,000 lumens. The bulb shall be accessible through the front. The lamp
head shall incorporate a vacuum deposit polished reflector to produce a uniform beam that lights up an
area 100° vertically by 150° horizontally. The lamp head shall have a heat dissipating curved front lens.
The curve of the lens shall have a radius of 5.16 inches to optimize light emission.
Two (2) Model M10, 1000 watt light heads shall require one (1) 120V, 20 amp circuit breaker.
Allen Volunteer Fire Co., Inc. Tanker Specification
105
Antietam Fire Apparatus, Inc.
CAB BROW LIGHTING
Two (2) Fire Research OPTIMUM, Model #OPA800 contour mount brow light(s) shall be provided.
The entire assembly shall be UL listed as Scene light for Fire Service Use, manufactured by Fire
Research.
The light(s) shall be mounted on the upper forward face of the cab. Wiring used for the lighting
shall be a minimum of 16 gauge three (3) wire cable that is properly supported and protected from
damage.
The Fire Research light shall be equipped with a 1000 watt Model M12, Optimum lamp head. The
bulb shall be easily accessible through the front glass and frame. Changing the bulb should be easily
done from the front of the lamp head. The glass and frame must be removable, held onto the lamp
assembly by no more than four front screws.
One (1) Model M12, 1000 watt light head shall require one (1) 240 V, 15 amp circuit breaker.
QUARTZ LIGHTS REAR OF CAB SWITCHING
The quartz lights on the rear of the cab shall be wired through the circuit breaker panel and
switched at the cab dash or overhead. The control switches shall be wired through low voltage relays to
maintain 12 volt circuits in the cab.
QUARTZ LIGHTS REAR OF BODY SWITCHING
The quartz lights on the rear of the body shall be wired through the circuit breaker panel and
switched at the cab dash or overhead. The control switches shall be wired through low voltage relays to
maintain 12 volt circuits in the cab.
QUARTZ LIGHTS RIGHT SIDE OF BODY SWITCHING
The quartz lights on the right side of the body shall be wired through the circuit breaker panel and
switched at the cab dash or overhead. The control switches shall be wired through low voltage relays to
maintain 12 volt circuits in the cab.
QUARTZ LIGHTS LEFT SIDE OF BODY SWITCHING
The quartz lights on the left side of the body shall be wired through the circuit breaker panel and
switched at the cab dash or overhead. The control switches shall be wired through low voltage relays to
maintain 12 volt circuits in the cab.
BROW LIGHT SWITCHING
The quartz light above the windshield shall be wired through the circuit breaker panel and switched
at the cab dash or overhead. The control switches shall be wired through low voltage relays to maintain
Allen Volunteer Fire Co., Inc. Tanker Specification
106
Antietam Fire Apparatus, Inc.
12 volt circuits in the cab.
Allen Volunteer Fire Co., Inc. Tanker Specification
107
Antietam Fire Apparatus, Inc.
LADDER STORAGE
The ground ladders shall be stored horizontally within a sleeve in the water tank.
LADDERS
The following Alco-Lite ground ladder compliment shall be provided:
One (1) Alco-Lite Model PEL-24; 24', aluminum, two (2) section extension ladder.
One (1) Alco-Lite Model PRL-14; 14', aluminum, straight roof ladder with folding hooks.
One (1) Alco-Lite Model FL-10; 10', folding, aluminum, attic ladder.
PIKE POLE STORAGE
Three (3) pike pole tube(s) shall be provided. Each holder shall be equipped with a spring type
holder and shall be accessible from the rear of the apparatus. Each pike pole holder shall be labeled to
indicated the pike pole length.
The pike pole tube(s) shall be mounted in the ladder storage compartment.
PIKE POLES
Three (3) Fire Hooks Unlimited pike poles shall be provided in the following configuration:



1 - Six (6) foot pike poles with fiberglass handles
1 - Eight (8) foot pike poles with fiberglass handles
1 - Twelve (12) foot pike poles with fiberglass handles
SUCTION HOSE STORAGE
The suction hoses shall be located under the water tank one (1) on the driver’s side and one (1) on
the officer side of the apparatus.
SUCTION HOSE
Two (2) 15' sections of six (6) inch Maxi-Flex (PVC) suction hose with lightweight hard coat
couplings shall be furnished. Couplings shall include a long handle, female swivel on one end and a
rocker lug male on the other end. All threads shall be six (6) inch N.S.T.
NOTE: All PVC suction hoses are strictly drafting hoses and must not be used on hydrants or in
pressure applications, as serious personal injury or death may occur.
Allen Volunteer Fire Co., Inc. Tanker Specification
108
Antietam Fire Apparatus, Inc.
STRAINER
One (1) 6" NST barrel type strainer(s) shall be provided to attach to the suction hose. A
compartment mounting bracket shall also be provided to store the strainer(s) when not in use.
HYDRANT ADAPTER
A double female swivel hydrant adapter shall be provided along with a screw base mounting
bracket. One end shall attach to the suction hose and the other end to be 4-1/2" N.S.T. thread.
ADDITIONAL ITEMS SUPPLIED WITH THE VEHICLE


1 - Pint of touch up paint for each color
1 -Bag of assorted stainless steel nuts and bolts
WHEEL CHOCKS
Two (2) ZICO #SAC-44 wheel chocks shall be mounted forward of the rear wheels on the driver
side below the side running board compartments.
Allen Volunteer Fire Co., Inc. Tanker Specification
109
Antietam Fire Apparatus, Inc.
PAINT, PREPARATION AND FINISH
The PPG Delta, Low V.O.C., polyurethane finishing system, or equal, shall be utilized. A "Clear
Coat" paint finish shall be supplied to provide greater protection to the quality of the exterior paint finish.
All removable items, such as brackets, compartment doors, etc. shall be painted separately to
insure finish paint behind mounted items. All compartment unwelded seams exposed to high moisture
environments shall be sealed using permanent pliable caulking prior to finish paint.
BODY PRIMER & PREPARATION
All exposed welds shall be ground smooth for final finishing of areas to be painted. The
compartments and doors are totally degreased and phosphatized. After final body work is completed,
grinding (36 and 80 grit), and finish sanding shall be used in preparation for priming.
BODY FINISH PAINT
The body shall be finish sanded and prepared for final paint. Upon completion of final preparation,
the body shall be painted utilizing the highest quality, state of the art, low V.O.C., polyurethane base paint.
Finish paint shall be applied in multiple coats to ensure proper paint coverage with a high gloss finish.
The entire body shall be buffed and detailed.
BODY PAINT
The inside and underside of the complete body assembly shall be painted job color prior to
installation of the body on the chassis or torquebox.
COMPARTMENT PAINT
The interior of the compartments shall be finish painted with Zolatone #20-63 Marble Stone scuff
resistant paint to provide a protective application over all of the compartment interior surfaces.
BODY PAINT
The body paint finish shall be PPG Delta System in a single color, to match customer furnished
paint codes and requirements.
PUMP / PIPING PAINT
The pump enclosure and pump/plumbing within the pump enclosure shall be painted job color to
match the primary color of the body.
Allen Volunteer Fire Co., Inc. Tanker Specification
110
Antietam Fire Apparatus, Inc.
CAB PRIMER & PREPARATION
The cab primer shall be a two (2) stage process. First stage shall be a coating with a two part
component, self etching, corrosion resistant primer to chemically bond the surface of the metal for
increased adhesion. Second stage shall be multiple coats of a catalyzed, two component polyurethane
primer applied for leveling of small imperfections and top coat sealing.
CAB FINISH PAINT
The entire cab shall be finish sanded and prepared for final paint. Upon completion of final
preparation, the cab shall be painted utilizing the highest quality, state of the art, low V.O.C., polyurethane
base paint. Finish paint shall be applied in multiple coats to ensure proper paint coverage with a high
gloss finish.
The cab exterior shall be painted with PPG Delta system to match purchaser's furnished paint
codes. A two-tone paint finish shall be provided with the two-tone break line located approximately 3"
below the cab side windows.
The entire exterior finish of the cab shall be buffed and detailed.
CAB INTERIOR PAINT
The interior metal surfaces of the cab shall be finish painted with a textured gray paint.
CHASSIS PAINT
The chassis frame rails, suspension and axles shall be painted black with a Polyurethane base
paint prior to installation of any air lines or electric systems to ensure proper serviceability.
WHEEL PAINT
The chassis wheels, (except polished aluminum wheels) shall be painted job color with silver trim
around the perimeter.
PAINT CODES
The paint shall match customer furnished paint code(s) and layout. The paint code(s) shall be as
indicated below:

PRIMARY PAINT COLOR
Single Color:

TBD
Paint Code#
TBD
SECONDARY PAINT COLOR
Allen Volunteer Fire Co., Inc. Tanker Specification
111
Antietam Fire Apparatus, Inc.
Two/Tone Color:
TBD
Paint code#
TBD
TOUCH-UP PAINT
One (1) pint of each exterior color paint for touch-up purposes shall be supplied when the
apparatus is delivered to the end user.
FINALIZATION & DETAILING
Prior to delivery the vehicle, the interior and exterior be cleaned and detailed. The finalization
process detailing shall include installation of NFPA required labels, checking fluid levels, sealing and
caulking required areas of the cab and body, rust proofing, paint touch-up, etc.
RUST PROOFING
The entire unit shall be thoroughly rust proofed utilizing rustproof and sound deadening materials
applied in manufacturer recommended application procedures. Rust proofing shall be applied during the
assembly process and upon completion to insure proper coverage in all critical areas.
COMPUTER GENERATED LETTERING
The lettering and striping shall be custom designed utilizing state of the art computer software and
computerized cutting machines. The manufacture shall employ a full time artist / designer to generate all
lettering, decals, and striping to meet the requirements of the Fire Department. The artwork for the
lettering and striping shall be kept on record by the apparatus manufacturer to allow for ease in duplication
for the Fire Department.
FRONT CAB DOOR LETTERING
Gold leaf, "Sign Gold", with drop shadow lettering shall be provided on the cab driver's and
officer's doors per the fire department requirements. The design of the lettering on the cab doors shall be
designed to fit in the 496 sq. inches available.
Lettering provided on the driver's and officer's cab doors shall be 3" high.
COFFIN COMPARTMENT LETTERING
Gold leaf, "Sign Gold", with drop shadow lettering shall be provided on the coffin compartment per
the fire department requirements. The design of the lettering on the coffin compartment shall be designed
to fit in the 2500 sq. inches available.
Lettering provided on the coffin compartment shall be 8" high.
Allen Volunteer Fire Co., Inc. Tanker Specification
112
Antietam Fire Apparatus, Inc.
LETTERING FONT
The lettering shall be designed and cut with a basic block type font:
"BLOCK TYPE FONT"
SCOTCH-LITE STRIPE
A six (6) inch high "Scotch-Lite" stripe shall be provided. The stripe shall be applied on a minimum
of 60 percent of each side of the unit, 60 percent on the rear of the unit and 40 percent on the front of the
unit. The ScotchLite stripe layout shall be determined by the Fire Department.
The Scotch-Lite shall be white in color.
REAR CHEVRON STRIPING
At least 50% of the rear facing vertical surface shall be covered with alternating strips of reflective
striping.
The striping shall be 6" ScotchLite.
The Scotch-Lite shall be Red and Yellow in color.
Allen Volunteer Fire Co., Inc. Tanker Specification
113
Antietam Fire Apparatus, Inc.
VEHICLE WARRANTY
The proposed vehicle includes a one (1) year new vehicle warranty, upon delivery and acceptance
of the vehicle. The warranty will ensure that the vehicle has been manufactured to the proposed contract
specifications and will be free from defects in material and workmanship that may appear under normal
use and service within the warranty period. The warranty may be subject to different time and mileage
limitations for specific components and parts. This warranty is issued to the original purchaser of the
vehicle.
The warranty will not apply to tires, batteries, or other parts or components that are warranted
directly by their manufacturers. The warranty will not apply to routine maintenance requirements as
described in the service and operator's manual. No warranty whether express, implied, statutory or
otherwise including, but not limited to any warranty of merchantability or fitness for purpose will be
imposed.
COMPONENT WARRANTY INTERVALS
OVERALL UNIT AND CUSTOM CHASSIS
All components and parts of the vehicle are warranted for a period of one (1) year from acceptance
of the vehicle, unless excluded elsewhere in this warranty or described as having longer time limitations.
ENGINE WARRANTY
The unit will be equipped with a Fire Service rated engine, which will come furnished with a five (5)
year Engine Manufacturer's warranty. A copy of the manufacturer's warranty will be supplied to define
additional details of the warranty provisions.
TRANSMISSION WARRANTY
The required Allison transmission shall be provided with a five (5) year warranty. A copy of the
Allison transmission warranty shall be supplied to the purchaser to define additional details of the warranty
provisions.
CUSTOM CHASSIS FRAME RAILS
The proposed KME custom chassis frame and cross members will be warranted for an unlimited
time period. A copy of KME's frame rail warranty will be supplied to define additional details of the
warranty provisions.
CROSSMEMBERS WARRANTY
A lifetime warranty will be provided on all chassis frame crossmembers.
MERITOR AXLE WARRANTY
The Meritor axle/s will be provided with a two (2) year parts and labor warranty. The wheel seals,
gaskets and wheel bearings will have a one (1) year warranty. A copy of Meritor's warranty will be supplied
to define additional details of the warranty provisions.
Allen Volunteer Fire Co., Inc. Tanker Specification
114
Antietam Fire Apparatus, Inc.
CAB STRUCTURE WARRANTY
The proposed cab will be warranted against structural defects for a period of ten (10) years from
the date of acceptance of the unit. Details of warranty coverage, limitations and exclusions are included in
the specific warranty document.
BODY STRUCTURE WARRANTY
The proposed body will be warranted against structural defects for a period of ten (10) years from
the date of acceptance of the unit. Details of warranty coverage, limitations and exclusions are included in
the specific warranty document.
CORROSION WARRANTY
The proposed cab and body will be warranted against rust-through or perforation, due to corrosion
from within, for a period of ten (10) years. Perforation is defined as a condition in which an actual hole
occurs in a sheet metal panel due to rust or corrosion from within. Surface rust or corrosion caused by
chips or scratches in the paint are not covered by this warranty.
PAINT FINISH WARRANTY
The paint finish will be warranted for a period of seven (7) years from the date of acceptance of the
unit. Details of warranty coverage, limitations and exclusions are included in the specific warranty
document.
WATER TANK (LIFETIME)
The proposed water tank will be warranted by the water tank manufacturer for the "Lifetime" of the
unit. A copy of the manufacturer's warranty will be supplied to define additional details of the warranty
provisions.
HALE FIRE PUMP Limited Standard Warranty
Hale Products, Incorporated ("Hale") hereby warrants to the original buyer that products
manufactured by Hale are free of defects in material and workmanship for a period of five(5) years from
the date product is first placed into service of five and one-half(5 1/2) years from date of shipment by Hale,
whichever period shall be first to expire. Within this warranty period Hale will cover parts and labor for the
first two(2) years and parts only for years three(3) through five(5).
Allen Volunteer Fire Co., Inc. Tanker Specification
115