UAB “Teltonika”
Kauno padalinys
WiMAX Reikalavimų formavimas integravimui bei maketams
General requirements
The unit shall support auto installation and handover support. The device installation shall be
designed in such way that it would not need any assistance technical personnel when installing
device at user’s home.
The device shall support standard IP Protocols (i.e. TCP, UDP, DNS, FTP, SMTP, POP3, HTTP).
The device shall support handover for implementing mobility feature.
Enclosure requirements
Environment
Router is intended to use in home environment.
Operating temperature: 0 -50 °C
Storage temperature: -20 °C -70 °C
Humidity (no condensation): 0% -90%
The device enclosure shall be compact and rugged to withstand harsh environment conditions.
Enclosure shall take up minimal and have brackets for wall fixing. The enclosure shall have an
operator marking capability.
The proposed enclosure is presented in Figure 1.
The device state indication LED icons shall be on the front panel. LED icons shall be easy to
understand for the end user in order to indicate the state of the device
LED:
1 x Power indication
5 x WiMAX connection status indication
1 x WLAN indication (optional)
Interface connections
Power Jack
Reset Key
1xLAN RJ45
2xSMA WiMAX connectors (min distance between antennas at least 30 mm)
2xRP-SMA WLAN connectors (optional, min. distance between antennas: 30 mm)
Power supply requirements
The external power supply voltage shall be in range from 9V to 18V.
The average power consumption in worst case scenario shall be 10W, peak: 15W.
AC/DC wall adapter requirements:
110 -220 Vac AC +/-10% @ 60Hz regulated, with flat-prong male plug
AC Power Supply must not be bulky and heavy to support wall mount connection
WiMAX
Standard Compliance: IEEE 802.16e-2005 Mobile WiMAX
Modulation: Scalable OFDMA Wave 2 Compliant; QPSK, 16QAM, 64QAM (DL)
Duplexing Mode: TDD
Max Data Rate: Up to 20Mbps (DL), 5Mbps (UL);
Frequency bands: 3.5GHz
Channel Bandwidth: 3.5Mhz, 7MHz, 10MHz, 20MHz
RF Output Power: Max. 23dBm
MIMO: MIMO A (STC); MIMO B (SM)
FFT: 512/1024/2048 points FFT
Authentication: EAP-TLS, EAP-TTLS, PKMv2
Encryption: AES, DES, 3DES
WiMAX QoS: UGS, rt-VR, ert-VR, nrt-VR, BE
Interface requirements
LAN Ethernet Interface: 10/100 BASE-T (RJ-45) with Auto MDIX
LED: Power, WiMAX Network Activity/WiMAX RSSI, LAN Activity
Reset Button (reset device and reset to factory default settings)
WiMAX: Female 2xSMA RF Antenna connector
WLAN 802.11b/g (optional)
WLAN Female 2xRP-SMA RF Antenna connector (optional)
Network requirements
General network requirements
Auto-connect/Auto-Reconnect
Local network settings (Gateway, IP address, DNS server)
DHCP server
Universal Plug and Play (UPnP) (optional)
QoS / traffic shaping (optional)
Firewall
NAT
Port forwarding
Static routing (optional)
DMZ (optional)
Access Control Lists (IP filtering) (optional)
IP-Hostname Filtering (optional)
URL Filtering (filtering by keyword) (optional)
Packet Filter (optional)
Installation, maintenance, management (IMM)
The RUT200 must be maintenance free, which means that the end user does not need to perform
any maintenance.
The device must support configuration via WEB based graphical user interface (GUI).
The device shall support OMA-DM management protocol. It shall allow WiMAX service provider
remotely upgrade device’s firmware and configure WiMAX connection settings.
The additional configuration shall be implemented via SSH (CLI).
The WEB GUI shall allow following IMM features:
Connection status indication (WAN, LAN)
Local and remote Firmware Upgrade:
FW Upgrade via WEB GUI
FW Upgrade OMA-DM
FW Upgrade via Secure Shell (SSH) (optional)
Advanced troubleshooting-system log (levels: info, debug)
Login password change
Restoring Default Settings via CLI or WEB GUI
Wizard Set-up (optional)
Traffic Log (WAN inbound/outbound) (optional)
System Up Time (optional)
Monitoring Connections (optional)
Backup settings (saving config file) (optional)
Virtual private network (optional)
IPsec, PPTP, L2TP pass-through (optional)
IPsec server/client (IKE) (optional)
Open VPN server/client (optional)
Additional programs
Ping-reboot (optional)
DDNS (optional)
L.E.P Kauno padalinio vadovas
Algirdas Dagilis
2009 m. Rugpjūčio 31 d.