3G WiFi Mobile Power/Router
Quick Install Manual
It is a consumer electronic 3G network product, different functional in one: 3G route, wireless
route, ADSL dial-up Internet connection, wireless network storage and mobile power, makes you
enjoy the wireless surfing and share the wonderful contents in your digital devices anytime and
anywhere. Including functions as follows:
*3G route: support the 3G wireless network card dial and bandwidth sharing of WCDMA/CDMA
2000/TD-SCDMA systems.
*Wireless route: support the traditional wired broadband network ADSL dial, dynamic network
and static network access.
*Wireless network storage: support U disk, USB HDD file reading and sharing, and online movie
on demand.
*Mobile power: can charge iPhone, iPad, Android cellphones, tablets and other mobile digital
devices.
Wireless relay: realize the relay and amplification of signals in order to expand the cover range of
the wireless network.
1. Accessories list
1. Host
2. USB cable
3. User manual/Warranty card
4. Qualification
2. Panel introduction
Hardware Port
Function Description
Boot, can boot the router.
Power switch
Charge, boot mobile power function, can charge external
devices through the USB port.
Power off, close this router.
Power indicator button
Display the current battery power, the power indicator is
divided into four levels.
USB port
Can connect the 3G USB network card of WCDMA / CDMA
2000 / TD-SCDMA systems, U disk, USB HDD, or can charge
Android cellphones, tablets, PSP and so on.
DC charge port
DC 5V input, this device can be charged through the Micro
USB cable.
Charge indicator
While charging this device, the indicator keeps on.
RJ45 Ethernet port
WAN port: under Dynamic IP/Static IP/PPPoE modes, this port
is used as WAN port to connect the hotel wired network, LAN
broadband, xDSL Modem/Cable Modem.
Restore factory setting
Long press 5 seconds this key and the release when the route is
on, the router will restore factory setting.
2.2 Status Indicator Description
Operation
Indicator status
Boot
Blue light always on
Push the switch to “On”, it means normal
boot when the blue light always on.
Insert
mobile
storage device
Blue
light
slow
flashing (1.5s once)
Insert the U disk, HDD into the USB port,
after 8-10s, if blue light slow flashing, ot
means mobile storage device normal loading.
Blue light always on
Fail to load.
Blue
light
fast
flashing(0.5s once)
Wait for 39s, if Blue light fast flashing(0.5s
once), it means entering into 3G dial status.
Blue
light
slow
flashing (1.5s once)
Blue light slow flashing (1.5s once), it means
successful 3G dial, can visit Internet..
Blue light always on
Unsuccessful dial.
Green light always on
After 5s, if green light always on, it means
normal network cable connection.
Insert 3G card
Description
Insert
ADSL
network cable
Blue
light
slow
flashing (1.5s once)
Insert
router
network
cable
(under Dynamic
IP mode)
A while after the green light always on, if
blue light slow flashing, it means successful
ADSL dial, can visit the Internet.
Green light always on
Normal network cable connection.
Green
light
slow
flashing (1.5s once)
Normal network cable connection, and
means that the router successfully gain the
dynamic IP address from last router.
Insert
router Green light always on
network
cable
(under Static IP
mode)
Normal network cable connection.
3. Application Scenarios
It supports the following application modes:
1). 3G-to-WiFi sharing surfing mode.
2). Wired-to-WiFi sharing surfing mode.
4. Mobile power function: description of charging cellphones, tablets and other digital
devices.
First step: Battery power display:
A. Press the power indicator button, the battery power indicator will be on, then can see the
current power percentage, the light will be off after 4s in order to save the power.
B. The corresponding relation of battery power and power indicator:
Indicator status
Description
Battery power
indicator
All lights off
No power, please charge this device
1 light on
Less than 25% power
2 lights on
25% to 50% power
3 lights on
50% to 75% power
4 lights on
75% to full power
Second step: charge cellphones, tablets and other digital devices.
Push the switch to Charge Function gear(C gear) can boot moble power function, insert the charge
cable of the digital product into its USB port, then can charge iPad, iPhone, Android smart
cellphones and other mobile digital devices.
Prompt: it is better to use the cellphone original charge cable, so can realize the best charge effect.
5. Charge itself:
When its battery is being out of power, it can be charged through the following ways.
*Power charge: connect one port of the Micro USB cable to its DC charge port (Micro USB port),
the other port connects to the adapter’s USB port.
*PC USB charge: connect one port of the Micro USB cable to its 5 DC charge port (Micro USB
port), the other port connects to the PC USB port to charge this device.
Charge Attentions:
1. Better to use the charge adapter of 5V output (600 to 1000mA output current), including the
common iPhone, iPad charge adapter.
2. Charge time: 5V 1000mA charge plug: about 5-8 hours; 5V 600mA charge plug: about 11
hours; Direct charging through PC USB: over 12 hours.
3. During charging, must not use this device to charge other devices in order to protect the
battery and extend its use life.
6. Functions and Configuration of 3G WiFi wireless router
It supports visiting and configuring through web browser mode, we can use the common
Microsoft IE browser, iPhone Safari browser and the built-in browser of Android system to log
onto the router, to view the content of the mobile storage device, configure the parameter of the
router.
6.1 Wireless client devices first need to connect wireless router (take iPad as an example)
Step1: open the iPad main interface, choose “Setup”→”WLAN”, to enter WiFi setup interface,
open the wireless switch, iPad will automatically scan the surrounding wireless network, we can
find router of “3G WiFi xxx” SSID name, double click to connect.
Step2: During connection, input the WiFi password on the back of the router shell to make
connection (the password can be altered).
Step3: see and set the network parameters, click the “>” button right on the connected wireless
signal, it will pop up the wireless connection network parameter setup interface. (DHCP server
opening by default, it is better to use DHCP.)
6.2 Enter the configuration interface of 3G WiFi router
Click Safari browser, input “http://192.168.169.1” on the address bar, click Go, then can enter
the interface of the router.
Besides, aiming at the users of iPhone, iPad and other ios devices, we can directly input “wd”
on the address bar and then click Go.
6.3 Change the WiFi password
The factory setting WiFi password is rather simple, remember to change the WiFi password
during first use in order to ensure the data safety.
Changing method:
Click the WiFi Safety icon to enter WiFi safety setup interface.
6.4 Set up the 3G surfing parameter
After inserting the 3G wireless network card into the router’s USB port, it will automatically
carry out 3G dial surfing.
Click “3G” icon to enter 3G configuration interface, choose the model of 3G network card, in
the dial setting, choose boot dial mode, input the dial parameter provided by 3G ISP, click OK,
auto recognition mode by default, plug and play, needs no modification.
6.5 Set up the wired broadband surfing parameter
Under wired WiFi mode, it is used as a wireless router, the Ethernet port as WAN port, all
wireless terminals can only connect to the router through WiFi to surf Internet.
Click “Network setting” - “WAN”, choose the surfing mode according to the front end
broadband, supports 3 common wired surfing modes: static IP, dynamic IP, PPPoE.
A. Static IP
If the access mode is static IP that the network provider gives, you needs to input ISP or ask the
administrator to give you a IP address, subnet mask, gateway, DNS server, backup DNS server.
B. Dynamic IP
If the access mode is dynamic IP that the network provider gives, then you needs no setting,
click OK, Static IP is the common surfing mode of hotels.
C. PPPoE
If your surfing mode is “ADSL PPPOE” mode, just needs to input the account information
that the ISP provides you on the “User name” and “Password”, click OK.
D. Wireless relay
If you want to use Wireless relay mode, just choose “wan wifi modes”, click “scan all AP”, then
choose the wireless Ethernet port you want to relay, input password and click OK.
6.6 Basic setting of WiFi wireless network
Click the left menu, “Wireless network setting’ - “Basic setting”, you can have wireless network
settings of network mode, SSID, wireless channel and other basic settings.
7. Wireless network storage function: the iPad terminal devices how to visit U disk and
HDD?
It provides a USB port, U disk or HDD card reader to have connection, supports sharing and
visiting of the storage devices’ content in wireless way. Take ios platform as an example, can use
the third-party stream media software to play, upload, download the sharing files of the USB
storage, such as Goodplayer, OPlayerHD, TIOD and Aceplayer.
Step1: insert U disk, HDD and other USB storage devices into the USB port of the router.
Step2: open the switch of the router to check its blue LED status indicator light.
Step3: open the iPad’s WiFi setting, choose SSID of the 3G WiFi device to have wireless
network connection.
Step4: click Safari browser, input “http://192.168.169.1” or “wd” on the address bar, click Go,
then click Multimedia viewing icon, can enter the router’s mobile storage file browsing interface,
you can quickly visit the pictures, videos, music and other files in the U disk or the HDD.