Occupational Safety and Health Department
TRAINING INSTITUTE
EDUCATION CENTER
Home of the
2016 COURSE SCHEDULE
California
na
Arizo
Nevada
Hawaii
Highlights
n New San Diego Course Location
n Learn How to Become an Outreach Trainer
n Bring UCSD Safety Courses to Your Workplace
(800) 358-9206 • osha.ucsd.edu
Serving Arizona, California, Guam, Hawaii, Nevada, and the Pacific Territories
Course Locations
UCSD’s OSHA Training Institute Ed
Reno
Sacramento
Las Vegas
Henderson
Honolulu
Claremont
Los Angeles
Anaheim
San Diego
Phoenix
Tucson
TRAINING INSTITUTE
EDUCATION CENTER
Arizona
California
Phoenix/Tempe
Anaheim
Arizona Safety Education Center
201 East Southern Avenue, Ste 204
Tempe, AZ 85282-5178
Brookhurst Community Center
2271 W. Crescent Avenue
Anaheim, CA 92801
Tucson
Bakersfield
Arizona Dept. of Occupational
Safety & Health (ADOSH)
2675 East Broadway Boulevard
Tucson, AZ 85719
New Location coming Soon.
Visit osha.ucsd.edu/Bakersfield
for more information.
Enrollments are only processed at our San Diego locations, online at osha.ucsd.edu or by calling (800) 358-9206;
enrollments not available at any other locations. Please verify course locations in the catalog or online at osha.ucsd.edu.
B
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
ducation Center Host Site Locations
Claremont
(Los Angeles-Inland Empire)
San Diego (University City)
OSHA Training Institute
Education Center
UC San Diego Extension
6256 Greenwich Dr.
San Diego, CA 92122
Enrollments Accepted at This Location
Safety Center
109 S. Spring Street
Claremont, CA 91711
Los Angeles
Hawaii
Honolulu
Figueroa Courtyard
261 South Figueroa
Los Angeles, CA 90012
Los Angeles
UCLA School of Public Health
650 Charles E. Young Dr, S.
Los Angeles, CA 90095
Sacramento
Sacramento Regional Builders
Exchange
1331 T Street
Sacramento, CA 95811
San Diego
OSHA Training Institute
Education Center
UC San Diego Extension
404 Camino del Rio S., Ste 102
San Diego, CA 92108
Tel: (800) 358-9206 or (619) 260-3070
Enrollments Accepted at This Location
Construction Training Center
of the Pacific
94-487 Akoki Street
Waipahu, HI 96797
Nevada
Henderson
Nevada OSHA/SCATS
1301 N. Green Valley Pkwy,
Ste 200
Henderson, NV 89074
Las Vegas
Associated General Contractors
150 N. Durango Drive,
Ste 100
Las Vegas, NV 89145
Reno
AGC Nevada
5400 Mill Street
Reno, NV 89510
Enrollments are only processed at our San Diego locations, online at osha.ucsd.edu or by calling (800) 358-9206;
enrollments not available at any other locations. Please verify course locations in the catalog or online at osha.ucsd.edu.
(800) 358-9206 • osha.ucsd.edu
1
Course Locations
California (continued)
California (continued)
OSHA 5400 - Trainer Course in Occupational
Safety and Health Standards for the
Maritime Industry . . . . . . . . . . . . . . . . 15
OSHA 5402 - Maritime Industry
Trainer Update Course . . . . . . . . . . . . 15
OSHA 5600 - Disaster Site Worker Trainer
Course. . . . . . . . . . . . . . . . . . . . . . . . . 15
UCSD Safety Courses
TABLE OF CONTENTS
Course Locations. . . . . . . . . . . . . . . . B-1
General Information . . . . . . . . . . . . . . . 3
Outreach Trainer Info . . . . . . . . . . . . . . 4
Contract Courses. . . . . . . . . . . . . . . . . . 5
Certificate Programs. . . . . . . . . . . . . . 6-9
Cal/OSHA Safety Courses
OSHA 5029 - Cal/OSHA Update for
Construction Industry Outreach
Trainers. . . . . . . . . . . . . . . . . . . . . . . .
OSHA 5039 - Cal/OSHA Update
for General Industry Trainers. . . . . . . . . . .
OSHA 5109 - Cal/OSHA Standards
for the Construction Industry. . . . . . . . . . .
OSHA 5119 - Cal/OSHA Standards for
General Industry. . . . . . . . . . . . . . . . .
10
10
10
10
OTIEC Safety Courses
OSHA 2015 - Hazardous Materials . . . . . .
OSHA 2045 - Machinery and Machine
Guarding Standards . . . . . . . . . . . . . .
OSHA 2055 - Cranes in Construction. . . . .
OSHA 2225 - Respiratory Protection. . . . .
OSHA 2255 - Principles of Ergonomics . . .
OSHA 2264 - Permit-Required Confined
Space Entry. . . . . . . . . . . . . . . . . . . . .
OSHA 3015 - Excavation, Trenching
and Soil Mechanics. . . . . . . . . . . . . . .
OSHA 3095 - Electrical Standards
(Low Voltage - Federal). . . . . . . . . . . .
OSHA 3115 - Fall Protection . . . . . . . . . . .
2
OSHA 510 - Occupational Safety and
Health Standards for the
Construction Industry . . . . . . . . . . . . .
OSHA 511 - Occupational Safety and
Health Standards for General
Industry. . . . . . . . . . . . . . . . . . . . . . . .
OSHA 521 - OSHA Guide to Industrial
Hygiene. . . . . . . . . . . . . . . . . . . . . . . .
OSHA 5410 - Occupational Safety and
Health Standards for the Maritime
Industry. . . . . . . . . . . . . . . . . . . . . . . .
OSHA 5810 - Hazards Recognition and
Standards for On-Shore Oil and Gas
Exploration and Production. . . . . . . . .
OSHA 6000 - Collateral Duty Course for
Other Federal Employees. . . . . . . . . .
OSHA 7115 - Lockout/Tagout . . . . . . . . . .
OSHA 7205 - Health Hazard Awareness . .
OSHA 7405 - Fall Hazard Awareness
for the Construction Industry . . . . . . .
OSHA 7500 - Introduction to Safety and
Health Management. . . . . . . . . . . . . .
OSHA 7505 - Introduction to Incident
(Accident) Investigation . . . . . . . . . . .
OSHA 7845 - Recordkeeping
Rule Seminar. . . . . . . . . . . . . . . . . . . .
12
12
12
EM385-1-1 40 Hour Safety . . . . . . . . . . . .
Electrical High Voltage Standards
- Federal . . . . . . . . . . . . . . . . . . . . . . .
Electrical High Voltage Standards - State.
Electrical Low Voltage Standards - State. .
Electrical Safety Standards NFPA 70E - 2-Day. . . . . . . . . . . . . . . .
Fire and Life Safety . . . . . . . . . . . . . . . . . .
Laws and Regulations . . . . . . . . . . . . . . . .
Safety Inspection Techniques. . . . . . . . . . .
Scaffolding. . . . . . . . . . . . . . . . . . . . . . . . .
Trainer Course - Confined Space. . . . . . . .
Trainer Course - Fall Protection. . . . . . . . .
Trainer Course - Forklift Safety . . . . . . . . .
Trainer Course - Rigging Safety. . . . . . . . .
Trainer Course - Trenching. . . . . . . . . . . . .
16
16
16
16
16
16
17
17
17
17
17
17
17
17
Instructors. . . . . . . . . . . . . . . . . . . . . . 18
12
At-A-Glance (by Date). . . . . . . . . . . . . 19
13
13
13
13
At-A-Glance (by Location). . . . . . . . . . 24
Enrollment Form. . . . . . . . . . . . . . . . . 33
13
13
13
13
11
OTIEC Trainer Courses
11
11
11
11
11
11
11
12
OSHA 500 - Trainer Course in Occupational
Safety and Health Standards for the
Construction Industry . . . . . . . . . . . . . 14
OSHA 501 - Trainer Course in Occupational
Safety and Health Standards for General
Industry. . . . . . . . . . . . . . . . . . . . . . . . 14
OSHA 502 - Update for Construction
Industry Outreach Trainers . . . . . . . . . 15
OSHA 503 - Update for General
Industry Outreach Trainers . . . . . . . . . 15
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
Occupational Safety & Health Department
General Information
My Extension
If you need any assistance with this
process, call (858) 534-3400.
2016 Course Discounts
A 10% course discount is available to
several organizations’ members, state and
Federal employees. More information can
be found on osha.ucsd.edu.
Hotel Accommodations
Reduced room rates are often available
for students. Hotel information can be
found on our website osha.ucsd.edu.
On-site Training
All courses in this catalog, and many
others, can be customized and taught
at your work place. Please call (858)
534-9272 to schedule training at your
location. For groups of 10 or more, this
can often be a more cost effective
manner to deliver needed training.
Course Credit
• BRN Credit: The Bureau of
Registered Nurses offers BRN
credit. Reference UCSD Provider
Number 00058.
• ABIH Credit: The American Board
of Industrial Hygiene offers
Certification Maintenance (CM)
points for specific courses which
have been registered.
• BCSP Credit: The Board of
Certified Safety Professionals
offers Continuance of Certification
(COC) points.
All of the Occupational Health and Safety Department courses at UC San Diego
Extension, including the OSHA Training Institute Education Center courses, offer
several types of academic and industry credits. The following is the general key
for calculating credits:
Credit
type
Half day
course
One day
course
Two day
course
Three day
course
Four day
course
Five day
course
0.4
0.8
1.6
2.4
3.2
4.0
CEU
Academic credit
0.4
0.5
1.5
2.5
3.0
4.0
ABIH (CM points)
0.67
1.33
2.67
4.0
5.34
6.68
BCSP (COCs)
0.4
.8
1.6
2.4
3.2
4.0
Refund Policy
Enrollment
• Cancellations must be made at
least two weeks prior to the course
start date to be eligible for a refund.
• Transfer requests prior to two weeks
will be honored.
• Transfers within the two weeks
prior to the course start date will be
allowable one time only.
• Students who do not show up for class
and do not call will not be refunded
or transferred to another section.
Travel Disclaimer
All travel plans must accommodate the
published course end time.
You can enroll online or via mail, phone
or fax. Many courses have new Federal
OSHA pre-requisites. Please see individual course description prior to enrolling.
• Online enrollment, visit: osha.ucsd.edu
Click the “Enroll Now” button on
the course description page.
• Phone enrollment call: (800) 358-9206
• Fax enrollment form to: (619) 294-3861
• Mail enrollment form to:
OSHA Training Institute
UC San Diego Extension
404 Camino del Rio South, Suite 102
San Diego, CA 92108
UCSD Extension reserves the right to
cancel a class two weeks prior to the
start date. In the event of a cancelled
course, the student will be notified and
given the option to transfer to another
section or receive a full refund.
(800) 358-9206 • osha.ucsd.edu
3
General Information
Access Your Student Records
•Enroll in classes
•View and/or print your enrollment
receipts
•Update your personal contact
­information
•View your academic history
•Download official transcript form
•Review and print grades
•Request copies of course descriptions and tuition receipts
Log On: Three Easy Steps
1.Visit My Extension at myextension.
ucsd.edu (do not use www)
2.Enter your user name (email
address, not Social Security number)
3.Enter password. (If you do not
know your password, click on
“Forgot your password?” to create
a new one).
UC San Diego OTIEC’s Outreach Trainers
Outreach Trainer Info
UCSD OTIEC’s Outreach Department is committed to providing friendly, efficient and speedy service to our thousands of trainers. We have dedicated
Outreach staff members, a robust and always improving online reporting tool and are available to answer questions via phone and email.
Outreach comments and questions should be directed to dedicated staff members at oti-outreach@ucsd.edu and/or 858-534-9283.
We are diligently working towards making UCSD the premier OTIEC for Outreach trainers to maintain their affiliation and card processing.
We value your opinions and appreciate the continual feedback regarding our new online system. Thank you for your continued support of our safety
and outreach programs.
Outreach Trainers
Be an OSHA-Authorized
Outreach Trainer!
Outreach Reporting Tool
To become a UCSD OSHA-authorized outreach trainer or to
maintain your trainer status for Construction, General Industry,
Maritime, Disaster Site or Cal/OSHA, follow these easy steps:
The UC San Diego OSHA Training Institute Education Center
developed a web based online Submission Tool for our
Outreach Trainers.
Step 1: Download the Prerequisite Verification of Eligibility Form by
clicking on “Apply Now” on the relevant trainer course page (500,
501, 502, 503, 5400, 5600, 5029, and 5039). You may also email
oshatraining@ucsd.edu for an electronic copy. Fill out the required
information on the form.
This advanced system allows for trainers to submit course
documentation electronically and receive cards in a timely and
efficient manner, avoiding any unnecessary delays. Often times,
card processing takes 24-72 hours—not the customary 30 days.
Step 2: Email the completed form along with a copy of your trainer
card or course completion certificate to oshatraining@ucsd.edu. Please
note that your verification form cannot be processed without proper
proof of the required prerequisites.
Step 3: Once you have received an approval email from the OH&S
department, you will then follow the instructions to enroll in the class
of your choice.
Additionally, our system provides a database for trainers to
access all student and card information in real time significantly
cutting down time to find student records and process
replacement cards when needed.
We strive to be the gold standard in Outreach and continue to
partner with our trainers to ensure that they are equipped with
all the necessary tools to make them successful.
Visit osha.ucsd.edu/outreach
UC San Diego Safety Trainer Newsletter
UC S D
This newsletter has been designed for the UCSD OTIEC Outreach Trainers. It provides News, Resources,
Tools and Updates related to construction, general industry, maritime, Cal/OSHA, disaster site and international
training. Don’t miss out, sign up now!
Visit osha.ucsd.edu/newsletter for more information.
4
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
ONSITE SAFETY TRAINING
Utility, Government and
Business Customers
As today’s businesses are faced
with changing technologies,
stricter regulations, and increasing demands on their time, today’s
safety professionals need training
resources to protect the bottom
line with proven training results.
Customized
Training Programs
Our expert instructors specialize
in designing customized training
programs tailored to meet your
unique business needs that ensure
cost-effective solutions and enable
sustainable business practices. Our
courses are aligned with your mission, values and strategic goals.
International Operations
Exceptional Customer Service
With the universal global economy,
businesses with overseas operations must prove their commitment
to safety training and ensure a
healthy workplace environment
for their employees and customers.
Our curriculum helps your organization to identify and avoid preventable business impacts.
UCSD’s OSHA Training Institute
Education Center is committed
to developing lasting relationships with each client by providing
superior customer service based on
quality, integrity and trust.
To obtain pricing on contracts,
please call (800) 534-9272 and ask
for a contract specialist or email
oshatraining@ucsd.edu.
Contract Only Courses
All of the courses offered at the UC San Diego Extension Occupational Safety and Health Department and
UCSD OSHA Training Institute Education Center can be brought to your site. In addition, there are many
awareness courses that are specifically designed for onsite training. These can be scheduled together to
make a customized “Workshop Week” for your employees.
Contract Courses
• OSHA 7000 – Training Guidelines for Safe Patient Handling
• OSHA 7100 – Introduction to Machinery and Machine Safeguarding
• OSHA 7105 – Evacuation and Emergency Planning
• OSHA 7120 – Introduction to Combustible Dust Hazards
• OSHA 7125 – Seminar on Combustible Dust Hazards
• OSHA 7200 – Bloodborne Pathogens Exposure Control
for Healthcare Facilities
• OSHA 7210 – Pandemic Influenza Preparedness
• OSHA 7225 – Transitioning to Safer Chemicals (Coming Soon)
• OSHA 7300 – Understanding OSHA’s Permit Required
Confined Space Standard
• OSHA 7400 – Noise Hazards in the Construction Industry
• OSHA 7410 – Managing Excavation Hazards
• OSHA 7415 – Construction Industry Hazards and Prevention Strategies
• OSHA 7510 – Introduction to OSHA/or Small Businesses
TRAINING INSTITUTE
EDUCATION CENTER
(800) 358-9206 • osha.ucsd.edu
5
Certificate Programs
UC San Diego Occupational Safety and
CERTIFICATE PROGRAM BENEFITS
Regardless of your educational background, UCSD Certificate Programs provide both experienced and newer
safety professionals important workplace knowledge and practical experience regarding safety and safety
standards. Benefits include:
• Practical application of OSHA regulations in
your workplace
• Networking with other professionals
• Access to the most current information
• Justification for advancement or promotion
• Opportunities for new jobs or careers
VA BENEFITS
Eligible students may utilize their VA educational benefits for the approved Professional Certificate in
Occupational Safety and Health and the Safety Specialist certificate program. Veterans, veteran dependents,
and others eligible for veterans’ education programs should determine their benefits and obtain authorization with the Department of VA prior to enrolling in courses.
Veterans are encouraged to contact unex-veterans@ucsd.edu with any additional questions.
CERTIFICATE PROGRAM FINANCIAL ASSISTANCE
UC San Diego Extension’s Occupational Safety and Health Department is pleased to provide information
regarding financing your continuing education needs. Paying for a certificate program should not be an
obstacle in furthering your education. Private Student loans are available to assist students with the cost of
enrollment fees, certificate fees, and required textbooks. For more information on loans and other financial
resources available (including San Diego Workforce Partnership funds), please visit extension.ucsd.edu/financial.
CERTIFICATES AT A GLANCE
The Safety
Leader
(5+ years exp.)
Professional Certificate
in Occupational Safety
and Health
✔
Safety
Specialist
Certificate
Public Sector Safety &
Health Fundamentals
Certificate Program
6
The Safety
The Safety
Internship &
Student
Rookie
Leadership
(1-5 years exp.) (0-1 years exp.) Skills
✔
✔
✔
✔
✔
UC San Diego Extension
Construction
Track
General
Industry Track
✔
✔
✔
✔
✔
(800) 358-9206 • osha.ucsd.edu
PROFESSIONAL CERTIFICATE IN OCCUPATIONAL SAFETY AND HEALTH
This Professional Certificate provides both experienced and newer safety professionals important workplace knowledge and practical experience regarding safety and safety standards. This program offers concentrated study in areas
directly applicable to many jobs and can add breadth and depth to existing knowledge and skills.
This program requires the completion of either the OSHA 500 – Trainer Course in OS&H Standards for the
Construction Industry or OSHA 501 – Trainer Course in OS&H Standards for General Industry. The required prerequisite to these courses are the OSHA 510 – OS&H Standards for the Construction Industry or OSHA 511 – OS&H
Standards for General Industry. In addition to the required course, students must have a minimum of
5 years in occupational health and safety job experience (within either construction or general industry).
The recommended beginning courses are the OSHA 510 or OSHA 511.
Students have five years to complete the required courses from the date of their certificate registration.
• Target Audience: Individuals with 5+ years of
experience in occupational safety and health.
This applies to both the Public and Private Sectors.
• Location of Courses: Courses in the program are
offered throughout all UCSD OTIEC locations
• Certificate Design: This is a University of California,
San Diego program
• Required Courses: a minimum of 7 courses
are required
• Total Units: 24 units are required to complete
the certificate, 35 units for the dual certificate
THE PROFESSIONAL CERTIFICATE IS AVAILABLE IN CONSTRUCTION,
GENERAL INDUSTRY OR A DUAL AREA OF SPECIALIZATION.
Required for the General Industry Track
Required for the Construction Track
Course Title
Units
Course Title
Units
OSHA 3095 Electrical Low Voltage Standards - Federal
OSHA 3115 Fall Protection
OSHA 521 Industrial Hygiene
OSHA 510 OSHA Standards for the Construction Industry
UCSD 3200 Scaffolding
OSHA 500 Trainer Course for the Construction Industry
OSHA 3015 Trenching & Excavation
Electives
3.0
3.0
3.0
3.0
2.5
3.0
2.5
4.0
OSHA 3095 Electrical Low Voltage Standards - Federal
OSHA 2255 Principles of Ergonomics
OSHA 521 Industrial Hygiene
OSHA 2045 Machine Guarding
OSHA 511 OSHA Standards for General Industry
OSHA 2225 Respiratory Protection
OSHA 501 Trainer Course for General Industry
Electives
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
(TOTAL REQUIRED CREDITS) 24.0
(TOTAL REQUIRED CREDITS) 24.0
Dual Certificate
A dual certificate in both Construction and General Industry is earned by taking all required courses in both tracks. Thirty-five (35) units total with no
additional electives required. Students enrolled in the dual certificate are only required to take one of the two trainer courses, OSHA 500 or OSHA
501. If students choose not to take the other Trainer Course, they must instead take 3 other units as electives to reach the required 35 units in the Dual
Certificate. Elective units must be chosen from the UCSD OSHA Training Institute Education Center catalog from courses taken for credit.
How to enroll
1.Visit osha.ucsd.edu
2.On the “Professional Certificate in Occupational Safety and
Health” page, click on “Apply Now”
3.Login to your “My Extension” account (or follow the
prompts to create a new one)
4.Once logged in, follow the instructions and pay the $60 certificate fee to complete the process. There is no application fee.
(800) 358-9206 • osha.ucsd.edu
7
Certificate Programs
Health Department Certificate Programs
Certificate Programs
UC San Diego Occupational Safety and
SAFETY SPECIALIST CERTIFICATE
According to recent data, the number of occupational safety and health jobs will outpace the number of trained professionals to fill them. This shortage requires employees skilled in a variety of
safety topics.
The Safety Specialist Certificate was designed by UC San Diego Extension and the Associated Builders and
Contractors (ABC) San Diego Chapter and is an intensive, cohort-based program that combines in-class education with associated skills practice. Included in the certificate program topics are all items necessary for individuals to prepare for entry-level safety jobs in the construction industry, including an on-the-job internship.
Specific careers program graduates will be competitive for include:
• Field Safety Supervisor • Safety Officer
• Safety Specialist • Occupational Health and Safety Specialists
• Safety Coordinator
• Target Audience: Individuals with 0-5 years of experience in occupational safety and health. This applies
to both the Public and Private Sectors.
• Location of Courses: Modules/classes in the program
are located at UC San Diego Extension’s University
City Center
• Certificate Design: This is a University of California,
San Diego program
• Required Courses: all of the six intensive modules
are required
• Total Units: 31 units are required to complete the
certificate
Certificate Course Matrix
About the Job Internship
Required Certificate Courses (Must be taken as a cohort; no individual enrollments)
Course Title
Units
Module 1 Introduction to Safety 8
Module 2 Regulation Fundamentals for Safety 7
Module 3 Safety Practices 12
Module 4 U.S. Army Corp of Engineers Safety and Health 4
Module 5 Job Internship 0
Module 6 Intensive Leadership Training 0
How to Enroll
1.Visit osha.ucsd.edu
2.On the “Safety Specialist Certificate” page, click on “Apply Now”
3.Login to your “My Extension” account (or follow the prompts to create
a new one)
4.Complete the application in its entirety
5.This program requires an application review by the Advisory Committee.
You will be contacted about your application and will not automatically
be enrolled in the program.
8
UC San Diego Extension
The on-the-job portion of the Safety
Specialist Certificate Program, Module 5
consists of a 3-week (120 hours) internship
and a workplace project providing students
the opportunity to apply their newfound
knowledge and skills in a variety of realworld settings within an existing and fully
operational local company.
Workplace Internship students will be
matched with an experienced safety professional to help guide and achieve goals that
draw on core construction, safety, health,
environmental and business skills.
Students will operate under company supervision and deliver project activities requiring
varied safety, health, and environmental
knowledge as well as interpersonal skills.
Responsibilities may include site reviews,
identifying health concerns, Hazard Analysis
and worker training activities.
(800) 358-9206 • osha.ucsd.edu
PUBLIC SECTOR SAFETY & HEALTH FUNDAMENTALS CERTIFICATE PROGRAM
The certificate program in Public Sector Safety & Health Fundamentals supports OSHA’s mission by training public sector employees in occupational safety and health to reduce incident rates for workers in state
and local governments (the certificate program is highly applicable to private industry workers as well). Participants
have the opportunity to earn certificates for Construction and General Industry training.
Participants must complete a minimum of seven OTI Education Center courses (minimum of 68 contact hours) to
earn the certificate in either Construction or General Industry.
• Target Audience: Those new to safety in both the
Public and Private Sectors
• Location of Courses: Courses in the program are
offered throughout all UCSD OTIEC locations
• Certificate Design: This certificate supports OSHA’s
mission to reduce incident rates for workers
• Required Courses: a minimum of 3 total courses are
required per specialization
• Total Hours: a minimum of 68 instruction hours are
required to complete each program specialization
(construction or general industry).
General Industry
Required Certificate Courses
Course Title
Construction
Required Certificate Courses
Course Title
Min. Contact Hours
OSHA 510 Occupational Safety and Health Standards
for Construction
OSHA 7500 Introduction to Safety and Health Management
OSHA 7505 Introduction to Accident Investigation
26
5.5
7.5
(TOTAL HOURS) 39.0
Elective Courses for Construction Industry
Course Title
OSHA 7410 Managing Excavation Hazards
OR
OSHA 3015 Excavation, Trenching and Soil Mechanics
OSHA 3095 Electrical Standards
OSHA 7405 Fall Hazard Awareness for the
Construction Industry
OR
OSHA 3115 Fall Protection
OSHA 7105 Evacuation and Emergency Planning
OSHA 7110 Safe Bolting: Principles and Practices
OSHA 7205 Health Hazard Awareness
OSHA 7400 Noise in the Construction Industry
OSHA 7845 Recordkeeping Rule Seminar
Min. Contact Hours
OSHA 511 Occupational Safety and Health Standards
for General Industry
OSHA 7500 Introduction to Safety and Health Management
OSHA 7505 Introduction to Accident Investigation
Min. Contact Hours
6.5
20
26
5
18
4
7
6
5.5
4
26
5.5
7.5
(TOTAL HOURS) 39.0
Elective Courses for General Industry
Course Title
Min. Contact Hours
OSHA 3095 Electrical Standards
26
OSHA 7300 OSHA’s Permit-Required Confined
Space Entry
7
OR
OSHA 2264 Permit-Required Confined Space Standard
20
OSHA 7000 OSHA Training Guidelines for Safe
Patient Handling
7.5
OSHA 7005 Public Warehousing and Storage
7
OSHA 7100 Introduction to Machinery and Machine
Safeguarding
4
OR
OSHA 2045 Machinery & Machine Guarding Standards
26
OSHA 7105 Evacuation and Emergency Planning
4
OSHA 7115 Lockout/Tagout
7.5
OSHA 7200 Bloodborne Pathogens Exposure Control
for Healthcare Facilities
7
OSHA 7205 Health Hazard Awareness
6
OSHA 7210 Pandemic Influenza Preparedness
5.5
OSHA 7845 Recordkeeping Rule Seminar
4
How to enroll
1.Review the certificate requirements to determine the appropriate program (construction or general industry)
2.Find and register for courses at osha.ucsd.edu
3.Upon completion of all courses, submit completed application to oshatraining@ucsd.edu (application available on “Public Sector Safety &
Health Fundamentals Certificate Program” page or by emailing oshatraining@ucsd.edu)
4.Submit the $90 fee to receive your certificate
(800) 358-9206 • osha.ucsd.edu
9
Certificate Programs
Health Department Certificate Programs
Cal/OSHA Courses
Cal/OSHA Safety Courses
OSHA 5029 - Cal/OSHA Update
for Construction Industry
Outreach Trainers
This one day course updates the OSHA 5109
with new and current Cal/OSHA standards
and continues the student’s authorization to
teach both 10 and 30 hour Cal/OSHA Outreach
Program.
Note: Required prerequisite: OSHA 5109 or
OSHA 5029 within four years. IMPORTANT—
ONLINE ENROLLMENT IS NOT PERMITTED. A
Verification of Prerequisite Form must be sent
in prior to enrollment, along with proof of
your trainer status. Acceptable forms of proof
are: a copy of your OSHA 500/OSHA 502 trainer
card with Cal/OSHA sticker or Certificates of
completion. The Cal/OSHA Partnership authorized Outreach Trainers must bring their Federal
Outreach Trainer card in order to obtain a “Cal/
OSHA Partnership Trainer sticker”. To obtain
the Verification of Prerequisite Form please
click on “Apply Now” next to a class below.
Cal/OSHA Sticker Expiration: These stickers
expire on the same date as the Outreach Trainer
card to which they are affixed. For additional
information, review the Cal/OSHA Partnership
Program Description.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 4
Feb 19
Apr 28
May 12
Aug 25
Location Los Angeles San Diego Claremont Sacramento San Diego Section ID
112124
110903
111937
111947
110992
OSHA 5039 - Cal/OSHA Update
for General Industry Trainers
This one day course updates the OSHA 5119
with new and current Cal/OSHA standards
and continues the student’s authorization to
teach both 10 and 30 hour Cal/OSHA Outreach
Program.
Note: Required prerequisite: OSHA 5119 or
OSHA 5039 within four years. IMPORTANT—
ONLINE ENROLLMENT IS NOT PERMITTED. A
Verification of Prerequisite Form must be sent
in prior to enrollment, along with proof of
your trainer status. Acceptable forms of proof
are: a copy of your OSHA 501/OSHA 503 trainer
card with Cal/OSHA sticker or Certificates of
completion.The Cal/OSHA Partnership authorized Outreach Trainers must bring their Federal
Outreach Trainer card in order to obtain a “Cal/
OSHA Partnership Trainer sticker”. To obtain
the Verification of Prerequisite Form please
click on “Apply Now” next to a class below.
Cal/OSHA Sticker Expiration: These stickers
expire on the same date as the Outreach Trainer
card to which they are affixed. For additional
information, review the Cal/OSHA Partnership
Program Description.
Dates
Feb 4
Feb 25
Mar 4
May 19
Nov 3
Section ID
111913
112127
111081
111951
111061
OSHA 5109 - Cal/OSHA Standards
for the Construction Industry
Developed in partnership with Cal/OSHA, this
4-day course emphasizes Title 8 Construction
Industry standards and compliance. Topics
include IIPP, Ergo, Electrical and many others.
The course also provides existing Fed OSHA
trainers an endorsement authorizing them to
teach 10 & 30 hr Federal- Cal/OSHA outreach
courses. Resources and Cal/OSHA training guidelines will be covered.
Note: Important—Students taking this course
who want to receive the Cal/OSHA Outreach
Trainer designation must meet the following
required prerequisites: OSHA 500 or 502 (must
be a current trainer), One year of Cal/OSHA
general industry safety experience, OSHA 500
card must be brought to class. The Cal/OSHA
Partnership authorized Outreach Trainers will
have their Federal Outreach Trainer cards
affixed with a “Cal/OSHA Partnership Trainer
sticker.” Cal/OSHA Sticker Expiration: These
stickers expire on the same date as the Outreach
Trainer card to which they are affixed. For
additional information, review the Cal/OSHA
Partnership Program Description.
Note: Important—Students taking this course
who want to receive the Cal/OSHA Outreach
Trainer designation must meet the following
required prerequisites: OSHA 501 or 503 (must
be a current trainer), One year of Cal/OSHA
general industry safety experience, OSHA 501
card must be brought to classThe Cal/OSHA
Partnership authorized Outreach Trainers will
have their Federal Outreach Trainer cards
affixed with a “Cal/OSHA Partnership Trainer
sticker.” Cal/OSHA Sticker Expiration: These
stickers expire on the same date as the Outreach
Trainer card to which they are affixed. For
additional information, review the Cal/OSHA
Partnership Program Description.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jan 25-28
Apr 25-28
May 23-26
Jun 20-23
Aug 1-4
Nov 7-10
Nov 14-17
Location Claremont San Diego Los Angeles Bakersfield
San Diego Sacramento
Anaheim Section ID
111911
110946
112134
112263
110983
111983
112153
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 29-Mar 3
Apr 4-7
Apr 25-28
Jun 6-9
Aug 15-18
Sep 19-22
Location
San Diego Sacramento Los Angeles Claremont San Diego Bakersfield
Section ID
110906
111931
112133
111954
110988
111975
OSHA 5119 - Cal/OSHA Standards
for General Industry
Developed in partnership with Cal/OSHA, this
4-day course emphasizes Title 8 General Industry
standards and compliance. Topics include IIPP,
Ergo, Electrical and many others. The course
also provides existing Fed OSHA trainers an
endorsement authorizing them to teach 10 &
30 hr Cal/OSHA outreach courses. Resources and
Cal/OSHA training guidelines will be covered.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
10
Location
Sacramento
Los Angeles
San Diego
Claremont
San Diego
UC San Diego Extension
UCSD OTIEC, Cuyamaca College, and
Columbia Southern University have
formed an exciting learning partnership
paving the way to Degree Completion!
Students may apply UCSD OSHA Education
Center courses towards an Associate’s Degree
at Cuyamaca College and/or an Associate’s
and Bachelor’s Degree at Columbia Southern
University. Cuyamaca College courses may be
applied to a Bachelor’s and Associate’s Degree at
Columbia Southern University, as well as Columbia
Southern University courses may be applied to an
Associate’s Degree at Cuyamaca College.
For additional information
go to osha.ucsd.edu
(800) 358-9206 • osha.ucsd.edu
OTIEC Safety Courses
OSHA 2015 - Hazardous Materials
Learn how to apply OSHA general industry standards and integrate materials from other safety
standards that relate to hazardous materials.
Related processes such as spraying and dipping
are covered, as well as electrical equipment.
Topics include: Flammable Liquids, Hazardous
Waste Operations, Confined Space, Compressed
Gases, Hazardous Locations.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jun 6-9
Jun 27-30
Sep 19-22 Oct 31-Nov 3
Location San Diego Tempe
San Diego Los Angeles
Section ID
110958
112227
111036
113261
OSHA 2045 - Machinery and
Machine Guarding Standards
Get a comprehensive picture of common machinery and related safety standards. Learn aspects
of machine inspection and hazard abatement.
A mock inspection of a local plant provides
hands-on experience. Topics Include: Point of
Operation, Portable Hand and Powered Tools,
Power Presses, Press Brakes, and Lockout/Tagout.
Note: Requires appropriate clothing for field
exercise.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Location Tempe San Diego Claremont
Tempe
San Diego Section ID
111309
110910
111959
111380
111052
OSHA 2055 - Cranes in
Construction
This course covers the best practices in crane
and derrick operation using the OSHA Cranes
and Derricks in Construction Rule as a guide.
Course topics include hazards associated with
crane assembly and disassembly, types of cranes,
lifting concepts, rigging and wire rope, signaling, employee qualifications and training, and
maintenance, repair, and inspection requirements. Students will participate in workshops
to reinforce concepts of safe crane operation.
Upon course completion students will have the
ability to identify the types of cranes and their
components and attachments, determine safe
operating conditions, and recognize common
violations of OSHA Standards.
Note: Requires appropriate clothing for field
exercise.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jan 25-28
Aug 29-Sep 1
Location Tempe San Diego Section ID
111295
110995
Learn how to establish, maintain, and monitor a
respirator program following the requirements
in 29 CFR 1910.134. Discuss the technical aspects
for the proper selection and use of respiratory
protection. Evaluate compliance with OSHA’s
standard by using the compliance directive and
the “Small Entity Compliance Guide.” Topics
include: Respiratory Protection Program, Fit
Testing Demonstration, Selection of Respirators,
Maintenance and Care.
Note: It is highly recommended to complete the
OSHA 521 course prior to this course.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jan 25-28
Apr 18-21 Jul 11-14
Jul 25-28
Aug 15-18
Oct 31-Nov 3 Location San Diego Tempe Los Angeles San Diego Waipahu San Diego Section ID
110878
111324
112137
110979
112141
111060
OSHA 2255 - Principles of
Ergonomics
(formerly known as “OSHA 2250”)
Get the information you need to combat musculoskeletal injuries. Course highlights include
industrial case studies covering analysis and
design of work stations and equipment, laboratory sessions in manual lifting and coverage of OSHA’s proposed ergonomic protection
standard. Topics Include: Repetitive Injuries,
Musculoskeletal Disorders, Video Displays,
Workstation and Tool Design, and Seating.
Note: Requires appropriate clothing for field
exercise.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Mar 7-10
Apr 11-14
Aug 1-4
Aug 22-25
Nov 28-Dec 1 Location Tempe San Diego San Diego Los Angeles San Diego
Section ID
111317
110943
110981
112142
111071
OSHA 2264 - Permit-Required
Confined Space Entry
The danger of explosion, poisoning, and asphyxiation exists every time a worker enters a confined
space. Learn the OSHA required confined space
entry standard, hazards associated with entry
procedures, Personal Protective Equipment, ventilation and purging requirements, calculations
and techniques, and appropriate atmosphere
testing equipment. Course features hands-on
training with explosion meters, oxygen meters,
and other test equipment.
Dates
Apr 11-13
Apr 25-27
May 23-25 Oct 24-26 Location Anaheim San Diego Tempe San Diego Section ID
112132
110945
111328
111054
OSHA 3015 - Excavation,
Trenching and Soil Mechanics
(formerly known as “OSHA 3010”)
Construction trenching accidents claim the lives
of 40 workers per year. Save lives by learning
the OSHA standards and the safety aspects of
excavation and trenching. Discover practical
soil mechanics and its relationship to the stability of shored and unshored slopes and walls
of excavations. Topics Include: Principles and
Applications, Sloping, Benching, and Shoring.
Note: Requires appropriate clothing for field
exercise.
Fee: $675
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 1-3
Jun 27-29
Jul 25-27
Aug 29-31
Sep 26-28
Oct 10-12 Nov 7-9
Dec 5-7 Location San Diego Tempe
Claremont
San Diego Los Angeles
Tempe
San Diego Waipahu Section ID
110879
111376
111962
110993
112422
111392
111062
112155
OSHA 3095 - Electrical Standards
(Low Voltage - Federal)
Learn OSHA’s standards associated with electrical installations and equipment. Gain knowledge of single and three phase systems, cord and
plug connected and fixed equipment, grounding, ground fault circuit interrupters, hazardous
locations and safety related work practices.
Special emphasis is placed on electrical hazard
recognition and OSHA inspection procedures.
Topics include: Personal Protective Equipment,
Energized Parts, Grounding, Medical Services /
First Aid, Hazardous Energy Control.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Location Section ID
Mar 14-17
San Diego 110912
Apr 25-28
Tempe 112228
Jun 20-23 San Diego 110962
Sep 26-29 San Diego 111049
Nov 7-10Tempe111396
Nov 14-17 Las Vegas
111985
Nov 28-Dec 1 Claremont
111987
Fee: $675
Time: 8:00 a.m.-4:30 p.m.
(800) 358-9206 • osha.ucsd.edu
11
OTIEC Safety Courses
Dates
Feb 16-19
Mar 7-10
Jul 11-14 Jul 25-28
Oct 3-6
OSHA 2225 - Respiratory
Protection
OSHA 3115 - Fall Protection
(formerly known as “OSHA 3110”)
This 4-day course includes: encounter stateof-the-art technology for fall protection and
current OSHA requirements. Topics include the
principles of fall protection, the components of
fall arrest systems, the limitations of fall arrest
equipment, and OSHA policies regarding fall
protections. Course features a one-day field
exercise demonstrating fall protection equipment. Topics include: Conventional Systems,
Body Holding Devices, Anchor Points, Harness,
Vertical / Horizontal Traveling Systems.
Note: Requires appropriate clothing for field
exercise.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jan 19-22
May 2-5
Aug 15-18
Sep 26-29
Oct 24-26
Nov 7-10
Dec 5-8 Location Tempe
San Diego San Diego
Tempe
Claremont
Waipahu San Diego Section ID
111289
110949
110989
111390
111980
112150
111075
OTIEC Safety Courses
OSHA 510 - Occupational Safety
and Health Standards for the
Construction Industry
According to the Bureau of Labor Statistics,
construction was the leading industry for injuries. Learn the 29 CFR 1926 standards, as well as
construction safety and health principles to help
prevent injury. Special emphasis is placed on
those areas that are the most hazardous, using
OSHA standards as a guide. Topics Include: OSH
Act, Safety Programs, Fall Protection, Personal
Protective Equipment, Stairs and Ladders.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Safety Matters Sign-Up
Don’t miss out on insights about
current events from our instructors,
exclusive offers and new courses from
UC San Diego’s OSHA Training Institute
Education Center. Visit osha.ucsd.edu
to sign up.
Dates
Jan 11-14
Jan 11-14
Jan 19-22
Jan 25-28
Jan 25-28
Feb 8-11 Feb 16-19
Feb 22-25 Mar 7-10
Apr 4-7 Apr 11-14 May 2-5 Jul 11-14 Jul 18-21 Jul 18-21 Aug 1-4
Aug 8-11 Aug 15-18
Sep 19-22 Oct 3-6 Oct 24-27 Nov 14-17 Location San Diego Tempe
Bakersfield Anaheim Waipahu Claremont Sacramento Henderson Tucson San Diego Tempe
Reno San Diego Tempe
Bakersfield
Las Vegas
Claremont
Sacramento
San Diego Tempe
Reno
San Diego OSHA 521 - OSHA Guide to
Industrial Hygiene
Section ID
110874
111285
111910
112117
112116
111915
111916
111918
111921
110939
111323
111939
110968
111379
111961
111964
111965
111967
111035
111391
111981
111065
According to the Archives of Internal Medicine
(AIM), more than 60,300 fatalities result from
occupational illnesses annually. Minimize the
threat of illnesses by learning industrial hygiene
practices and related OSHA regulations and
procedures. Learn how to recognize potential
health hazards in the workplace and define
terms relating to OSHA health requirements.
From workshops in health hazard recognition to
air contaminant sampling, this course will give
you the information you need to combat occupational illnesses. Topics include: Respiratory
Protection, Hazard Communication, Confined
Spaces, Ventilation, and Recordkeeping.
Note recommended prerequisite course: OSHA
510, OSHA 511, OSHA 5109 or OSHA 5119.
Requires appropriate clothing for field exercise.
It is also highly recommended to bring a calculator to class.
OSHA 511 - Occupational Safety
and Health Standards for General
Industry
For students wanting to learn the 29 CFR 1910
standards, this course is a must. Learn crucial
OSHA policies, procedures, and standards, as
well as general industry safety and health principles as they relate to real world situations.
Special emphasis is placed on those areas that
are the most hazardous, using OSHA standards
as a guide. Topics Include: OSH Act, Safety
and Health Management Systems, Personal
Protective Equipment, Hazard Communication,
and Electrical.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jan 11-14 Feb 8-11
Mar 21-24
Apr 18-21 May 2-5 May 2-5 May 16-19
Jun 13-16
Jun 20-23
Jun 27-30
Jul 18-21
Jul 25-28
Aug 1-4
Aug 8-11
Sep 12-15
Sep 19-22
Oct 10-13
Oct 24-27
Nov 14-17
Location San Diego Tempe Claremont Las Vegas Bakersfield San Diego Tempe Tucson Waipahu Sacramento
Los Angeles San Diego Tempe
Reno
Claremont
Anaheim Bakersfield
San Diego Tempe
Section ID
110875
111316
111926
111934
111940
110948
111327
111956
112136
111958
112138
110969
111381
111966
111973
112144
111979
111055
111397
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 29-Mar 3
Mar 21-24
Apr 4-7
Aug 8-11
Nov 7-10
Location San Diego Los Angeles Tempe San Diego San Diego Section ID
110907
112130
111322
110985
111063
OSHA 5410 - Occupational Safety
and Health Standards for the
Maritime Industry
This course is the standards for the Maritime
Industry. It is also a required Prerequisite for the
OSHA 5400 - Trainer Course - Maritime Safety.
Given OSHA standards and current industry
information, students will be able to demonstrate ability to interpret federal standards for
the maritime industry. Students will be able to
identify the jurisdictional responsibilities of federal regulatory agencies in maritime industries,
andable to identify how the hierarchy of rules
applies to maritime industries covered by OSHA,
Inspections, Citations, and Enforcement Policies.
Fee: $925
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 8-12
May 16-20
Oct 24-28
Location San Diego San Diego San Diego Section ID
110899
110955
111056
Course Credit Calculations
UCSD safety and UCSD OTIEC courses offer
several types of academic and industry credit.
See page 3
12
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
OSHA 5810 - Hazards Recognition
and Standards for On-Shore
Oil and Gas Exploration and
Production
This course provides essential information for
employees and employers to protect themselves
by developing the knowledge and skills to anticipate, recognize, evaluate and control hazards
common to the on-shore oil and gas exploration
and production industry. This includes work
sites associated with the on-shore exploration
and production oil and gas industry including,
but not limited to construction, drilling, completion, well servicing, production, product gathering and processing, and product transmission.
This course is intended for employees and
employers engaged in all phases of on-shore oil
and gas exploration and production.
Fee: $925
Time: 8:00 a.m.-4:30 p.m.
Dates
Apr 11-15
Location Bakersfield Section ID
111933
OSHA 6000 - Collateral Duty
Course for Other Federal
Employees
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Mar 14-17
Nov 14-17
Nov 28-Dec 1
Location San Diego San Diego Tempe
Section ID
110911
111068
111398
OSHA 7115 - Lockout/Tagout
In this course, students will learn about the role
and responsibility of the employer to develop
and implement an energy control program, or
lock-out/tag-out (LOTO) for the protection of
workers while performing servicing and maintenance activities on machines and equipment.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
Dates
Apr 11
Location San Diego OSHA 7505 - Introduction to
Incident (Accident) Investigation
This one-day course focuses on recognizing
potential health hazards in the workplace, and
avoiding, minimizing, controlling or eliminating
them whenever possible. Exposure to health
hazards continues to be common in spite of
advances in control measures and techniques.
This course will provide information on health
hazards and discuss ways to recognize, evaluate,
and control them in the workplace.
This course will provide the knowledge, practical skills, and tools to conduct accident and
incident investigations. Topics in this interactive
course will include needs and responsibilities
for investigation, preparation and planning,
witness interviewing and qualifying, photographing and diagramming of accident scenes,
analytical techniques, report writing, and legal
aspects. Human and environmental factors and
their interaction with the investigation will also
be covered in this two-day course packed with
information.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
Dates
Jun 20
Location Tempe Section ID
111332
OSHA 7405 - Fall Hazard
Awareness for the Construction
Industry
In 2004, the Bureau of Labor Statistics data
showed that 36 percent of the 1,224 construction worker fatalities were attributed to falls.
Designed for small construction employers and
employees, this course is packed with information on fall hazards at work sites. Providing
a focus on falls to a lower level rather than
falls from slips and trips, Fall Arrest Awareness
teaches you how to control or prevent these
hazards whenever possible. Topics Include:
Identification of Fall Hazards, Analyzing Fall
Hazards, Preventing Fall Hazards, and OSHA
Resources.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
Dates
Jun 22
Location Tempe Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 11-12
May 9-10
Oct 31-Nov 1
Dec 1-2
Location San Diego Tempe Tucson
San Diego Section ID
110900
111907
111982
111073
OSHA 7845 - Recordkeeping Rule
Seminar
This half-day course will assist employers in
identifying and fulfilling their responsibilities
for posting certain records, maintaining records
of illnesses and injuries, and reporting specific
cases to OSHA. Several practice workshops are
included. Employees of companies that have
responsibilities under OSHA’s revised recordkeeping Rule 29 CFR 1904 will benefit from this
course.
Fee: $125
Time: 8:00 a.m.-12:00 p.m.
Section ID
111334
OSHA 7500 - Introduction to
Safety and Health Management
Dates
Apr 13
Jun 23
Location San Diego Tempe Section ID
110942
111335
OTIEC Safety Courses
If you are a federal employee, learn to recognize basic safety and health hazards in the
workplace and effectively assist agency safety
and health officers in their inspection and
abatement efforts. This course introduces federal agency collateral duty safety and health
personnel to the OSH Act, Executive Order
12196, 29 CFR 1960, and 29 CFR 1910. A mock
inspection of a government facility will provide
hands on experience. Topics include Walking
and Working Surfaces, Industrial Hygiene,
Hazardous Materials, Personal Protective
Equipment, and Lockout/Tagout.
Note: Requires appropriate clothing for field
exercise.
OSHA 7205 - Health Hazard
Awareness
This introductory course addresses the four
core elements of an effective safety and health
program with strategies & techniques that are
critical to each element’s proper management.
The course is designed for the small employer,
business owner or manager designated with the
responsibility to develop and manage a firm’s
safety and health program or system. The training is also suitable for employees and employee
representatives responsible for improving safety
and health in the workplace.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
Dates
Apr 12
Jun 21
Location San Diego Tempe Section ID
110941
111333
Section ID
110940
(800) 358-9206 • osha.ucsd.edu
13
Courses
Throughout
California
Serving many communities throughout the
state, UCSD’s OTIEC offers authorized OSHA
Training courses and all of the required
courses to complete each of our certificates
within California.
Anaheim
Brookhurst Community Center
2271 W. Crescent Avenue
Anaheim, CA 92801
Bakersfield
New Location coming Soon.
Visit osha.ucsd.edu/Bakersfield
for more information.
Los Angeles
Figueroa Courtyard
261 South Figueroa
Los Angeles, CA 90012
Los Angeles
UCLA School of Public Health
650 Charles E. Young Dr, S.
Los Angeles, CA 90095
San Diego
OSHA Training Institute Education Center
UC San Diego Extension
404 Camino del Rio S., Ste 102
San Diego, CA 92108
OSHA 501 - Trainer Course in
Occupational Safety and Health
Standards for General Industry
OTIEC Trainer Courses
OSHA 500 - Trainer Course in
Occupational Safety and Health
Standards for the Construction
Industry
The focus of this TRAINER course is to prepare
students to teach the 10 and 30 Hour Outreach
classes. Course time is spent learning and practicing adult training techniques. Students will
participate in the development and delivery
of lectures during class. Thorough knowledge
of OSHA Construction Standards (CFR 1926) is
required. Following successful completion of
the written exam, students become authorized
OSHA Trainers in the 10 and 30 Hour Outreach
Programs. Laptop recommended.
Note: IMPORTANT—ONLINE ENROLLMENT IS
NOT PERMITTED. A Verification of prerequisite Form must be sent in, along with your
OSHA 510 documentation, to obtain approval
to attend the course. The required prerequisites
are: OSHA 510 course and five years of construction safety experience. A college degree in
occupational safety and health, a CSP, CIH, CHST
or CSHM designation in the applicable training
area may be substituted for two years of experience with proper documentation.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Jan 25-28
Feb 1-4
Feb 16-19
Feb 29-Mar 3
Mar 7-10
Mar 14-17
Mar 21-24
Apr 4-7
Apr 4-7
Apr 18-21
May 2-5
Jun 6-9
Jun 13-16
Aug 1-4
Aug 8-11
Aug 15-18
Aug 22-25
Aug 29-Sep 1
Sep 12-15
Oct 3-6
Oct 31-Nov 3
Nov 14-17
Dec 5-8
Location San Diego Tempe Bakersfield Claremont Anaheim Sacramento Henderson Tucson Waipahu San Diego Tempe Reno Los Angeles San Diego Tempe
Bakersfield
Las Vegas
Claremont
Sacramento
San Diego Tempe
Reno
San Diego Section ID
110877
111291
111917
111919
112128
111922
111927
111929
112131
110944
111326
111938
112135
110982
111382
111968
111969
111970
111974
111050
111395
111986
111077
The focus of this Trainer course is to prepare
students to teach the 10 and 30 Hour Outreach
classes. Course time is spent learning and practicing adult training techniques. Students will
participate in the development and delivery of
lectures during class. Thorough knowledge of
OSHA General Industry Standards (CFR 1910) is
required. Upon successful course completion,
students become authorized OSHA Trainers in
the 10 and 30 Hour Outreach Programs. Laptop
recommended.
Note: IMPORTANT—ONLINE ENROLLMENT IS
NOT PERMITTED. A Verification of prerequisite Form must be sent in, along with your
OSHA 511 documentation, to obtain approval
to attend the course. The required prerequisites
are: OSHA 511 course and five years of general
industry safety experience. A college degree in
occupational safety and health, a CSP, CIH, OSHT
or CSHM designation in the applicable training
area may be substituted for two years of experience with proper documentation.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 1-4
Feb 29-Mar 3
Apr 11-14
May 16-19
May 16-19
May 23-26
Jun 6-9
Jul 18-21
Jul 18-21
Jul 25-28
Aug 1-4
Aug 15-18
Aug 22-25
Aug 29-Sep 1
Oct 10-13
Oct 24-27
Nov 7-10
Nov 14-17
Dec 5-8
Location San Diego Tempe Claremont Las Vegas San Diego Bakersfield Tempe Tucson
Waipahu Sacramento
Los Angeles San Diego Tempe
Reno
Claremont
Anaheim Bakersfield
San Diego Tempe
Section ID
110893
111313
111932
111950
110952
111953
111329
111960
112139
111963
112140
110987
111388
111971
111978
112146
111984
111067
111400
OTIEC Trainer Courses
San Diego (University City)
OSHA Training Institute Education Center
UC San Diego Extension
6256 Greenwich Dr.
San Diego, CA 92122
Sacramento
Sacramento Regional Builders Exchange
1331 T Street
Sacramento, CA 95811
14
UC San Diego Extension
Travel Plans
All travel plans must accommodate the
published course end time.
(800) 358-9206 • osha.ucsd.edu
OSHA 502 - Update for
Construction Industry Outreach
Trainers
Are you an active trainer in the Outreach
Program? Have you completed the Trainer
Course for the Construction Industry OSHA
500? You must be updated every four years on
training techniques, OSHA construction industry
standards, policies, and regulations. Once you
successfully complete the course, you are authorized to train for an additional four year term.
Bring current trainer card to class for verification of your status. Laptop recommended.
Note required prerequisite: OSHA 500 or OSHA
502 within four years. IMPORTANT—ONLINE
ENROLLMENT IS NOT PERMITTED. A Verification
of Prerequisite Form must be sent in prior to
enrollment, along with proof of your trainer
status. Acceptable forms of proof are: a copy
of your OSHA 500/OSHA 502 trainer card or
Certificate of completion.
Fee: $495
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 1-3
Feb 8-10
Feb 16-18
Feb 22-24
Feb 22-24
Mar 7-9
Apr 25-27
May 9-11
May 23-25
May 23-25
Jun 13-15
Aug 22-24
Aug 29-31
Sep 26-28
Oct 3-5
Oct 31-Nov 2
Location Los Angeles Las Vegas San Diego Tempe Waipahu Reno Claremont Sacramento San Diego Tucson Tempe San Diego Tempe
Claremont
Henderson
San Diego Section ID
112123
111914
110901
111311
12125
111920
111935
111941
110956
111952
111330
110991
111389
111976
111977
111058
OSHA 503 - Update for General
Industry Outreach Trainers
Are you an active trainer in the Outreach
Program? Have you completed the OSHA 501
- Trainer Course for General Industry? You
must be updated every 4 years on training techniques, OSHA general industry standards, policies, and regulations. Once you successfully complete the course, you are authorized to train for
an additional four year term. Must bring current
trainer card to class. Laptop recommended.
Note required prerequisite: OSHA 501 or OSHA
503 within four years. IMPORTANT—ONLINE
ENROLLMENT IS NOT PERMITTED. A Verification
of Prerequisite Form must be sent in prior to
enrollment, along with proof of your trainer
status. Acceptable forms of proof are: a copy
of your OSHA 501/OSHA 503 trainer card or
Certificate of completion.
Fee: $495
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 1-3
Feb 22-24
Feb 29-Mar 2
Mar 21-23
May 16-18
Jun 13-15
Jul 11-13
Aug 8-10
Sep 7-9
Oct 10-12
Oct 24-26
Oct 31-Nov 2
Location Sacramento Los Angeles San Diego Tempe Claremont Las Vegas Tempe
San Diego Tucson
Waipahu Tempe
San Diego Section ID
111912
112126
110905
111923
111948
111955
111378
110984
111972
112145
111394
111059
OSHA 5400 - Trainer Course in
Occupational Safety and Health
Standards for the Maritime
Industry
This is a Trainer Course for those interested in
teaching the 10 and 30 Hour Maritime Outreach
Program. Special emphasis is placed on required
Outreach topics, using OSHA standards as a
guide. Students are taught effective adult
instructional techniques. This course authorizes students to become Maritime Outreach
Trainers.
Note: IMPORTANT—ONLINE ENROLLMENT IS
NOT PERMITTED. A Verification of prerequisite
Form must be sent in, along with your OSHA
5410 documentation, to obtain approval to
attend the course. The required prerequisites
are: OSHA 5410 course and three years of
maritime safety experience. Additional requirements include two years of occupational safety
and health experience (with a broad focus) in
any industry; a college degree in occupational
safety and health, from an accredited college
or university; an ASP, CSP, CIH, CMC or CSHM
designation.
Location San Diego San Diego San Diego Participants will update their maritime trainer
status and be able to demonstrate continued
development by applying effective adult learning principles and training techniques to identify and explain maritime industry hazards and
corrective measures.
Note required prerequisite: OSHA 5400 or
OSHA 5402 within four years. IMPORTANT—
ONLINE ENROLLMENT IS NOT PERMITTED.
A Verification of Prerequisite Form must be sent
in prior to enrollment, along with proof of your
trainer status. Acceptable forms of proof are: a
copy of your OSHA 5400/OSHA 5402 trainer card
or Certificate of completion.
Fee: $675
Time: 8:00 a.m.-4:30 p.m.
Dates
Mar 7-9
Mar 21-23
Dec 5-7
Location San Diego Waipahu San Diego Section ID
110909
112129
111074
OSHA 5600 - Disaster Site Worker
Trainer Course
Experienced trainers will learn to present the
OSHA 7600 - Disaster Site Worker Course. You
will be able to apply elements of successful
training programs and will practice knowledge,
skills and attitudes through discussion, exercises
and presentations. You will receive lesson plans,
training materials and information on training
techniques and resources. You will be expected
to present a select portion of the Disaster
Site Worker Course. Re-certification is required
every four years.
Note: IMPORTANT—ONLINE ENROLLMENT IS
NOT PERMITTED. A Verification of prerequisite
Form must be sent in, along with your OSHA 500
or OSHA 501 and 40-Hour HAZWOPER documentation, to obtain approval to attend the
course. The required prerequisites are: OSHA
500 or OSHA 501 course, three years of safety training experience and completion of the
40-Hour HAZWOPER course.
Fee: $725
Time: 8:00 a.m.-4:30 p.m.
Dates
Nov 28-Dec 1
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates
Feb 22-25
Jun 6-9
Nov 7-10
OSHA 5402 - Maritime Industry
Trainer Update Course
Location San Diego Section ID
111072
Section ID
110904
110959
111064
OTIEC Trainer Courses
Course Credit Calculations
UCSD safety and UCSD OTIEC courses offer
several types of academic and industry credit.
See page 3
(800) 358-9206 • osha.ucsd.edu
15
UCSD Safety Courses
UCSD Safety Courses
EM385-1-1 40 Hour Safety
This course is for contractors, military and government employees who enforce or must comply
to the EM385-1-1 US Army Corps of Engineers
safety and health requirements. You will learn
procedures of the Navy and US Army Corps of
Engineers contracts, and the safety and health
requirements of the US Army Corps of Engineers
Safety and Health Requirements manual. Upon
completion, students receive an official OSHA
30 Hour card for Construction. Topics include:
Preparation of Site-Specific Accident Prevention
Plan (APP), Intro to OSHA, Site Safety Health
Officer’s Qualifications & Responsibilities,
Activity Hazard Analysis development, Site
Personnel training, Incident Response, Job site
Auditing, and Hazard Communication.
Section ID
110894
111319
110986
111924
Electrical High Voltage Standards
- Federal
OSHA classifies any use of electrical service
over 600 volts as high voltage. Regulations
and accepted industry standards state that
employers meet specific training requirements
for their employees who work with high voltage electrical installations. These rules apply to
commercial, industrial, and government sites
as well as electric utility generation, transmission and distribution installations. This course
provides information crucial to safely operate
your facility. Along with advance knowledge
of critical compliance issues, emphasis is placed
on hazard awareness and abatement methods. Topics Include: Fundamentals, Definitions,
Wiring Methods, Practices and Equipment,
Lockout/Tagout. Recommended prerequisite:
OSHA 3095.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates May 9-12 Location San Diego For employees working on or near equipment
energized above 600 volts, this intensive two
day training course is built around state requirements. Learn how to maintain a safe, hazard
free workplace by learning safety related information regarding state standards, equipment
safety practices, dealing with hazards and the
use of protective equipment. Topics include:
Personal Protective Equipment, Energized Parts,
Grounding, Medical Services/First Aid, and
Hazardous Energy Control.
Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Dates Jul 11-12 Location San Diego Section ID
110951
Fire and Life Safety
Specifically designed for safety professionals,
risk managers, supervisors, operations manager
and fire service personnel. Students will receive
a comprehensive knowledge of fire and safety
requirements in the workplace, and be introduced to the history leading to those requirements as well as the specific codes, standards
and regulations resulting from past incidents
and organizational efforts. Participants will
learn to apply the requirements to specific
workplace situations. Systems and equipment
used to provide Fire and Safety in the workplace
including proper maintenance and inspection
will be discussed.
Fee: $925
Time: 8:00 a.m.-4:30 p.m.
Section ID
110964
Dates May 16-20
Electrical Low Voltage Standards
- State
Fee: $925
Time: 8:00 a.m.-4:30 p.m.
Dates Location Feb 1-5 San Diego Mar 14-18 Tempe Aug 8-12 San Diego Sep19-23Tempe
Electrical High Voltage Standards
- State
Location San Diego
Section ID
110960
Get practical training so that your business
can maintain a safe, hazard free workplace.
This intensive two day training course is built
around state requirements for employees working on electrical installations and equipment.
Included are safety related information regarding state standards, equipment safety practices,
dealing with hazards and the use of protective
equipment. Topics include: Definitions, Wiring
Methods, Practices and Equipment, Lockout/
Tagout.
Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Dates Jul 14-15 Location San Diego Safety in the
Silver State
Section ID
110965
Electrical Safety Standards NFPA 70E - 2-Day
If you work on or near energized electrical systems, have a safety role at these sites or are an
emergency responder, this course is for you. The
new electrical safety standards (NFPA 70E) are
the next step to a safer electrical environment
in the workplace. Anyone who deals with hazards such as electrocutions, fires and explosions
should attend. Learn how to prevent serious disabling injuries, damage to equipment and work
sites and most importantly, save lives.
Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Dates Feb 16-17 Aug 17-18
Aug 22-23
Location San Diego Tempe
San Diego
With classes offered in “The City of Lights” and
“The Biggest Little City in the World,” UCSD’s
OTIEC proudly works with host sites committed
to providing safety training throughout Nevada.
Henderson
Section ID
110902
111384
110990
Nevada OSHA/SCATS
1301 N. Green Valley Pkwy, Ste 200
Henderson, NV 89074
Las Vegas
Associated General Contractors
150 N. Durango Drive, Ste 100
Las Vegas, NV 89145
Reno
AGC Nevada
5400 Mill Street
Reno, NV 89510
16
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
Trainer Course - Confined Space
Trainer Course - Rigging Safety
This course includes a basic overview of Federal
OSHA standards with main emphasis on Cal/
OSHA standards. Students will be coached
through a jobsite inspection process from the
opening conference to the closing conference.
Working group sessions will study actual court
cases highlighting preparation for a hearing,
burden of proof, affirmative defense and discovery. The overall objective of this course is
to enable students to better prepare for workplace inspections conducted by OSHA. Topics
Include: Fed OSHA and Cal OSHA, Litigation,
Injury Illness Prevention, Personal Protective
Equipment, and Respiratory Protection.
Gain the knowledge and skills to instruct a
confined space entry class within your organization. The course will cover advanced confined
space issues, teaching, resources, instructional
methodology and points on how to jazz up your
presentation. Students will be required to give a
ten minute presentation for evaluation by other
students.
This course covers advanced rigging principles,
safety requirements, and key considerations
for safe rigging. Students participating in this
course will be able to identify appropriate
rigging techniques; they will understand sling
angles and the stresses imposed. They will go
thru OSHA’s new regulations on qualifications
of riggers and the national consensus standards for rigging to include sling and hardware
inspections and rejection criteria. An extensive
use of hands-on practical techniques emphasizes the training and the course is completed
with a tour of an active rigging shop.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates Sep 19-22
Location San Diego
Section ID
111037
Learn the most commonly used safety inspection standards, tools and techniques in this
3-day course. Experience an organized approach
to inspecting and auditing projects to insure
OSHA compliance and injury prevention. Visit
both construction and general industry sites
to perform an inspection and prepare a final
report.
Section ID
110896
111321
111069
Scaffolding
During this course you will become familiar
with the OSHA compliance standards for various types of scaffolding including supported,
suspended, and aerial lifts. You will also learn
how scaffolds work and how to do basic load
analysis, as well as hands-on field exercises, the
OSHA standards for scaffolding, and resource
material. Topics include: Platforms, Bracing,
Guardrails, Falling Objects, Tie-Ins and Scaffold
Bracing, and Mobile Scaffolds.
Fee: $675
Time: 8:00 a.m.-4:30 p.m.
Dates Jan 19-21
Mar 14-16
Jul 25-27
Sep 7-9
Sep 12-14
Location San Diego
Tempe
San Diego
Tempe
Waipahu
Location San Diego
San Diego
Section ID
110947
111057
Continuation of the OSHA 3110 course, this
course teaches students how to apply the fall
protection standards, and teaches training techniques that are effective and develops an effective training course for both classroom and
hands-on in the field.
Fee: $250
Time: 8:00 a.m.-4:30 p.m.
Dates May 6
Dec 9
Location San Diego
San Diego
Section ID
110950
111080
Trainer Course - Forklift Safety
Fee: $675
Time: 8:00 a.m.-4:30 p.m.
Location San Diego
Tempe
San Diego
Dates Apr 28-29
Oct 27-28
Trainer Course - Fall Protection
Safety Inspection Techniques
Dates Feb 8-10
May 11-13
Nov 28-30
Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Participants will learn the OSHA requirements,
how they affect companies and how to comply with the standards. This course is designed
to give the tools and knowledge needed to
return to work and teach forklift operators
OSHA requirements. Trainers should have a
basic understanding of forklift operations and
procedures. Forklift operating experience is
helpful but not needed for this course. An
operational supervisor may be needed to assist
you in training and evaluation of your facility.
Topics Include: rough terrain, extendable boom
and vertical mast.
Fee: $750
Time: 8:00 a.m.-4:30 p.m.
Dates Apr 4-7
Jun 20-23
Sep 12-15
Location San Diego
San Diego
Tempe
Section ID
110938
110963
111386
Trainer Course - Trenching
This course reviews the Federal and State OSHA
requirements for excavation and trenching
activities. Emphasis will be placed on training
techniques, prevention strategies and practices
such as inspections, permitting procedures, soil
analysis, and competent person responsibilities.
Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Dates Feb 4-5
Sep 1-2
Location San Diego
San Diego
Section ID
110895
110994
Fee: $425
Time: 8:00 a.m.-4:30 p.m.
Dates Jun 6-7
Aug 15-16
Oct 10-11
Location San Diego
Tempe
San Diego
Section ID
110957
111383
111053
Section ID
110876
111320
110967
111385
112143
(800) 358-9206 • osha.ucsd.edu
17
UCSD Safety Courses
Laws and Regulations
UCSD’S OSHA TRAINING INSTITUTE EDUCATION CENTER INSTRUCTORS
The Heart of our Education Center
We take pride in our instructors and believe they are the heart of your
experience at UCSD’s OTIEC. Each instructor is hand-picked and dedicated to providing you with the knowledge you need.
They bring to the classroom a wealth of experience, up-to-date subject
matter expertise and a passion for sharing their insights and wisdom.
Our instructors include current and former state OSHA staff, published
industry authors, leaders of large organizations throughout the country and consultants within the Construction, Disaster Site, General
Industry, Maritime and military specialties.
Instructors
INSTRUCTORS LIST
Tristan Aldeguer, ASP, CHST
Russ Barringer, CSP, CSHM, MS
Jeff Beeler, CSTI
Mark Behrens, CSP
Mark E. Bipes, CIH, CSP
James Breay, MS, CIH
Bob Downey, BA, MPA, CSP, CPP
Michelle Eisenberg, MPH, RPT, CIE
Robert Fernandez, RSSP
Charles Geraci, CBCP
Harold Gribow, MS, CSP, ARM
Dave Hancock, BA,MA,CHDT
John Harr, BA, MHS, CSE
Bob Harrell, BA
Steve Healey, ASP, CHST, CUSA, STSC
Brian Heramb, CIH, FAIHA
Van Howell, BA, CSP, CET
Steven Irwin
Tracy Lawson, CSP, CET, CHST, CPEA
Jeff Lewis, MS, RSP, CSSM, DMT
John Marsden, CHST
John McHugh
Randy McPheeters, BA, MA, CSP
Dave Nelson, Master Electrician
Jim Newberry, CHST
Mark Norton, MAOM, RSP,CSSM
John O’Toole, Ph.D., RSSP
Tim Page-Bottorff, CSP
Suzy Shamsky, MPH, CIH, CSP
Thomas Stefanik, MS, CSP
Mary Sullivan, MS, CSP, OHST, CHST
Dan Tappen, MPH, CIH
Rick Wilson
For biographies and a current list of UCSD instructors, visit osha.ucsd.edu.
Courses in Arizona
For nearly 20 years, The American Society of Safety Engineers Chapters in Phoenix and Tucson and the Arizona Safety Education
Center have proudly offered authorized OSHA Training courses, as a host site of UCSD’s OSHA Training Institute Education Center,
throughout the Phoenix and Tucson areas.
We are proud to offer all of the courses required to complete the Professional Certificate in Occupational Health and Safety.
Arizona Course Locations
Phoenix
Tucson
Arizona Safety Education Center
201 East Southern Avenue, Ste 204
Tempe, AZ 85282
Arizona Dept. of Occupational
Safety & Health (ADOSH)
2675 East Broadway Boulevard
Tucson, AZ 85719
osha.ucsd.edu/Arizona
18
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
2016 Courses At-A-Glance, by Date
COURSE TYPE LOCATION
SECTION ID
OSHA 510 - OS&H Standards for the Construction Industry
COURSE TITLE
Jan 11-14
San Diego
110874
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jan 11-14
San Diego
110875
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 11-14
Tempe
111285
UCSD
Scaffolding
Jan 19-21
San Diego
110876
OTIEC
OSHA 3115 - Fall Protection
Jan 19-22
Tempe
111289
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 19-22
Bakersfield
111910
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Jan 25-28
San Diego
110877
OTIEC
OSHA 2225 - Respiratory Protection
Jan 25-28
San Diego
110878
OTIEC
OSHA 2055 - Cranes in Construction
Jan 25-28
Tempe
111295
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Jan 25-28
Claremont
111911
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 25-28
Waipahu
112116
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 25-28
Anaheim
112117
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Feb 1-3
San Diego
110879
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Feb 1-3
Sacramento
111912
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 1-3
Los Angeles
112123
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Feb 1-4
San Diego
110893
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Feb 1-4
Tempe
111291
UCSD
EM385-1-1 40 Hour Safety
Feb 1-5
San Diego
110894
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Feb 4
Sacramento
111913
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Feb 4
Los Angeles
112124
UCSD
Trainer Course - Trenching
Feb 4-5
San Diego
110895
UCSD
Safety Inspection Techniques
Feb 8-10
San Diego
110896
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 8-10
Las Vegas
111914
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Feb 8-11
Claremont
111915
OTIEC
OSHA 511 - OS&H Standards for General Industry
Feb 8-11
Tempe
111316
OTIEC
OSHA 5410 - OS&H Standards for the Maritime Industry
Feb 8-12
San Diego
110899
OTIEC
OSHA 7505 - Introduction to Accident Investigation
Feb 11-12
San Diego
110900
UCSD
Electrical Safety Standards - NFPA 70E
Feb 16-17
San Diego
110902
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 16-18
San Diego
110901
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Feb 16-19
Tempe
111309
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Feb 16-19
Sacramento
111916
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Feb 16-19
Bakersfield
111917
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Feb 19
San Diego
110903
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 22-24
Tempe
111311
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 22-24
Waipahu
112125
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Feb 22-24
Los Angeles
112126
OTIEC
OSHA 5400 - Trainer Course in Occupational Safety and Health for the Maritime Industry
Feb 22-25
San Diego
110904
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Feb 22-25
Henderson
111918
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Feb 25
Los Angeles
112127
OTIEC
Feb 29-Mar 2
San Diego
110905
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
OSHA 503 - Update for General Industry Outreach Trainers
Feb 29-Mar 3
San Diego
110906
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Feb 29-Mar 3
San Diego
110907
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Feb 29-Mar 3
Tempe
111313
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Feb 29-Mar 3
Claremont
111919
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Mar 4
San Diego
111081
OTIEC
OSHA 5402 - Maritime Industry Trainer Update Course
Mar 7-9
San Diego
110909
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Mar 7-9
Reno
111920
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Mar 7-10
San Diego
110910
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Mar 7-10
Tucson
111921
OTIEC
OSHA 2255 - Principles of Ergonomics
Mar 7-10
Tempe
111317
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Mar 7-10
Anaheim
112128
UCSD
Scaffolding
Mar 14-16
Tempe
111320
OTIEC
OSHA 6000 - Collateral Duty Course for other Federal Employees
Mar 14-17
San Diego
110911
(800) 358-9206 • osha.ucsd.edu
At-A-Glance (by Date)
DATES
OTIEC
19
UC San Diego Extension’s Occupational Safety & Health Department
At-A-Glance (by Date)
COURSE TYPE DATES
LOCATION
SECTION ID
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Mar 14-17
San Diego
110912
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Mar 14-17
Sacramento
111922
UCSD
EM385-1-1 40 Hour Safety
Mar 14-18
Tempe
111319
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Mar 21-23
Tempe
111923
OTIEC
OSHA 511 - OS&H Standards for General Industry
Mar 21-24
Claremont
111926
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Mar 21-24
Henderson
111927
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Mar 21-24
Los Angeles
112130
OTIEC
OSHA 5402 - Maritime Industry Trainer Update Course
Mar 21-22
Waipahu
112129
UCSD
Trainer Course - Rigging Safety
Apr 4-7
San Diego
110938
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Apr 4-7
San Diego
110939
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Apr 4-7
Tempe
111322
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Apr 4-7
Tucson
111929
OTIEC
OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Apr 4-7
Sacramento
111931
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Apr 4-7
Waipahu
112131
OTIEC
OSHA 7115 - Lockout/Tagout
Apr 11
San Diego
110940
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
Apr 11-13
Anaheim
112132
OTIEC
OSHA 2255 - Principles of Ergonomics
April 11-14
San Diego
110943
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Apr 11-14
Tempe
111323
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Apr 11-14
Claremont
111932
OTIEC
OSHA 5810 - Hazards & Standards for On-Shore Oil and Gas
Apr 11-15
Bakersfield
111933
OTIEC
OSHA 7500 - Introduction to Safety and Health Management
Apr 12
San Diego
110941
OTIEC
OSHA 7845 - Recordkeeping Rule Seminar
Apr 13
San Diego
110942
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Apr 18-21
San Diego
110944
OTIEC
OSHA 2225 - Respiratory Protection
Apr 18-21
Tempe
111324
OTIEC
OSHA 511 - OS&H Standards for General Industry
Apr 18-21
Las Vegas
111934
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
Apr 25-27
San Diego
110945
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Apr 25-27
Claremont
111935
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Apr 25-28
San Diego
110946
OTIEC
Apr 25-28
Tempe
111228
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Apr 25-28
Los Angeles
112133
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Apr 28
Claremont
111937
UCSD
Trainer Course - Confined Space
Apr 28-29
San Diego
110947
OTIEC
OSHA 511 - OS&H Standards for General Industry
May 2-5
San Diego
110948
OTIEC
OSHA 3115 - Fall Protection
May 2-5
San Diego
110949
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
May 2-5
Tempe
111326
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
May 2-5
Reno
111939
OTIEC
OSHA 511 - OS&H Standards for General Industry
May 2-5
Bakersfield
111940
UCSD
Trainer Course - Fall Proection
May 6
San Diego
110950
OTIEC
OSHA 7505 - Introduction to Accident Investigation
May 9-10
Tempe
111907
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
May 9-11
Sacramento
111941
UCSD
Electrical High Voltage Standards - Federal
May 9-12
San Diego
110951
UCSD
Safety Inspection Techniques
May 11-13
Tempe
111321
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
May 12
Sacramento
111947
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
May 16-18
Claremont
111948
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
May 16-19
San Diego
110952
OTIEC
OSHA 511 - OS&H Standards for General Industry
May 16-19
Tempe
111327
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
May 16-19
Las Vegas
111950
OTIEC
OSHA 5410 - Occupational Safety and Health Standards for the Maritime Industry
May 16-20
San Diego
110955
UCSD
Fire and Life Safety
May 16-20
San Diego
110960
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
May 19
Claremont
111951
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
May 23-25
San Diego
110956
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
May 23-25
Tucson
111952
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
May 23-25
Tempe
111328
20
COURSE TITLE
OSHA 3095 - Electrical Standards (Low Voltage Federal)
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
2016 Courses At-A-Glance, by Date
COURSE TYPE COURSE TITLE
LOCATION
SECTION ID
Bakersfield
111953
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
May 23-26
Los Angeles
112134
UCSD
Trainer Course - Forklift Safety
Jun 6-7
San Diego
110957
OTIEC
OSHA 2015 - Hazardous Materials
Jun 6-9
San Diego
110958
OTIEC
OSHA 5400 - Trainer Course in Occupational Safety and Health for the Maritime Industry
Jun 6-9
San Diego
110959
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jun 6-9
Tempe
111329
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Jun 6-9
Claremont
111954
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Jun 6-9
Reno
111938
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Jun 13-15
Tempe
111330
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Jun 13-15
Las Vegas
111955
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jun 13-16
Tucson
111956
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Jun 13-16
Los Angeles
112135
OTIEC
OSHA 7205 - Health Hazard Awareness
Jun 20
Tempe
111332
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Jun 20-23
San Diego
110962
UCSD
Trainer Course - Rigging Safety
Jun 20-23
San Diego
110963
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Jun 20-23
Bakersfield
112263
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jun 20-23
Waipahu
112136
OTIEC
OSHA 7500 -Introduction to Safety & Health Management
Jun 21
Tempe
111333
OTIEC
OSHA 7405 - Fall Hazard Awareness for the Construction Industry
Jun 22
Tempe
111334
OTIEC
OSHA 7845 - Recordkeeping Rule Seminar
Jun 23
Tempe
111335
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Jun 27-29
Tempe
111376
OTIEC
OSHA 2015 - Hazardous Materials
Jun 27-30
Tempe
112227
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jun 27-30
Sacramento
111958
UCSD
Electrical High Voltage Standards - State
Jul 11-12
San Diego
110964
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Jul 11-13
Tempe
111378
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jul 11-14
San Diego
110968
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Jul 11-14
Claremont
111959
OTIEC
OSHA 2225 - Respiratory Protection
Jul 11-14
Los Angeles
112137
UCSD
Electrical Low Voltage Stands - State
Jul 14-15
San Diego
110965
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jul 18-21
Tempe
111379
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jul 18-21
Tucson
111960
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jul 18-21
Bakersfield
111961
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jul 18-21
Los Angeles
112138
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jul 18-21
Waipahu
112139
UCSD
Scaffolding
Jul 25-27
San Diego
110967
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Jul 25-27
Claremont
111962
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jul 25-28
San Diego
110969
OTIEC
OSHA 2225 - Respiratory Protection
Jul 25-28
San Diego
110979
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Jul 25-28
Tempe
111380
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jul 25-28
Sacramento
111963
OTIEC
OSHA 2255 - Principles of Ergonomics
Aug 1-4
San Diego
110981
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 1-4
San Diego
110982
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Aug 1-4
San Diego
110983
OTIEC
OSHA 511 - OS&H Standards for General Industry
Aug 1-4
Tempe
111381
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Aug 1-4
Las Vegas
111964
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 1-4
Los Angeles
112140
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Aug 8-10
San Diego
110984
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Aug 8-11
San Diego
110985
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 8-11
Tempe
111382
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Aug 8-11
Claremont
111965
OTIEC
OSHA 511 - OS&H Standards for General Industry
Aug 8-11
Reno
111966
UCSD
EM385-1-1 40-Hour Safety
Aug 8-12
San Diego
110986
UCSD
Trainer Course - Forklift Safety
Aug 15-16
Tempe
111383
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 15-18
San Diego
110987
(800) 358-9206 • osha.ucsd.edu
At-A-Glance (by Date)
DATES
May 23-26
OTIEC
21
UC San Diego Extension’s Occupational Safety & Health Department
At-A-Glance (by Date)
COURSE TYPE DATES
LOCATION
SECTION ID
OTIEC
OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Aug 15-18
San Diego
110988
OTIEC
OSHA 3115 - Fall Protection
Aug 15-18
San Diego
110989
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Aug 15-18
Sacramento
111967
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 15-18
Bakersfield
111968
OTIEC
OSHA 2225 - Respiratory Protection
Aug 15-18
Waipahu
112141
UCSD
Electrical Safety Standards -NFPA 70E- 2 Day
Aug 17-18
Tempe
111384
UCSD
Electrical Safety Standards - NFPA 70E
Aug 22-23
San Diego
110990
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Aug 22-24
San Diego
110991
OTIEC
OSHA 2255 - Principles of Ergonomics
Aug 22-25
Los Angeles
112142
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 22-25
Tempe
111388
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 22-25
Las Vegas
111969
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Aug 25
San Diego
110992
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Aug 29-31
San Diego
110993
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Aug 29-31
Tempe
111389
OTIEC
OSHA 2055 - Cranes in Construction
Aug 29-Sep 1
San Diego
110995
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 29-Sep 1
Claremont
111970
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 29-Sep 1
Reno
111971
UCSD
Trainer Course - Trenching
Sep 1-2
San Diego
110994
UCSD
Scaffolding
Sep 7-9
Tempe
111385
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Sep 7-9
Tucson
111972
UCSD
Scaffolding
Sep 12-14
Waipahu
112143
UCSD
Trainer Course - Rigging Safety
Sep 12-15
Tempe
111386
OTIEC
OSHA 511 - OS&H Standards for General Industry
Sep 12-15
Claremont
111973
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Sep 12-15
Sacramento
111974
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Sep 19-22
San Diego
111035
OTIEC
OSHA 2015 - Hazardous Materials
Sep 19-22
San Diego
111036
UCSD
Laws and Regulations
Sep 19-22
San Diego
111037
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Sep 19-22
Bakersfield
111975
OTIEC
OSHA 511 - OS&H Standards for General Industry
Sep 19-22
Anaheim
112144
UCSD
EM385-1-1 40 Hour Safety
Sep 19-23
Tempe
111924
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Sep 26-28
Claremont
111976
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics Sep 26-28
Los Angeles
112422
OTIEC OSHA 3095 - Electrical Standards (Low Voltage Federal)
Sep 26-29
San Diego
111049
OTIEC
OSHA 3115 - Fall Protection
Sep 26-29
Tempe
111390
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Oct 3-5
Henderson
111977
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Oct 3-6
San Diego
111050
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Oct 3-6
San Diego
111052
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Oct 3-6
Tempe
111391
UCSD
Trainer Course - Forklift Safety
Oct 10-11
San Diego
111053
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Oct 10-12
Tempe
111392
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Oct 10-12
Waipahu
112145
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Oct 10-13
Claremont
111978
OTIEC
OSHA 511 - OS&H Standards for General Industry
Oct 10-13
Bakersfield
111979
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
Oct 24-26
San Diego
111054
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Oct 24-26
Tempe
111394
OTIEC
OSHA 3115 - Fall Protection
Oct 24-26
Claremont
111980
OTIEC
OSHA 511 - OS&H Standards for General Industry
Oct 24-27
San Diego
111055
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Oct 24-27
Reno
111981
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Oct 24-27
Anaheim
112146
OTIEC
OSHA 5410 - Occupational Safety and Health Standards for the Maritime Industry
Oct 24-28
San Diego
111056
UCSD
Trainer Course - Confined Space
Oct 27-28
San Diego
111057
OTIEC
OSHA 7505 - Introduction to Accident Investigation
Oct 31-Nov 1
Tucson
111982
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Oct 31-Nov 2
San Diego
111058
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Oct 31-Nov 2
San Diego
111059
22
COURSE TITLE
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
2016 Courses At-A-Glance, by Date
COURSE TYPE DATES
LOCATION
SECTION ID
OTIEC
OSHA 2225 - Respiratory Protection
COURSE TITLE
Oct 31-Nov 3
San Diego
111060
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Oct 31-Nov 3
Tempe
111395
OTIEC
OSHA 2015 - Hazardous Materials
Oct 31-Nov 3
Los Angeles
113261
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Nov 3
San Diego
111061
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Nov 7-9
San Diego
111062
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Nov 7-10
San Diego
111063
OTIEC
OSHA 5400 - Trainer Course in Occupational Safety and Health for the Maritime Industry
Nov 7-10
San Diego
111064
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Nov 7-10
Tempe
111396
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Nov 7-10
Sacramento
111983
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Nov 7-10
Bakersfield
111984
OTIEC
OSHA 3115 - Fall Protection
Nov 7-10
Waipahu
112150
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Nov 14-17
San Diego
111065
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Nov 14-17
San Diego
111067
OTIEC
OSHA 6000 - Collateral Duty Course for other Federal Employees
Nov 14-17
San Diego
111068
OTIEC
OSHA 511 - OS&H Standards for General Industry
Nov 14-17
Tempe
111397
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Nov 14-17
Las Vegas
111985
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Nov 14-17
Reno
111986
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Nov 14-17
Anaheim
112153
UCSD
Safety Inspection Techniques
Nov 28-30
San Diego
111069
OTIEC
OSHA 2255 - Principles of Ergonomics
Nov 28-Dec 1
San Diego
111071
OTIEC
OSHA 5600 - Disaster Site Worker Trainer Course
Nov 28-Dec 1
San Diego
111072
OTIEC
OSHA 6000 - Collateral Duty Course for other Federal Employees
Nov 28-Dec 1
Tempe
111398
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Nov 28-Dec 1
Claremont
111987
OTIEC
OSHA 7505 - Introduction to Accident Investigation
Dec 1-2
San Diego
111073
OTIEC
OSHA 5402 - Maritime Industry Trainer Update Course
Dec 5-7
San Diego
111074
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Dec 5-7
Waipahu
112155
OTIEC
OSHA 3115 - Fall Protection
Dec 5-8
San Diego
111075
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Dec 5-8
San Diego
111077
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Dec 5-8
Tempe
111400
UCSD
Trainer Course - Fall Proection
Dec 9
San Diego
111080
For a PDF version of the
At-A-Glance by date
and/or by location please
visit osha.ucsd.edu
Earn a Professional Certificate
from UC San Diego Extension’s OSHA
Training Institute and proudly wear
your safety hard hat!
All graduates of the Professional Certificate
in Safety and Health are eligible to receive
this free gift.
Safety Certificates
for Veterans
UC San Diego Extension’s Occupational Safety
and Health Department proudly offers two programs for US military veterans that have been
approved for use with VA educational benefits.
• Professional Certificate in Occupational Safety
& Health (see p. 7)
• Safety Specialist Certificate (see p.8)
To learn more about applying VA educational
benefits to our safety certificate programs, we
encourage veterans to contact unex-veterans@
ucsd.edu with any questions
(800) 358-9206 • osha.ucsd.edu
23
At-A-Glance (by Date)
Earn Your UCSD
Hard Hat!
UC San Diego Extension’s Occupational Safety & Health Department
At-A-Glance (by location)
COURSE TYPE DATES
LOCATION
SECTION ID
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
COURSE TITLE
Jan 25-28
Anaheim
112117
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Mar 7-10
Anaheim
112128
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
Apr 11-13
Anaheim
112132
OTIEC
OSHA 511 - OS&H Standards for General Industry
Sep 19-22
Anaheim
112144
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Oct 24-27
Anaheim
112146
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Nov 14-17
Anaheim
112153
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 19-22
Bakersfield
111910
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Feb 16-19
Bakersfield
111917
OTIEC
OSHA 5810 - Hazards & Standards for On-Shore Oil and Gas
Apr 11-15
Bakersfield
111933
OTIEC
OSHA 511 - OS&H Standards for General Industry
May 2-5
Bakersfield
111940
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
May 23-26
Bakersfield
111953
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Jun 20-23
Bakersfield
112263
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jul 18-21
Bakersfield
111961
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 15-18
Bakersfield
111968
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Sep 19-22
Bakersfield
111975
OTIEC
OSHA 511 - OS&H Standards for General Industry
Oct 10-13
Bakersfield
111979
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Nov 7-10
Bakersfield
111984
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Jan 25-28
Claremont
111911
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Feb 8-11
Claremont
111915
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Feb 29-Mar 3
Claremont
111919
OTIEC
OSHA 511 - OS&H Standards for General Industry
Mar 21-24
Claremont
111926
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Apr 11-14
Claremont
111932
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Apr 25-27
Claremont
111935
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Apr 28
Claremont
111937
OTIEC
May 16-18
Claremont
111948
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
May 19
Claremont
111951
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Jun 6-9
Claremont
111954
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Jul 11-14
Claremont
111959
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Jul 25-28
Claremont
111962
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Aug 8-11
Claremont
111965
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 29-Sep 1
Claremont
111970
OTIEC
OSHA 511 - OS&H Standards for General Industry
Sep 12-15
Claremont
111973
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Sep 26-28
Claremont
111976
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Oct 10-13
Claremont
111978
OTIEC
OSHA 3115 - Fall Protection
Oct 24-26
Claremont
111980
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Nov 28-Dec 1
Claremont
111987
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Feb 22-25
Henderson
111918
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Mar 21-24
Henderson
111927
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Oct 3-5
Henderson
111977
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 8-10
Las Vegas
111914
OTIEC
OSHA 511 - OS&H Standards for General Industry
Apr 18-21
Las Vegas
111934
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
May 16-19
Las Vegas
111950
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Jun 13-15
Las Vegas
111955
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Aug 1-4
Las Vegas
111964
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 22-25
Las Vegas
111969
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Nov 14-17
Las Vegas
111985
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 1-3
Los Angeles
112123
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Feb 4
Los Angeles
112124
OTIEC
Feb 22-24
Los Angeles
112126
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Feb 25
Los Angeles
112127
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
OSHA 503 - Update for General Industry Outreach Trainers
Mar 21-24
Los Angeles
112130
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Apr 25-28
Los Angeles
112133
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
May 23-26
Los Angeles
112134
24
OSHA 521 - OSHA Guide to Industrial Hygiene
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
2016 Courses At-A-Glance, by Location
COURSE TYPE DATES
LOCATION
SECTION ID
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Jun 13-16
Los Angeles
112135
OTIEC
OSHA 2225 - Respiratory Protection
Jul 11-14
Los Angeles
112137
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jul 18-21
Los Angeles
112138
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 1-4
Los Angeles
112140
OTIEC
OSHA 2255 - Principles of Ergonomics
Aug 22-25
Los Angeles
112142
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics Sep 26-28
Los Angeles
112422
OTIEC
OSHA 2015 - Hazardous Materials
Oct 31-Nov 3
Los Angeles
113261
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Mar 7-9
Reno
111920
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
May 2-5
Reno
111939
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Jun 6-9
Reno
111938
OTIEC
OSHA 511 - OS&H Standards for General Industry
Aug 8-11
Reno
111966
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 29-Sep 1
Reno
111971
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Oct 24-27
Reno
111981
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Nov 14-17
Reno
111986
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Feb 1-3
Sacramento
111912
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Feb 4
Sacramento
111913
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Feb 16-19
Sacramento
111916
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Mar 14-17
Sacramento
111922
OTIEC
OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Apr 4-7
Sacramento
111931
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
May 9-11
Sacramento
111941
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
May 12
Sacramento
111947
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jun 27-30
Sacramento
111958
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jul 25-28
Sacramento
111963
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Sep 12-15
Sacramento
111974
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Aug 15-18
Sacramento
111967
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Nov 7-10
Sacramento
111983
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 11-14
San Diego
110874
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jan 11-14
San Diego
110875
UCSD
Scaffolding
Jan 19-21
San Diego
110876
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Jan 25-28
San Diego
110877
OTIEC
OSHA 2225 - Respiratory Protection
Jan 25-28
San Diego
110878
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Feb 1-3
San Diego
110879
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Feb 1-4
San Diego
110893
UCSD
EM385-1-1 40 Hour Safety
Feb 1-5
San Diego
110894
UCSD
Trainer Course - Trenching
Feb 4-5
San Diego
110895
UCSD
Safety Inspection Techniques
Feb 8-10
San Diego
110896
OTIEC
OSHA 5410 - OS&H Standards for the Maritime Industry
Feb 8-12
San Diego
110899
OTIEC
OSHA 7505 - Introduction to Accident Investigation
Feb 11-12
San Diego
110900
UCSD
Electrical Safety Standards - NFPA 70E
Feb 16-17
San Diego
110902
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 16-18
San Diego
110901
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Feb 19
San Diego
110903
OTIEC
OSHA 5400 - Trainer Course in Occupational Safety and Health for the Maritime Industry
Feb 22-25
San Diego
110904
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Feb 29-Mar 2
San Diego
110905
Cal/OSHA OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Feb 29-Mar 3
San Diego
110906
OTIEC
Feb 29-Mar 3
San Diego
110907
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Mar 4
San Diego
111081
OTIEC
OSHA 5402 - Maritime Industry Trainer Update Course
Mar 7-9
San Diego
110909
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Mar 7-10
San Diego
110910
OTIEC
OSHA 6000 - Collateral Duty Course for other Federal Employees
Mar 14-17
San Diego
110911
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Mar 14-17
San Diego
110912
UCSD
Trainer Course - Rigging Safety
Apr 4-7
San Diego
110938
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Apr 4-7
San Diego
110939
OTIEC
OSHA 7115 - Lockout/Tagout
Apr 11
San Diego
110940
OSHA 521 - OSHA Guide to Industrial Hygiene
(800) 358-9206 • osha.ucsd.edu
At-A-Glance (by location)
COURSE TITLE
25
UC San Diego Extension’s Occupational Safety & Health Department
At-A-Glance (by location)
COURSE TYPE DATES
LOCATION
SECTION ID
OTIEC
OSHA 2255 - Principles of Ergonomics
April 11-14
San Diego
110943
OTIEC
OSHA 7500 - Introduction to Safety and Health Management
Apr 12
San Diego
110941
OTIEC
OSHA 7845 - Recordkeeping Rule Seminar
Apr 13
San Diego
110942
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Apr 18-21
San Diego
110944
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
Apr 25-27
San Diego
110945
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Apr 25-28
San Diego
110946
UCSD
Trainer Course - Confined Space
Apr 28-29
San Diego
110947
OTIEC
OSHA 511 - OS&H Standards for General Industry
May 2-5
San Diego
110948
OTIEC
OSHA 3115 - Fall Protection
May 2-5
San Diego
110949
UCSD
Trainer Course - Fall Proection
May 6
San Diego
110950
UCSD
Electrical High Voltage Standards - Federal
May 9-12
San Diego
110951
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
May 16-19
San Diego
110952
OTIEC
OSHA 5410 - Occupational Safety and Health Standards for the Maritime Industry
May 16-20
San Diego
110955
UCSD
Fire and Life Safety
May 16-20
San Diego
110960
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
May 23-25
San Diego
110956
UCSD
Trainer Course - Fall Proection
Jun 6-7
San Diego
110957
OTIEC
OSHA 2015 - Hazardous Materials
Jun 6-9
San Diego
110958
OTIEC
OSHA 5400 - Trainer Course in Occupational Safety and Health for the Maritime Industry
Jun 6-9
San Diego
110959
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Jun 20-23
San Diego
110962
UCSD
Trainer Course - Rigging Safety
Jun 20-23
San Diego
110963
UCSD
Electrical High Voltage Standards - State
Jul 11-12
San Diego
110964
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jul 11-14
San Diego
110968
UCSD
Electrical Low Voltage Stands - State
Jul 14-15
San Diego
110965
UCSD
Scaffolding
Jul 25-27
San Diego
110967
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jul 25-28
San Diego
110969
OTIEC
OSHA 2225 - Respiratory Protection
Jul 25-28
San Diego
110979
OTIEC
OSHA 2255 - Principles of Ergonomics
Aug 1-4
San Diego
110981
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 1-4
San Diego
110982
Cal/OSHA OSHA 5119 - Cal/OSHA Standards for General Industry
Aug 1-4
San Diego
110983
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Aug 8-10
San Diego
110984
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Aug 8-11
San Diego
110985
UCSD
EM385-1-1 40-Hour Safety
Aug 8-12
San Diego
110986
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 15-18
San Diego
110987
OTIEC
OSHA 5109 - Cal/OSHA Standards for the Construction Industry
Aug 15-18
San Diego
110988
OTIEC
OSHA 3115 - Fall Protection
Aug 15-18
San Diego
110989
UCSD
Electrical Safety Standards - NFPA 70E
Aug 22-23
San Diego
110990
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Aug 22-24
San Diego
110991
Cal/OSHA OSHA 5029 - Cal/OSHA Update for Construction Industry Outreach Trainers
Aug 25
San Diego
110992
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Aug 29-31
San Diego
110993
OTIEC
OSHA 2055 - Cranes in Construction
Aug 29-Sep 1
San Diego
110995
UCSD
Trainer Course - Trenching
Sep 1-2
San Diego
110994
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Sep 19-22
San Diego
111035
OTIEC
OSHA 2015 - Hazardous Materials
Sep 19-22
San Diego
111036
UCSD
Laws and Regulations
Sep 19-22
San Diego
111037
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Sep 26-29
San Diego
111049
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Oct 3-6
San Diego
111050
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Oct 3-6
San Diego
111052
UCSD
Trainer Course - Forklift Safety
Oct 10-11
San Diego
111053
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
Oct 24-26
San Diego
111054
OTIEC
OSHA 511 - OS&H Standards for General Industry
Oct 24-27
San Diego
111055
OTIEC
OSHA 5410 - Occupational Safety and Health Standards for the Maritime Industry
Oct 24-28
San Diego
111056
UCSD
Trainer Course - Confined Space
Oct 27-28
San Diego
111057
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Oct 31-Nov 2
San Diego
111058
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Oct 31-Nov 2
San Diego
111059
26
COURSE TITLE
UC San Diego Extension
(800) 358-9206 • osha.ucsd.edu
2016 Courses At-A-Glance, by Location
COURSE TYPE COURSE TITLE
LOCATION
SECTION ID
San Diego
111060
Cal/OSHA OSHA 5039 - Cal/OSHA Update for General Industry Trainers
Nov 3
San Diego
111061
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Nov 7-9
San Diego
111062
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Nov 7-10
San Diego
111063
OTIEC
OSHA 5400 - Trainer Course in Occupational Safety and Health for the Maritime Industry
Nov 7-10
San Diego
111064
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Nov 14-17
San Diego
111065
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Nov 14-17
San Diego
111067
OTIEC
OSHA 6000 - Collateral Duty Course for other Federal Employees
Nov 14-17
San Diego
111068
UCSD
Safety Inspection Techniques
Nov 28-30
San Diego
111069
OTIEC
OSHA 2255 - Principles of Ergonomics
Nov 28-Dec 1
San Diego
111071
OTIEC
OSHA 5600 - Disaster Site Worker Trainer Course
Nov 28-Dec 1
San Diego
111072
OTIEC
OSHA 7505 - Introduction to Accident Investigation
Dec 1-2
San Diego
111073
OTIEC
OSHA 5402 - Maritime Industry Trainer Update Course
Dec 5-7
San Diego
111074
OTIEC
OSHA 3115 - Fall Protection
Dec 5-8
San Diego
111075
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Dec 5-8
San Diego
111077
UCSD
Trainer Course - Fall Proection
Dec 9
San Diego
111080
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 11-14
Tempe
111285
OTIEC
OSHA 3115 - Fall Protection
Jan 19-22
Tempe
111289
OTIEC
OSHA 2055 - Cranes in Construction
Jan 25-28
Tempe
111295
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Feb 1-4
Tempe
111291
OTIEC
OSHA 511 - OS&H Standards for General Industry
Feb 8-11
Tempe
111316
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Feb 16-19
Tempe
111309
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 22-24
Tempe
111311
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Feb 29-Mar 3
Tempe
111313
OTIEC
OSHA 2255 - Principles of Ergonomics
Mar 7-10
Tempe
111317
UCSD
Scaffolding
Mar 14-16
Tempe
111320
UCSD
EM385-1-1 40 Hour Safety
Mar 14-18
Tempe
111319
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Mar 21-23
Tempe
111923
OTIEC
OSHA 521 - OSHA Guide to Industrial Hygiene
Apr 4-7
Tempe
111322
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Apr 11-14
Tempe
111323
OTIEC
OSHA 2225 - Respiratory Protection
Apr 18-21
Tempe
111324
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Apr 25-28
Tempe
111228
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
May 2-5
Tempe
111326
OTIEC
OSHA 7505 - Introduction to Accident Investigation
May 9-10
Tempe
111907
UCSD
Safety Inspection Techniques
May 11-13
Tempe
111321
OTIEC
OSHA 511 - OS&H Standards for General Industry
May 16-19
Tempe
111327
OTIEC
OSHA 2264 - Permit-Required Confined Space Entry
May 23-25
Tempe
111328
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jun 6-9
Tempe
111329
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Jun 13-15
Tempe
111330
OTIEC
OSHA 7205 - Health Hazard Awareness
Jun 20
Tempe
111332
OTIEC
OSHA 7500 -Introduction to Safety & Health Management
Jun 21
Tempe
111333
OTIEC
OSHA 7405 - Fall Hazard Awareness for the Construction Industry
Jun 22
Tempe
111334
OTIEC
OSHA 7845 - Recordkeeping Rule Seminar
Jun 23
Tempe
111335
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Jun 27-29
Tempe
111376
OTIEC
OSHA 2015 - Hazardous Materials
Jun 27-30
Tempe
112227
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Jul 11-13
Tempe
111378
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jul 18-21
Tempe
111379
OTIEC
OSHA 2045 - Machinery and Machine Guarding Standards
Jul 25-28
Tempe
111380
OTIEC
OSHA 511 - OS&H Standards for General Industry
Aug 1-4
Tempe
111381
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Aug 8-11
Tempe
111382
UCSD
Trainer Course - Forklift Safety
Aug 15-16
Tempe
111383
UCSD
Electrical Safety Standards -NFPA 70E- 2 Day
Aug 17-18
Tempe
111384
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Aug 22-25
Tempe
111388
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Aug 29-31
Tempe
111389
OSHA 2225 - Respiratory Protection
(800) 358-9206 • osha.ucsd.edu
At-A-Glance (by location)
DATES
Oct 31-Nov 3
OTIEC
27
UC San Diego Extension’s Occupational Safety & Health Department
At-A-Glance (by location)
COURSE TYPE COURSE TITLE
DATES
LOCATION
SECTION ID
UCSD
Scaffolding
Sep 7-9
Tempe
111385
UCSD
Trainer Course - Rigging Safety
Sep 12-15
Tempe
111386
UCSD
EM385-1-1 40 Hour Safety
Sep 19-23
Tempe
111924
OTIEC
OSHA 3115 - Fall Protection
Sep 26-29
Tempe
111390
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Oct 3-6
Tempe
111391
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Oct 10-12
Tempe
111392
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Oct 24-26
Tempe
111394
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Oct 31-Nov 3
Tempe
111395
OTIEC
OSHA 3095 - Electrical Standards (Low Voltage Federal)
Nov 7-10
Tempe
111396
OTIEC
OSHA 511 - OS&H Standards for General Industry
Nov 14-17
Tempe
111397
OTIEC
OSHA 6000 - Collateral Duty Course for other Federal Employees
Nov 28-Dec 1
Tempe
111398
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Dec 5-8
Tempe
111400
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Mar 7-10
Tucson
111921
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Apr 4-7
Tucson
111929
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
May 23-25
Tucson
111952
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jun 13-16
Tucson
111956
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jul 18-21
Tucson
111960
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Sep 7-9
Tucson
111972
OTIEC
OSHA 7505 - Introduction to Accident Investigation
Oct 31-Nov 1
Tucson
111982
OTIEC
OSHA 510 - OS&H Standards for the Construction Industry
Jan 25-28
Waipahu
112116
OTIEC
OSHA 502 - Update for Construction Industry Outreach Trainers
Feb 22-24
Waipahu
112125
OTIEC
OSHA 5402 - Maritime Industry Trainer Update Course
Mar 21-22
Waipahu
112129
OTIEC
OSHA 500 - Trainer Course in OS&H for the Construction Industry
Apr 4-7
Waipahu
112131
OTIEC
OSHA 511 - OS&H Standards for General Industry
Jun 20-23
Waipahu
112136
OTIEC
OSHA 501 - Trainer Course in OS&H for General Industry
Jul 18-21
Waipahu
112139
OTIEC
OSHA 2225 - Respiratory Protection
Aug 15-18
Waipahu
112141
UCSD
Scaffolding
Sep 12-14
Waipahu
112143
OTIEC
OSHA 503 - Update for General Industry Outreach Trainers
Oct 10-12
Waipahu
112145
OTIEC
OSHA 3115 - Fall Protection
Nov 7-10
Waipahu
112150
OTIEC
OSHA 3015 - Excavation, Trenching and Soil Mechanics
Dec 5-7
Waipahu
112155
U.S. Army
CP-12 Program
For a PDF version of the
At-A-Glance by date
and/or by location please
visit osha.ucsd.edu
28
OSHA Training
on Oahu
A part of the Department of the Army Civilian
(DAC) career programs, the Army Safety and
Occupational Health Career Management Program
(CP-12) was designed to provide the Army with the
well qualified, trained, and led Civilian Safety and
Occupational Health professionals needed to meet
the Army’s current and future needs.
Some of UCSD’s OTIEC courses will meet the
requirements of this rigorous program:
• OSHA 510 • OSHA 2015 • OSHA 2264
• OSHA 511 • OSHA 225 • OSHA 3095
• OSHA 521
For more information on the CP-12 program, visit
safety.army.mil/CP-12
UC San Diego Extension
Authorized OSHA numbered courses are available in our Hawaii classroom–conveniently
located minutes from the Honolulu International
Airport, world famous Waikiki Beach and the
legendary North Shore.
Honolulu
Construction Training Center
of the Pacific
94-487 Akoki Street
Waipahu, HI 96797
(800) 358-9206 • osha.ucsd.edu
TRAINING INSTITUTE
OCCUPATIONAL
SAFETY AND
EDUCATION CENTER
HEALTH DEPARTMENT
ENROLLMENT FORM
Enrolling is Easy
PLEASE PROVIDE YOUR PRIORITY CODE BY REFERRING TO THE FIRST THREE DIGITS OF THE N
­ UMBER ON THE TOP OF YOUR MAILING
LABEL (RIGHT ABOVE THE NAME)
Web:
o MS.
o MRS.
o MISS
o MR.
osha.ucsd.edu
o DR.
STUDENT I.D./PID #
Mail:
NAME
LAST
FIRST
OSHA Training Institute
UCSD Extension
404 Camino del Rio South,
Suite 102
San Diego, CA 92108
M.I.
ADDRESS
CITY
STATE
–
PHONE
ZIP
–
DAY
Phone:
ALTERNATE
(800) 358-9206
EMAIL
Fax:
(619) 294-3861
NAME OF EMPLOYER
COURSE TITLE
SECTION ID
CREDIT OPTION (CHECK ONE)
FEE
o ACADEMIC (PASS/NO PASS)
o NO GRADE
o ACADEMIC (PASS/NO PASS)
o NO GRADE
o ACADEMIC (PASS/NO PASS)
o NO GRADE
$
o ACADEMIC (LETTER GRADE)
o ACADEMIC (LETTER GRADE)
$
o ACADEMIC (LETTER GRADE)
$
TOTAL FEES (MAKE CHECK PAYABLE TO UC REGENTS)
$
PAYMENT METHOD (FULL PAYMENT MUST ACCOMPANY THIS FORM)
o VISA/MASTERCARD/DISCOVER CARD/AMERICAN EXPRESS ­
CARD NUMBER
EXP DATE
–
–
o CASH/PERSONAL CHECK (PAYABLE TO UC REGENTS)
o PURCHASE ORDER (MUST BE ATTACHED)
–
CARD CODE
SIGNATURE OF CARD HOLDER
ADDITIONAL INFORMATION
FOR OSHA 500, 501, 502, 503, 5029, 5039, 5400, 5402,
5600 and 5602
You must be approved to take these courses. To obtain
a Verification of Enrollment:
• Please download the form from the OSHA 500, OSHA 501,
OSHA 502, OSHA 503, OSHA 5029, OSHA 5039, OSHA 5400,
OSHA 5402, OSHA 5600 and OSHA 5602 course pages at
OSHA.UCSD.EDU
• Request by email at OSHATRAINING@ucsd.edu
• Or call (800) 358-9206
If you have been approved, please provide us with the date
of your approval.
Approval Date: ________________________________
• Company’s complete name and address
• Purchase order number
• Invoicing address and telephone number
• Point of contact (name, email and telephone number)
• Student’s name, social security number, telephone
number, mailing address and email
Enrollment Form
REFUND POLICY
• Cancellations must be made at least two weeks prior to
the course start date to be eligible for a refund.
• Transfer requests prior to two weeks will be honored.
• Transfers within the two weeks prior to the course start
date will be allowed one time only.
• Students who do not show up for class and do not call
will not be refunded or transferred to another section.
PURCHASE ORDER ENROLLMENTS
All purchase orders must be provided on company letterhead. Faxed POs will be accepted; however, the original
PO must be received in our office at the address above
within five business days from the date the fax was received.
Individuals with questions regarding purchase orders should
telephone (858) 534-3117. UCSD Extension requires the following information on all purchase orders submitted:
• Section ID number, course title, course dates, and
course fee
• Authorizing signature(s)
• Payment terms are net 30 days
(800) 358-9206 • osha.ucsd.edu
29
OCCUPATIONAL SAFETY AND
HEALTH DEPARTMENT
9500 Gilman Dr., Dept. 0170-M
La Jolla, CA 92093-0170
Non-Profit Org.
U.S. Postage
PAID
San Diego, CA
Permit No. 1909
Earn Your
UC San Diego
Hard Hat!
SU15-1002
See page 5 for more details.
Cert no. XXX-XXX-000
Not Printed at State Expense
Certificate Programs
Professional Certificate
Safety Specialist Certificate
The UCSD Professional Certificate in
Occupational Safety and Health provides
experienced safety professionals important
workplace knowledge and practical experience
regarding safety and safety standards.
Professional Certificates offer concentrated
study in areas directly applicable to many jobs
and can add breadth and depth to existing
knowledge and skills. You can elect a single
certificate in Construction or General Industry,
or a Dual Certificate in both areas.
The Safety Specialist Certificate was
designed by the Occupational Safety
and Health Department at UC San Diego
Extension and the Associated Builders and
Contractors, San Diego Chapter (ABC).
It is an intensive, cohort-based program
that combines in-class education with
associated skills practice. Included in the
certificate program topics are all items
necessary for individuals to prepare for
entry-level safety jobs in the construction
industry, including an on-the-job internship.
Fundamentals Certificate
The Public Sector Safety and Health
Fundamentals Certificate Program supports
OSHA’s mission by training public sector
employees in occupational safety and
health to reduce incident rates for workers
in state and local governments (the
certificate program is highly applicable to
private industry workers as well).
Participants can choose from a variety
of topics such as occupational safety
and health standards for construction
or general industry, safety and health
management, accident investigation, fall
hazard awareness, and recordkeeping.
For more information on Certificate Programs, see page 6 or visit osha.ucsd.edu
Home of the
TRAINING INSTITUTE
EDUCATION CENTER