•
•
•

1. To determine the proper dose for HaloKlear biopolymers
2. To determine which products and in what combination will provide best results
3. To determine the proper injection rate when using liquid biopolymers
HaloKlear LiquiFloc 1% and LBP-2101 (supplied)
Several 1 liter clear jars for testing
2 to 3 liters of representative turbid water sample to be treated
1. Obtain 1 liter source sample water for testing
2. Add 1 drop of HaloKlear LiquiFloc 1%
3. Shake sample, then let stand for several minutes
4. Repeat steps 2 through 4 as needed until flocculation occurs and desired result reached. Count the
number of drops used.
Step 1:
1. Obtain 1 Liter of source sample water for testing
2. Add 1 drop of HaloKlear LBP-2101
3. Shake sample
4. Add 1 drop of HaloKlear LiquiFloc 1%
5. Shake sample, then let stand for several minutes
6. Repeat steps 2 through 6 as needed until flocculation occurs and desired results reached. Count
the number of drops used and continue on to Step 2.
Step 2:
1. Obtain 1 liter of source sample water for testing
2. Once Step 1 above has been concluded, add the total number of drops of LBP-2101 all at once
and shake well.
3. Add 1 drop of HaloKlear LiquiFloc 1%
4. Shake sample and let stand for several minutes
5. Repeat steps 3-4 as needed until flocculation occurs and desired results reached. Count the
number
Note: In a liter, each drop of HaloKlear LBP-2101 is equal to 0.5ppm active (50 ppm of product). Each drop of HaloKlear LiquiFloc 1% is equal to 0.5ppm active.
For laboratory method using a dilution series for obtaining results, please contact HaloKlear at info@haloklear.com. If you have any questions, please contact HaloKlear at 1-888-282-6766.

Injection Rate Table Directions:
1. Determine the target flow rate (left hand column).
2. Locate the dose (top row) that was determined from the jar test method for single biopolymer
and the jar test method for dual biopolymer test above.
3. The Injection Rate Table is designed for HaloKlear LBP-2101 and HaloKlear Liquifloc 1%.
Determine the rate in milliliters per min (mL/min) or gallons per hour (gph).
4. If using HaloKlear LiquiFloc 2% instead of LiquiFloc 1%, divide the value from step C by 2. If
using HaloKlear LiquiFloc 3% divide the value from step C by 3.
*For accurate dosing, refer to the HaloKlear Dose Calculator.
0.25 mg/L
(0.25 ppm)
100 gpm 9.4 mL/min. or 0.15 gph
200 gpm 19 mL/min. or
0.30 gph
0.5 mg/L
(0.5 ppm)
19 mL/min. or
0.30 gph
38 mL/min. or
0.60 gph
0.75 mg/L
(0.75 ppm)
28 mL/min. or
0.45 gph
57 mL/min. or
0.90 gph
300 gpm 28 mL/min. or
0.45 gph
400 gpm 38 mL/min. or
0.60 gph
500 gpm 47 mL/min. or
0.75 gph
600 gpm 57 mL/min. or
0.90 gph
700 gpm 66 mL/min. or
1.0 gph
800 gpm 75 mL/min. or
1.2 gph
900 gpm 85 mL/min. or
1.3 gph
1000 gpm 94 mL/min. or
1.5 gph
57 mL/min. or
0.90 gph
75 mL/min. or
1.2 gph
94 mL/min. or
1.5 gph
110 mL/min. or 1.8 gph
130 mL/min. or 2.1 gph
150 mL/min. or 2.4 gph
170 mL/min. or 2.7 gph
190 mL/min. or 3.0 gph
85 mL/min. or
1.3 gph
110 mL/min. or 1.8 gph
140 mL/min. or 2.2 gph
170 mL/min. or 2.7 gph
200 mL/min. or 3.1 gph
230 mL/min. or 3.6 gph
250 mL/min. or 4.0 gph
280 mL/min. or 4.5 gph
1.0 mg/L
(1.0 ppm)
38 mL/min. or
0.60 gph
75 mL/min. or
1.2 gph
110 mL/min. or 1.8 gph
150 mL/min. or 2.4 gph
190 mL/min. or 3.0 gph
230 mL/min. or 3.6 gph
260 mL/min. or 4.2 gph
300 mL/min. or 4.8 gph
340 mL/min. or 5.4 gph
380 mL/min. or 6.0 gph
Injection Rate Table Directions
A. Determine the target flow rate (left hand column).

Each HaloKlear GelFloc or DBP-2100 sock will normally treat 100,000 to 125,000 gallons of turbid water. Some applications may allow the sock to treat more water.
One HaloKlear GelFloc FS or DBP-2100 FS sock in 100,000 gallons of water will have an average dose of 2.64 mg/L or 2.11 mg/L if 125,000 gallons are treated.
The HaloKlear Residual Biopolymer Test Kit can detect the presence of biopolymer at less than 0.1 mg/L, below toxicity concerns.
HaloKlear LiquiFloc 1%
Classic Strength
• Proven track record of treating billions of
gallons of stormwater
• Meets even the most stringent regulatory
requirements
• Easily used, even in cold climate applications
HaloKlear GelFloc
Flocculant/Clarifier
• Provides consistent performance
• Segmented to prevent bunching for maximum
effectiveness
• Can be used in settling, enhanced filtration,
and pretreatment
• Contains a substantially higher percentage of
chitosan than liquid forms
HaloKlear LBP-2101
Natural Biopolymer Charging Agent
• 100% biodegradable using natural ingredients
• Used in conjunction with HaloKlear flocculants
• Liquid form for highly accurate dosing
requirements
HaloKlear DBP-2100
Natural Biopolymer Charging Agent
• 100% biodegradable using natural ingredients
• Used in conjunction with HaloKlear flocculants
• Dry concentrate for cost effective applications
and easy handling
HaloSource, Inc.
HaloKlear is a division of HaloSource, Inc. HaloSource is a recognized worldwide leader in clean water and antimicrobial technology and a creator of cutting-edge solutions that benefit people and the planet.
Founded in 2002 in Seattle, Washington, HaloSource has grown to become an influential global innovator with offices and processing plants all over the world, including Bangalore, India and China.
We are partnering with top companies and thought leaders across the globe to make water better.
HaloSource, Inc.
1725 220th St SE, Ste 103
Bothell, WA 98021
Telephone: 425-881-6464 Fax: 425-882-2476 www.halosource.com
HaloKlear is a registered trademark of
HaloSource, Inc. ©2013 HaloSource, Inc.