Multifunction DAQ Accessory and
Cable Selection Guides
NI Cable Design Advantages
Accessories
The cables designated “EP” are the most commonly used data
acquisition device cables. Each type of cable is designed to work
specifically with the NI Multifunction DAQ devices to preserve signal
integrity with these technologies:
Cables
Ribbon.................................................................................................3
Shielded...............................................................................................3
RTSI Bus..............................................................................................4
Signal Conditioning ...............................................................................4
Connector Blocks ...................................................................................4
BNC.....................................................................................................4
Screw Terminals..................................................................................4
Custom Connectivity .............................................................................5
Seperate digital and
analog sections
Twisted pairs for
critical digital I/O
Individually-shielded
twisted pairs for
all analog inputs
Large (20 AWG) conductor
for +5V Lines
Page
Use the following tables to choose the most appropriate cables
and accessories.
Double ground shield
Individually-shielded
analog outputs
PVC jacket
Figure 1. SH68-68-EP Cable
M Series
NI 6220
NI 6221
NI 6224
NI 6250
NI 6251
NI 6280
NI 6281
NI 6225
NI 6229
NI 6254
NI 6259
NI 6284
NI 6289
Feature
Noise-reducing
Connect to…
SCC portable signal
signal conditioning
Connector1
0 or 1
Cable
SHC68-68-EPM
Cable Adapter
–
Accessory
See ni.com/sigcon
Noise-reducing
SCXI high-performance
signal-conditioning
Screw terminals
BNC terminal block
50-pin connector
Screw terminals
50-pin connector
0 only
SHC68-68-EPM
–
See ni.com/sigcon
0 or 1
0 or 1
SHC68-68-EPM
SHC68-68-EPM
SHC68-68-EPM
SHC68-68
SHC68-68
–
–
68M-50F MIO
–
68M-50F MIO
SCB-68 or TBX-68
BNC-2110,
Custom-built or third-party
CB-68LP of CB-68LPR
Custom-built or third-party
Noise-reducing
Noise-reducing
Low-cost
Low-cost
0 or 1
0 or 1
1
Connector 0 is available on all M Series devices. 0 and 1 are available on NI 62x4, NI 6225, and 62x9 devices. Connector 1 on the NI 6225 does not support SCC signal conditioning.
Product
68-pin E Series (except DAQCards):
NI 6070E
NI 6032E
NI 6052E
NI 6030E
NI 6040E
NI 6024E
NI 6036E
NI 6023E
NI 6034E
Feature
Noise-reducing
Noise-reducing
Noise-reducing
Noise-reducing
Noise-reducing
Low-cost
Low-cost
100-pin E Series
Noise-reducing
Noise-reducing
NI 6071E
Noise-reducing
NI 6033E
Noise-reducing
NI 6031E
Low-cost
NI 6025E
Low-cost
E Series DAQCards
Noise-reducing
Noise-reducing
NI DAQCard-6062E
Noise-reducing
NI DAQCard-6036E
Noise-reducing
NI DAQCard-6024E
Noise-reducing
Low-cost
Low-cost
S Series (except NI 6143)
Noise-reducing
Noise-reducing
NI 6133
NI 6115
Noise-reducing
NI 6111
NI 6132
Low-cost
NI 6120
NI 6110
S Series
Noise-reducing
Noise-reducing
NI 6143
Low-cost
2
B Series (PCI Only)
Noise-reducing
Noise-reducing
NI 6013
Noise-reducing
NI 6014
Low-cost
1
2
PXI only. USB B Series devices require no accessories.
Connect to…
SCC portable signal conditioning
SCXI high-performance signal-conditioning
Screw terminals
BNC terminal block
50-pin connector
Screw terminals
50-pin connector
Screw terminals
Screw terminals
BNC terminal block
50-pin connector
Screw terminals
50-pin connector
SCC portable signal conditioning
SCXI high-performance signal-conditioning
Screw terminals
BNC terminal block
50-pin connector
Screw terminals
50-pin connector
Screw terminals
Screw terminals1
BNC terminal block
Screw terminals
Screw terminals
BNC terminal block
Screw terminals
SCC portable signal conditioning
Screw terminals
BNC terminal block
Screw terminals
Cable
SH68-68-EP
SH68-68-EP
SH68-68-EP
SH68-68-EP
SH6850
RC68-68
RC68-68
SH100100
SH1006868
SH1006868
SH1006868
SH1006868
SH1006868
SHC68-68-EP
SHC68-68-EP
SHC68-68-EP
SHC68-68-EP
SHC68-68-EP
RC68-68
RC68-68
SH68-68-EP
N/A
SH68-68-EP
R6868
SHC68-68-EP
SHC68-68-EP
RC68-68
SH68-68-EP
SH68-68-EP
SH68-68-EP
R6868
Accessory
See ni.com/sigcon
See ni.com/sigcon
SCB-68 or TBX-68
BNC-2110, BNC-2120, or BNC-2190
Custom-built or third-party
CB-68LP of CB-68LPR
Custom-built or third-party
SCB100
2 SCB-68
BNC-2115 and BNC-2110, BNC-2120, or BNC-2190
Custom-built or third-party
CB68LP and/or CB68LPR
Custom-built or third-party
See ni.com/sigcon
See ni.com/sigcon
SCB-68 or TBX-68
BNC-2210, BNC-2120, or BNC 2190
Custom-built or third-party
CB-68LP of CB-68LPR
Custom-built or third-party
SCB-68
TB-2705
BNC-2110
CB-68LP
SCB-68
BNC-2110
CB-68LP
See ni.com/sigcon
SCB-68
BNC-2110, BNC-2120, or BNC 2190
CB-68LP
Multifunction DAQ Accessories and Cables
1
AI GND
2
AI GND
3
AI 0
34
33
32
31
30
29
28
AI 8
AI 2
AI GND
AI 11
AI SENSE
68
67
66
65
64
63
62
AI 12
AI 5
AI GND
AI 14
61
60
59
58
27
26
25
24
AI GND
AI 7
AI GND
AO GND
57
23
AI 15
56
55
22
21
AO 0
AO GND
D GND
54
53
20
19
NC
P0.0
P0.5
D GND
52
51
50
49
48
18
17
16
15
14
D GND
P0.3
PFI 11/P2.3
PFI 10/P2.2
D GND
47
46
13
12
D GND
45
44
11
10
PFI 0/P1.0
PFI 2/P1.2
PFI 3/P1.3
43
42
41
40
39
38
9
8
7
6
5
4
D GND
37
36
35
3
2
1
PFI 9/P2.1
P0.2
P0.7
PFI 4/P1.4
PFI 13/P2.5
PFI 15/P2.7
PFI 7/P1.7
PFI 8/P2.0
D GND
D GND
AI 1
AI GND
AI 3
AI GND
AI 4
CONNECTOR
(AI 16-31)
AI 10
CONNECTOR
(AI 0-15)
AI 0
AI GND
AI 9
AI 13
AI 6
AI GND
TERMINAL 68
TERMINAL 34
AO 1
TERMINAL 35
TERMINAL 1
P0.4
P0.1
P0.6
D GND
+5 V
TERMINAL 1
D GND
TERMINAL 35
TERMINAL 34
TERMINAL 68
PFI 1/P1.1
+5 V
D GND
PFI 5/P1.5
PFI 6/P1.6
D GND
PFI 12/P2.4
PFI 14/P2.6
P0.30
P0.28
P0.25
D GND
P0.22
P0.21
D GND
+5 V
D GND
P0.17
P0.16
D GND
D GND
+5 V
D GND
P0.14
P0.9
D GND
P0.12
NC
AO 3
AO 2
AI 31
AI GND
AI 22
AI 29
AI GND
AI 20
AI GND
AI 19
AI 26
AI GND
AI 17
AI 24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
D GND
D GND
P0.24
P0.23
P0.31
P0.29
P0.20
P0.19
P0.18
D GND
P0.26
P0.27
P0.11
P0.15
P0.10
D GND
P0.13
P0.8
D GND
AO GND
AO GND
AI GND
AI 23
AI 30
AI GND
AI 21
AI 28
AI SENSE 2
AI 27
AI GND
AI 18
AI 25
AI GND
AI 16
4
AI 8
5
AI 1
6
AI 9
7
AI 2
8
AI 10
9
AI 3
17 67
AI 7
18 68
AI 15
19 69
AI SENSE
AO 01
20 70
21 71
AO 11
AO EXT REF1
22 72
AO GND
23 73
D GND
24 74
P0.0
25 75
26 76
P0.4
P0.1
27 77
P0.5
28 78
P0.2
29 79
P0.6
30 80
P0.3
31 81
P0.7
32 82
D GND
33 83
+5 V
34 84
+5 V
35 85
AI HOLD COMP
EXT STROBE
PFI 0/AI START TRIG
PFI 1/AI REF TRIG
PFI 2/AI CONV CLK
PFI 3/CTR 1 SRC
PFI 4/CTR 1 GATE
PFI 7/AI SAMP CLK
PFI 8/CTR 0 SRC
PFI 9/CTR 0 GATE
AI 4 GND 1
AI 5 ñ 1
AI 6 + 1
AI 6 GND 1
AI 7 ñ 1
NC
NC
NC
P0.4
D GND
P0.1
P0.6
D GND
+5 V
D GND
D GND
PFI 0/AI START TRIG
PFI 1/AI REF TRIG
D GND
+5 V
D GND
PFI 5
PFI 6
D GND
PFI 9/CTR 0 GATE
CTR 0 OUT
FREQ OUT
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
AI 5 GND 1
AI 6 ñ 1
AI 7 + 1
AI 7 GND 1
NC
NC
D GND
P0.0
P0.5
D GND
P0.2
P0.7
P0.3
AI HOLD COMP
EXT STROBE*
D GND
PFI 2/AI CONV CLK
PFI 3/CTR 1 SOURCE
PFI 4/CTR 1 GATE
CTR 1 OUT
D GND
PFI 7/AI SAMP CLK
PFI 8/CTR 0 SOURCE
D GND
D GND
AI 8
34 68
AI 0
AI 10
31 65
AI 2
AI 1
AI GND
AI 3
AI GND
AI 4
AI GND
AI 13
AI 6
AI GND
AI 15
AO 0
1
AO 11
AO EXT REF1
P0.4
D GND
P0.1
P0.6
D GND
+5 V
D GND
D GND
PFI 0/AI START TRIG
PFI 1/AI REF TRIG
D GND
+5 V
D GND
PFI 5/AO SAMP CLK
PFI 6/AO START TRIG
D GND
PFI 9/CTR 0 GATE
CTR 0 OUT
FREQ OUT
33 67
32 66
30 64
29 63
28 62
AI GND
AI 9
AI GND
AI 11
AI SENSE
27 61
AI 12
24 58
AI 14
26 60
25 59
23 57
AI 5
AI GND
AI 7
22 56
AI GND
19 53
AO GND
D GND
21 55
20 54
18 52
17 51
16 50
15 49
14 48
13 47
12 46
11 45
10 44
9
8
7
6
5
4
3
2
1
43
42
41
40
39
38
37
36
35
AO GND
P0.0
P0.5
D GND
P0.2
P0.7
P0.3
AI HOLD COMP
EXT STROBE
D GND
PFI 2/AI CONV CLK
PFI 3/CTR 1 SRC
PFI 4/CTR 1 GATE
CTR 1 OUT
D GND
PFI 7/AI SAMP CLK
PFI 8/CTR 0 SRC
D GND
D GND
NC = No Connect
1 NC on NI 6122/6132
36 86
37 87
NI 6025E
2
P3.7
AI 8
4
54
D GND
3
5
6
AI 9
7
AI 2
AI 27
8
AI 10
9
AI 3
AI 28
AI 29
AI 23
15 65
16 66
17 67
18 68
19 69
AI SENSE
AI 41
20 70
AO 0
AI 34
21 71
AO 1
AI 42
22 72
NC
AI 35
23 73
AO GND
AI 43
24 74
D GND
AI SENSE 2
25 75
P0.0
AI GND
P0.4
AI 36
26 76
P0.1
AI 44
27 77
P0.5
AI 37
28 78
P0.2
AI 45
29 79
P0.6
AI 38
30 80
P0.3
AI 46
P0.7
AI 39
AI 47
AI 56
AI 49
36 86
AI 57
41 91
AI 51
PFI 3/CTR 1 SRC
AI 60
PFI 5/AO SAMP CLK
39 89
40 90
AI 50
AI 58
42 92
AI 59
45 95
AI 53
43 93
44 94
46 96
47 97
48 98
49 99
50 100
PFI 0/AI START TRIG
AI 52
PFI 4/ CTR 1 GATE
42 92
CTR 1 OUT
AI 54
AI 63
D GND
P3.3
D GND
P3.2
D GND
P3.1
D GND
P3.0
D GND
P2.7
D GND
P2.6
D GND
P2.5
D GND
P2.4
D GND
P2.3
D GND
P2.2
D GND
P2.1
D GND
D GND
P1.7
P1.6
D GND
P1.5
D GND
P1.4
D GND
P1.3
44 94
D GND
43 93
45 95
CTR 0 OUT
49 99
FREQ OUT
P3.4
41 91
46 96
PFI 9/CTR 0 GATE
AI 55
40 90
PFI 7/AI SAMP CLK
PFI 8/CTR 0 SRC
AI 62
38 88
39 89
PFI 6/AO START TRIG
AI 61
37 87
PFI 1/AI REF TRIG
PFI 2/AI CONV CLK
D GND
D GND
AI HOLD COMP
35 85
38 88
P3.5
34 84
33 83
EXT STROBE
P3.6
P2.0
D GND
+5 V
D GND
31 81
32 82
+5 V
AI 48
59
14 64
AI 15
AI 33
58
AI 13
AI 7
AI 40
57
13 63
AI 14
AI 32
56
12 62
AI 6
AI 31
55
11 61
AI 5
AI 30
53
AI 4
AI 12
AI 22
52
10 60
AI 11
AI 21
47 97
48 98
50 100
D GND
P1.2
P1.1
D GND
P1.0
D GND
+5 V
D GND
Figure 5. I/O Connector for
Figure 6. I/O Connector for
64-Channel E Series Devices
the NI 6025E Device
AI 0
AI GND
68
34
AI 8
67
33
AI 1
AI 9
66
32
AI GND
AI 2
65
31
AI 10
AI GND
AI 11
AI SENSE
64
30
AI 3
63
29
AI GND
62
28
AI 4
AI 12
61
27
AI GND
AI 5
AI GND
AI 14
AI 7
AI GND
AO GND
AO GND
D GND
P0.0
P0.5
D GND
P0.2
P0.7
P0.3
60
26
AI 13
59
25
AI 6
58
24
AI GND
57
23
AI 15
56
22
AO 0
55
21
AO 1
54
20
NC
53
19
P0.4
52
18
D GND
51
17
P0.1
50
16
P0.6
49
15
D GND
48
14
+5 V
47
13
D GND
PFI 11/P2.3
PFI 10/P2.2
D GND
PFI 2/P1.2
PFI 3/P1.3
PFI 4/P1.4
PFI 13/P2.5
PFI 15/P2.7
PFI 7/P1.7
PFI 8/P2.0
D GND
D GND
46
12
D GND
45
11
PFI 0/P1.0
44
10
PFI 1/P1.1
43
9
D GND
42
8
+5 V
41
7
D GND
40
6
PFI 5/P1.5
39
5
PFI 6/P1.6
38
4
D GND
37
3
PFI 9/P2.1
36
2
PFI 12/P2.4
35
1
PFI 14/P2.6
Figure 4. I/O Connector for 16-Channel
E Series and B Series Devices, except
51
2
AI 1
AI 19
NC = No Connect
Figure 3. S Series Devices Connector
1
AI 0
AI 18
AI 20
58
AI GND
AI GND
AI 25
59
57
16 66
AI 14
AI 24
AI 26
15 65
AI 6
AI 16
AI 17
56
14 64
AI 13
FREQ OUT
AI 0 +
AI 0 GND
AI 1 ñ
AI 2 +
AI 2 GND
AI 3 ñ
NC
AI 4 ñ 1
AI 5 + 1
55
13 63
AI 5
CTR 0 OUT
68
67
66
65
64
63
62
61
60
59
58
54
12 62
AI 12
PFI 5/AO SAMP CLK
34
33
32
31
30
29
28
27
26
25
24
53
11 61
AI 4
CTR 1 OUT
AI 0 ñ
AI 1 +
AI 1 GND
AI 2 ñ
AI 3 +
AI 3 GND
AI 4 + 1
52
10 60
AI 11
PFI 6/AO START TRIG
Figure 2. M Series Device Connectors
51
Figure 7. NI 6225 Pinout
CONNECTOR 1
(AI 16-79)
Connector 1
CONNECTOR 0
(AI 0-15)
Connector 0
TERMINAL 68
TERMINAL 35
TERMINAL 34
TERMINAL 1
TERMINAL 1
TERMINAL 34
TERMINAL 35
TERMINAL 68
AI 71
AI 78
AI 69
AI 68
AI 75
AI 66
AI 65
AI 72
AI GND
AI 55
AI 54
AI 61
AI 52
AI 51
AI 58
AI 49
AI 48
AI 47
AI 38
AI 37
AI 44
AI GND
AI 35
AI 34
AI 41
AI 32
AI 23
AI 30
AI 21
AI 20
AI 27
AI 18
AI 17
AI 24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
AI 79
AI 70
AI 77
AI 76
AI 67
AI 74
AI 73
AI 64
AI GND
AI 63
AI 62
AI 53
AI 60
AI 59
AI 50
AI 57
AI 56
AI 39
AI 46
AI 45
AI 36
AI SENSE 2
AI 43
AI 42
AI 33
AI 40
AI 31
AI 22
AI 29
AI 28
AI 19
AI 26
AI 25
AI 16
Multifunction DAQ Accessories and Cables
Ribbon I/O Cables
SH68-68-EP – A shielded 68-conductor cable terminated with
R6868 – A low-cost, 68-conductor flat ribbon cable terminated with
two 68-pin female 0.050 series D-type connectors. This cable
connects to 68-pin E Series, S Series, and B Series devices. If you need
a right-angle connector, the SH68-68R1-EP shielded cable is
electrically equivalent.
1 m ........................................................................................184749-01
2 m ........................................................................................184749-02
Please call for other length options.
two 68-pin connectors. Use this cable to connect a 68-pin
E Series, S Series (except NI 6143), or B Series multifunction DAQ
device to 68-pin accessories.
1 m ........................................................................................182482-01
RC68-68 – A 68 conductor ribbon cable that connects a DAQCard,
an M Series device, or an NI 6143 directly to 68-pin accessories. Two
RC68-68 cables can be used together in adjacent PCMCIA slots or
adjacent connectors on 2-connector M Series devices.
0.25 m................................................................................187252-0R25
1 m ........................................................................................187252-01
R1005050 – Connects 100-pin E Series devices, to standard 50-pin
third-party or custom connectors.
1 m ........................................................................................182762-01
2 m ........................................................................................182762-02
R6850 – Combines a 68F-50M cable adapter and a standard 50-pin
cable with female connectors on both ends. It is designed to adapt a
68-pin E Series, S Series, or B Series multifunction DAQ device to a
third-party or custom 50-pin accessory.
1 m ........................................................................................776842-01
Shielded I/O Cables
SHC68-68-EPM – A high-performance shielded 68-conductor
cable terminated with a VHDCI 68-pin male connector at one end
and a 68-pin female 0.050 D-type connector at the other end for
connecting M Series DAQ devices to standard 68-pin accessories.
0.5 m....................................................................................192061-0R5
1 m ......................................................................................192061-01
2 m ......................................................................................192061-02
SHC68-68 – A low-cost cable for connecting M Series DAQ devices
to 68-pin accessories and signal conditioning systems. It features
individually twisted cable pairs, but does not have shields between
the analog and digital signals. For improved noise rejection, consider
the SHC68-68-EPM.
1 m ........................................................................................191945-01
2 m ........................................................................................191945-02
R6868
RC68-68
SH68-68R1-EP
SH68-68R1-EP – A shielded 68-conductor cable for use with
68-pin E Series, S Series (except NI 6143), and B Series devices. One
end terminates with a 68-pin female 0.050 series D-type connector
and the other end terminates with a right-angle 68-pin female 0.050
series D-type connector.
1 m ........................................................................................187051-01
SH100100 – A shielded 100-conductor cable terminated with
100-pin male 0.050 series D-type connectors. This cable connects the
100-pin E Series devices to 100-pin accessories.
1 m ........................................................................................182853-01
2 m ........................................................................................182853-02
SH1006868 – A shielded cable that connects to 100-pin E Series
devices and terminates with two female 68-pin 0.050 series
D-type connectors.
1 m ........................................................................................182849-01
2 m ........................................................................................182849-02
SHC68-68-EP and SHC68U-68-EP – Shielded 68-conductor
cables terminated with a VHDCI 68-pin male connector at one end and
a 68-pin female 0.050 series D-type connector at the other. When using
two E Series DAQCards in adjacent slots, use one SHC68-68-EP and
one SHC68U-68-EP.
SHC68-68-EP
0.5 m ..............................................................................186838-0R5
1 m ....................................................................................186838-01
SHC68U-68-EP
0.5 m ..............................................................................187406-0R5
1 m ....................................................................................187406-01
SH100100
SH1006868
SHC68-68-EP and
SHC68U-68-EP
3
Multifunction DAQ Accessories and Cables
SH6850 – A shielded cable that connects a 68-pin E Series, S Series
(except NI 6143), or B Series multifunction DAQ product to a third
party or custom standard 50-pin accessory. The cable provides a
screw-latching 68-pin female connector on one side and a standard
50-pin female connector on the other side.
1 m ........................................................................................776784-01
2 m ........................................................................................776784-02
68M-50F – Adapter that connects a 68-pin NI shielded cable to a
standard 0.1 by 0.1 in. 50-pin connector on third-party or custom
accessories. Use the 68M-50F MIO with the SHC68-68-EPM,
SH68-68-EP, SHC68-68-EP, SHC68U-68-EP, or the multifunction
I/O portion of the SH1006868. Use The 68M-50F Extended I/O cable
adapter for the extended I/O portion of the SH1006868.
68M-50F MIO ......................................................................184670-01
Connector Blocks
BNC-2100 Series – Shielded connector blocks with signal-labeled
BNC connectors for easy connectivity of your I/O signals. The
BNC-2110 and BNC-2120 work with all E Series, M Series, S Series,
and B Series multifunction DAQ or analog output devices. The
BNC-2120 also provides a function generator, quadrature encoder,
temperature reference, thermocouple connector, and LED so that you
can test the functionality of your hardware. The BNC-2115 has 24
BNC inputs for connecting to the extended I/O channels of 100-pin
E Series DAQ devices.
BNC-2110 ..............................................................................777643-01
Dimensions – 20.3 by 11.2 by 5.5 cm (8.0 by 4.4 by 2.2 in.)
BNC-2115 ..............................................................................777807-01
Dimensions – 20.3 by 11.2 by 5.5 cm (8.0 by 4.4 by 2.2 in.)
BNC-2120 ..............................................................................777960-01
Dimensions – 26.7 by 11.2 by 6.0 cm (10.5 by 4.4 by 2.4 in.)
RTSI Bus Cables
– Connect timing and synchronization
signals among data acquisition, M Series, E Series, S Series, vision,
motion, and CAN boards for PCI. For systems using long and short
boards, order the extended RTSI cable.
2 boards ................................................................................776249-02
3 boards .................................................................................776249-03
4 boards .................................................................................776249-04
5 boards ................................................................................776249-05
Extended, 5 boards................................................................777562-05
BNC-2090 – A shielded, rack-mountable adapter with 22 signallabeled BNC connectors and 28 spring terminal blocks to simplify
connections to your I/O signals. The BNC-2090 includes component
locations for passive signal conditioning and connects to any 68-pin
M Series, S Series, E Series, or B Series DAQ device.
BNC-2090 ..............................................................................777270-01
Dimensions – 48.3 by 4.4 by 18.8 cm (19.0 by 1.7 by 7.4 in)
SC-2075 – Connector block with breadboard area for
Signal Conditioning
SCC – A portable modular signal conditioning system consisting of
modules that plug into a low-profile shielded carrier. Choose from a
variety of signal conditioning options including sensor, input,
isolation, and filtering modules. SCC is compatible with M Series,
E Series, and some B Series and portable devices.
SCC Signal Conditioning..................................................See page 168
prototyping, as well as BNC and spring terminal connectivity for
68-pin M Series, E Series, and B Series multifunction DAQ devices.
The built-in ±15 V or adjustable 0 to 5 V power supply and LEDs for
digital lines make the SC-2075, ideal for academic laboratories.
SC-2075 ................................................................................778147-90
Dimensions – 26.7 by 20.7 by 4.4 cm (10.5 by 8.2 by 1.7 in.)
TBX-68 – Connector block for easy connection of field
SCXI – A high-performance modular signal conditioning platform
that provides a front end to your M Series or E Series
DAQ device. You can expand your analog inputs to 3,072 channels.
SCXI offers a variety of modules for sensor conditioning,
amplification, filtering, and other modules.
SCXI Signal Conditioning ................................................See page 183
68M-50F
4
RTSI Bus Cable
I/O signals to 68-pin M Series, E Series, S Series, and B Series
DAQ devices. The TBX-68 includes 68 screw terminals and one
68-pin male connector for direct connection to 68-pin cables. The
TBX-68 is mounted in a protective plastic base with hardware for
mounting on a standard DIN rail.
TBX-68 ..................................................................................777141-01
Dimensions – 12.50 by 10.74 cm (4.92 by 4.23 in.)
SCC Portable, Modular
SCXI High-Performance
Signal Conditioning
Signal Conditioning
BNC-2100 Series
BNC-2090
SC-2075
Multifunction DAQ Accessories and Cables
CA-1000 – A configurable enclosure that gives you maximum
DAQ Signal Accessory – For demonstration of analog, digital,
user-defined connectivity and flexibility through customized
panelettes. Each enclosure can accommodate up to nine panelettes.
CA-1000 ............................................................................See page 222
Dimensions – 30.7 by 25.4 by 4.3 cm (21.1 by 10 by 1.7 in.
and counter/timer functions of DAQ devices. You can use the DAQ
Signal Accessory with any 68-pin M Series, E Series, or B Series DAQ
device. It features a built-in function generator, quadrature encoder,
solid-state relay, IC temperature sensor, noise generator, microphone
jack, thermocouple jack, four LEDs, and a digital trigger button.
DAQ Signal Accessory ..........................................................777382-01
Dimensions – 12.7 by 12.7 cm (5.0 by 5.0 in.)
TB-2705 – Terminal block for 68-pin devices. It latches to the front
of your PXI E Series or S Series DAQ module with locking screws and
provides strain relief and easy access to your I/O signals through
screw terminals.
TB-2705 ................................................................................778241-01
Dimensions – 8.43 by 10.41 by 2.03 cm (3.32 by 4.1 by 0.8 in.)
SCB-68 and SCB-100 – Shielded I/O connector blocks for
rugged, low-noise signal termination with M Series, E Series,
S Series, or B Series DAQ devices. They include general-purpose
breadboard areas and an IC temperature sensor for cold-junction
compensation in temperature measurements.
SCB-68 (for M Series, 68-pin E Series,
S Series, or B Series) ..............................................................776844-01
Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)
SCB-100 (for 100-pin E Series)............................................776990-01
Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)
CB-68LP and CB-68LPR – Low-cost termination accessories with
68 screw terminals for easy connection of I/O signals to 68-pin
M Series, E Series, S Series, or B Series multifunction DAQ devices.
They include one 68-pin male connector for direct connection to
68-pin cables and standoffs for use on a desktop or for mounting in
a custom panel. The CB-68LP has a vertical-mounted 68-pin
connector. The CB-68LPR has a right-angle mounted connector, and
can be used with the CA-1000 (see page 222).
CB-68LP ................................................................................777145-01
Dimensions – 14.35 by 10.74 cm (5.65 by 4.23 in.)
CB-68LPR ............................................................................777145-02
Dimensions – 7.62 by 16.19 cm (3.00 by 6.36 in.)
CA-1000
TB-2705
SCB-68 and SCB-100
Custom Connectivity Components
68-Pin Custom Cable Connector/Backshell Kit – A 68-pin kit
used to make custom cables. Solder-cup contacts are available for
soldering cable wires to the connector.
68-pin connector/backshell kit ............................................776832-01
PCB Mounting Connectors for Custom Accessories – Build
custom accessories that connect to 68-conductor or 100-conductor
shielded and ribbon cables using these connectors.
Two connectors are available, one for right-angle and one for vertical
mounting onto a PCB.
68-pin, male, right-angle mounting ....................................777600-01
68-pin, male, vertical mounting ..........................................777601-01
100-pin, female, right-angle mounting................................777778-01
100-pin, female, vertical mounting......................................777779-01
Strain-Relief Accessory – Attaches to the bottom of your
notebook computer or DAQPad and provides adjustable strain relief
for one or two PCMCIA cables attached to DAQCards, or a USB
cable attached to a DAQPad device.
Strain-relief accessory ..........................................................777550-01
CB-68LP and CB-68LPR
DAQ Signal Accessory
Strain-Relief Accessory
© 2005 National Instruments Corporation. All rights reserved. ni.com is a trademarks of National Instruments.
Other product and company names listed are trademarks or trade names of their respective companies.
2005_4968_301_101_D
5