T2
Pocket Reference
Cards
Stryker Nailing
®
Tibial Nails
Femoral Nails
Humeral Nails
Arthrodesis Nails
T2
Flexible Nails
General Notes
The following notes apply to all T2 IM Nails (except T2 Kids) unless
separately delineated either below or on the Important Facts page for each
nail. Read carefully for tips, pointers, and other facts.
1. All screw hole dimensions reference the center point of the screw.
2. Internal compression screws require a 5.0mm partially threaded screw in
the oblong hole.
3. T2 8mm Nails require the use of 4mm fully threaded locking screws
(distally) and 5mm (proximally).
4. T2 A/R Humeral nails require ALL 4mm locking screws.
5. T2 nails may ALL require additional reaming for the proximal
(driving section) beyond 1 to 1.5mm larger than the nail diameter.
6. T2 GTN - 8, 14 & 15mm nails are special order.
T2 Tibia Nail
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Tibia Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18 mm)a
Disposables - Sterile:
Qty
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 800 Ball Tip Guide Wireb
Bixcut Mod Trinkle Shaft, 448mmc
4.2 x 340 Drill Bit (Proximal Guided)d
4.2 x 130 Drill Bit (Distal Freehand)b
Cat No.
1806-0050S
1806-0080S
0227-3000S
1806-4260S
1806-4280S
For Internal Compression - Partially threaded screw is required in oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
5.0 x 230 Drill Bit d
Cat No.
1806-5000S
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. 8mm diameter Tibia nail requires the following:
• (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S for 4mm distal screws
• (1) 3 x 800 Smooth Tip Guide Wire – Cat No: 1806-0090S
• (1) Teflon Exchange Tube – Cat No: 1806-0073S
c. Optional: Bixcut Mod Trinkle Shaft, 510mm - Cat No: 0227-8510S
Bixcut with AO shaft, 448mm – Cat No: 0226-3000S
3 x 1000 Ball Tip Guide Wire - Cat No: 1806-0085S
d. Optional: If utilizing the short Tissue Protection and Drill Sleeve,
the 4.2 x 260mm Drill Bit (1806-4250S) and 5.0 x 180mm Drill Bit
(1806-5010S) may be utilized.
Impor tant Facts
Shaft Diameter:
8, 9, 10, 11, 12, 13, 14, 15mm
Driving End
17
24
Driving End Diameter:
11.5mm for shaft diameters ≤ 11mm
Same as shaft diameter for all other sizes
Length:
240 to 420mm (15mm increments)
Reaming:
1 to 1.5mm larger than the nail diameter
0mm
10 ° A / P
slope
34
41
Compression
Range 7mm
Herzog Bend, 10°
image of standard nail
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
5.0mm fully threaded
4.0mm fully threaded for 8mm
diameter nail only
No Bow
Screw Hex Size:
3.5mm
End Caps:
Fully threaded, Standard,
+5, +10, +15, +20, +25, +30, +35mm
(Only the fully threaded end cap locks
proximal screw hole)
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
Compression Screw:
Advanced (8mm metric thread)
50
60mm
Distal Bend, 4 °
25
15
5
0mm
T2 Femoral Nail (Antegrade Mode)
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Femoral Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18mm)a
Disposables - Sterile:
Qty
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 1000 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mmb
4.2 x 340 Drill Bit (Proximal Guided)
4.2 x 180 Drill Bit (Distal Freehand)
Cat No.
1806-0050S
1806-0085S
0227-3000S
1806-4260S
1806-4270S
For Internal Compression - Partially threaded screw is required for oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
5.0 x 230 Drill Bit
Cat No.
1806-5000S
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm - Cat No. 0226-3000S
8mm diameter T2 Femoral nails requires the following:
• (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S for 4mm distal screws
• (1) 3 x 800 Smooth Tip Guide Wire – Cat No: 1806-0090S
• (1) Teflon Exchange Tube – Cat No: 1806-0073S
Impor tant Facts
(Antegrade Mode)
Driving End
Shaft Diameter:
9, 10, 11, 12, 13, 14, 15mm
(8mm diameter require special order)
0mm
Driving End Diameter:
11.5mm for shaft diameters ≤ 11mm
Same as shaft diameter for all other sizes
35
45
Length:
140 to 480mm (20mm increments)
length 240-480mm for R1.5
Compression
range 10mm
60
Reaming:
1 to 1.5mm larger than the nail diameter
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
5.0mm fully threaded
R=3.0 or 1.5m
Screw Hex Size:
3.5mm
End Caps:
Standard, +5, +10, +15, +20, +25,+30, +35mm
Internal Diameter:
Shaft - 5.0mm
Driving End - 8mm metric thread
Compression Screw:
Advanced, Standard
+5, +10, +15mm
(all sizes are 8mm metric thread)
50
25
0mm
T2 Femoral Nail (Retrograde Mode)
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Femoral Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18mm)a
Disposables - Sterile:
Qty
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 1000 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mmb
4.2 x 340 Drill Bit (Distal Guided)
4.2 x 230 Drill Bit (Proximal Freehand)
Cat No.
1806-0050S
1806-0085S
0227-3000S
1806-4260S
1806-4290S
Optional: Condyle Screws
Qty
1
1
Description
1.8 x 310 Condyle Screw K-Wire
5.0 x 340 Drill Bit
Cat No.
0152-0218S
1806-5020S
For Internal Compression - Partially threaded screw is required for oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
5.0 x 230 Drill Bit
Cat No.
1806-5000S
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm – Cat No: 0226-3000S
8mm diameter Femoral nails requires the following:
• (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S for 4mm distal screws
• (1) 3 x 800 Smooth Tip Guide Wire – Cat No: 1806-0090S
• (1) Teflon Exchange Tube – Cat No: 1806-0073S
Impor tant Facts
(Retrograde Mode)
Shaft Diameter:
9, 10, 11, 12, 13, 14, 15mm
(8mm diameter require special order)
0mm
15
25
35
40
Driving End Diameter:
11.5mm for shaft diameters ≤ 11mm
Same as shaft diameter for all other sizes
50
Length:
140 to 480mm (20mm increments)
length 240-480mm for R1.5
Reaming:
1 to 1.5mm larger than the nail diameter
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
5.0mm fully threaded1
5.0mm condyle screws
R=3.0 or 1.5m
Screw Hex Size:
3.5mm for fully and partially threaded
6.3mm for condyle screws and nuts
End Caps:
Standard, +5, +10, +15, +20, +25,+30, +35mm
(All sizes lock screw in most distal hole)
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
60
45
Compression
range 10mm
35
15
Compression Screw:
Advanced
(8mm metric thread)
0mm
Driving End
T2 GTN
Instruments:
• T2 Basic Long Tray
• GTN Indication Tray
• Bixcut Modular Head Reamer Kit
(Diameter 9 to 18mm)
Disposables - Sterile:
Qty
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 1000 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mm
4.2 x 340 Drill Bit (Proximal Guided)
4.2 x 180 Drill Bit (Distal Freehand)b
Cat No.
1806-0050S
1806-0085S
0227-3000S
1806-4260S
1806-4270S
For Internal Compression - Partially threaded screw is required for oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
5.0 x 230 Drill Bit
Notes:
a. Optional: Bixcut with AO Shaft, 448mm - Cat. No: 0226-3000S
b. 8mm diameter T2 GTN Nails can only be locked with 4mm
Fully threaded screws at non-driving end
Use the Ø3.5 x 180mm Drill (1806-3570S) for freehand locking
Cat No.
1806-5000S
Important Facts
Driving End
Type:
Left & Right
Shaft Diameter:
8, 9, 10, 11, 12, 13, 14, 15mm
Driving End Diameter:
11.5mm for shaft diameters ≤ 11mm
Same as shaft diameter for all other sizes
Length:
240 to 480mm (20mm increments)
0mm
26.6mm
Compression
Range 10mm
45mm
55mm
69.5mm
Reaming:
1 to 1.5mm larger than the nail diameter
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
5.0mm fully threaded
Screw Hex Size:
3.5mm for all
End Caps GTN:
Standard, +5, +10, +15mm
4° Valgus Bend
R=1.5m
End Caps T2:
Standard, +5, +10, +15mm
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
Canulated Compression Screw:
Standard (8mm metric thread)
43mm
GTN End-Caps cannot be used
with internal compression screw
T2 End-Caps used with
cannulated compression screw
8mm
0mm
T2 Supracondylar Nail (SCN)
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 SCN Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18mm)a
Disposables - Sterile:
Qty
1
1
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 1000 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mm
4.2 x 340 Drill Bit (Distal & Proximal Guided)
4.2 x 230 Drill Bit (Proximal Freehand)
1.8 x 310 Condyle Screw K-Wire
5.0 x 340 Drill Bit (For Condyle Screw)
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm - Cat No: 0226-3000S
Cat No.
1806-0050S
1806-0085S
0227-3000S
1806-4260S
1806-4290S
0152-0218S
1806-5020S
Important Facts
0mm
Shaft Diameter:
9, 10, 11, 12, 13, 14mm
15
20
Driving End Diameter:
11.5mm for shaft diameters ≤ 11mm
Same as shaft diameter for all other sizes
40
Length:
Short Nail – 170 & 200mm
Long Nail – 240 to 440mm
(20mm increments)
Reaming:
1 to 1.5mm larger than the nail diameter
R=2m
Long Nail Only
Short Nail
has No Bow
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
5.0mm fully threaded
5.0mm condyle screws
Screw Hex Size:
3.5mm for fully threaded
6.3mm for condyle screws and nuts
End Caps:
Standard (locks most distal screw)
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
42
(4° A/P bend)
32
21
14
6
0mm
Hole reference dimensions are the
same for the Long and Short nails.
Driving End
T2 Recon Nail (Antegrade Mode)
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Recon Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18 mm)a
Disposables - Sterile:
Qty
1
1
1
1
1
1
Description
3.2 x 400 Recon K-Wire (Entry)
3 x 1000 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mmb
4.2 x 250 Drill Bit (Proximal Guided First Cortex)
4.2 x 340 Drill Bit (Proximal Guided)
4.2 x 180 Drill Bit (Distal Freehand)
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm – Cat No: 0226-3000S
Cat No.
1806-3031S
1806-0085S
0227-3000S
1806-8018S
1806-4260S
1806-4270S
Important Facts
(Antegrade Mode)
Type:
Left & Right
Driving End
Set Screw, Antegrade
Shaft Diameter:
R2.0: 9, 11, 13, 15
R1.5: 9, 10, 11, 12, 13, 15
Driving End Diameter:
13mm for shaft diameters 9-12mm
15mm for shaft diameters 13 & 15mm
Length:
R2.0: 280 to 480mm
R1.5: 260 to 480mm
(20 mm increments)
0mm
70°
44
7°
retroversion
75
4° Valgus Bend
Reaming:
1.5 to 2.0mm larger than the nail diameter
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
5.0mm fully threaded
R= 2.0 or 1.5m
Screw Hex Size:
3.5mm for all
Set Screw:
8.0mm metric thread
(Locks oblique screw)
End Caps:
Standard, +5, +10, +15mm
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
40
20
15
0mm
T2 Recon Nail (Recon Mode)
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Recon Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18 mm)a
Disposables - Sterile:
Qty
2
1
1
1
1
Description
3.2 x 400 Recon K-Wire (Entry & Lag Screws)
3 x 1000 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mmb
Solid Step Drill (Lag Screws)
4.2 x 180 Drill Bit (Distal Freehand)
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: Bixcut with AO shaft, 448mm – Cat No: 0226-3000S
Cat No.
1806-3031S
1806-0085S
0227-3000S
1806-3026S
1806-4270S
Important Facts
(Recon Mode)
Driving End
Type:
Left & Right
Shaft Diameter:
R2.0: 9, 11, 13, 15
R1.5: 9, 10, 11, 12, 13, 15
Driving End Diameter:
13mm for shaft diameters 9-12mm
15mm for shaft diameters 13 & 15mm
Length:
R2.0: 280 to 480mm
R1.5: 260 to 480mm
(20 mm increments)
Set Screw, Recon
10° Anteversion
0mm
26
125° CCD
10.5
17
75
4° Valgus Bend
Reaming:
1.5 to 2.0mm larger than the nail diameter
Proximal Screw Size:
6.5mm Lag Screws
Distal Screw Size:
5.0mm fully threaded
Screw Hex Size:
3.5mm for fully threaded screws
5.0mm for Lag Screws
2.0 or 1.5m
Set Screw:
8.0mm metric thread
(locks most proximal lag screw)
End Caps:
Standard, +5, +10, +15mm
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
40
20
15
0mm
T2 Humeral Nail (Antegrade & Retrograde)
Required Instruments
Instruments:
• T2 Basic Short Tray
• T2 Humeral Tray
• Full Bixcut Kit (diameter 6 to 22mm)
Disposables - Sterile:
Qty
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
2.5 x 800 Ball Tip Guide Wire
Teflon Exchange Tubea
2.2 x 800 Smooth Tip Guide Wire
3.5 x 230 Drill Bit (Proximal & Distal)b
Cat No.
1806-0050S
1806-0083S
1806-0073S
1806-0093S
1806-3540S
For Internal Compression - Partially threaded screw is required for oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
4.0 x 180 Drill Bit
Notes:
a. With T2 PHN / HUM
b. Optional: Drill for freehand locking:
• (1) 3.5 x 130 Drill Bit – Cat No: 1806-3550S
Cat No.
1806-4000S
Impor tant Facts
Driving End
Shaft Diameter:
7, 8, 9mm
Driving End Diameter:
8mm for 7mm shaft diameter
Same as shaft diameter for all other sizes
Length:
140 to 180mm (20mm increments)
190 to 320mm (10mm increments)
0mm
12
23
Compression
Range 6mm
Reaming:
1 to 1.5mm larger than the nail diameter
30
36
62
Bend, 6°
Proximal/Distal Screw Size:
4.0mm fully threaded1
Screw Hex Size:
3.5mm for all
2.5mm for commpression screw only
No Bow
End Caps:
Standard, +5, +10, +15, +20, +25mm
(all sizes lock screw in hole closest to driving end)
Internal Diameter:
Shaft - 2.65mm
Driving end - 6mm metric thread
Compression Screw:
Advanced
(6mm metric thread)
Bend, 4°
48
28
18
10
0mm
T2 Proximal Humeral Nail (PHN)
Required Instruments
Instruments:
• T2 Basic Short Tray
• T2 PHN Tray
• Full Bixcut Kit
Disposables - Sterile:
Qty
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
2.5 x 800 Ball Tip Guide Wire
Teflon Exchange Tube
2.2 x 800 Smooth Tip Guide Wire
3.5 x 130 Drill Bit (Distal free-hand)b
Cat No.
1806-0050S
1806-0083S
1806-0073S
1806-0093S
1806-3550S
Optional: Drills for Proximal screws in case of dense bone.
Drill Near Cortex Only
Qty
1
Description
5.0 x 180 Drill Bit (Proximal)
Notes:
a. Distal guided drill only for short nail
b. Use with long nail only
Cat No.
1806-5010S
Impor tant Facts
Type:
Left & Right
Driving End
Long Nail
Short Nail
0mm
10°
Shaft Diameter:
8mm
9.5
17
23
Driving End Diameter:
10mm
9°
Length:
Short Nail: 150mm
Long Nail: 220 to 300mm
(20mm increments)
Bend,
6°
29.5
62
80
Reaming:
1-1.5mm larger than the diameter of nails
95
101
Proximal Screw Size:
5.0mm fully threaded
Distal Screw Size:
4.0mm fully threaded
Screw Hex Size:
3.5mm for all
No Bow
Long & Short Nail
End Caps:
Standard, +2 +4mm
(all sizes lock screw in most
proximal hole)
Internal Diameter:
Shaft - 2.65mm
Driving end - 6mm metric thread
36
28.5
21
13.5
7.5
0mm
T2 Knee Arthrodesis Nail
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Femoral Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18mm)
Disposables - Sterile:
Qty
1
2
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 1250 Ball Tip Guide Wireb
Bixcut Mod Trinkle Shaft, 885mmb
4.2 x 340 Drill Bit (Proximal)
4.2 x 180 Drill Bit (Distal)
Cat No.
1806-0050S
1806-1250S
0227-8885S
1806-4260S
1806-4270S
For Internal Compression - Partially threaded screw is required for oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
5.0 x 230 Drill Bit
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. Optional: For separate reaming of Tibia and Femur use:
Tibia: 3 x 800 Ball Tip Guide Wire – Cat No: 1806-0080S
Femur: 3 x 1000 Ball Tip Guide Wire – Cat No: 1806-0085S
Bixcut Mod Trinkle Shaft, 448mm – Cat No: 0227-3000S
Optional: Bixcut with AO shaft, 448mm - Cat No: 0226-3000S
Cat No.
1806-5000S
Impor tant Facts
Driving End
Type:
Left & Right
Shaft Diameter:
10, 11.5, and 13mm
0mm
35
Compression
range 10mm
45
Driving End Diameter:
Same as shaft diameter
60
Length:
540 to 780mm (40mm increments)
Reaming:
1.5 to 2.0mm larger than the
diameter of the nail
Proximal Screw Size:
5.0mm fully threaded1
Distal Screw Size:
5.0mm fully threaded
R=3m
Screw Hex Size:
3.5mm for all
End Caps:
Standard, +5, +10, +15, +20, +25, +30, +35mm
(does not lock most proximal screw)
5° Bend (Valgus)
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
Compression Screw:
Standard, only 8mm compression screw
(Cat. No: 1825-0000S)
(all sizes have 8mm metric thread)
75
35
25
0mm
Do not use the most proximal
hole on the Targeting device.
T2 Ankle Arthrodesis Nail
Required Instruments
Instruments:
• T2 Basic Long Tray
• T2 Ankle Tray
• Bixcut Modular Head Reamer Kit
(diameter 9 to 18mm)
Disposables - Sterile:
Qty
1
1
1
1
1
1
1
Description
3 x 285 K-Wire (Entry)
3 x 800 Ball Tip Guide Wire
Bixcut Mod Trinkle Shaft, 448mmc
Teflon Exchange Tube
3 x 800 Smooth Tip Guide Wire
4.2 x 340 Drill Bit
4.2 x 250 Drill Bit (Proximal Guided)b
Cat No.
1806-0050S
1806-0080S
0227-3000S
1806-0073S
1806-0090S
1806-4260S
1806-8018S
For Internal Compression - Partially threaded screw is required for oblong hole.
- Overdrill near cortex only with the drill below.
Qty
1
Description
5.0 x 230 Drill Bit
Notes:
a. Optional: Full Bixcut Kit (diameter 6 to 22mm)
b. For 300mm nail proximal free hand locking is required
Use: 4.2 x 130 Drill Bit – Cat No: 1806-4280S
c. Optional: Bixcut with AO Shaft, 448mm – Cat. No: 0226-3000S
Cat No.
1806-5000S
Important Facts
Type:
Left & Right
0mm
Shaft Diameter:
10, 11, and 12mm
15
20
Driving End Diameter:
12mm for all shaft diameters
40
Length:
150, 200 and 300mm
Reaming:
1 to 1.5mm larger than the diameter of the nail
Proximal Screw Size:
5.0mm fully threaded
No Bow
Distal Screw Size:
5.0mm fully threaded1
Internal
Compression
Range 5mm
Screw Hex Size:
3.5mm for all
End Caps:
Standard, +5, +10, +15mm
(All sizes lock screw in most distal hole)
47
5° valgus
bend
Internal Diameter:
Shaft - 5.0mm
Driving end - 8mm metric thread
Compression Screw:
8mm metric thread, cannulated2
(Cat. No: 1818-0001S)
Must be pre-loaded into nail prior to insertion
Ball tip Guide wire does not pass
through compression screw
19.5
7.5
0 mm
Driving End
Distal hole is
10° P/M to A/L
T2 Kids Flexible Nail
Instruments:
T2 Kids Basic
Nail Tip
Outer
curve
(convex)
Materials
The T2 Flexible Nail is offered in
two materials:
Titanium:
Ti6Al4V Type II anodized with
laser-etched bands for easy nail
diameter identification
Diameters:
Ø2.5; Ø3.0; Ø3.5; Ø4.0mm
with length 450mm
Ø Nail = 0.4 x ØIM Canal
(with some individual adaptations tolerated).
It can be bent back with
the bending instrument,
if required.
ø Nail (d)
Diameters
Diameters:
Ø1.5; Ø1.75; Ø2.0; Ø2.25mm
with length 300mm
Pre-curved
shaft portion
øNail = øIM canal x 0.4
Tip
Stainless Steel:
1.4441 (316LVM) with laser etched bands
for easy nail diameter identification
Inner Curve Tapered
(concave)
extremity
Curved Nail tip or
nail tip curvature
Tip
= 2.2
øNail
R = 4 x Nail ø
T2 Kids Optional Instrument Set
available separately.
Nail end (Driving end)
325 Corporate Drive
Mahwah, NJ 07430
t: 201 831 5000
www.stryker.com
A surgeon must always rely on his or her own professional clinical judgment when
deciding whether to use a particular product when treating a particular patient.
Stryker does not dispense medical advice and recommends that surgeons be trained
in the use of any particular product before using it in surgery. The information
presented is intended to demonstrate the breadth of Stryker product offerings.
A surgeon must always refer to the package insert, product label and/or instructions
for use before using any Stryker product. Products may not be available in all
markets because product availability is subject to the regulatory and/or medical
practices in individual markets. Please contact your Stryker representative if you
have questions about the availability of Stryker products in your area.
Stryker Corporation or its divisions or other corporate affiliated entities own,
use or have applied for the following trademarks or service marks: Stryker, T2.
All other trademarks are trademarks of their respective owners or holders.
T2-BR-1 Rev. 1 06-2014
Copyright © 2014