SECTION 10 14 00
SIGNAGE
PART 1
1.01
GENERAL
REFERENCES
A.
The following is a list of standards that may be referenced in this section:
1.
2.
3.
4.
5.
6.
7.
1.02
American Society of Mechanical Engineers (ASME): A13.1, Scheme
for the Identification of Piping Systems.
ASTM International (ASTM):
a.
A53/A53M, Standard Specification for Pipe, Steel, Black and
Hot-Dipped, Zinc-Coated Welded and Seamless.
b.
D709, Standard Specification for Laminated Thermosetting
Materials.
The Chlorine Institute, Inc.: WC-1, Wall Chart: Handling Chlorine
Cylinders and Ton Containers.
International Code Council (ICC):
a.
A117.1, Accessible and Usable Buildings and Facilities.
b.
International Fire Code (IFC): Chapter 27, Hazardous
Materials-General Provisions.
National Fire Protection Association (NFPA):
a.
704, Standard System for the Identification of the Hazards of
Materials for Emergency Response.
b.
HAZ-01, Fire Protection Guide to Hazardous Materials.
Occupational Safety and Health Act (OSHA).
U.S. Department of Transportation, Federal Highway Administration:
Manual on Uniform Traffic Control Devices for Streets and Highways.
SUBMITTALS
A.
Action Submittals:
1.
B.
Shop Drawings:
a.
Drawings showing layouts, actual letter sizes and styles, and
Project-specific mounting details.
b.
Manufacturer’s literature showing letter sizes and styles, sign
materials, and standard mounting details.
Informational Submittals: Manufacturer’s installation instructions.
PW/DEN001/650394
SEPTEMBER 17, 2015
©COPYRIGHT 2015 CH2M HILL
SIGNAGE
10 14 00 - 1
PART 2
2.01
PRODUCTS
SIGNS
A.
Metal Sign (Type B):
1.
2.
B.
Fiberglass Sign (Type C):
1.
2.
C.
Material: Three-ply laminated fiberglass, minimum 1/8 inch thick, with
contrasting color core message layer between two clear weatherresistant surface layers.
Manufacturers:
a.
Best Manufacturing Co.
b.
Brady Signmark.
Exit Sign (Type G):
1.
2.
3.
2.02
Material: Baked enamel finished 20-gauge (minimum) steel or 18-gauge
(minimum) aluminum signs.
Manufacturers:
a.
Seton Identification Products.
b.
Nutheme Illustrated Safety Co.
Material: Plastic, 1/8 inch minimum thickness.
Letters:
a.
6 inches high, with 3/4-inch stroke.
b.
2 inches wide, except for letter “I”, with spacing of 3/8 inch.
Colors: Red letters and direction arrows on white background.
IDENTIFICATION LABELS
A.
Pipe Labels:
1.
2.
3.
4.
5.
6.
7.
8.
SIGNAGE
10 14 00 - 2
Snap-on, reversible type with lettering and directional arrows, sized for
outside diameter of pipe and insulation.
Provided with ties or straps for pipes of 6 inches and over diameter.
Designed to firmly grip pipe so labels remain fixed in vertical pipe runs.
Material: Heavy-duty vinyl or polyester, suitable for exterior use, long
lasting, and resistance to moisture, grease, and oils.
Letters and Arrows: Black on OSHA safety yellow background.
Color Field and Letter Height: Meet ASME A13.1.
Message: Piping system name as indicated on Piping Schedule.
Manufacturers and Products:
a.
Brady Signmark; B-915 BradySnap-On and Strap-On Pipe
Markers.
b.
Seton Identification Products; Ultra-mark Pipe Markers.
PW/DEN001/650394
SEPTEMBER 17, 2015
©COPYRIGHT 2015 CH2M HILL
B.
Equipment Labels:
1.
2.
3.
4.
5.
6.
7.
8.
2.03
ANCILLARY MATERIALS
A.
Fasteners: Stainless steel screws or bolts of appropriate sizes.
B.
Manufacturer’s standard brackets for wall mounting of two-sided exit signs.
PART 3
3.01
3.02
Applies to equipment with assigned tag numbers, where specified.
Letters: White engraved, 3/4 inch minimum high.
Background: Black.
Materials: Multi-layered acrylic.
Furnish 1-inch margin with holes at each end of label, for mounting.
Size:
a.
2 inches minimum and 3 inches maximum high, by 14 inches
minimum and 18 inches maximum long.
b.
Furnish same size base dimensions for all labels.
Message: Equipment names and tag numbers as used in sections where
equipment is specified.
Manufacturers:
a.
Brady Signmark.
b.
Seton Identification Products.
EXECUTION
INSTALLATION—GENERAL
A.
In accordance with manufacturer’s recommendations.
B.
Mount securely, plumb, and level.
SIGNS
A.
General:
1.
2.
B.
Fasten to walls or posts, or hang as scheduled.
Anchor in place for easy removal and reinstallation with ordinary hand
tools.
Information, Exit, and Safety Signs:
1.
2.
Install facing traffic. Locate for high visibility with minimum restriction
of working area around walkways and equipment.
Install as scheduled.
PW/DEN001/650394
SEPTEMBER 17, 2015
©COPYRIGHT 2015 CH2M HILL
SIGNAGE
10 14 00 - 3
3.03
IDENTIFICATION LABELS
A.
Pipe Labels:
1.
2.
3.
4.
5.
6.
B.
Equipment Labels:
1.
2.
3.04
Locate at connections to equipment, valves, or branching fittings at wall
boundaries.
At intervals along piping not greater than 18 feet on center with at least
one label applied to each exposed horizontal and vertical run of pipe.
At exposed piping not normally in view, such as above suspended
ceilings and in closets and cabinets.
Supplementary Labels: Provide to Owner those listed on Piping
Schedule that do not receive arrows.
Apply to pipe after painting in vicinity is complete, or as approved by
Engineer.
Install in accordance with manufacturer’s instructions.
Locate and install on equipment or concrete equipment base.
Anchor to equipment or base for easy removal and replacement with
ordinary hand tools.
SUPPLEMENT
A.
The supplement listed below, following “End of Section,” is a part of this
specification.
1.
Sign Schedule: Tabulation of characteristics and mounting information
for each sign on Project. Provide items as scheduled. Meet requirements
of Occupational Safety and Health Act (OSHA).
END OF SECTION
SIGNAGE
10 14 00 - 4
PW/DEN001/650394
SEPTEMBER 17, 2015
©COPYRIGHT 2015 CH2M HILL
Sign Schedule
Sign
Size
No.1
Type2
Format3
Width
Height
Lettering
Mounting
Color
Location
Method
Height
to Top
Height
Style
Color
Message
Faces
Other
Requirements
C-1
C
1014-002
20"
14"
Yellow
Hanging
Chain
5'-6"
1" min.
Helvetica Black CAUTION
Equipment Starts
Automatically
1
2 - in room 200201 & 200-101
C-2
C
1014-002
20"
14"
Yellow
Wall
Bolts
5'-6"
1" min.
Helvetica Black CAUTION
Ear Protection
Required
1
At door 200-D102C
S-3
B
1014-011
7"
10"
White
Door/Wall
Screws/
Bolts
5'–6"
2-1/2"
Block
Black NOT AN EXIT
1
On door 200-D102A
X-1
G
1014-005
10"
14"
White
Wall
Bolts
6'-0"
6"
Block
Red
1
At exterior
stairwell door in
Digester
Expansion
EXIT
1
Numbers refer to a particular sign type with a particular message.
Letters refer to sign types specified in this section.
3
Numbers refer to Design Details that show sign layout.
4
Verify requirements for this sign with Laws and Regulations in state where Project is located.
2
PW/DEN001/650394
SEPTEMBER 17, 2015
©COPYRIGHT 2015 CH2M HILL
SIGNAGE
10 14 00 SUPPLEMENT - 1