COURSE OUTLINE
Department & Faculty: Department of Chemical Engineering
Faculty of Chemical & Natural Resources Engineering
Subject & Code: Thermodynamics and Strength of Material
Laboratory (SKC 2711)
Total Experiment Hours: 3 hours x 10 Experiments
Page: 1 of 3
Semester: 1
Academic Session: 2004/2005
Lecturer
Room No.
Tel. No.
E-mail
:
:
:
:
En. Ramli B. Mat
N01 - 315
07-5535567
ramli@fkkksa.utm.my
Section
Meeting Time
Venue
Assistant
:
:
:
:
01
Monday (2.00 – 5.00 pm)
Laboratory of Thermodynamics and Polymer Testing Laboratory
En. Nazeri Mahat and En Suhee Tan Hassan
Prerequisite
: SKC 2013 Thermodynamics and SKR 3013 Strength of Material (pass)
Synopsis
: This laboratory course contains 10 experiments that are covered basic concept
in Thermodynamics and Strength of Material. Laboratory experiments are
designed for hand-on experience to understand the engineering principles taught
in lectures. The topics covered are: Marcet Boiler, Stirling Cycle Hot Air Engine,
Pressure and Differential Pressure Measurement, Mixing of water at Different
Temperature, First and Second Law of Thermodynamics, Torsion of bars,
Compression Test, Bending Moment, Three Point Bending, and Tensile Test.
This course also emphasized the technical writing aspect where all students’
observation and arguments of each experiment must be reported in proper
format.
Learning Outcomes
: By the end of the course, students should be able to:
i)
Apply First and Second Law of Thermodynamics
ii)
Explain on how heat is converted to work.
iii)
Measure pressure and differential pressure
iv)
Determine the modulus of elasticity and Modulus of rigidity.
v)
Compare the tensile properties between materials.
Generic Skills
Addressed
:
Prepared by:
Name: Ramli B Mat
Signature:
Date:
1)
2)
3)
4)
Lifelong Learning (LL1)
Problem Solving (PS1 – PS2)
Communication Skills (CS1 – CS2)
Teamworking (TW1 – TW3)
Certified by: (Course Coordinator)
Name:
Signature:
Date:
COURSE OUTLINE
Department & Faculty: Department of Chemical Engineering
Faculty of Chemical & Natural Resources Engineering
Subject & Code: Thermodynamics and Strength of Material
Laboratory (SKC 2711)
Total Experiment Hours: 3 hours x 10 Experiments
Page: 1 2ofof3 3
Semester: 1
Academic Session: 2004/2005
Experiment
Topic
Learning Outcomes
1
Marcet Boiler
It is expected that students will be able to:
• Study the relationship between the
pressure and temperature of saturated
steam
• Compare dT/dP measured with values
calculated from data in steam tables.
2
Stirling Cycle Hot Air Engine
It is expected that students will be able to:
• Study the effect of changing
dynamometer load on engine speed
• Demonstrate on how heat is
converted to work.
3
Pressure and Differential Pressure
Measurement
It is expected that students will be able to:
• Compare two methods of measuring
pressure
• measure differential pressure using
manometer.
4
Mixing of Water at Different Temperature
It is expected that students will be able to:
• measure the final temperature of the
mixing water at two different
conditions
• demonstrate the energy balance
(First Law of Thermodynamics).
5
First and Second Law of Thermodynamics
It is expected that students will be able to:
• find the temperature changes of the
hot and cold water.
• determine the amount of heat lost
6
Torsion of bars
It is expected that students will be able to:
• investigate the relationship between
torque (T) and the angle of twist (φ) of
a circular cross section specimen
• determine the (G) of materials
Convert ladder diagram into program
7
Compression Test
It is expected that students will be able to:
• determine the modulus of elasticity, E
of materials in compression.
• To determine the ultimate strength in
compression
• To compare the properties of
materials in compression and in
tension
COURSE OUTLINE
Department & Faculty: Department of Chemical Engineering
Faculty of Chemical & Natural Resources Engineering
Subject & Code: Thermodynamics and Strength of Material
Laboratory (SKC 2711)
Total Experiment Hours: 3 hours x 10 Experiments
Module
Topic
Page: 13 of 3
Semester: 1
Academic Session: 2004/2005
Learning Outcomes
8
Bending Moment
It is expected that students will be able to:
• comprehend the action of moment of
resistance in a beam.
•
measure the bending moment at a
normal section of a loaded beam and
to check its agreement with theory.
9
Three Point Bending
It is expected that students will be able to:
• Determine the modulus of elasticity, E
through bending.
• confirm the formula of simple beam
theory
• observe the deflection of material
subjected to pure bending Set proper
simulation parameters
Tensile Test
It is expected that students will be able to:
• investigate the tensile properties of
materials, such as yield stress,
ultimate tensile strength, stress at
failure, modulus of elasticity and also
the percentage of elongation.
• compare the tensile properties
between materials.
10
Teaching Methodology
References
Assessment
:
: Group Work and Discussion, Group Report
1. Wylen G.V. , Sonntag R.,and Borgnakke C., Fundamentals of Thermodynamics, 6th
ed., John Wiley, New York, 2003
2.Yunus A. Çengel , Thermodynamics: An Engineering Approach, 4th ed, Mc Graw
Hill, 2002.
30% exam and 70% group report. Students will be awarded points based on
performance on their lab work as documented in their laboratory reports. Each group
has to submit one Group Report for each module. Each lab report can earn a
maximum score of 100 points broken down into the following categories: Abstract
(10%), Introduction (10%), Theory (10%), Methodology (10%), Result and discussion
(40%), Conclusion (10%) and Format (10%).