H-PAS PowerBar 235
Quick Start Guide
1
What’s in the Box?
Instruction Manual
2 tall feet
4 short feet
Remote Control
(with battery)
MUTE
MODE
SOURCE
SPEECH
•2-CHANNEL
•3-CHANNEL
•5-CHANNEL
•5-EXPANDED
1 PowerBar 235
BASS
TREBLE
VOLUME
AC Power Supply
Power Supply Cable
1 PowerBar Mounting Template
1 Optical Cable
Inverse Control Panel Label
SPEECH
SOURCE
2
MODE
BASS
TREBLE
S1 IN
Where should you locate your soundbar?
The PowerBar 235 can be used as a set-top or shelf-mounted speaker. Selfadhesive rubber feet are included to prevent vibration, protect the mounting
surface and serve to angle the speaker up or down if needed.
You may also simply mount the speaker to the wall using the built-in keyhole brackets or attach it to a suitably equipped articulating flat-panel TV
wall mount via the threaded inserts on the rear panel of the PowerBar 235.
For cabinet or shelf mounting, orient the speaker with
Control Pod on the top.
For wall mounting (or
mounting on a TV bracket),
orient the speaker with
Control Pod on the bottom
Side view
Side view
Use 2 of the small
round rubber spacers
to isolate the speaker
from the wall
Adhesive side
Use the 4 Small
round rubber spacers
for level placement
Rubber foot
Adhesive side
PowerBar 235 rear
Rubber feet
16" (406mm)
Use the 2 large rectangular feet with 2
of the small round
rubber spacers for
angled placement
24VDC 4A
IR IN
S2 IN
digital
coaxial
S3 IN
S4 IN
optical
S5 IN analog
L
SUB OUT
ON/OFF
R
415⁄16"
(125mm)
9 7⁄8" (251mm)
Use taller feet for up or down tilt
TREBLE
BASS
Step 2
Apply included inverse control panel label.
S1 IN
SPEECH
If you’re planning to wall-mount
your PowerBar in the inverse position (with the control pod on the
bottom) you will need to make a
few modifications.
Step 1
Remove label from Front Control Panel
by peeling down from the edge.
MODE
Wall Mounting?
SOURCE
3
Step 3
Turn unit over. Make sure unit is in STANDBY.
Press and hold both the UP and DOWN Volume keys at the same time until the Central
Display reads "UP" as shown. (To switch
orientation back, simply perform this operation again.)
SPEECH
SOURCE
BASS
MODE
TREBLE
S1 IN
Step 4
Remove and rotate the grille. To do so, gently pry the grille free from the cabinet starting at both ends. Continue to gently pry the grill
off moving towards the center of the cabinet. Do not use a tool or pick as this may damage the cabinet. Once the grille is free, rotate and
reattach. Make sure to line up the grille trees with the mounting cups. Press firmly until the grille is once again flush with the cabinet.
4
How should you connect it?
Rear of Cable Box or
Satellite Receiver
For optimum performance connect all your sources
directly to the PowerBar 235 using the digital output
from each source. This will guarantee the highest sound
quality and reduce the risk of signal loss.
Plug Power Cable
into AC Receptacle
COMPONENT OUT
COMPONENT OUT
DIGITAL
AUDIO OUT
(OPTICAL)
Optical cable 1 (one
included) from Digital
Audio Out to PowerBar
Source 3 (S3) Optical Input
Connect Power Supply
to Power Input Jack
on PowerBar
Connect Power Supply
Cable to Power Supply
DIGITAL
AUDIO OUT
(COAXIAL)
Rear of DVD Player
24VDC 4A
IR IN
DIGITAL
AUDIO OUT
(COAXIAL)
DIGITAL
AUDIO OUT
(OPTICAL)
Optical cable 2 (not
included) from Digital
Audio Out to PowerBar
Source 4 (S4) Optical Input
S2 IN
digital
coaxial
S3 IN
S4 IN
optical
S5 IN analog
L
SUB OUT
ON/OFF
R
Rear of PowerBar 235
5
Enjoy!
Remove battery insulator
tab from remote.
Turn unit on.
MUTE
MODE
SOURCE
SPEECH
•2-CHANNEL
•3-CHANNEL
•5-CHANNEL
•5-EXPANDED
BASS
TREBLE
Select source.
Adjust volume.
Enjoy!
See Instruction Manual for detailed
information.
If you have a question or comment, please call or email us. Call Atlantic
Technology Customer Service: 781.762.6300 (M-F 9-5 EST) or via email:
customerservice@atlantictechnology.com.
VOLUME
015-1236