VELOCITY II
OWNER’S MANUAL
1
Assembly Parts
ITEM#
DESCRIPTION
QTY
1
Upright
1
2
Frame
1
25
Front Stabilizer
1
27
Rear Stabilizer
2
29
Tube Shelf
1
30
Handrail
2
36
Computer
1
37
Seat
1
40
Adjustment Knob
1
51
Pedal (L)
1
52
Pedal (R)
1
2
Assembly Screws
ITEM#
DESCRIPTION
QTY
42
T-shaped Knob
1
43
Screw
2
44
Spring Washer
10
45
Arc Washer
6
46
Acorn Nut
2
47
Truss Hex Screw
8
48
Washer
4
49
Allen Wrench
1
50
Open Spanner
1
3
Assembly Instruction
concave
outward
1. Fix the Front Stabilizer (25) with Open Spanner (50), Screw (43), Spring Washer
(44), Arc Washer (45) and Acorn Nut (46). Plug the Rear Stabilizer into the Frame
and fix with Allen Wrench (49), Truss Hex Screw (47), Spring Washer (44) and
Washer (48). Please pay attention that the concave should be outward.
2. Assemble the left Pedal (51) and right Pedal (52) on the brace with Open Spanner
(50). (Please be attention that the marker “R” and “L” on right and left pedal is
corresponding to the one on the brace.)
4
3. Fix Seat (37) on the Tube (29) with Wrench (50), Nylon Nut (38) and Washer (39).
Untie the Knob (4) on the Frame, insert the Tube into the Frame and tie the Knob
(4).
4. Connect the thrum of the Sensor Wire (5) with the Guide Thread, pull upgrade
along the Upright (1). Plug the Upright into the Frame and tighten them with
Allen Wrench (49), Truss Hex Screw (47), Spring Washer (44) and Arc Washer
(45).
5
5. Plug the Adjustment Tightwire (18) into the Adjustment Knob (40) and then put
into the Upright (1). Fix them with Open Spanner (50) and Truss Philips Screw
(41).
6. Fix the Handrail (30) on the Upright (1) with T-shaped Knob (42).
6
7. Connect the tie-in of Sensor Wire (6) with the tie-in of the Computer (36). Then
insert the Computer (36) along with the computer plate and fasten the Screw (54)
and Washer (55) with Open Spanner. Plug the Hand Pulse Wire (34). Assembly
finishes.
7
Computer Operation Instructions
FRONTVIEW
Fig. 1
FUNCTION MARK:
1. SCAN: Auto scan
5. ⊙: Signal mark
2. SPEED: Speed
3. DIST: Trip distance
4. TIME: Riding time
6. ODO: Odometer
7. CAL: Calories
8.
: Pulse mark
SUMMARY: This monitor is equipped with an auto on/auto off function. The
computer will turn on automatically if the exercise machine is in motion. If stop
exercising for over 8 minutes, the computer will turn itself off.
HOW TO INSTALL BATTERY:
1.Take out the batteries from the back of monitor.
2.Place two pieces of SIZE-AA batteries into the battery housing.
3.Insure batteries are correctly positioned and battery spring is in proper contact
with batteries.
4.Battery life is approx. one year under normal usage.
5.If the display is illegible or only partial segments appear, remove the batteries and
wait 15 seconds or so, before reinstalling.
6.Removing the batteries will erase computer memory.
8
Fig. 2
FUNCTIONS AND OPERATIONS:
● RESET
Press the button more than 3 seconds will reset all functional values to zero
except ODO．
●
SCAN
Press the button until the arrow points to SCAN, monitor will automatically cycle
display TIME，SPEED，DIST，CAL and ODO.
●
SPEED:( unit=KM/H or MPH)
Press the button until the arrow points to SPEED, monitor will display the current
Speed. If the monitor display M in bottom-right, the unit of speed is MPH. If the
monitor do not display M in bottom-right, the unit of speed is KM/H.(MPH: Mile per
hour; KM/H: Kilometer per hour)
● DISTANCE:(unit=Kilometer or Mile)
Press the button until the arrow points to DIST, monitor will display the trip
distance you are traveling. If the monitor DISPLAY M in bottom-right，the unit of
distance is Mile. If the monitor do not display M in bottom-right，the unit of distance
is Kilometer．
● TIME:(unit=Minute:second)
Press the button until the arrow points to TIME．monitor will display your
exercising time．
● ODOMETER:(unit=Kilometer or Mile)
Press the button until the arrow points to ODO．monitor will display the total
accumulated distance．
● CALORIES:(unit=Calorie)
Press the button until the arrow points to CAL．monitor will display the
calories consumption．
● PULSE:(unit=Beats per minute)
Press MODE button until“
”appears at PULSE position．Before measuring
your pulse rate，Please place both your palms on the contact pads and the
9
monitor will show you r current heart beat rate in beats per minute(BPM)on the
LCD after 3~4 seconds．
Remark: During the process of pulse measurement，because of the contact
jamming，the measurement value may be higher than the virtual pulse rate
during the first 2~3 seconds, then will return to normal level．The measurement
value can not be regarded as the basis of medical treatment．
SPECIFICATIONS:
FUNCTION
Auto Scan
Every 4 seconds
Speed
Max.99.9Mile/h or
Km/H(orl200RPM)
Distance
0.01~99.99Mile or Kms
Time
0:00~99:59Minute: Second
Odometer
1~9999Miles or Kms
Calories
0.1~999.9~9999Kcal
Pulse
40-240BPM
Battery type
Operating Temperature
2 pcs of size AA or UM-3
0℃~+40℃(32℉~+104℉)
Storage Temperature
-20℃~+50℃(-40℉~+122℉)
10