Instruction Manual
4 in 1 Swing Set
4 in 1 Metal Swing Set
Instruction Manual
Page |1
Instruction Manual
4 in 1 Swing Set
Page |2
Warning
This unit is designed for a maximum of 6 children between the ages of 3 and 10 years
old.
Each seat has been tested to a maximum user weight of 49kg/110lb.
Please read the entire instruction manual before you start with the assembly or use
this swing set. Please check you have ALL required parts BEFORE you start
assembling.
You must follow all safety instructions while using this equipment. Be absolutely sure
that the surface on which you are to build this swing set is level and has an
appropriate surface. We strongly recommend using a safety surface of play bark or
rubber mats to ensure the ground beneath the swing set is not too hard. Do not use
this swing set on hard pack soil, concrete or any kind of hard surface.
Please read all safety advice and instructions before using this equipment.
Important Safety Information
Please follow these instructions carefully and keep them for future reference:
1. This swing set must be assembled by an adult
2. All nuts and bolts must be tightened properly both during and after assembly – regularly check
the screws, nuts and bolts are tight as they can loosen over time (we suggest monthly checks)
3. Suspension systems, Anchor points and fixings must be checked regularly for wear and tear and
replaced where necessary
4. Ropes may need to be replaced every 12 months depending on wear and tear
5. All bolts must be protected by the rubber caps provided
6. This swing set is recommended for outdoor use – ensuring at least 2.5m clearance in front and
behind the swings for safety
7. This swing set is recommended for a soft outdoor surface such as grass, play bark or rubber
matting
8. It is recommended that the swing legs are concreted or dug into the ground – if this is not
possible the ground anchors provided must be used
9. Do not install this swing set on very hard surfaces such as patios or concrete
10. This unit must be used under the supervision of adult – do not leave children unattended
whilst on this play equipment
11. Children should be shown proper use of the swing before playing on the equipment – do not
allow children to use the cross beam supports on the frame as a tumble bar as this could cause
them injury
12. Seats should be suspended no more than 60cm from the ground
13. Do not allow children to stand on the seats
14. Not suitable for children under 3 years due to small parts
15. For family domestic use only
Instruction Manual
4 in 1 Swing Set
Page |3
Swing Frame Parts List
Please ensure you have identified and counted ALL listed parts BEFORE you begin assembly.
1. CARTON PACK (F Screws bag)
PART NO
NAME
Q'TY
PART NO
NAME
Q'TY
1
Top Support Bar
1
J3
M8X70 Hex Bolt
7
2
Swing Set Leg
4
J2
M8X60 Hex Bolt
8
3
A-frame Cross Beam (With Safety Cap)
2
J1
M8X25 Hex Bolt
6
4
Swing Set Corner Bracket (A)
2
K5
M6X55 Hex Bolt
4
5
Swing Set Corner Bracket (B)
2
U1
M6 Safety Nut
4
6
Half Circle Connector
6
U2
M8 Safety Nut
21
7
Hanger Support Channel
3
X1
M6 Nylon Washer
4
8
Ground Anchor
4
X2
M8 Nylon Washer
21
9
Plastic insert
2
11
M6 Socket Wrench
1
10
Spanner
1
12
M8 Socket Wrench
1
3
4
5
1
2
J3
U1
11
6
J2
U2
7
J1
X1
12
These instructions are made up of five parts:
1. Assembling the Swing Frame
2. Assembling the Swing Seat
3. Assembling the ‘Gondola’ (facing swing seats)
X2
8
K5
9
10
Instruction Manual
4 in 1 Swing Set
Page |4
4. Assembling the Tandem Rocking Seats
5. Assembling the Trapeze Bar
-1Assembling the Swing Frame
•
•
Fig A: Insert the ‘Half Circle Connector’ (part 6) upwards into the ‘Hanger Support Channel’ (part 7)
Fig B: Thread the assembled component in Fig. A through the ‘Top Support Bar’ (part 1) – there will be
three complete components in total.
•
Slide the assembled components into the positions where you want the swings – two of these are for
the double facing seats (the ‘gondola’) and one is for the other tandem rocking swing. To fasten them in
place, attach another half circle connector (part 6) to it using Hex Bolt (J1), Hex Bolt (J3), M8 Iron
Washer (X2) and M8 Safety Nut (U2).
Instruction Manual
4 in 1 Swing Set
Page |5
•
Fig. D: Connect both of the ‘Swing Set Corner Brackets (A)’ (part 4), and the ‘Swing Set Corner
Brackets (B)’ (part 5) to the top support bar at both ends with the following bolts and washers:
Hex Bolt (J2), M8 Iron Washer (X2), M8 Safety Nut (U2).
•
Insert each of the ‘Swing Set Legs’ (parts 2) into the bottom of the swing set corner brackets (which
should now be attached to the top support bar, leaving a tubular gap) at both ends. Connect the legs
(parts 2) to the swing set end brackets with Hex Bolt (part A3), M8 Nylon Washer (part X2), M8 Safety
Nut (part U2).
•
Connect the two ‘A-frame Cross Bars’ (parts 3) to the swing set legs (parts 2) using M6X55 Hex Bolt
(part K5), M6 Iron Washer (part X1), M6 Safety Nut (part U1) for both sides.
-2 Assembling the Swing Seat
Parts Needed:
PART NO
NAME
Q'TY
PART NO
NAME
Q'TY
1
Swing Seat Set
1
U2
M8 Safety Nut
8
G4
M8 U-Bolt
4
X2
M8 Iron Washer
8
1
U2
X2
G4
Hang the Swing Seat Set (part 1) onto the U-Bolts (parts G4) – then screw this into the top support bar of the
swing frame using the M8 Safety Nuts (parts U2), washer (parts X2). The swing should hang between 400 and
600mm from the ground, so adjust the seat accordingly and so it sits level.
Instruction Manual
4 in 1 Swing Set
Page |6
-3Assembling the Tandem Rocking Swing
Parts Needed: (Screws Bag B):
PART NO
NAME
Q'TY
PART NO
NAME
Q'TY
1
Hanger Tube
2
K6
Bolt M6X90mm
2
2
Seat Tube
2
K3
Bolt M6X45mm
2
3
Rigid-Swing Seat
2
K2
M6X65mm
2
4
Foot Rest
2
U1
M6 Safety Nut
14
C1
Bolt M6X45mm
8
X1
M6 Iron Washer
16
1
C1
2
K6
3
K3
K2
4
U1
X1
1. Place the two ‘Rigid Swing Seats’ (parts 3) onto the two ‘Seat Tubes’ (parts 2). Screw each seat on with 4 x
bolts (C1), 4 x washers (X1) and 4 x M6 nuts (U1).
2. Screw the two ‘Seat Hangers’ (parts 1) between the assembled seat tubes (parts 2) with 2 x bolts (K6), 2 x
washers (X1) and 2 x safety nuts (U1).
Instruction Manual
4 in 1 Swing Set
Page |7
3. Place the two ‘Foot Rests’ (parts 4) onto the bottom ends of the two seat hangers (parts 1).
Screw them in place with 2 x bolts (K2), 2 x washers (X1) and 2 x M6 Safety nuts (U1).
4. Attach the assembled swing to the pre-assembled component (hanger support channel with two half circle
connectors) on the top support bar (from page 4 – Figs A-C) using 2 x bolts (K3), 2 x washers (X1) and 2 x
M6 safety nuts (U1).
-4Assembling the ‘Gondola’ (double facing seats)
Parts Needed (Screws Bag A):
PART NO
NAME
Q'TY
PART NO
NAME
Q'TY
1
Hanger
4
K4
Bolt M6X55mm
8
2
Seat Tube
4
K1
Bolt M6X20mm
4
3
Fixed Tube
2
K3
Bolt M6X45mm
4
4
Seat Board
6
U1
M6 Safety Nut
40
K2
Bolt M6X35mm
8
X1
M6 Iron Washer
80
K5
Bolt M6X50mm
16
1
5
2
K2
U1
3
K3
K4
X1
X3
K1
Instruction Manual
4 in 1 Swing Set
Page |8
1. Figure 1: Assemble one seat board (5) onto seat tube (2) using bolt (K5), washer (X1) and safety nut (U1) this will be a back rest.
2.Figure 2:Assemble one seat board (5) onto seat tube (2) using bolt (K5), washer (X1,) and safety nut (U1) this will be an actual seat.
3. Figure 3:Connect hanger (1) and seat tube (2), using bolt (K2),washer (X1) and safety nut (U1).
Assemble the other side of the Gondola (double facing swing) by repeating steps 1 - 3 in the same way.
4. Figure 4: Assemble two seat boards (5) on fixed tube (3) using bolt (K4), washer (X1) and safety nut (U1) -
Instruction Manual
4 in 1 Swing Set
Page |9
these will be the foot rests.
5. Figure 5: Connect the assembled fixed tube and the assembled seat tube, using bolt (K1), washer (X1) and
safety nut (U1), you have then completed the gondola swing.
6. Hang the assembled rocking chair onto the hanger clip of the top support bar; fasten them tight with bolt (K3),
washer (X1) and safety nut (U1).
-5-
Instruction Manual
4 in 1 Swing Set
P a g e | 10
Assembling the Trapeze Bar
Parts Needed:
PART NO
NAME
Q'TY
PART NO
NAME
Q'TY
1
Trapeze Bar
1
U2
M8 Safety Nut
4
G4
M8 U – Bolt
2
X2
M8 Iron Washer
4
1
G4
U2
X2
1: Hang the Trapeze Bar (part 1) onto the two M8 U-Bolts (parts 2) -
3. Thread the U-screws (part G4) onto the Height Adjusters then fix the U-screws to the top support bar of the
swing frame using safety nut (U2) and washer (X2) (shown in diagram above). Adjust the ropes to ensure the
two rings and bar are level and the height of the rings are between 107cm and 132cm from the ground.
CARE AND MAINTENANCE
Instruction Manual
4 in 1 Swing Set
P a g e | 11
This swing set has been designed and manufactured with quality materials and craftsmanship. With
proper care and maintenance, it will provide children with years of exercise, fun, and enjoyment.
Please follow the guidelines below.
This swing set is designed to withstand a specific weight. Children over 110 pounds (50kgs) should not
use the swing set. Children should remove all sharp objects from their person prior to using the swing
set. All sharp or pointed objects should be kept off the playground at all times.
Always inspect the swing set before each use for worn, damaged or missing parts. Please be aware of:
Loose or missing bolts
Sagging in the top support bar
Bent or broken frame parts, such as the support leg
Broken, missing, or damaged seats
Damaged, missing, or insecurely attached rope
Protrusions of any type (especially sharp protrusions) on the frame or in any other place
If you find any of the above issues, or anything else that you feel could cause harm to any user, the
swing set should be disassembled or remain unused until the issue or issues can be rectified.
Please retain these details for future reference. Big Game Hunters is the retail division of Garden Games Ltd.
Garden Games Ltd., Holly House, Pine Woods Road, Longworth, Oxfordshire, OX13 5HG, England
Tel + 44 (0)1865 391060