AS/EN/SJAC 9102 Rev A First Article Inspection
Form 1: Part Number Accountability
1. Part Number
1024555
5. Part Revision Level
2. Part Name
6. Drawing Number
Assembly FAI
a)
b)
05013
7. Drawing revision level
8. Additional Changes
004
10. Organization Name
N/A
11. Supplier Code
ViaSat, Inc.
14.
4. FAI Report Number
00-002248
1024563
1018347
13. Detail FAI
3. Serial Number
ASSY, GENAV 6MCU UNIT
006
9. Manufacturing Process
Reference
Sheet 1 of 1
12. P.O. Number
47358
Full FAI
Partial FAI
10021 Rev. 1
Baseline Part Number including revision level
Reason for Partial FAI:
if above part number is a detail part only, go to Field 19
if above part number is an assembly, go to the “INDEX” section below.
INDEX of part numbers or sub-assembly numbers required to make the assembly noted above.
15. Part Number
16. Part Name
17. Part Serial Number
18. FAI Report Number
1024568
OUTLINE DWG.
00-002248
See FAIR #05014
ASSY,CHASSIS
00-003003
1024559
1016555
1016555
1000850
1001145
1015609
PWA, RECEIVER MODULE,
TESTED (A1)
PWA, RECEIVER MODULE,
TESTED (A2)
PWA, TRANSMITTER MODULE,
TESTED (A3)
ASSY, SPLITTER/SWITCH
MODULE (A4)
ASSY, SERVER/ROUTER
MODULE (A5)
02-003790
15-007173
See FAIR #05012
ECO Justification (See FAIR
#05004)
ECO Justification (See FAIR
#05004)
02-004198
Same as NGA
719325
Same as NGA
132523
QTAI stamp off
ECO Justification (See FAIR
#05006)
1024562
ASSY, POWER SUPPLY
GN0502001
1026199
CABLE ASSY. SMB-SMB, LONG
N/A
QTAI stamp off
CABLE ASSY. SMB-SMB, SHORT
N/A
ECO Justification (See FAIR
#05009)
VF-017381-0001
LBL, IDENTIFICATION
N/A
Same as NGA
1027033
LBL, IDENTIFICATION, BLK LABEL
N/A
See FAIR #05001
VF-017238-0000
LABEL ELECTRO-STATICDISCHARGE
N/A
Same as NGA
1024572
TOP COVER, CHASSIS
N/A
QTAI stamp off
1007347
LABEL, ORIENTATION
N/A
See FAIR #05002
1026201
ASSY. SHPG MATERIALS
N/A
N/A
1026198
1) Signature indicates that all characteristics are accounted for; meet drawing requirements or are properly documented for
disposition.
2) Also indicate if the FAI is complete per Section 5.4:
19. Signature
FAI complete
FAI not Complete
20. Date: 11/02/05
21. Reviewed By
22. Date
23. Customer Approval
24. Date
Form 1, 9102 Rev A, Date: Oct 31, 2003
AS/EN/SJAC9102 Rev A First Article Inspection
Sheet 1 of 1
Form 2: Product Accountability – Raw Material, Specifications and Special Process(s),
Functional Testing
1. Part Number
1024555
2 Part Name
3. Serial Number
ASSY, GENAV 6MCU UNIT
7. Code
00-002248
5. Material or Process
Name
6. Specification
Number
11. Functional Test
Procedure Number
12. Acceptance report number, if applicable
1024564
SEE TEST DATA DATED 10/26/05
1029175
SEE TEST DATA DATED 10/25/05
8. Special Process
Supplier Code
13. Comments
14. Prepared By: Bernard Mondy, QA Specialist
Form 2, 9102 Rev A, Date: Oct 31, 2003
4. FAI Report
Number
15. Date: 11/02/05
05013
9. Customer
Approval
Verification
(Yes/No/NA)
10. Certificate of
Conformance
number
AS/EN/SJAC9102 Rev A First Article Inspection
Form 3: Characteristic Accountability, Verification and Compatibility Evaluation
1. Part Number
2. Part Name
3. Serial Number
1024555
ASSY, GENAV 6MCU UNIT
Characteristic Accountability
Inspection / Test Results
5.
6.
7.
8. Requirement
Char Reference Characteristic
No.
Location
Designator
N/A
NOTE 1
1 ZONE 1D8
Sheet 1 of 1
9. Results
10. Designed
Tooling
CONFORMS
N/A
4. FAI Report
00-002248
11. NonConformance
Number
N/A
14.[Insert columns, etc, as required by Organization or Customer]
2
ZONE 1D8
N/A
NOTE 2
CONFORMS
N/A
N/A
3
ZONE 1D8
N/A
NOTE 3
CONFORMS
N/A
N/A
4
ZONE 1D8
N/A
6 - 8 IN - LBS
N/A
N/A
5
ZONE 1D8
N/A
NOTE 4
6 – 8 IN - LBS
NOTE 5
CONFORMS
N/A
N/A
6
ZONE1 D8
N/A
NOTE 6
CONFORMS
N/A
N/A
7
ZONE 1D8
N/A
NOTE 7
SEE TEST REPORT
N/A
N/A
SEE TEST DATA DATED 10/26/05
8
9
ZONE 1C8
N/A
NOTE 8
SEE TEST REPORT
N/A
N/A
SEE TEST DATA DATED 10/25/05
ZONE 1C8
N/A
NOTE 9
CONFORMS
N/A
N/A
10
ZONE 1C8
N/A
NOTE 10
CONFORMS
N/A
N/A
11 ZONE 1C8
N/A
NOTE 11
CONFORMS
N/A
N/A
12 ZONE 1C8
N/A
NOTE 12
CONFORMS
N/A
N/A
13 ZONE 2D7
N/A
2.50 +/-.25 2X
2.52
N/A
N/A
14
ZONE 2A7
N/A
.25 4X
.20
N/A
N/A
15
ZONE 2A6
N/A
7.0 +/-.1 2X
7.05
N/A
N/A
The signature indicates that all characteristics are accounted for; meet drawing requirements or are properly documented for disposition.
12. Prepared By: Bernard Mondy, QA Specialist
Form 3, 9102 Rev A, Date: Oct 31, 2003
05013
13. Date: 11/02/05