Miracote®
Installation Guideline
Membrane A
Liquid Waterproofing Membrane
Unreinforced and Reinforced:
Unreinforced – Horizontal Surface
INSTALLATION INSTALLATION
GUIDELINE
METHODS
STEP 1
Primer
STEP 2
1ST Coat
Membrane
STEP 3
2nd Coat
Membrane
Dip-n-Roll
Note: Single
Component
Materials Require
Careful Premixing
Notched Squeegee
and
Back Roll
or
Dip-n-Roll
Note: Single
Component
Materials Require
Careful Premixing
Notched Squeegee
and
Back Roll
or
Dip-n-Roll
PRODUCTS
AND
MIX RATIOS
Membrane A
(Mix Ratio: Split 1:1 with
Clean Potable Water)
Note: Cut Prime Coat only
with Water
Membrane A
COVERAGE RATE
1000 sq/ft PER
USA GALLON/POUND
(APPROXIMATE)
400 sq/ft per mixed gal
2.5 gal per 1000 sq/ft
(4 mils WFT)
penetrates
64 sq/ft per gal
15.6 gal per 1000 sq/ft
(25 mils WFT)
(12.5 mils DFT)
Membrane A
64 sq/ft per gal
15.6 gal per 1000 sq/ft
(25 mils WFT)
(12.5 mils DFT)
Note: Single
Component
Materials Require
Careful Premixing
Page 1 OF 3
Miracote is a registered trade name of Crossfield Products Corp.
ICH 161 001/03
Miracote®
Installation Guideline
Reinforced – Horizontal Surface:
INSTALLATION INSTALLATION
GUIDELINE
METHODS
Step 1
Primer
STEP 2A
1ST Coat
Membrane
STEP 2B
Embedded
Reinforcing Fabric
Dip-n-Roll
Note: Single
Component
Materials Require
Careful Premixing
Notched Squeegee
and
Back Roll
or
Dip-n-Roll
Note: Single
Component
Materials Require
Careful Premixing
Immediately
Unroll Fabric and
Embed into Wet
Membrane A
PRODUCTS
AND
MIX RATIOS
COVERAGE RATE
1000 sq/ft PER
USA GALLON/POUND
(APPROXIMATE)
Membrane A
(Mix Ratio: Split 1:1 with
Clean Potable Water)
400 sq/ft per mixed gal
2.5 gal per 1000 sq/ft
Note: Cut Prime Coat only
with Water
Membrane A
(Single Component)
(4 mils WFT)
penetrates
64 sq/ft per gal
15.6 gal per 1000 sq/ft
(25 mils WFT )
(12.5 mils DFT)
Plus Fabric
RP I Fabric
(1,000 sq/ft roll)
Overlap minimum of 2” at
the seam. Fabric demand will
vary based on configuration,
penetrates, etc.
Note: Must see continues
film of Membrane A, if
jobsite irregularities cause
deficiency add more
Membrane A as needed.
Page 2 OF 3
Miracote is a registered trade name of Crossfield Products Corp.
ICH 161 001/03
Miracote®
Installation Guideline
INSTALLATION INSTALLATION
GUIDELINE
METHODS
STEP 3
1st Coat (saturant)
Membrane
STEP 4
2nd Coat (saturant)
Membrane
NOTE:
Notched Squeegee
And Back Roll
or
Dip-n-Roll
Note: Single
Component
Materials Require
Careful Premixing
Notched Squeegee
And Back Roll
or
Dip-n-Roll
PRODUCTS
AND
MIX RATIOS
Membrane A
(Single Component)
COVERAGE RATE
1000 sq/ft PER
USA GALLON/POUND
(APPROXIMATE)
64 sq/ft per gal
15.6 gal per 1000 sq/ft
(25 mils WFT)
(12.5 mils DFT)
Membrane A
(Single Component)
64 sq/ft per gal
15.6 gal per 1000 sq/ft
(25 mils WFT)
(12.5 mils DFT)
Note: Single
Component
Materials Require
Careful Premixing
Prior to starting the installation of any Miracote Product or System be sure to read
the Installation Guideline Manual, Appendices, MSDS and other pertinent
documents.
Pay special attention to substrate moisture content, physical condition of the
substrate, method(s) of surface preparation, restoration, detailing of cracks/joints,
transitions, terminations and specification. Review carefully for unknown site
conditions or defects.
The Installation Guideline numbers are for estimating purposes only. Wastage,
uneven substrate and other unforeseen site conditions may affect the actual yields.
See Crossfield Products Corp., Miracote Installation Guideline Manual, Product
or System Information Sheet and Price Book for Limitations, Disclaimers and
Limited Warranty.
PRECAUTIONS:
Review and Follow Precautions Listed in the Miracote Installation Guideline prior
to execution of work.
Page 3 OF 3
Miracote is a registered trade name of Crossfield Products Corp.
ICH 161 001/03