Guardian Protective Coatings Pty Ltd Email:gary@guardit.net A.C.N. 061 748 543 PRODUCT INFORMATION SHEET PRODUCT: GUARDIAN CERAMIC PRIMER Product Code: GCPPI Issue Date: January 2015 Page 1 of 1 Description Guardian Ceramic Primer is a high performance one coat silane adhesive primer with UV tracer designed to bond Guardian Ceramic Coating satin/gloss to ceramic tiles, formica, glass and porcelain and has the capability for QC monitoring of the primed surface. To accomplish this, Guardian Ceramic Primer contains a special UV fluorescing agent which permits close visual scrutiny of the adhesive coated surface to reduce variability and wasteage. Low intensity UV lamps are hung in the QC area or near the priming line to visually observe continuity, coating weight, and detect improper wetting due to surface contamination. The UV fluorescing agent does not affect adhesion or shelf stability of the primer. Application/Surface Preparation Guardian Ceramic Primer is best applied by spray application in a light even coat. Typical coverage via spray application to non porous substrates 30m2 @ 2micron DFT It is recommended that the substrate be thoroughly degeased with solvent degreaser. The adhesive coated surface should be permitted to hydrolyze in moist air (50-80% RH) for one hour prior to application of the Guardian Ceramic Coating. For best results, it is recommended that the time between priming and application of the finish coat remain under 24 hours. Repriming will restore bondability when required. Specification Sheets Before application refer to the corresponding Material Safety Data Sheets GCPMSDS. Shelf Life: 12 months in closed containers Safety Precautions Keep out of reach of children. Avoid contact with eyes, wear safety goggles. Wash thoroughly after using or before smoking or eating. Avoid contact with skin, wear PVC or rubber gloves. Avoid prolonged breathing of vapors and/or mists. Ensure adequate ventilation. For spray application and working in confined areas wear a positive pressure air supplied respirator. For short periods of work a combination of charcoal filter and particle filter is recommended. Harmful or fatal if swallowed. If swallowed, do not induce vomiting. Call a physician immediately. Treat symptomatically. First Aid If poisoning occurs, contact a doctor or Poisons Information Centre. If swallowed, do not induce vomting. Give a glass of water. If skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and water. If overcome by fumes remove from contaminated area. Apply artificial respiration if not breathing. If in eyes, hold eyes open, flood with water for at least 15 minutes and see a doctor. Storage and Handling Keep away from heat sparks and open flame. Store in a cool and dry place. Do not open until ready to use. Protect from moisture. Keep storage containers full. Guardian Ceramic Primer is ready to use. Do not dilute. Diluents introduce moisture. The statements above are compiled from our field of production and according to the latest technological developments and application techniques. Since application and working are beyond our control, no liability of the producer can be derived from the contents of this information sheet. Guardian Protective Coatings Pty Ltd and associated group of companies shall not be responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere or observe the recommendations, or from any hazards inherent in the nature of the material. It is the users responsibility to evaluate the information contained herein and use this product safely and within the current laws and regulations. Prodinfo.cer.doc Guardian Protective Coatings Pty Ltd Email:gary@guardit.net A.C.N. 061 748 543 MATERIAL SAFETY DATA SHEET PRODUCT: GUARDIAN CERAMIC PRIMER Product code: GCPMSDS Issue Date: January 2015 Page No: 1 of 3 Worksafe Hazard Assessment: Hazardous According To Criteria Of Worksafe Australia Company details: Guardian Protective Coatings Pty Ltd UN: 1133 SUB RISK: None Allocated EPG: 26 POISON SCHEDULE: 5 CLASS: 3 HAZ CHEM CODE: 3[Y]E PACKAGING GROUP: II USES: One coat adhesive primer. PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE: Clear, colorless fruity odour BOILING POINT: 78-171°C VAPOUR PRESSURE: Not Done SPECIFIC GRAVITY: 0.89 g/lt FLASH POINT: 2°C VOLATILES: 87% EVAPORATION RATE(nBA=1): moderate/slow MELTING POINT: Not Applicable VAPOUR DENSITY(AIR=1): >1 SOLUBILITY(WATER): Insoluble EXPLOSION LIMITS: LEL 1.1% UEL 19.0% pH: Not Applicable INGREDIENTS Chemical Name Toluene n-Butanol 2-Butoxyethanol Ethyl alcohol CAS Number 108-88-3 71-36-3 111-76-2 64-17-5 Proportion 60% 10% 10% 10% HEALTH HAZARD INFORMATION INGESTION: Harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial use. EYE: Irritant to eyes. Over exposure may cause lacrimation and redness. SKIN May be absorbes through the skin in harmful amounts. May cause skin irritation. Will dry on skin if not removed. Contact causes drying and defatting of the skin. Prolonged contact may cause dermatitis. INHALATION: Irritant to respiratory tract. Prolonged or repeated exposure may lead to symptoms such as dryness of the throat, tightness of the chest and shortness of breath. May cause central nervous system depression characterised by the following progressive steps: headache, dizziness, staggering gait, confusion, unconsciousness or coma. May cause headache and nausea. Aspiration of liquid into the lungs can cause serious pneumonitis. CHRONIC May cause liver or kidney damage. Repeated or prolonged solvent exposure may result in permanent central nervous system damage. May affect the blood and blood-forming organs. Inhalation, skin absorption, ingestion and eye contact are the primary routes of entry into the body. Chronic skin contact may cause dermatitis. msds.cer.doc MATERIAL SAFETY DATA SHEET PRODUCT: GUARDIAN CERAMIC PRIMER Guardian Protective Coatings Pty Ltd Email:gary@guardit.net A.C.N. 061 748 543 Product code: GCPMSDS Issue Date: January 2015 TOXICITY DATA Accurate data for this product is not available. EXPOSURE STANDARD No exposure standards have been established for this product. Exposure Guidelines on skin ACGIH OSHA Toluene n-Butanol 2-Butoxyethanol Ethyl alcohol Page No: 2 of 3 STEL 50ppm n.e. TWA TWA Ceiling not established 200ppm 300ppm 50ppm 100ppm not established 25ppm not established 50ppm not established 1000ppm not established 1000ppm not established FIRST AID PROCEDURES INGESTION NEVER GIVE AN UNCONSCIOUS PERSON ANYTHING TO DRINK NOR ATTEMPT TO INDUCE VOMITING. If person is conscious, rinse mouth out with water ensuring that mouth wash is not swallowed. Give about 250ml (2 glasses) of water to drink. DO NOT attempt to induce vomiting. Seek medical attention. EYE Hold eyelids open and rinse the eye continuously with a gentle stream of clean running water for at least fifteen minutes. Seek medical attention. SKIN Remove contaminated clothing and wash thoroughly with soap and water. Use water alone, if soap is unavailable. Apply a moisturising hand cream, if available. Seek medical attention if any soreness or inflammation of the skin persists or develops later. Launder affected clothing before re-use. INHALATION Remove to fresh air. Keep warm and at rest. If breathing is laboured, hold in a half upright position (this assists respiration). Apply artificial respiration if breathing has stopped. Seek medical attention. PRECAUTIONS OF USE ENGINEERING CONTROL Do not inhale vapours. Ensure good ventilation (dilution and local exhaust) in storage and use. The ventilation system should be non-sparking and grounded and separate from other exhaust ventilation systems. Where there is large scale use of this material, local exhaust ventilation with or without process enclosure may be necessary. Supply sufficient replacement air to make up for air removed by exhaust systems. The exhaust extract must be directed outside the building and at a point 1.25 times the building height to avoid fume re-entry. Caution: Solvent vapours are heavier than air and collect in lower levels of the work area. PERSONAL PROTECTION EYE/FACE PROTECTION Chemical safety goggles with side shields or face shield. SKIN PROTECTION Impervious gloves, coveralls, boots and/or other resistant protective clothing. Easy access to a safety shower, eye wash fountain in the work area. RESPIRATORY PROTECTION If engineering controls and work practices are not effective in controlling exposure to the material then wear approved respiratory protection with organic vapour/particulate respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716. For airborne concentrations up to 1000ppm use a full face respirator fitted with a Class 2, Type A respirator. . When spraying in areas with insufficient or no replacement air, an approved full face air supplied respirator, full length chemically resistant coveralls and boots and gloves are recommended. N.B. TAKE THE LIMITS OF ABSORPTION CAPACITY INTO ACCOUNT. CHANGE FILTERS REGULARLY AIR PURIFYING RESPIRATORS DO NOT PROTECT AGAINST OXYGEN DEFICIENT ATMOSPHERES. msds.cer.doc MATERIAL SAFETY DATA SHEET PRODUCT: GUARDIAN CERAMIC PRIMER Guardian Protective Coatings Pty Ltd Email:gary@guardit.net A.C.N. 061 748 543 Product code: GCPMSDS Issue Date: January 2015 Page No: 3 of 3 FLAMMABILITY Highly flammable. If the product is heated, vapours can form flammable mixtures with air in poorly ventilated conditions. May evolve toxic fumes if heated strongly or burned. The product may react with strong oxidising agents, acids and bases. Hazardous decomposition products may be carbon dioxide, carbon monoxide, chlorine, hydrogen chloride and phosgene. This product is stable under normal storage conditions. SAFE HANDLING PROCEDURES STORAGE TRANSPORT Usual precautions for Class 3. Store out of direct sunlight in a cool well ventilated area below 25C. Higher temperatures may cause pressure build up inside containers. Segregate from oxidising agents and acids. Protect containers against physical damage. Empty containers may contain product residue and flammable vapours, keep away from heat, sparks and flame; do not cut, puncture or weld on or near empty containers. Do not smoke where this product is used or stored. RISK PHRASES SAFTEY PHRASES R10: Flammable S2: Keep out of reach of children R20: Harmful by inhalation S16: Keep away from sources of ignition -no smoking R21: Harmful in contact with skin S24/25: Avoid contact with skin and eyes R22: Harmful if swallowed S29: Do not empty into drains R37: Irratating to respiratory system S33: Take precautionary measures against static discharges PACK SIZE SHELF LIFE 250ml , 1lt DG screw top metal containers. 1 year in unopened container SPILLS DISPOSAL SPILLS: Ensure that there are no sources of ignition present. Remove unnecessary personnel from the affected area. Wear protective equipment as specified for handling. If possible, dam the spill. Cover with an absorbent such as earth, sand or a commercial oil absorber. DO NOT use combustibles such as sawdust. Sweep up and collect for disposal. Do not empty into drains. DISPOSAL: If possible, return to supplier. Otherwise dispose in accordance with the local authority, or to approved landfill. FIRE EXPLOSION Combustible. Containers may rupture if heated strongly. Wear self contained breathing apparatus. If possible remove containers from the vicinity of the fire. Otherwise keep containers as cool as possible by spraying with water, from a protected position. Water is not effective for fire fighting and direct contact with water should be avoided. Extinguish using foam, dry chemical or carbon dioxide. CONTACT POINT Emergency Advice Issue date: Supersedes issue date: Reason for issue: January 2015 February 2008 Company details. APPROVED BY : G.J. Dwyer 13 11 26 Poisons Information Center This data sheet and the health and safety hazard information it contains is considered to be accurate as at the date of issue. However, no warranty or recommendation, express or implied, is made as to the accuracy or completeness of the data and information contained within. Each user should read this data sheet and consider the information in the context of how the product will be handled and used. Health and safety precautions mentioned in this data sheet may not be accurate for all individuals and/or situations. Guardian Protective Coatings and associated group of companies shall not be responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere or observe the recommendations, or from any hazards inherent in the nature of the material. It is the users responsibility to evaluate the information contained herein and use this product safely and within the current laws and regulations. msds.cer.doc