DAS Design Specification
Includes Installation Instructions
Implementation: July 2009
533569390
Page 1 of 43
TABLE OF CONTENTS
1.
PURPOSE..............................................................................................................................................5
2.
SCOPE...................................................................................................................................................5
3.
NOTES TO DESIGN & INSTALLATION CONTRACTORS ...................................................................5
4.
OHS&E ISSUES ....................................................................................................................................5
5.
DESIGN SPECIFICATION.....................................................................................................................5
5.1.
General DAS Description.............................................................................................................5
5.1.1.
Passive DAS ........................................................................................................................6
5.1.2.
Active DAS ...........................................................................................................................6
5.2.
Operating Frequency Bands ........................................................................................................6
5.2.1.
5.3.
Alternative frequency ranges ...............................................................................................6
DAS Capability .............................................................................................................................7
5.3.1.
Passive DAS ........................................................................................................................7
5.3.2.
Active DAS ...........................................................................................................................7
5.4.
Target Coverage Area .................................................................................................................7
5.5.
RF Levels Required .....................................................................................................................7
5.5.1.
GSM900 ...............................................................................................................................8
5.5.2.
3G850 ..................................................................................................................................8
5.5.3.
DCS1800..............................................................................................................................8
5.5.4.
3G2100 ................................................................................................................................8
5.6.
Handover Zone ............................................................................................................................9
5.7.
DAS Configuration .......................................................................................................................9
5.7.1.
Passive DAS Interconnect Ports ..........................................................................................9
5.7.2.
Active DAS Interconnect Ports...........................................................................................10
5.8.
Radiated Power Levels ..............................................................................................................10
5.8.1.
Passive DAS ......................................................................................................................10
5.8.2.
Active DAS .........................................................................................................................11
5.9.
533569390
Electromagnetic Immunity .........................................................................................................11
Page 2 of 43
6.
5.10.
Base Station Power Levels ........................................................................................................12
5.11.
Maximum Signal Received by MS/UE .......................................................................................12
5.12.
Minimum Allowable Path Loss ...................................................................................................12
5.12.1.
Passive DAS ......................................................................................................................12
5.12.2.
Active DAS .........................................................................................................................13
5.13.
Propagation Model.....................................................................................................................13
5.14.
Measured performance of installed DAS ...................................................................................13
5.14.1.
Return loss .........................................................................................................................13
5.14.2.
Passive intermodulation .....................................................................................................13
5.15.
Cable and Component Labelling ...............................................................................................13
5.16.
Preferred Material List ...............................................................................................................14
5.17.
Other Equipment Specifications ................................................................................................14
5.17.1.
Characteristic impedance ..................................................................................................14
5.17.2.
VSWR ................................................................................................................................14
5.17.3.
Intermodulation ..................................................................................................................14
5.17.4.
Coaxial connector types .....................................................................................................14
5.17.5.
Patch cables.......................................................................................................................15
DELIVERABLES ..................................................................................................................................15
6.1.
Documentation ...........................................................................................................................16
6.2.
Preliminary Design Documentation ...........................................................................................16
6.3.
Detailed Design Documentation ................................................................................................17
6.4.
Installation Documentation ........................................................................................................18
6.5.
Contractor/Builder initiated DAS ................................................................................................19
7
8.
ATTACHMENT-A: DAS INSTALLATION INSTRUCTIONS ................................................................22
8.1.
Passive Backbone .....................................................................................................................22
8.2.
Active Backbone ........................................................................................................................23
8.3.
Floor Cabling .............................................................................................................................23
8.3.1.
Feeder Cable Mounting (non radiating cable) ...................................................................23
8.3.2.
Radiating Cable Mounting ..................................................................................................24
8.3.3.
Mounting of Omni Antennas ..............................................................................................24
8.3.4.
Mounting of Panel Antennas ..............................................................................................25
533569390
Page 3 of 43
8.3.5.
9.
Other Arrangements ..........................................................................................................25
ATTACHMENT-B: TEST RESULTS – PASSIVE DAS ........................................................................27
9.1.
RF Sweeps ................................................................................................................................27
9.2.
Insertion Loss ............................................................................................................................27
9.3.
Passive Intermodulation Testing ...............................................................................................28
9.3.1.
533569390
Dynamic testing .................................................................................................................28
Page 4 of 43
1.
PURPOSE
Distributed Antenna Systems (DAS) are the in-building cabling, distribution and radiating
elements required for enhanced In-Building Coverage (IBC) for wireless services.
This specification outlines design and acceptance into service requirements for a DAS.
2.
SCOPE
This document applies to the design of IBC DAS to which a mobile telecommunications carrier
proposed to connect its equipment. Where capacity issues require a DAS to be sectorised within a
site, this document applies to each sector.
Clauses 5.3 and 5.5 should be used for mobile carrier design requirements for DASs built by other
operators.
3.
NOTES TO DESIGN & INSTALLATION CONTRACTORS
The RF design contractor shall develop all DAS Design Documentation in accordance with this
document
A DAS shall only be accepted into operation when the installation contractor verifies to one of the
licensed mobile carriers that the specifications defined in this document are met.
4.
OHS&E ISSUES
Issues of RF radiation hazards are included in the design process.
This DAS Design Specification Document does not override any general or project specific
OHS&E requirements. Where there seems to be a contradiction, more stringent requirement
should be applicable until the issue is discussed and resolved among “Sharing Carriers”.
5.
DESIGN SPECIFICATION
5.1. General DAS Description
The Distributed Antenna System (DAS) may be either passive:
typically composed of standard and radiating coaxial cables in various diameters (such as
3/8”, 1/2”, 7/8”, etc.), couplers and power splitters which are employed to branch the base
station power to indoor type omni and/or panel antennas in remote locations;
or active:
typically composed of point-to-point optical fibre cables connecting one or more local fibreoptic interfaces located in the base station to one or more AC or DC power operated active
heads in remote locations. The remote active heads in turn are each connected to one or
533569390
Page 5 of 43
more antennas, possibly via an additional amplifier.
In some cases the DAS can be hybrid, i.e. having both passive and active DAS segments.
In a DAS, RF signal is transmitted in both directions (uplink from mobile towards a base station,
and downlink from a base station towards a mobile).
5.1.1. Passive DAS
A passive DAS is typically divided into two main components:
•
the backbone feed system which forms the distribution to each floor or area; and
•
the floor/area cabling.
The backbone is generally composed of cables, splitters and couplers. The preferred network
topology is for groups of floors/areas (up to 4) to be fed from a multi-way splitter, which in turn is
fed from a trunk cable from the BTS (or from a higher level splitter where there are more than 4
floors/areas).
The floor cabling can be a combination of any of radiating cable, coaxial cable, fibre-optic remote
heads, antennae and terminations.
5.1.2. Active DAS
An active DAS typically has an interface unit which converts RF signals to optical signals. This
interface unit is typically co-located with the BTS equipment. Optical fibre distribution is used to
feed remote active heads which convert the optical signals back to RF signals which are then
connected to individual antennas or to a small passive distribution system.
Active systems may be multi-band, e.g. a tri-band system could have 3G850, DCS1800 and
3G2100 amplifiers in a common remote head.
5.2. Operating Frequency Bands
The radio equipment connected to the Distributed Antenna System shall operate in the 800/900
MHz bands (825 – 960 MHz), 1800 MHz band (1710 – 1880 MHz) and the 2100 MHz band (1910
– 2170 MHz) in accordance with the relevant ITU, ETSI and 3GPP specifications.
ACMA is considering release of 2500 ~ 2690 MHz band for LTE deployment.
The design shall generally specify the use of components which operate over the frequency range
825 – 960 and 1710 - 2170 MHz. Antennas and radiating cable shall operate over the frequency
ranges 825 – 960 and 1710 –2690 MHz.
5.2.1. Alternative frequency ranges
Where provision is required for non-cellular services, specify components that cover the required
frequency range.
When a DAS is required to carry wireless LAN signals (Wi-Fi or IEEE 802.11 at 2.4 GHz),
533569390
Page 6 of 43
designers shall comply with DCRB029.
If coverage of Mobile TV or UHF private mobile radio systems is needed, specify components
which cover the 380 – 2200 MHz range. Note that this requirement is incompatible with provision
for wireless LAN at 2.4 GHz.
If coverage of Mobile TV (700 MHz Band) or UHF private mobile radio (400 MHz Band) systems
is needed, specify components which cover the required additional bands which may extend to 380
– 820 MHz range.
5.3. DAS Capability
5.3.1. Passive DAS
Generally a passive DAS shall be capable of simultaneous operation of 3G850, GSM900/UMTS
900, GSM1800 and 3G2100 radio systems in accordance with Table 5-1. Where there are other
“Sharing Carriers” with different requirements, these different requirements need to be considered
among “Sharing Carriers” to establish an agreed DAS design specification prior to start of any
DAS design work.
Technology
No of RF
channels
Maximum input power per channel in the
system
GSM900/UMTS900
9
+40 dBm
GSM1800
9
+40 dBm
3G850
4
+40 dBm (+30 dBm CPICH power)
3G2100
8
+40 dBm (+30 dBm CPICH power)
Table 5-1 DAS capability requirements
5.3.2. Active DAS
The number of sharing Carriers and the number of channels per Carrier in each frequency band
shall be established prior to the commencement of the design.
The design shall assume that all channels in every frequency band are in operation simultaneously
and at maximum forward power.
5.4. Target Coverage Area
The Target Coverage Area shall be marked on copies of the site plan and floor plans and agreed
prior to commencement of the design.
5.5. RF Levels Required
Clauses 5.5.1 to 5.5.4 prescribe criteria for mobile station receive signal levels required at different
locations within buildings and outside the Target Coverage Area, to a confidence level of 95%.
These are minimum levels for In building Coverage DAS installations.
533569390
Page 7 of 43
When survey measurements show that the received power levels from nearby macro network base
stations are greater than the minimum levels specified for GSM900/ UMTS 900 and DCS1800,
and are greater than 6 dB below the minimum levels specified for 3G850 and 3G2100, obtain
confirmation and approval of the required IBC levels from a licensed mobile carrier engineer prior
to the commencement of the DAS design.
5.5.1. GSM900/UMTS 900
The design shall provide for GSM900/ UMTS900 at the following levels (received BCCH power
levels from a +40 dBm transmitter, measured with a unity gain omni antenna and achieve 95% of
the coverage objectives):
(a) > -65 dBm within 2 m of the perimeter walls and windows inside the premises;
(b) > -70 dBm in the building core;
(c) > -75 dBm in the basement car parks;
(d) < -90 dBm at ground level outside the building.
5.5.2. 3G850
The design shall provide for 3G850 at the following levels (received CPICH power levels from a
+40 dBm transmitter (+30 dBm CPICH power), measured with a unity gain omni antenna and
achieve 95% of the coverage objectives):
):
(a) > -85 dBm within 2 m of the perimeter walls and windows inside the premises;
(b) > -90 dBm in the building core;
(c) > -95 dBm in the basement car parks;
(d) < -110 dBm at ground level outside the building.
(e) Where ever possible a margin of at least 6dB above the existing macro cell coverage should
be used as a design target for all cases listed above.
5.5.3. DCS1800
The design shall provide for DCS1800 at the following levels (received BCCH power levels from
a +40 dBm transmitter, measured with a unity gain omni antenna and achieve 95% of the coverage
objectives):
):
(a) > -75 dBm within 2 m of the perimeter walls and windows inside the premises;
(b) > -80 dBm in the building core;
(c) > -85 dBm in the basement car parks;
(d) < -100 dBm at ground level outside the building.
5.5.4. 3G2100
The design shall provide for 3G2100 at the following levels (received CPICH power levels from a
+40 dBm transmitter (+30 dBm CPICH power), measured with a unity gain omni antenna and
achieve 95% of the coverage objectives):
533569390
Page 8 of 43
:
(a) > -85 dBm within 2 m of the perimeter walls and windows inside the premises;
(b) > -90 dBm in the building core;
(c) > -95 dBm in the basement car parks;
(d) < -110 dBm at ground level outside the building.
(e) Where ever possible a margin of at least 6dB above the existing macro cell coverage should
be used as a design target for all cases listed above.
5.6. Handover Zone
RF levels shall be sufficient to facilitate both-way handovers with the external network at locations
agreed on the target Coverage Area.
Handovers to/from external fast moving mobiles need to be avoided (except in tunnels). The
design should ensure that RF levels specified in clause 6.5 at ground level outside the building are
met.
5.7. DAS Configuration
The DAS shall be passive wherever possible utilising the RF power of the base stations to the
fullest possible extent. Active DAS sections shall be included only if there are installation
constraints, or available RF power is not sufficient.
Access to the DAS ports shall be from a communications room with sufficient accommodation for
the base station and network transmission equipment.
The design shall satisfy the installation requirements specified in Attachment A.
The distribution for each floor in a multi-storey building shall commence in a common
communications riser shaft.
5.7.1. Passive DAS Interconnect Ports
Provide four duplex ports to the DAS for multi-Carrier sharing. Each port shall be capable of
accepting up to 80 W composite transmit power, with a maximum power of 10 W per individual
channel (e.g. 8 x 10 W into each of the 4 inputs, at Measurement point 1 in Figure 5-1).
533569390
Page 9 of 43
5.7.2. Active DAS Interconnect Ports
Provide a duplex port for each sharing Carrier for each frequency band which that Carrier has
notified as a requirement.
5.8. Radiated Power Levels
The composite input power to any antenna in a DAS shall not exceed +17 dBm per Sharing
Carrier without approval.
In no case shall the combined power level from all transmitters cause the power density to exceed
the ARPANSA General Public power flux density (“Maximum exposure levels to radio frequency
fields – 3 kHz to 300 GHz”, Radiation Protection Series No. 3, Australian Radiation Protection
and Nuclear Safety Agency.) within 100 mm of any antenna.
To prevent interference to other existing equipment, the electric field strength shall not exceed 3
V/m, measured at a location nearest to the equipment under consideration.
5.8.1. Passive DAS
Assume a configuration of 4 operators each feeding 80 W composite power at 900 MHz into the
multi-network combiner when assessing radiated power levels for this clause.
If any Carrier is licensed for UMTS only, the power into each antenna may be calculated assuming
that the port occupied by the UMTS-only Carrier is fed with 80 W at 2100 MHz.
When 3G2100 channels are coupled to the DAS at an input other than the multi-network combiner
(e.g. at a cross-band coupler in the riser of a high-rise DAS), assume a maximum of 8 x 10 W
channels (at 2100 MHz) inserted at that input when assessing radiated power levels.
533569390
Page 10 of 43
5.8.2. Active DAS
Assume that all active devices connected to an antenna are operating at their maximum rated
composite output power per frequency band.
5.9. Electromagnetic Immunity
Designers shall ensure that the field strength levels in Table 5-2 are not exceeded in the areas or at
the equipment locations specified.
Equipment or
Location
Area
Field
strength
limit
Hospitals
Critical care medical equipment
1 V/m rms
Institutions for the
Hearing Impaired
1 V/m rms
Domestic Equipment
Location of domestic electrical equipment, e.g.
radio & television receivers, IT equipment.
3 V/m rms
Explosives and Fuel
Electro explosive devices – quarries, blasting
sites. Military – consult TRL. Petroleum or
aviation gas fuel sites.
9 V/m rms
Table 5-2 EMI Limits
As a guide, Table 5-3 indicates the distances from an antenna that the 1, 3 and 9 V/m electric field
strength limits are reached (to within 0.1 m). Note that, for a given EIRP, the electric field strength
at a given distance is independent of frequency and varies linearly with distance.
533569390
Input power to antenna
(dBm)
Antenna gain
(dBi)
Distance
Electric field strength
(V/m)
+23
3
3.5
0.99
+23
3
1.2
2.89
+23
3
0.4
8.68
+23
6
4.9
1.00
+23
6
1.7
2.89
+23
6
0.6
8.18
+23
9
7.0
0.99
+23
9
2.3
3.01
+23
9
0.8
8.66
+23
12
9.8
1.00
+23
12
3.3
2.97
+23
12
1.1
8.90
Page 11 of 43
Table 5-3 Distance from antenna for E field limits
5.10. Base Station Power Levels
The design of a passive DAS shall assume a maximum of 10 W (+40 dBm) per channel for
3G850, GSM900, GSM1800 and UMTS2100 in the downlink direction at the DAS port (multinetwork combiner input) for the power budget, maximum signal level and EMI calculations.
Ensure that the power levels at MNC input ports do not exceed the maximum of +40 dBm per
channel by inserting appropriate attenuators if needed.
5.11. Maximum Signal Received by MS/UE
The maximum signal levels received by a MS or UE situated as close as possible to any antenna
while being 1.5 m above floor level shall be in accordance with the table below (GSM05.05 Clause
6.1 for GSM900 & DCS1800, 3GPP TS25.101 Clause 7.4 for 3G2100 and 3G850).
Technology
Maximum received power
GSM900
-15 dBm/200 kHz
DCS1800
-23 dBm/200 kHz
3G850
-25 dBm/3.84 MHz
3G2100
-25 dBm/3.84 MHz
Table 5-4 Maximum received levels at MS/UE
Note that for a passive DAS the minimum path loss is determined by the maximum allowable
levels at the BTS receiver inputs, see 6.12.
5.12. Minimum Allowable Path Loss
5.12.1. Passive DAS
To avoid overloading of BTS receivers by uncontrolled MS/UE operating on adjacent channels
(GSM05.05 Clause 5.1 for GSM900 & DCS1800, 3GPP TS25.104 Clauses 7.3.2 & 7.4.1 for
3G2100 and 3G850), or by controlled MS/UE operating on a wanted channel at minimum transmit
power, the minimum path loss from the input to the multi-network combiner to a MS/UE situated
as close as possible to any antenna while being 1.5 m above floor level shall be in accordance with
the table below.
533569390
Technology
MS/UE Tx
Power
Maximum BTS
received power
Minimum path
loss
GSM900
+33 dBm
-26 dBm/200 kHz
59 dB
+5 dBm
-40 dBm/200 kHz
Page 12 of 43
Adj.channel
Cochannel
DCS1800
3G850
3G2100
+36 dBm
-35 dBm/200 kHz
0 dBm
-40 dBm/200 kHz
+24 dBm
-52 dBm/3.84 MHz
-50 dBm
-73 dBm/3.84 MHz
+24 dBm
-52 dBm/3.84 MHz
-50 dBm
-73 dBm/3.84 MHz
71 dB
Adj.channel
Cochannel
76 dB
Adj.channel
Cochannel
76 dB
Adj.channel
Cochannel
Table 5-5 Minimum allowable path loss
5.12.2. Active DAS
Ensure that the Maximum BTS received power values of Table 5-5 are complied with.
Ensure that the maximum uplink input signal levels at the remote units do not exceed the
manufacturer’s ratings.
5.13. Propagation Model
This document does not specify a propagation model as it is up to the DAS design vendor to
ensure that sufficient margins are provided, so that the minimum signal levels specified in this
document are delivered by the designed system once it is in operation.
5.14. Measured performance of installed DAS
In addition to the coverage, power and loss specifications above, a passive DAS shall meet the
following performance requirements.
5.14.1. Return loss
Return loss measured at any input port of the multi-network combiner (or any other device serving
a similar function) be greater than 20 dB over the operating frequency bands.
The return loss of any feeder connected to the output ports of the multi-network combiner shall be
greater than 16 dB over the operating frequency bands.
5.14.2. Passive intermodulation
The passive intermodulation performance of each passive DAS segment connecting to a multinetwork combiner (Measurement point 2 in Figure 5-1) shall be -140 dBc @ 2 x 43 dBm
minimum.
5.15. Cable and Component Labelling
533569390
Page 13 of 43
Specify labelling for installed cable and components as follows:
The horizontal runs of cable shall be labelled with a sticker at intervals of approximately 6 metres.
For vertical runs of cable, such as in risers, stickers shall be placed at approximately 1.8 m above
floor level on every floor.
These stickers shall also be attached on or close to each component. Stickers must not be placed on
the radiating element of the antenna or on the component identification plate. However stickers
should be placed on radiating cable.
All feeders should be identified at both feeder opening points with a label containing a concise
identification code uniquely identifying each cable and cross referenced to the system drawing.
Identification labels shall be provided by the contractor.
5.16. Preferred Material List
Refer to Attachment “C”. It is recommended that any third party developer seek
confirmation as to the currency of this Preferred Materials List from the MCF after twelve
(12) months from the date of issue of this document
5.17. Other Equipment Specifications
5.17.1. Characteristic impedance
RF circuit impedance of the system shall be 50-ohm unbalanced.
5.17.2. VSWR
VSWR measured at any base station input port shall not exceed 1.22:1 (corresponding to 16 dB
return loss) over the operating frequency bands.
5.17.3. Intermodulation
The passive intermodulation performance requirement for all components in the DAS beyond the
multi-network combiner shall be -140 dBc (with +43 dBm test signals) or better.
The minimum performance specification for any load (termination) connected to an unused output
port of a multi-network combiner shall be -140 dBc. The preferred configuration is for all output
ports to be connected to individual DAS segments. If this is not possible, specify low-IM cable
loads.
Specify that unused input ports of the multi-network combiner be terminated with 50 ohm/5 W
terminations. The maximum third-order intermodulation power produced by the termination shall
be -110 dBm when tested with 2 x +30 dBm CW test signals in the 900 MHz band.
5.17.4. Coaxial connector types
The multi-network combiner (Rojone ROJ-073), triband coupler (Filtronic CY076) and crossband
coupler (Rojone AMA-4255) are equipped with 7-16 DIN connectors. All cables connecting to
these devices shall use 7-16 DIN male connectors. Specify that approved torque wrenches be used
to tighten these connectors during construction and commissioning. All patch cables shall be fitted
with the required connector type. Inter-series adaptors shall not be used.
Beyond the multi-network combiner end of the first runs of backbone feeder cables, type-N
connectors may be used.
533569390
Page 14 of 43
As a rule of thumb:

Use 7/16 DIN Connectors for all high power connections (>= 1 watt), and thick cables (>=
1” in diameter).

Use N-Type Connectors for all low power connections (< 1 watt), and medium cables (<=
7/8” in diameter).
5.17.5. Patch cables
Do not use cables with any form of foil screening (eg Times Microwave LMR400) in the DAS.
Cables with foil screening have been found to have poor intermodulation performance regardless
of the quality of the connector terminations.
Existing DASs may contain LMR400 jumper cables. These cables should only be used in sections
of the DAS where the power is below +20 dBm/channel. They should also be fitted with a label
warning that they should not be used at power levels greater than +20 dBm/channel.
Many older DASs will contain jumper cables which are not labelled and do not meet the
intermodulation requirements of this Specification.
Where an existing DAS is being upgraded or extended, designers shall check for the presence of
sub-standard jumper cables and specify that they be replaced in those sections where the power
levels are > +20 dBm/channel, and fitted with a label elsewhere.
5.17.5.1.
Corrugated cable
Note that only patch cables with solid outer are to be used for interconnections between the BTS
end of the main feeders and the BTS antenna (Tx/Rx) ports.
Factory assembled patch cables shall be specified with the following minimum performance
parameters:
VSWR: 1:1.10 minimum over the frequency range 820 – 2690 MHz
Intermodulation performance: better than -150 dBc, static and dynamic measurements between
820 and 2690 MHz.
Connectors: DIN 7-16 or type-N, as required. Patch cable connectors shall mate with equipment
connectors and fixed cables without requiring joiners or inter-series adaptors.
5.17.5.2.
Braided cable5
Braided cable (RG214, etc.) shall not be used in passive distributed antenna systems.
Some active distributed antenna systems specify use of braided cables (RG59, RG6, RG11, etc.),
or CAT-5/CAT-6 wiring. They can be deployed providing they meet the following minimum
performance parameters:
VSWR: 1:1.15 minimum over the frequency range 820 – 2690 MHz
Intermodulation performance: better than -150 dBc @ 2 x 43 dBm, static and dynamic
measurements between 820 and 2690 MHz.
Connectors: Type-N, or as required. These connectors shall mate with equipment connectors and
other corrugated cable connectors without requiring joiners or inter-series adaptors.
6.
DELIVERABLES
533569390
Page 15 of 43
6.1. Documentation
All documentation shall be securely bound in a durable cover and in a form that allows easy
replacement and addition of individual sheets. The design contractor shall provide two sets of all
documentation supplied to the lead mobile carrier and any other sharing carriers.
In addition, soft copy of all drawings and documents supplied above are to be provided on a CD.
The documents shall be provided in formats compatible with Microsoft Office 2003 applications.
Drawings shall be in Acrobat .PDF format. (MS Visio or AutoCad drawing format if requested.)
All scanned drawings are to be stored in JPEG Bitmap format (*.JPG) or Acrobat .PDF format.
The design contractor shall provide two copies of the CD containing electronic copies of all
documentation supplied.
The design contractor shall provide Detailed Design Documentation and Turn-key Installation
Documentation.
6.2. Preliminary Design Documentation
Provide preliminary design documentation containing design related information and
drawings to a licensed mobile carrier for confirmation of design acceptability prior to
progression to detailed design.
(a)
533569390
design survey results;
(1)
existing coverage levels, conducted on street level to evaluate handover
requirement;
(2)
existing coverage levels , conducted on a medium floor and a high floor to
evaluate interference;
(3)
propagation study to characterise loss between consecutive floors in a high rise
building;
(4)
propagation study to characterise loss between an antenna in lift lobby and a
mobile inside a lift car when lift door is closed, both at the same level;
(b)
a description of the proposed design concept;
(c)
system schematic diagram;
(d)
power budget calculations for a single RF carrier in 3G850, GSM900, GSM1800 and
3G2100 frequency bands;
(e)
composite power calculated at each antenna port to demonstrate compliance with Clause
5.8;
(f)
propagation calculations demonstrating that RF levels predicted are in accordance with
Clause 5.5;
(g)
bill of materials (excluding installation materials);
Page 16 of 43
6.3.
Detailed Design Documentation
Provide detailed design documentation containing design related information and drawings
to a licensed mobile carrier for confirmation of detailed design acceptability prior to
progression installation.
.
a)
533569390
Design survey results:
(1)
existing coverage levels, conducted on street level to evaluate handover
requirement;
(2)
existing coverage levels, conducted on a medium floor and a high floor to
evaluate interference; These surveys should be conducted and plotted as a snail
trail overlayed on top of the floor plans. (RSCP and Ec/Io plots should both be
collected for WCDMA 850 and 2100 MHz).
(3)
propagation study to characterise loss between consecutive floors in a high rise
building;
(4)
propagation study to characterise loss between an antenna in lift lobby and a
mobile inside a lift car when lift door is closed, both at the same level.
b)
System description.
c)
System schematic diagram.
d)
Backbone distribution description.
e)
Floor layout description (for each floor unless identical).
f)
Equipment location and room details including access details, layout diagram/schematic
showing BTS positions.
g)
Actual photos of the equipment room and the active remotes (if present).
h)
Calculations:
(1)
power budget calculations for a single RF carrier in 3G850, GSM1800, and
3G2100 frequency bands;
(2)
composite power calculated at each antenna port to demonstrate compliance
with clause 5.8;
(3)
propagation calculations demonstrating that RF levels predicted are in
accordance with clause 5.5.
i)
Prediction printouts.
j)
UL/DL Attenuation setting for all the remotes to ensure that the max. remote output is
achieved at the max Admission control limit of MCPA (44.84 dBm). It needs to be clear
that all services being supported by the active DAS need to be considered to the extent of
the agreed number of channels for each technology.
k)
Manufacturer’s specification for all relevant equipment and material (power splitters,
directional couplers, antennas, standard feeder cables, radiating coaxial cables, etc.).
l)
Bill of materials (excluding installation materials), referring to Carriers PSAs where
Page 17 of 43
applicable.
m)
Certificate of Compliance stating that there are no RF radiation hazards, suitable for
uploading to the National Site Archive.
6.4. Installation Documentation
Provide installation related information and drawings, sufficient for installation.
a)
b)
Instructions for installation of the design:
(1)
antenna mounting instructions;
(2)
floor cable mounting instructions;
(3)
communications riser cabling instructions;
(4)
equipment room cabling instructions;
(5)
cable handling instructions;
(6)
cable labelling instructions.
Drawings:
(1)
DAS system schematic;
(2)
floor layout for every floor;
Floor layout drawings, showing the cable runs and antenna placement on each
floor, shall be supplied by the contractor. These drawings should have sufficient
detail and landmarks shown, so that a person unfamiliar with the site should be
able to trace out the proposed cable run and show the proposed positions of
antennae and other components (couplers, splitters, etc.) without needing to
remove the tiles. Where applicable, the floor plan should also show preferred
cable entry/exit points.
The drawing will be prepared in accordance with Australia Standards and
recommendations (e.g.1:100 scale), with at least 5 layers as follows:
•
•
•
•
•
(3)
drawing title, boundary, etc.
structural walls, lift cores, permanent brick or block partition walls, etc.
semi-permanent office partition walls (of plasterboard, glass, etc.) of full
height to ceiling level. Other partitions, such as workstation partitions, may
be omitted
proposed cable, component, and equipment design details
proposed cable, component, and equipment label designation
backbone distribution layout;
The drawing will be prepared in accordance with Australia Standards and
recommendations (e.g.1:50 scale), with at least 5 layers as follows:
•
•
•
533569390
drawing title, boundary, etc.
structural details and existing riser details, such as existing cable ladders,
large pipes, etc., which are significant;
proposed cable ladders for DAS backbone
Page 18 of 43
•
•
(4)
proposed cable, component, and equipment design details
proposed cable, component, and equipment label designation
installation details for non-standard cable and component installation.
c)
Bill of material (including installation materials).
d)
All aspects of civil engineering design work (if required) including the following:
e)
(1)
the structural design of the antenna support structures;
(2)
any other structural calculations or designs.
Specifications and instructions relevant to cabling, wiring and termination work of the RF
feeders, optical fibre cables, power wiring, and earth connections including:
(1)
assembling of parts;
(2)
fitting of connectors;
(3)
any other information that may fall within this category.
f)
Specification of AC power outlets for all AC powered equipment specified in DAS.
g)
Design and specification of the protective earth systems including lightning finials on the
antenna support structures for all externally installed antennas; the RF cable shall be
connected to earth just after entry into the BTS room if it is exposed to external
environment.
h)
Testing and commissioning specification and procedure of the Distributed Antenna
System, and data recording sheets (refer to Appendix C), including:
i)
(1)
RF sweeps;
(2)
RF power measured at the designated test points;
(3)
calculated line loss wrt the reference point;
(4)
passive intermodulation testing;
(5)
all alarm indications of the supervisory system (if applicable) to demonstrate
that they are operational to the manufacturer’s specification.
A list of the required spares (the type and quantity of the spares) considered necessary
for the prompt and efficient repair of faults which might arise during the operational life
of the system. A 5% ratio is considered appropriate when there is no other applicable
guideline.
6.5. Contractor/Builder initiated DAS
If the Builder has asked a contractor to design a DAS and the Contractor seeks a licensed mobile
carrier to take over optimisation and maintenance of the DAS, then the following information
should be provided by the contractor along with the detailed DAS design.
a)
Location and physical size (sq m) of the building.
b) Number of levels in the building and the ones being covered by the DAS.
c)
Breakdown of tenants if available.
d) Maximum number of people expected in the building at peak time.
533569390
Page 19 of 43
e)
Type of DAS – Passive, Active or Hybrid.
f)
Sectorisation plan for capacity management.
g) Identify high capacity service requirements if known eg: if some tenants want to have a
wireless office.
h) Technology being catered for (especially in an Active system) and the number of RF carriers
the link budget is designed for.
i)
Identify any spectrum limitation on the 2100 MHz active system.
j)
Ensure coverage requirements as specified in TCI0012 have been met for a 2100 MHz DAS.
k) Uplink / Downlink loading used in the link budget.
l)
Clearly identify if the DAS can achieve at least 6dB dominance over macro network on all
levels to ensure satisfactory data throughput, capacity and performance.
m) Proposed Soft HO areas once the DAS is ready with the outside macro network.
n) Commercial terms (who will fund the cost of the DAS?).
o) Any other relevant information available at the time.
7.
DEFINITIONS
The following words, acronyms and abbreviations are referred to in this document.
533569390
Term
Definition
ACMA
Australian Communication and Media Authority
Carrier
Licensed mobile telecommunications operator
Channel
Individual bearer, e.g. CDMA (1.23 MHz bandwidth), GSM & DCS (200 kHz
bandwidth) or UMTS (3.84 MHz bandwidth)
CW
Continuous Wave (i.e. unmodulated carrier)
IBC
In-Building Coverage
DAS
Distributed Antenna System
LTE
Long-Term Evolution
OH&S
Operational Health and safety
Operator
Alternative to ‘Carrier’, but specifically used in the context of the Lead
Carrier who is the Operator of a DAS.
RAN
Radio Access Network
RF
Radio Frequency
RND
Radio Network Development
SDB
Site Design Brief
Page 20 of 43
533569390
SEM
System Engineering Manager
SME
Subject Matter Expert
Page 21 of 43
8.
ATTACHMENT-A: DAS INSTALLATION GUIDELINES
Note that under no circumstances the following instructions to override
Building Codes of Australia. Where there is any conflict with the building
codes, installation contractor must follow Building Codes of Australia.
8.1. Passive Backbone
All backbone feeder cables shall run to the equipment room and be terminated with a DIN716
female connector. Wherever possible these cables shall be installed on the existing communication
cable trays between the equipment room and the communications riser. It shall be the design
contractor’s responsibility to ensure space is available. In the case of space not being available,
additional cable trays shall be specified.
Wherever possible, backbone feeder cables shall be installed on the existing cable ladder in the
communications riser. It shall be design contractor’s responsibility to ensure space is available. In
the case of space not being available additional cable ladder shall be specified.
All couplers and splitters specified in the backbone shall be mounted in an accessible location
inside the communications riser. All ports of these devices shall be connected through flexible
jumper cables to 1/2” or thicker feeder cables.
Figure 10-1 shows the layout of the backbone cable in a typical installation. The coupler shall be
located in a position that is uncluttered and with a view to future maintenance. Both the coupler
and cable should be secured to the riser wall or tray. Most couplers have holes to allow them to be
screwed to the wall but cable ties are acceptable. Jumper cables may be omitted from one port if
there is sufficient space to provide strain relief by putting a bend in a backbone cable.
Figure 10-1 Distribution from backbone cable
533569390
Page 22 of 43
All cabling in the riser shall be fixed neatly along the tray or to the wall with appropriate ties.
Fire-proof sealing shall be applied at all penetrations where a cable crosses boundary from one fire
control region to another, such as from a riser into a floor area. Watertight gland shall be employed
where necessary.
8.2. Active Backbone
Clause 10.1 is applicable, except fibre optic cables rather than RF feeder cables are used. Fibre
optic connectors shall be FC/APC type.
8.3. Floor Cabling
Cables run in the roof space may be strapped to the ceiling grid hangers in accordance with Figure
10-2, however this is not permitted by the Building Code of Australia if the hangers are only
designed to support the weight of the suspended ceiling and any associated light fittings. Make
sure that an approval explicitly authorising connection to ceiling grid hangers was obtained prior
to connecting any cable to these hangers.
8.3.1. Feeder Cable Mounting (non radiating cable)
The cable should be neatly fixed, taking the shortest possible path, to the ceiling grid hangers by
cable ties, allowing the maximum possible clearance above the ceiling tiles so as not to inhibit the
lifting of ceiling tiles for maintenance purposes. Cable ties should be placed at intervals of not
more than 2 metres.
Where connection to ceiling grid hangers are not permitted, cables has to be attached under
concrete slab at intervals of not more than 2 metres.
Figure 10-2 Floor cable mounting
533569390
Page 23 of 43
8.3.2. Radiating Cable Mounting
The cable should be neatly fixed to the ceiling grid hangers by cable ties, establishing a nominal
cable route of 6 m distance from the perimeter windows while taking the shortest possible path.
The cable should be run close to the ceiling tiles but above the lights and with enough clearance to
allow the tiles to be removed without hindrance. Cable ties should be placed at intervals of not
more than 2 metres.
Where connection to ceiling grid hangers are not permitted, radiating cables has to be attached to
messenger wires or directly under concrete slab at intervals of not more than 2 metres, in
accordance with its manufacturer’s instructions.
As with any radiating component, radiating cable should not be run near metal objects. It is not a
problem to run the cable past metal objects or to cable tie it to metal objects as long as the cable
and object traverse each other and do not run together longitudinally. If the cable needs to be run
along a metal object such as an air-conditioning duct it should be kept at least 100 mm off the
object. Similarly the cable should be installed using self-locking hangers with standoff accessory if
it is required to be installed on a concrete or metal surface. Various other methods are also
possible, such as using messenger cables. The Contractor shall ensure that cable manufacturers’
installation requirements are met in the Design Documentation to obtain the specified cable
performance. In particular, ensure that any instructions regarding the cable directivity are passed
on to the installation contractor (e.g. to align the cable in accordance with a mark on the cable
sheath).
Figure 10-3 Mounting radiating cable in ceiling space
The radiating cable (at the riser end) will be terminated with a type-N female connector.
This arrangement is valid for all floors with non-metallic ceiling tiles. If the ceiling tiles are
metallic, then no radiating cable should be installed in the ceiling space, and antennas must be
installed in accordance with clause 10.3.5
8.3.3. Mounting of Omni Antennas
The space around the antenna (including the ceiling space) should be as clear of metal objects as
possible to minimise the generation of intermodulation products and prevent distortion of the
radiation pattern. Ideally, there should be no metal objects within 600 mm of the antenna. In
533569390
Page 24 of 43
practice, locate centrally in or on a ceiling tile to maximise the spacing from the supporting grid
and place as far as possible from ductwork, cable trays, etc.
Specify installation of omnidirectional antennas on the underside of the ceiling wherever possible.
Where it is not possible to install antennas on the underside of the ceiling (eg due to a restriction
imposed by building owner or architect), install the antenna within the ceiling space.
Specify minimum spacings in accordance with Figure 10-4.
Figure 10-4 Minimum clearance for omnidirectional antennas
The design contractor shall ensure that any propagation losses through the ceiling tiles are
measured and taken into account during the design process.
8.3.4. Mounting of Panel Antennas
The panel antenna is a directional antenna. It shall be mounted away from metal surfaces to
minimise the generation of intermodulation products and prevent distortion of the radiation
pattern. There shall be no metal objects within 1.2 m of the front of the antenna.
Specify installation of panel antennas on a wall or on the underside of the ceiling wherever
possible.
The antenna should be mounted at least 170 mm above the plasterboard if installed in the ceiling
space.
8.3.5. Other Arrangements
The methods described above are suitable for ceilings with acoustic ceiling tiles. However where
metal tiles are used, the use of radiating coaxial cables is not possible. In this case antennas shall
be installed below the ceiling tiles.
See Figure 10-5 for details. Ensure that the metal groundplane of the antenna is insulated from the
metal ceiling tiles, by using an insulating disc or insulated standoffs or, in some cases, the radome
of the antenna may provide an effective stand-off if it wraps sufficiently over the edge of the
groundplane.
Antennas which have a non-metallic securing nut are preferred in this situation. When screws are
required to secure the antenna to the ceiling, use non-metallic screws, nuts and washers (nylon or
533569390
Page 25 of 43
similar).
Figure 10-5 Mounting omnidirectional antenna under metal ceiling tiles
533569390
Page 26 of 43
9.
ATTACHMENT-B: TEST RESULTS – PASSIVE DAS
9.1. RF Sweeps
All RF sweeps are to be documented as per the diagram below with the cable number and also
supplied in electronic format to the lead carrier for validation and acceptance.
All cables are to be swept across the 820 MHz to 960 MHz and 1710 to 2170 MHz bands.
R/4/2
9.2. Insertion Loss
The backbone distribution system must be checked for its insertion loss. A signal must be fed in at
the base station end and the level out must be measured at the final splitting or coupling point to
each floor. Where a splitter feeds more than 1 floor or there is more than 1 output from the same
splitter to a floor only one output needs to be tested. The difference between the input level and the
output level must be recorded as the insertion loss.
All measurements for insertion loss must be tabulated as per the example below and supplied in
electronic format to the lead carrier for validation and acceptance:
533569390
Test Point
Frequency
Input Point
Input Power
Output Power
Insertion Loss
Splitter S/3/1
860 MHz
BC/B2/1
+20 dBm
-3 dBm
23 dB
Page 27 of 43
Splitter S/11/1
860 MHz
BC/B2/1
+20 dBm
-7 dBm
9.3. Passive Intermodulation Testing
Passive intermodulation testing shall be carried out to determine the PIM performance of the
installed DAS. The test configuration shall be in accordance with Set-up 1 of IEC 62037, using
two +43 dBm test signals.
Testing in one frequency band is acceptable (e.g. 900 MHz only).
Test results shall be provided for reflected measurements at the following points:
•
Each input of the multi-network combiner
•
Each segment connected to multi-network combiner outputs (measured at the point which
connects to the multi-network combiner, ie including cable tails).
9.3.1. Dynamic testing
Where specifications call for dynamic testing (of cable assemblies), the cable under test shall be
bent through 90 degrees at its minimum bending radius, straightened, bent through 90 degrees and
straightened. The worst PIM performance observed during this sequence shall be recorded.
533569390
Page 28 of 43
27 dB
10. ATTACHMENT-C: PREFERRED MATERIALS LIST
The DAS developer should verify the suitability of any non preferred materials with the lead carrier prior to
incorporation in the DAS design and material purchase order
Antennas
533569390
Manufacturer
Model
Description
DrawCom
5052 300
Wideband Indoor Omni Antenna
Enersus
IDOVCB-0310-NFA
INDOOR OMNI ANTENNA, 8002500MHZ, 3DBI, N FEMALE
CONNECTOR W/ 1.0M PIGTAIL (3IM
COMPLIANT @ <-140DBC)
911/1129
Enersus
IDOVCB-0310NMA
INDOOR OMNI ANTENNA, 8002500MHZ, 3DBI, N MALE
CONNECTOR W/ 1.0M PIGTAIL (3IM
COMPLIANT @ <-140DBC)
911/1130
Enersus
IDPVCB-1010-NFA
INDOOR PANEL ANTENNA, 8002500MHZ, 10DBI, N FEMALE
CONNECTOR W/ 1.0M PIGTAIL AT
BOTTOM (3IM COMPLIANT @ <140DBC)
911/1131
Enersus
IDPVCB-1010NMA
INDOOR PANEL ANTENNA, 8002500MHZ, 10DBI, N MALE
CONNECTOR W/ 1.0M PIGTAILAT
BOTTOM (3IM COMPLIANT @ <140DBC)
911/1132
Enersus
IDPVCB-1010-NFB
INDOOR PANEL ANTENNA, 8002500MHZ, 10DBI, N FEMALE
CONNECTOR W/ 1.0M PIGTAIL AT
BACK (3IM COMPLIANT @ <140DBC)
911/1133
Enersus
IDPVCB-1010NMB
INDOOR PANEL ANTENNA, 8002500MHZ, 10DBI, N MALE
CONNECTOR W/ 1.0M PIGTAIL AT
BACK(3IM COMPLIANT @ <140DBC)
911/1134
Argus
CPA-1045V
3G850/GSM High Isolation Donor Panel
Antenna
Andrew
CELLMAX-O-25i
Wideband Indoor Omni Antenna
187/1045
Andrew
CELLMAX-D-25i
Wideband Indoor Panel Antenna
187/1046
Page 29 of 43
Ser/Item
Cables & Connectors
533569390
Manufacturer
Model
Description
Ser/Item
RFS
LCF12-50J
1/2" CELLFLEX® Low-Loss FoamDielectric Coaxial Cable
757/141
RFS
LCF78-50JA
7/8" CELLFLEX® Low-Loss FoamDielectric Coaxial Cable
757/142
RFS
LCF114S-50JA
1-1/4" CELLFLEX® Low-Loss FoamDielectric Coaxial Cable
757/143
RFS
LCF158-50JA
1-5/8" CELLFLEX® Low-Loss FoamDielectric Coaxial Cable
757/144
RFS
SCF12-50J
1/2" CELLFLEX® Superflexible FoamDielectric Coaxial Cable
NOT APPROVED FOR TAILS – USE
PREMADE TAILS.
757/145
RFS
716M-LCF12-070
7/16 DIN Male Connector for LCF12
cable
757/164
RFS
716F-LCF12-070
7/16 DIN Female Connector for LCF12
cable
757/353
RFS
NM-LCF12-070
N-type Male Connector for LCF12 cable
757/162
RFS
NF-LCF12-070
N-type Female Connector for LCF12
cable
757/163
RFS
716M-LCF78-074
7/16 DIN Male Connector for LCF78
cable
757/457
RFS
716F-LCF78-074
7/16 DIN Female Connector for LCF78
cable
757/458
RFS
NM-LCF78-074
N-type Male Connector for LCF78 cable
757/459
RFS
NF-LCF78-074
N-type Female Connector for LCF78
cable
757/460
RFS
716M-LCF114-072
7/16 DIN Male Connector for LCF114
cable
757/289
RFS
716F-LCF114-072
7/16 DIN Female Connector for LCF114
cable
757/290
RFS
716M-LCF158-072
7/16 DIN Male Connector for LCF158
cable
757/291
RFS
716F-LCF158-072
7/16 DIN Female Connector for LCF158
cable
757/292
RFS
716M-SCF12-070
7/16 DIN Male Connector for SCF12
cable
757/151
RFS
716F-SCF12-070
7/16 DIN Female Connector for SCF12
cable
757/352
RFS
NM-SCF12-070
N-type Male Connector for SCF12 cable
757/170
RFS
NF-SCF12-070
N-type Female Connector for SCF12
cable
757/171
RFS
7M7MS12-0100PS
SCF12 Jumper, DIN7-16 Male - DIN716 Male 1.0M
757/434
RFS
NMNMS12-0100PS
SCF12 Jumper, N Male – N Male 1.0M
757/384
Page 30 of 43
533569390
RFS
CABLE,COAX ASSEMBLY SCF38
3.0M 716M-716M
757/423
RFS
CABLE,COAX ASSEMBLY SCF38
3.0M 716M-716F
757/424
RFS
CABLE,COAX ASSEMBLY SCF38
3.0M 716M-NM
757/425
Andrew
VXL5-50
7/8” HELIAX® Low Density Foam
Very Flexible corrugated copper Coaxial
Cable in black PE jacket
757/409
Andrew
V5PDF
7/16 DIN Female Connector for VXL550 cable
757/411
Andrew
V5PDM
7/16 DIN Male Connector for VXL5-50
cable
757/410
Andrew
V5PNF
N-type Female Connector for VXL5-50
cable
757/413
Andrew
V5PNM
N-type Male Connector for VXL5-50
cable
757/412
Page 31 of 43
Filters
533569390
Manufacturer
Model
Description
Ser/Item
Triasx
CA721F8V2
DD GSM Filter Telstra band
187/888
Triasx
CA721F2V2
DD GSM Filter Optus band
187/723
Triasx
CA721F3V2
DD GSM Filter Vodafone band
187/724
Triasx
CA911F2V10
3G850-GSM900 combiner (40 dB
FA01/02) (DIN7-16 connectors)
187/890
Triasx
CA973F7V2
DD GSM Filter 891.6-915/936.6-960
MHz, for use with shared GSM900
active remote units.
187/tba
Triasx
CY076F1V1 (V2
and V3 versions may
also be used)
Triplexer 800-960/1710-1880/1920-2170
MHz
187/740
Triasx
DDF0014F1V1
Dual DDIMF (50 dB FA01/02/03), low
power, for use with Britecell/Ion-B
remote units
187/948
Ericsson
KRF 102 269/1
3G850 DDIMF (86 dB) to reduce
interference to GSM900
911/846
Triasx
DDF0022F1V1
3G850 DDIMF (60 dB FA01/02) to
reduce interference to GSM900
187/990
Triasx
DDF0021F1V1
3G850 DDIMF (86 dB FA02/03) to
reduce interference to GSM900
187/991
Triasx
DDF0035F1V1
3G850 DDIMF (86 dB FA01/02/03) to
reduce interference to GSM900
Microlab/FXR
BK-22
380-520 MHz / 800-960 MHz X-band
coupler
Microlab/FXR
BK-21
80-2170 MHz /2400-2500 MHz X-band
coupler
Page 32 of 43
Passive Components
533569390
Manufacturer
Model
Description
Ser/Item
Microlab/FXR
CM-A16
Multi-network combiner, 700-2700 MHz
187/917
Microlab/FXR
KM-A13
Multi-network combiner, 380-2500
MHz, rack-mounting
187/918
Microlab/FXR
D3-B48
3-way Power splitter, 500 W, -150 dBc,
DIN7-16
187/919
Rojone
AMA-1255-3HYB716
3 dB hybrid coupler
187/815
Rojone
ROJ-073-4-4-716
Multi-network combiner, 100 W, 8002200 MHz, -150 dBc
187/816
Rojone
AMA1255-03-1W
800-2500 MHz 3-dB 4-port directional
coupler
Rojone
AMA1255-06-1W
800-2500 MHz 6-dB 4-port directional
coupler
Rojone
AMA1255-08-1W
800-2500 MHz 8-dB 4-port directional
coupler
Rojone
AMA1255-10-1W
800-2500 MHz 10-dB 4-port directional
coupler
Rojone
AMA1255-13-1W
800-2500 MHz 13-dB 4-port directional
coupler
Rojone
AMA1255-17-1W
800-2500 MHz 17-dB 4-port directional
coupler
Rojone
AMA1255-20-1W
800-2500 MHz 20-dB 4-port directional
coupler
Rojone
AMA1255-30-1W
800-2500 MHz 30-dB 4-port directional
coupler
Rojone
AMA-2255-2N
800-2500 MHz 2-way Power Divider
Rojone
AMA-2255-3N
800-2500 MHz 3-way Power Divider
Rojone
AMA-2255-4N
800-2500 MHz 4-way Power Divider
Rojone
AMA-5240CL100W-30A
Cable load, 100 W low-IM
187/956
Andrew
C-6-CPUS-D
DIRECTIONAL COUPLER 6DB 8002500MHZ DIN
187/1027
Andrew
C-10-CPUS-D
DIRECTIONAL COUPLER 10DB 8002500MHZ DIN
187/1028
Andrew
C-6-CPUS-N
DIRECTIONAL COUPLER 6DB 8002500MHZ N
187/1029
Andrew
C-10-CPUS-N
DIRECTIONAL COUPLER 10DB 8002500MHZ N
187/1030
Andrew
C-15-CPUS-N
DIRECTIONAL COUPLER 15DB 8002500MHZ N
187/1031
Andrew
C-20-CPUS-N
DIRECTIONAL COUPLER 20DB 8002500MHZ N
187/1032
Page 33 of 43
533569390
Andrew
C-30-CPUS-N
DIRECTIONAL COUPLER 30DB 8002500MHZ N
187/1033
Andrew
S-2-CPUS-H-D
SPLITTER 2 -WAY HIGH POWER
800-2500 MHZ DIN
187/1034
Andrew
S-3-CPUS-H-D
SPLITTER 3 -WAY HIGH POWER
800-2500 MHZ DIN
187/1035
Andrew
S-4-CPUS-H-D
SPLITTER 4 -WAY HIGH POWER
800-2500 MHZ DIN
187/1036
Andrew
S-2-CPUS-H-N
SPLITTER 2 -WAY HIGH POWER
800-2500 MHZ N
187/1037
Andrew
S-3-CPUS-H-N
SPLITTER 3 -WAY HIGH POWER
800-2500 MHZ N
187/1038
Andrew
S-4-CPUS-H-N
SPLITTER 4 -WAY HIGH POWER
800-2500 MHZ N
187/1039
Andrew
S-2-CPUS-L-N
SPLITTER 2 -WAY LOW POWER 8002500 MHZ N
187/1040
Andrew
S-3-CPUS-L-N
SPLITTER 3 -WAY LOW POWER 8002500 MHZ N
187/1041
Andrew
S-4-CPUS-L-N
SPLITTER 4 -WAY LOW POWER 8002500 MHZ N
187/1042
Andrew
H-3-CPUS-D
3 DB HYBIRD COUPLER 800-2500
MHZ DIN
187/1043
Andrew
H-3-CPUS-N
3 DB HYBIRD COUPLER 800-2500
MHZ N
187/1044
Enersus
SPTCB-02M-NFA3IM
2 WAY MICROSTRIP SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1121
Enersus
SPTCB-03M-NFA3IM
3 WAY MICROSTRIP SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1122
Enersus
SPTCB-04M-NFA3IM
4 WAY MICROSTRIP SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1123
Enersus
SPTCB-02C-NFA3IM
2 WAY CAVITY SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
Enersus
SPTCB-03C-NFA3IM
3 WAY CAVITY SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
Enersus
SPTCB-04C-NFA3IM
4 WAY CAVITY SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
Page 34 of 43
IBC Off-Air Repeaters
Manufacturer
Model
Description
Andrew
MR853D
850 MHz UMTS Band-selective Mini
Repeater
Andrew
MR853D
REPEATER MR853D 10MHZ BASIC
ASSEMBLY
187/1011
Andrew
MR853D
REPEATER MR853D 15MHZ BASIC
ASSEMBLY
187/1012
Andrew
MR303D-6.6HR
900 MHz GSM Mini Repeater (6.6 MHz
band-width High Rejection)
Andrew
MR303D-6.6HR
REPEATER MR303D MINI
REPEATER 6.6MHZ
Andrew
MR301B
900 MHz GSM Band-selective Repeater
Andrew
MR301B
SERVICE,MR301B 6.6MHZ
CHANNEL CONV MOD
911/913
Andrew
MR301B
MODULE,MR301B 6.6MHZ
CHANNEL CONVERSION
911/912
Andrew
MR301BP
900 MHz GSM Band-selective Repeater
Andrew
MR301BP
REPEATER, MR301BP
911/914
Andrew
MR301BP
SERVICE,MR301BP 6.6MHZ
CHANNEL CONV MOD
911/930
Andrew
Node-M837
850 MHz UMTS RF Enhancer Repeater
Andrew
Node-M837
REPEATER NODE M837 48VDC
7517528-0005
187/1002
Andrew
Node-M837
REPEATER NODE M837 230VAC
7517528-0006
187/1003
Andrew
Mode-M843
850 MHz UMTS RF Enhancer Repeater
Andrew
Mode-M843
REPEATER NODE M843 48VDC
7517494-0006
187/0100
4
Andrew
Mode-M843
REPEATER NODE M843 230VAC
7517494-0007
187/0100
5
187/1010
Andrew
Ancillary equipment for the Andrew
Repeaters
Andrew
PSU KIT 230VAC FOR NODE M837
7516350
187/1023
Andrew
PSU SUIT MR303/MR853 AC IN 100240
187/1013
Andrew
REPEATER RF CABLE SMA/N
500MM 7513642
187/1018
850 MHz UMTS Micro ICS Repeater
System
767/135
Juni
533569390
Ser/Item
JI19-P800 Kit
(includes repeater,
modem, PS)
Page 35 of 43
IBC Fibre-Optic Repeater Systems
533569390
Manufacturer
Model
Description
Andrew
ION-M Series
ION-M Series Multi-Band MultiOperator Radio Over Fibre System
Andrew
ION-M Series
ION-M REMOTE 850 INCL CPD
TRIBAND CAB
187/1092
Andrew
ION-M Series
ION-M REMOTE 850/2100 INCL CPD.
TRI CAB
187/1093
Andrew
ION-M Series
ION-M REMOTE 850/1800/2100 INCL
CPD
187/1094
Andrew
ION-M Series
ION-M REMOTE 850 L CABINET
187/1095
Andrew
ION-M Series
ION-M REMOTE 850 L CABINET
INCL CPD
187/1096
Andrew
ION-M Series
ION-M OPTICAL MASTER BASE
UNIT ASSEMBLE
187/1097
Andrew
ION-M Series
ION-M OTRX 8-9/18/21 MU-LS
187/1098
Andrew
ION-M Series
ION-M OPTICAL COUPLER 2-WAY
E2000 1310
187/1099
Andrew
ION-M Series
ION-M OPTICAL COUPLER 4-WAY
E2000 1311
187/1100
Andrew
ION-M Series
ION-M SUBRACK 2 OTRX
187/1101
Andrew
ION-M Series
ION-M SUBRACK 3 OTRX, 370MM
187/1102
Andrew
ION-M Series
ION-M SUBRACK 4 OTRX
187/1103
Andrew
ION-M Series
ION-M SUBRACK 4 OTRX, 370MM
187/1104
Andrew
ION-M Series
ION-M SUBRACK UNIVERSAL
187/1105
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 806-824
851-869
187/1106
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 824-849
869-894
187/1107
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 876-880
921-925
187/1108
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 876-915
921-960
187/1109
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 880-915
925-960
187/1110
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 17101785 1805
187/1111
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 17101755 2110
187/1112
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 18501910 1930
187/1113
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 18501915 1930
187/1114
Andrew
ION-M Series
ION-M DUPLEXER PASSIVE 19201980 2110
187/1115
Page 36 of 43
Ser/Item
533569390
Andrew
ION-M Series
ION-M SPLITTER 2-WAY 870-2170
187/1116
Andrew
ION-M Series
ION-M SPLITTER 4-WAY 800-1000
187/1117
Andrew
ION-M Series
ION-M SPLITTER 4-WAY 1710-2170
187/1118
Andrew
ION-M Series
ION-M BTS CON. 3-PORT 0-2170
187/1119
Andrew
ION-M Series
ION-M BTS CON. 2-PORT 380-960 010DB
187/1120
Andrew
ION-M Series
ION-M BTS CONNECT 380-960
187/1121
Andrew
ION-M Series
ION-M BTS CON. 3-PORT 380-960
1710-2170
187/1122
Andrew
ION-M Series
ION-M BTS CON. 3-PORT 1710-2170
0-10DB
187/1123
Andrew
ION-M Series
ION-M BTS CON. 4-PORT 806-960
1710-2170
187/1124
Andrew
ION-M Series
ION-M BTS CON. 3-PORT 1710-1755
2110 AWS
187/1125
Andrew
ION-M Series
ION-M BTS CON. 3-PORT 1895-1910
1975 PCS
187/1126
Andrew
ION-M Series
ION-M BTS CON. 4-PORT 1710-2170
0-10DB
187/1127
Andrew
ION-M Series
ION-M BTS CON. 1-PORT 0-30DB
187/1128
Andrew
ION-M Series
ION-M BTS CON. 1-PORT 0-30DB
WITH SPLITT
187/1129
Andrew
ION-M Series
ION-M BTS CON. 2-WAY 851-869
187/1130
Andrew
ION-M Series
ION-M SPLITTER 4-WAY 380-960 010DB
187/1131
Andrew
ION-M Series
ION-M SPLITTER 4-WAY 1710-2170
0-10DB
187/1132
Andrew
ION-M Series
ION-M COMBINER 4-WAY 806-960
0-10DB
187/1133
Andrew
ION-M Series
ION-M COMBINER 4-WAY 1710-1990
0-10DB
187/1134
Andrew
ION-M Series
ION-M COMBINER 4-WAY 1920-2170
0-10DB
187/1135
Andrew
ION-M Series
ION-M ACT.COMB.W.IPP 4-WAY
880-960
187/1136
Andrew
ION-M Series
ION-M ACT.COMB.W.IPP 4-WAY
1710-1880
187/1137
Andrew
ION-M Series
ION-M ACT.COMB.W.IPP 4-WAY
1920-2170
187/1138
Andrew
ION-M Series
ION-M SPLITTER 3HU 2X4-WAY
806-960
187/1139
Andrew
ION-M Series
ION-M SPLITTER 1HU 3X4-WAY
806-960
187/1140
Andrew
ION-M Series
ION-M SPLITTER 1HU 3X4-WAY
806-960
187/1141
Andrew
ION-M Series
ION-M SPLITTER 1HU 2X4-WAY
187/1142
Page 37 of 43
806-960
533569390
Andrew
ION-M Series
ION-M SUBRACK 4 PSU DC 3HU
187/1143
Andrew
ION-M Series
ION-M SUBRACK 4 PSU AC 3HU
187/1144
Andrew
ION-M Series
ION-M SUBRACK 8 PSU DC 6HU
187/1145
Andrew
ION-M Series
ION-M SUBRACK 8 PSU AC 6HU
187/1146
Andrew
ION-M Series
ION-M POWER SUPPLY UNIT DC IN
48V
187/1147
Andrew
ION-M Series
ION-M POWER SUPPLY UNIT AC IN
100-240V
187/1148
Andrew
ION-M Series
ION-M MMC PLUS
187/1149
Andrew
ION-M Series
ION-M RMC MULTI-USER WITH
MODEM GSM 9/18
187/1150
Andrew
ION-M Series
ION-M RMC SINGLE-USER WITH
MODEM GSM
187/1151
Andrew
ION-M Series
ION-M RMC SINGLE-USER
WITHOUT MODEM
187/1152
Andrew
ION-M Series
ION-M RMC SINGLE-USER WITH
MODEM GSM
187/1153
Andrew
ION-M Series
ION-M DISPLAY & KEYBOARD
DRAWER 1HU 12V
187/1154
Andrew
ION-M Series
ION-M RACK ALARM BOARD
187/1155
Andrew
ION-M Series
ION-M SYSTEM ALARM BOARD
187/1156
Andrew
ION-M Series
ION-M FAN SET 4 FANS MU ROOF
MOUNT
187/1157
Andrew
ION-M Series
ION-M FAN 19" 1HU 12V DC
4312/17V
187/1158
Andrew
ION-M Series
ION-M HEATER
187/1159
Andrew
ION-M Series
ION-M UPS-KIT 230V
187/1160
Andrew
ION-M Series
ION-M MODEM KIT MC35 19" RF
FRONT
187/1161
Andrew
ION-M Series
ION-M SW OPTION USB IN RMC
DEACTIVATED
187/1162
Andrew
ION-M Series
ION-M SW OPTION WINDOWS
HARDENING
187/1163
Andrew
ION-M Series
ION-M LEVELING ADAPTER 6
PORTS
187/1164
Andrew
ION-M Series
ION-M RF PATCH CABLE
187/1165
Andrew
ION-M Series
ION-M DIR.COUPLER 380-480 20DB
187/1166
Andrew
ION-M Series
ION-M DIR.COUPLER 806-960 4DB
187/1167
Andrew
ION-M Series
ION-M TERMINATION 200W 4002200MHZ N FE
187/1168
Andrew
ION-M Series
ION-M RACK 19" 7 HU
187/1169
Andrew
ION-M Series
ION-M RACK 19" B 24 HU
187/1170
Andrew
ION-M Series
ION-M RACK 19" 33 HU OUTDOOR
187/1171
Page 38 of 43
533569390
Andrew
ION-M Series
ION-M RACK 19" B 38 HU
187/1172
Andrew
ION-M Series
ION-M PACKAGING 24 HU
187/1173
Andrew
ION-M Series
ION-M PACKAGING 33 HU
187/1174
Andrew
ION-M Series
ION-M PACKAGING 38 HU
187/1175
Andrew
ION-B Series
ION-M Series Multi-Band MultiOperator Radio Over Fibre System
Andrew
ION-B Series
ION-B REMOTE
EGSM/GSM18/UMTS, VAC, SC/AP
187/1176
Andrew
ION-B Series
ION-B REMOTE
EGSM/GSM18/UMTS, 48V, SC/APC
187/1177
Andrew
ION-B Series
ION-B REMOTE UMTS, VAC,
SC/APC, N-F, CASE-B
187/1178
Andrew
ION-B Series
ION-B REMOTEUMTS, -48VDC,
SC/APC, N-F, CASEB
187/1179
Andrew
ION-B Series
ION-B REMOTE
CELL850/GSM1800,VAC, SC/APC
187/1180
Andrew
ION-B Series
ION-B REMOTE CELL850/GSM1800,
-48VDC, SC
187/1181
Andrew
ION-B Series
ION-B REMOTE CELL850/UMTS,
VAC, SC/APC, N-F
187/1182
Andrew
ION-B Series
ION-B REMOTE CELL850/UMTS,
-48VDC, SC/APC
187/1183
Andrew
ION-B Series
ION-B REMOTE
CELL/DCS/UMTS,VAC,1RF,SC/AP
187/1184
Andrew
ION-B Series
ION-B REMOTE CELL/DCS/UMTS,
-48VDC, 1RF, SC
187/1185
Andrew
ION-B Series
ION-B REMOTE UMTS, VAC, 1RF,
SC/APC, N-F
187/1186
Andrew
ION-B Series
ION-B REMOTE UMTS,-48VDC, 1RF,
SC/APC, N-F
187/1187
Andrew
ION-B Series
ION-B SUBRACK, PASSIVE BP, 19"X
4HE
187/1188
Andrew
ION-B Series
ION-B SUBRACK, ACTIVE BP, 19"X
4HE
187/1189
Andrew
ION-B Series
ION-B SUBRACK, AC REDNT
PS,ACTV, 19"X4HE
187/1190
Andrew
ION-B Series
ION-B SUBRACK,-48VDC, ACTIVE
BP,19"X4HE
187/1191
Andrew
ION-B Series
ION-B MASTER OPTICAL RTX,
WIDEBAND, SC
187/1192
Andrew
ION-B Series
ION-B MASTER OPTICAL RTX,
400MHZ,SC/APC
187/1193
Andrew
ION-B Series
ION-B COMBINER, 8-1.0/1.7-2.5GHZ,
4HEX7T
187/1194
Andrew
ION-B Series
ION-B COMBINER,
LMR800/LMR900/PC S
187/1195
Andrew
ION-B Series
ION-B COMBINER, 8-1.0/1.71/1.92-
187/1196
Page 39 of 43
2.17GHZ
533569390
Andrew
ION-B Series
ION-B COMBINER, 81.0GHZ/AWS/PCS
187/1197
Andrew
ION-B Series
ION-B DPLX LMR800,SMAF,4HEX7TE
187/1198
Andrew
ION-B Series
ION-B DPLX CELL850,SMAF,4HEX7TE
187/1199
Andrew
ION-B Series
ION-B DPLX EGSM,SMA-F,4HEX7TE
187/1200
Andrew
ION-B Series
ION-B DPLX GSM1800,SMAF,4HEX7TE
187/1201
Andrew
ION-B Series
ION-B DPLX UMTS,SMA-F,4HEX7TE
187/1202
Andrew
ION-B Series
ION-B,2 VAR
ATT,10DB,4HEX7TE+2X20DB PADS
187/1203
Andrew
ION-B Series
ION-B,2 VAR ATTEN,30DB,4HEX7TE
187/1204
Andrew
ION-B Series
ION-B,2 WAY,700-2500MHZ,SMAF,4HEX7TE
187/1205
Andrew
ION-B Series
ION-B,4 WAY,700-2500MHZ,SMAF,4HEX7TE
187/1206
Andrew
ION-B Series
ION-B 900/1800MHZ POWER
LIMITER, 10DB
187/1207
Andrew
ION-B Series
ION-B UMTS POWER LIMITER,
10DB
187/1208
Andrew
ION-B Series
ION-B SUPERVISION,AC,19" X1HE X
300MM
187/1209
Andrew
ION-B Series
ION-B SUPERVISION,DC,19" X1HE X
300MM
187/1210
Andrew
ION-B Series
ION-B PLUG-IN SUPERVISION,
4HEX14TE
187/1211
Andrew
ION-B Series
ION-B, BLANK PANEL, 4HEX14TE
187/1212
Andrew
ION-B Series
ION-B TSUN MC35 MODEM KIT
187/1213
Andrew
ION-B Series
ION-B FAST MINIRACK
187/1214
Andrew
ION-B Series
ION-B FAST INTERFACE
187/1215
Andrew
ION-B Series
ION-B I/LINK
CELL/GSM900/GSM1800/UMTS,2F
187/1216
Andrew
ION-B Series
ION-B I/LINK
CELL/GSM900/GSM1800/UMTS,1F
187/1217
Andrew
ION-B Series
ION-B I/LINK
EGSM//GSM1800/UMTS,2F
187/1218
Andrew
ION-B Series
ION-B I/LINK
EGSM//GSM1800/UMTS,WDM,1F
187/1219
Andrew
ION-B Series
ION-B ACC PS, 12
REMOTE,1.0A,VAC TO-48,
187/1220
Andrew
ION-B Series
ION-B ACC PS, 12
REMOTE,1.0A,VAC TO-48,
187/1221
Andrew
ION-B Series
ION-B ACC PS, 12+1 OUT,2.0A,VAC
TO-48
187/1222
Page 40 of 43
533569390
Andrew
ION-B Series
ION-B ACC PS, 12+1 OUT,2.0A,48TO-48,19"
187/1223
Andrew
ION-B Series
ION-B ACC PS, 24 REMOTE, 1.0A, 48V
187/1224
Andrew
ION-B Series
ION-B ACC AC/DC PS MODULE,
600W
187/1225
Andrew
ION-B Series
ION-B ACC DC/DC PS MODULE,
600W
187/1226
Andrew
ION-B Series
ION-B ACC EXT PSU CASE B, 85-265
VAC/5
187/1227
Andrew
ION-B Series
ION-B ACC EXT PSU CASE B, 72 TO
36 VDC/5
187/1228
Andrew
ION-B Series
ION-B ACC EXT PSU R, 85-265
VAC/28VDC80W
187/1229
Andrew
ION-B Series
ION-B ACC EXT PSUR,72TO36VDC/28VDC80W
187/1230
Andrew
ION-B Series
ION-B ACC EXT PSUR2E,85265VAC/28VDC
187/1231
Andrew
ION-B Series
ION-B ACC EXT PSUR2E,-72TO36VDC/28VDC
187/1232
Andrew
ION-B Series
ION-B ACC EXT PSUR2E,85265VAC/55VDC
187/1233
Andrew
ION-B Series
ION-B INSTALLL
KIT,INDOOR,CASE B
187/1234
Andrew
ION-B Series
ION-B ACC WLAN LOCAL
INTERFACE, 3 AP
187/1235
Andrew
ION-B Series
ION-B ACC WLAN BOOSTER,2NFANTPORTS,VAC
187/0123
6
Andrew
ION-B Series
ION-B ACC WLAN BOOSTER,2NFANTPORTS,VAC
187/1237
Andrew
ION-B Series
ION-B ACC2G/3G & WI-FI
DIPLEXER
187/1238
Andrew
ION-B Series
ION-B ACC
TERMINATION,SMA0.06W,50OHM
187/1239
Andrew
ION-B Series
ION-B ACC
TERMINATION,SMA0.06W,50OHM
187/1240
Andrew
ION-B Series
ION-B ACC
SUBRACKSPLICEORGANISERUPTO
24
187/1241
Andrew
ION-B Series
ION-B
ACCUPPTO24CORES(ADAPTERSNO
TINCLUD)
187/1242
Andrew
ION-B Series
ION-B ACCADAPTERSC/APCSC/APC
187/1243
Andrew
ION-B Series
ION-B ACCOPTICALJUMPERSCAPCCONNT.2MT
187/1244
Andrew
ION-B Series
ION-B ACC SPLICING BOX
187/1245
Andrew
ION-B Series
ION-B ACC SPLICING BOX
187/1246
Page 41 of 43
533569390
Enersus
MA2000 Series
MA 2000 Converged In-building
Coverage System
Enersus
NMS-SW-SERVER
GUI AND SERVER S/W PACKAGE
(ONE PER SITE)
911/945
Enersus
410
NETWORK CONTROLLER - SERIAL
INTERFACE (DIAL-UP)
911/946
Enersus
430
NETWORK CONTROLLER ETHERNET/IP INTERFACE
911/947
Enersus
RIU-IM
RADIO INTERFACE UNIT
Enersus
RIU-BTSC-CELL
Enersus
RIU-BTSC-DCS
Enersus
RIU-BTSC-GSM
Enersus
RIU-BTSC-UMTS
Enersus
WB-B4U
Enersus
WB-B8U
Enersus
2000-MINI-ENC
2000 ENCLOSURE SUPPORTING 2
MODULES
911/955
Enersus
2000-CL-M-DCS-L
DUAL BAND CELL M.O /DCS 1
PORT FOR LITE
911/956
Enersus
2000-GSM-DCS-L
DUAL BAND GSM/DCS 1 PORT FOR
LITE
911/957
Enersus
1200-UMTS-AO-LT
ADD-ON RHU SUPPORTING UMTS
SERVICE FOR 2000 LITE
911/958
Enersus
2000-RC-LP
REMOTE CABINET ALL SERVICES
911/959
Enersus
2000-RC-RP
REMOTE CABINET - ALL
SERVICES, REMOTE POWERING
911/960
Enersus
860
WLAN MODULE SUPPORTING 1-4
AP 802.11A/B/G
911/961
Enersus
860-U
WLAN MODULE SUPPORTING 1-4
AP 802.11A/B/G INCLUDING UMTS
911/962
Enersus
AK-850-1200
ACCESSORY KIT FOR 850 WITH
1200
911/963
Enersus
AK-850-2000
ACCESSORY KIT FOR 850 WITH
2000
911/964
Enersus
LPS-48V-100W
LOCAL AC/DC CONVERTER 100W
911/965
Enersus
LPS-48V-40W
LOCAL AC/DC CONVERTER 40W
911/966
Enersus
LPS-48V-66W
LOCAL AC/DC CONVERTER 66W
911/967
Enersus
2000-CELL-DCSLT
M2000 LITE CELLULAR 800/DCS
1800 MODIFIED FOR TELSTRA
911/997
911/94
8
BTS CONDITIONER FOR CELLULAR 911/94
9
911/95
BTS CONDITIONER FOR DCS
1800MHZ
0
911/95
BTS CONDITIONER FOR GSM
900MHZ
1
911/95
BTS CONDITIONER FOR UMTS
2100MHZ
2
911/95
WIDE BAND BASE, 4 UNIT,
SUPPORTING 4 RHUS
3
911/95
WIDE BAND BASE, 8 UNIT,
SUPPORTING 8 RHUS
4
Page 42 of 43
Enersus
SPTCB-02M-NFA
2 WAY MICROSTRIP SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1121
Enersus
SPTCB-03M-NFA
3 WAY MICROSTRIP SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1122
Enersus
SPTCB-04M-NFA
4 WAY MICROSTRIP SPLITTER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1123
Enersus
COUCB-06M-NFA
6DB MICROSTRIP COUPLER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1124
Enersus
COUCB-10M-NFA
10DB MICROSTRIP COUPLER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1125
Enersus
COUCB-13M-NFA
13DB MICROSTRIP COUPLER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1126
Enersus
COUCB-15M-NFA
15DB MICROSTRIP COUPLER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1127
Enersus
COUCB-20M-NFA
20DB MICROSTRIP COUPLER, 8002500MHZ, N FEMALE CONNECTORS
(3IM COMPLIANT @ <-140DBC)
911/1128
Enersus
MA1000 Series
MA 1000 Converged In-building
Coverage System
The use of high quality RF connectors with gold or silver plating, or made of sucoplate, brass, or beryllium
copper is essential. RF connectors containing steel, nickel, or aluminium shall not be used.
Cables shall meet the requirements of relevant building codes, fire authorities and building owners/managers
in respect of fire retardant and smoke emission properties. In general, there is no specific requirement for
general office areas, but some buildings may require particular cable specifications.
If an existing DAS installation has fire retardant and low smoke emission cables, specify cables with
equivalent properties for any upgrade or extension of that DAS.
Specify cables with solid outer conductors (SCF38 or equivalent as a minimum requirement) between BTS
and multi-network combiner or crossband coupler, and between multi-network combiner and main feeders.
533569390
Page 43 of 43