Guardian Industries Corp.
2300 Harmon Road
Auburn Hills, Michigan 48326
Toll Free
(866) 482-7374
Web Sites
www.guardian.com, www.sunguardglass.com
November 2015
NOTICE: The guide specification on the following pages is designed to assist
architects and specification writers. It is provided as a guideline only. Guardian
Industries does not assume any responsibility for the suitability or applicability of this
guide specification to any specific building project.
Guide Specification in CSI 3-Part Format
SECTION 088100
INSULATING GLASS GLAZING
PART 1 - GENERAL
SUMMARY
A.
Section includes solar control coated insulating glass units.
B.
Related Sections:
Division 02-49 Sections specifying glass and glazing by reference to this Section.
Division 07 Section "Joint Sealants" for glazing sealants.
Division 08 Section "Decorative Glass Glazing" for decorative glass for interior applications.
Division 08 Section "Mirrors" for interior, unframed glass mirrors.
Division 08 Section "Plastic Glazing" for acrylic and polycarbonate glazing.
Division 08 Section "Security Glazing" for security applications.
Division 10 Section "Toilet, Bath, and Laundry Accessories" for metal-framed mirrors.
REFERENCES
C.
ASTM C 1036 - Standard Specification for Flat Glass.
D.
ASTM C 1048 - Standard Specification for Heat-Treated Flat Glass--Kind HS, Kind FT Coated
and Uncoated Glass.
E.
ASTM C 1376 - Standard Specification for Pyrolytic and Vacuum Deposition Coatings on
Glass.
F.
ASTM E 773 - Standard Test Method for Accelerated Weathering of Sealed Insulating Glass
Units.
G.
ASTM E 2190 - Standard Specification for Insulating Glass Unit Performance and Evaluation.
H.
CPSC 16CFR-1201 - Safety Standard for Architectural Glazing Materials.
088100 GLASS
Page 1 of 6
I.
GANA Glazing Manual.
DEFINITIONS
J.
Sealed Insulating Glass Unit Surfaces:
Surface No. 1: Exterior surface of outer lite.
Surface No. 2: Interior surface of outer lite.
Surface No. 3: Exterior surface of inner lite.
Surface No. 4: Interior surface of inner lite.
K.
Airspace: Space between lites of an insulating glass unit that contains dehydrated air or other
inert specified gas.
SUBMITTALS
L.
Comply with Division 01 Section "Submittal Procedures."
M.
Product Data: Submit manufacturer's product data, including performance characteristics and
installation instructions.
N.
Shop Drawings: Submit manufacturer's or fabricator's shop drawings, including plans,
elevations, sections, and details, indicating glass dimensions, tolerances, types, thicknesses, and
coatings.
O.
Samples: Submit manufacturer's samples of each type, thickness, and coating.
P.
Fabricator's Certification: Submit fabricator's certification by manufacturer.
Q.
Cleaning Instructions: Submit manufacturer's cleaning instructions.
R.
Warranty: Submit manufacturer's standard warranty for sealed insulating glass units.
QUALITY ASSURANCE
S.
Manufacturer's Qualifications: Minimum of 5 years experience manufacturing solar control
coated glass.
T.
Fabricator's Qualifications:
Minimum of 5 years experience manufacturing sealed insulating glass units meeting ASTM E
2190, Class CBA.
Certified by manufacturer.
U.
Mock-Ups:
Comply with Division 01 Section "Quality Control."
Obtain acceptance of mock-ups by Architect before proceeding with work.
DELIVERY, STORAGE, AND HANDLING
V.
Delivery:
088100 GLASS
Page 2 of 6
Deliver glass to site in accordance with manufacturer's instructions.
Deliver glass in manufacturer's or fabricator's original containers and packaging, with labels
clearly identifying product name and manufacturer.
W.
Storage:
Store glass in accordance with manufacturer's instructions.
Store glass in clean, dry area indoors.
Protect from exposure to direct sunlight and freezing temperatures.
Apply temporary coverings loosely to allow adequate ventilation.
Protect from contact with corrosive chemicals.
Avoid placement of glass edge on concrete, metal, and other hard objects.
Rest glass on clean, cushioned pads at 1/4-points.
X.
Handling:
Handle glass in accordance with manufacturer's instructions.
Protect glass from damage during handling and installation.
Do not slide one lite of glass against another.
Do not use sharp objects near unprotected glass.
WARRANTY
Y.
Manufacturer's Special Warranty on Insulating Glass: Manufacturer's standard form in which
insulating-glass manufacturer agrees to replace insulating-glass units that deteriorate within
specified warranty period. Deterioration of insulating glass is defined as failure of hermetic seal
under normal use that is not attributed to glass breakage or to maintaining and cleaning
insulating glass contrary to manufacturer's written instructions. Evidence of failure is the
obstruction of vision by dust, moisture, or film on interior surfaces of glass.
Warranty Period: [10] <Insert number> years from date of [manufacture].
PART 2 - PRODUCTS
MANUFACTURER
A.
Guardian Industries Corp., 2300 Harmon Road, Auburn Hills, Michigan 48326. Toll Free (866)
482-7374. Web Sites www.guardian.com, www.sunguardglass.com
B.
Substitutions:
Not permitted.
FABRICATORS
C.
D.
Sealed Insulating Glass Units, Heat-Strengthened Glass, Tempered Glass, and Spandrel Glass:
Acceptable Fabricators: Certified by glass manufacturer.
1.
________________________________________.
2.
________________________________________.
3.
________________________________________.
088100 GLASS
Page 3 of 6
SOLAR CONTROL INSULATING COATED GLASS
E.
Double-Glazed Sputter-Coated Insulating Glass Units:
Conformance: ASTM E 2190, Class CBA.
Outboard Lite:
Sputter-coated [clear] [low-iron] [green-tinted] [TwilightGreen®]
[CrystalGray®] [gray] float glass.
a.
Clear Float Glass: ASTM C 1036, Type I, Class 1, Quality q3.
b.
Tinted Float Glass: ASTM C 1036, Type I, Class 2, Quality q3.
c.
Vacuum Deposition Sputtered Coating: ASTM C 1376.
d.
Coating on Surface No. 2: [SunGuard AG 43] [SunGuard AG 50] [SunGuard
Silver 20] [SunGuard Neutral 40] [SunGuard Neutral 50] [SNX 51/23] [SNX
62/27] [SunGuard SN 68] [SunGuard SN 54] [SunGuard SNR 43] [SunGuard
Neutral 61] [Neutral 78/65] [none].
e.
Glass Thickness: [3 mm (1/8 inch)] [4 mm (5/32 inch)] [5 mm (3/16 inch)] [6 mm
(1/4 inch)] [8 mm (5/16 inch)].
f.
Heat Treatment:
[None] [Heat-strengthened, ASTM C 1048, Kind HS]
[Tempered; ASTM C 1048, Kind FT; CPSC 16CFR-1201].
Air Space: [6 mm (1/4 inch)] [12 mm (1/2 inch)] wide, hermetically sealed, dehydrated air
space.
Inboard Lite: [clear] [low-iron] float glass.
g.
Annealed Clear Float Glass: ASTM C 1036, Type I, Class 1, Quality q3.
h.
Vacuum Deposition Sputtered Coating: ASTM C 1376.
i.
Coating on No. 3 surface: [SNX 62/27] [SunGuard SN 68] [Neutral 78/65] [None].
j.
Glass Thickness: [3 mm (1/8 inch)] [4 mm (5/32 inch)] [5 mm (3/16 inch)] [6 mm
(1/4 inch)] [8 mm (5/16 inch)].
k.
Heat-Treatment:
[None] [Heat-strengthened, ASTM C 1048, Kind HS]
[Tempered;
ASTM
C
1048,
Kind
FT;
CPSC
16CFR-1201].
Glass Unit Performance Characteristics:
l.
Visible Light Transmittance: ________ percent.
m.
Visible Light Reflectance Outdoors: ________ percent.
n.
Direct Solar Energy Transmittance: ________ percent.
o.
Direct Solar Energy Reflectance Outdoors: ________ percent.
p.
Winter U-Value Nighttime: ________.
q.
Summer U-Value Daytime: ________.
r.
Shading Coefficient: ________.
s.
Solar Heat Gain Coefficient: ________.
t.
Summer Relative Heat Gain: ________.
Sealing System: Dual seal, approved by glass manufacturer, with [fabricator's standard]
[polyisobutylene and polysulfide] [polyisobutylene and silicone] [polyisobutylene
and hot-melt butyl] [polyisobutylene and polyurethane] primary and secondary.
u.
VOC Content: For sealants used inside of the weatherproofing system, not more
than 250 g/L when calculated according to 40 CFR 59, Subpart D.
Spacer: [Manufacturer's standard spacer material and construction] [Aluminum with mill
or clear anodic finish] [Aluminum with black, color anodic finish] [Aluminum with
bronze, color anodic finish] [Aluminum with powdered metal paint finish in color
selected by Architect] [Galvanized steel] [Stainless steel] [Polypropylene covered
stainless steel in color selected by Architect] [Thermally broken aluminum]
[Nonmetallic laminate] [Nonmetallic tube] <Insert material>.
Desiccant: Molecular sieve or silica gel, or blend of both.
088100 GLASS
Page 4 of 6
Corner Construction: [Manufacturer's standard] [Soldered, welded, or bent; keyed joints and
corners are not permitted].
SPANDREL INSULATING GLASS
F.
Double-Glazed Spandrel Insulating Glass Units:
Conformance: ASTM E 2190, Class CBA.
Outboard Lite:
a.
Clear Float Glass: [clear] [low-iron] ASTM C 1036, Type I, Class 1,
Quality q3.
b.
Tinted Float Glass: [green-tinted] [TwilightGreen®] [CrystalGray®] [gray] ASTM
C 1036, Type I, Class 2, Quality q3.
c.
Vacuum Deposition Sputtered Coating on Surface No. 2, ASTM C1376:
[SunGuard AG 43] [SunGuard AG 50] [SunGuard Silver 20] [SunGuard Neutral
40] [SunGuard Neutral 50] [SNX 51/23] [SNX 62/27] [SunGuard SN 68]
[SunGuard SN 62] [SunGuard SN 54] [SunGuard SNR 43] [SunGuard Neutral 61]
[Neutral 78/65] [none].
d.
Glass Thickness: [3 mm (1/8 inch)] [4 mm (5/32 inch)] [5 mm (3/16 inch)] [6 mm
(1/4 inch)] [8 mm (5/16 inch)].
e.
Heat Treatment: [Heat-strengthened, ASTM C 1048, Kind HS] [Tempered; ASTM
C 1048, Kind FT; CPSC 16CFR-1201].
Air Space: [6 mm (1/4 inch)] [12 mm (1/2 inch)] wide, hermetically sealed, dehydrated air
space.
Inboard Lite:
f.
Clear Float Glass: [clear] [low-iron] ASTM C 1036, Type I, Class 1,
Quality q3.
g.
SunGuard Spandrel HT on No. 4 surface: [White] [Warm Gray] [Black].
h.
Glass Thickness: [3 mm (1/8 inch)] [4 mm (5/32 inch)] [5 mm (3/16 inch)] [6 mm
(1/4 inch)] [8 mm (5/16 inch)].
i.
Heat-Treatment: [Heat-strengthened, ASTM C 1048, Kind HS] [Tempered; ASTM
C 1048, Kind FT; CPSC 16CFR-1201].
Sealing System: Dual seal, approved by glass manufacturer, with [fabricator's standard]
[polyisobutylene and polysulfide] [polyisobutylene and silicone] [polyisobutylene
and hot-melt butyl] [polyisobutylene and polyurethane] primary and secondary.
j.
VOC Content: For sealants used inside of the weatherproofing system, not more
than 250 g/L when calculated according to 40 CFR 59, Subpart D.
Spacer: [Manufacturer's standard spacer material and construction] [Aluminum with mill
or clear anodic finish] [Aluminum with black, color anodic finish] [Aluminum with
bronze, color anodic finish] [Aluminum with powdered metal paint finish in color
selected by Architect] [Galvanized steel] [Stainless steel] [Polypropylene covered
stainless steel in color selected by Architect] [Thermally broken aluminum]
[Nonmetallic laminate] [Nonmetallic tube] <Insert material>.
Desiccant: Molecular sieve or silica gel, or blend of both.
Corner Construction: [Manufacturer’s standard] [Soldered, welded, or bent; keyed joints
and corners are not permitted].
088100 GLASS
Page 5 of 6
PART 3 - EXECUTION
EXAMINATION
A.
Examine areas to receive glass. Notify Architect of conditions that would adversely affect
installation. Do not proceed with installation until unsatisfactory conditions are corrected.
PREPARATION
B.
Verify glazing openings are correct size and within tolerance.
C.
Verify glazing channels, recesses, and weeps are clean and free of obstructions.
GLAZING
D.
Install glass in accordance with manufacturer's instructions, except where local codes or GANA
Glazing Manual indicate more stringent requirements.
FIELD QUALITY CONTROL
E.
Coated glass, when viewed from minimum of 10 feet, exhibiting slightly different hue or color
not apparent in hand samples, will not be cause of rejection of glass units, as determined by
Architect.
F.
Verify glass is free of chips, cracks, and other inclusions that could inhibit structural or aesthetic
integrity.
CLEANING
G.
Clean glass promptly after installation in accordance with manufacturer's instructions.
H.
Remove labels from glass surface.
I.
Do not use harsh cleaning materials or methods that would damage glass.
PROTECTION
J.
Protect installed glass from damage during construction.
K.
Protect installed glass from contact with contaminating substances resulting from construction
operations.
L.
Remove and replace glass that is broken, chipped, cracked, abraded, or damaged in other ways
during construction period, including natural causes, accidents, and vandalism.
END OF SECTION
088100 GLASS
Page 6 of 6