Release Highlights for CAM350 Product Version 7.6
Release, December 2002
Copyright 1994-2002, DownStream Technologies, LLC
Introduction to CAM350 Version 7.6
Version 7.6 is the follow-on update to Versions 7.0 and 7.5. Version 7.6 introduces the new Fast Array
Module option allowing for both the PCB Fabricator and the PCB Designer to access standard panelization
tools. Version 7.6 also updates the PCAD 2001 and PCAD 2002 CAD interface.
Version 7.6 allows you to automate your sub-panel process with the Fast Array Module. You can create panel
templates, which can be used and stored for reuse. You can populate panels in either an automatic stepping
mode or use spreadsheet mode for total control. With the Fast Array Module in automatic mode, you pick the
assembly panel size, and we populate with best utilization based on your spacing requirements. You can also
use the spreadsheet mode, which allows placing and rotation of individual boards to meet your specific subpanel requirements.
With Version 7.5 from DownStream Technologies, the FabFactory product line and the CAM350 product line
are merged back into a single product line which will retain the CAM350 name. The focus of DownStream
Technologies remains to provide leading edge CAM tools to both the PCB Design and PCB Fabrication
markets. However, this merger of the two product lines provides all customers with access to powerful
modules previously only available in the high-end FabFactory product line. This allows both the PCB
Fabricator and the PCB Designer to access tools for DFF analysis, MRC and Quote Agents, Advanced Panel
and NC Editors, ODB++ Input and Output, and many other features. Version 7.5 also contains a number of
software corrections made since the release of Version 7.0.
Version 7.0 was the first major release of CAM350 with special focus specifically to the Printed Circuit Board
Fabricators. The ODB++ Interface and Panelization Editor are the most significant fabrication technologies to
be applied within 7.x. However, Version 7.0 was focused on more than just the PCB Fabricators. The Latium
architecture, representing a significant technological breakthrough in EDA system architecture, was integrated
into this release. Through Latium all users benefit from 10 times, to as much as 100 times, performance
improvement in critical design and manufacturing analysis areas. Acid trap detection processes that use to
take minutes now take seconds. Sliver detections that took hours now run in seconds as well. Latium was also
applied to some of the key data optimization functions, like Netlist Extraction, in order to help increase
throughput and reduce overall processing times. A secondary benefit to migrating to the Latium architecture is
accuracy. Prior to using Latium the DFF Audits where processed using a “Raster” technique, which meant that
the user had to define a resolution. Ultimately the accuracy of the test that was being performed was then
bound by the resolution the user picked – if they didn’t choose a tight enough resolution the check would fail to
find all the problems that might exist on the PCB. Since Latium is a “Contour” based environment it has
eliminated the need for any raster processing and has improved the accuracy by as much as 50 times, since
we now have an exact edge representation of all the objects within a PCB.
Listed below you will find the Version 7.6 CAM350 Configuration Matrix, and the Transition Map for mapping
customers from CAM350/FabFactory Version 7.0 configurations to CAM350 Version 7.6 configurations. This
updated transition map from DownStream Technologies is for a product line with a long and bright future
ahead of it.
DownStream Technologies
CAM350 Version 7.6 Design Family Configurations
CAM350 Fabrication
Modules
C350-750 C350-500 C350-450 C350-255 C350-100 C350-050
Imp ort
Information
Exp ort
M odification
Op timization
M RC/DRC
DirectCAD Interface In
Basic NC Editor
Quote Agent
Fast Array M odule
DXF Interface
DFF Audit
M RC Agent
M acro Debugger
Panel Editor
Advanced NC Editor
ODB++ Imp ort
ODB++ Exp ort
DirectCAD Interface Out
Reverse Engineering
Fly ing Probe Editor
Bed of Nails Editor
Camtek AOI
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Opt.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Opt.
Opt.
Opt.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
X
X
X
X
X
X
X
X
X
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
X
X
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Mapping for CAM350 Customers
CAM350 V7.5
Maps to
CAM350 V7.6
Configuration
Configuration

CAM350-250

CAM350-255 plus:
Fast Array Module
Mapping for CAM350 Customers
CAM350 V7.0
Maps to
CAM350 V7.6
Configuration
Configuration

CAM350-050

CAM350-100

CAM350-250

CAM350-500

DownStream Technologies
CAM350-050
CAM350-100 plus:
Quote Agent
CAM350-255 plus:
Quote Agent
Fast Array Module
Macro Debugger
CAM350-500 plus:
Panel Editor
Advanced NC-Editor
Page 2
Mapping for FabFactory Customers
FabFactory V7.0
Maps to
CAM350 V7.6
Configuration
Configuration

FF-050

FF-100

FF-125

CAM350-050
CAM350-100 plus:
Export
Direct CAD Interface (Import)
Basic NC Editor
CAM350-255 plus:
Quote Agent
DFF Audit
DXF Interface
Direct CAD Interface (Import)
Fast Array Module
FF-250

FF-500

DownStream Technologies
CAM350-450 plus:
Quote Agent
MRC Agent
Direct CAD Interface (Import)
CAM350-750 plus:
Reverse Engineering
Direct CAD Interface (Import)
Page 3
Customer Reported Software Corrections
Some of the customer reported issues were addressed in CAM350 7.6 include:
IMPORT
----9971,10286,10905,11035 – AccelEDA (PCAD) files for PCAD 2001 version files are now
supported.
10792,10929 – The ODB++ Import command no longer drops drills for certain designs.
10818 – The Gerber Import command no longer drops voids for certain cutline polygons.
10836 – The Gerber Import command no longer fails for designs with certain polygon definitions
with arcs.
10921 – The Gerber Import command performance is improved for cutline polygon import.
10975 – The PADS Import command now correctly handles certain designs with certain padstack
definitions.
ANALYSIS
----10762 – Pad to Solder Mask DRC check displays a negative clearance to report the annular ring
size for solder mask that overlaps a pad.
UTILITIES
----10906 – The Composite To Layer command no longer fails for designs with certain polygon
definitions.
10909 – Remove Redundant Data command no longer removes certain thermals for certain
positive plane designs.
10950 – The Camtek AOI interface properly translates certain polygon outlines for certain designs
with positive planes.
10961 - Netlist extract for MCM designs no longer drops insulator layer pads (10443,10751,11032)
10976 – The Camtek properly works for certain Camtek.INI files.
11022 - Netlist extract now properly merges nets for MCM designs
PRINTING
----10708 – Printing to a file can now be reset to another printer properly.
INFORMATION
----11026 – Measuring distance between objects and an asymmetric custom aperture is correct.
PANEL EDITOR
----10864 – Deleting Pinholes now works properly for the Setup dialog in the Panel Editor.
FLYING PROBE EDITOR
----10874 – SMT pads are now properly totaled for Info->Report->Test Points output.
NC EDITOR
----10962 - Gerber to Mill now longer fails for certain designs.
EXPORT
----10948 - IPCD356A output is correct for drills with size greater than 4.2 mm.
10969 – The Mill Path is no longer incorrect after exporting Mill Data.
P-CAD 2001 and P-CAD 2002 are registered trademarks of Accel Technologies, Inc.
DownStream Technologies
Page 4