Jerry & Penny Koerner
6300 Reed Rd
Ridgeway, WI 53582
608-924-3091
dogbite@mhtc.net
Sun Harvest Farm
Renewable Energy Projects
September 2009 Update
General:
In 2005 we embarked on major renovations and additions to our old farmhouse. This included
working with Focus on Energy to have site assessments performed for Solar Photovoltaic, Solar
Thermal and Wind Turbine Systems. We also investigated wood burning systems because we have
substantial quantities of firewood on our property. Our decisions included the following:
1. Add additional insulation, all new windows and new doors.
2. Replace our old oil burning furnace with a high efficiency propane boiler (our little Munchkin).
3. Install a Solar Photovoltaic grid-connected system to produce electricity.
4. Install a Solar Thermal (hot water) system to preheat domestic hot water and provide some
house heat.
5. Install a counter-flow masonry heater fireplace using our own limestone for the masonry
cladding.
6. In 2008 we built and installed a hot air collector to provide some heat in our barn workshop.
7. In 2009 we installed our 2nd Photovoltaic grid-connected system.
8. In 2009 we also upgraded our solar hot water storage tank
Improving Efficiency
Our first goal was to improve the efficiency of the areas in the old part of the farmhouse, and to
include very high efficiency within the new addition. We installed new Pella windows and doors
throughout. Additional insulation was added where possible and a moisture/air barrier under new fiber
cement siding, which was installed on the entire house. The new construction included R-21 insulation
in the walls and blown-in R-50 in the ceiling. We removed the old oil-fired hot water heater and the
oil burner from the warm air furnace. A high efficiency propane gas boiler (Munchkin T-50) was
installed to be our back up for heating and the new domestic hot water tank. We also installed radiant
under floor heating in the new great room area and plan to install additional radiant heating in certain
of the old house areas. The existing warm air furnace was retained, with the addition of a water-to-air
heat exchanger, which allowed us keep the central AC unit and also to provide warm air heating to the
upstairs area. We have also installed compact fluorescent light bulbs throughout the entire house and
in the barn workshop area.
Solar Thermal Hot Water System
Our system as designed to provide domestic hot water and a portion of the house heating and was put
into operation in March 2006. It includes:
 Eight 4 ft x 10 ft Heliodyne Gobi 410 collectors, ground-mounted at a 60 degree tilt angle
 1000 gallon concrete hot water storage tank, with EPDM rubber liner
 Approximately 600 ft of 1 inch copper tubing made into coils for heat exchangers
 Pump, valves, expansion tanks, controller, copper piping, propylene glycol, insulation, etc.
We performed a considerable amount of the work to install the system including:





Installing the concrete tank and liner
Bending the tubing into coils and installing them in the tank
Installing 14 concrete pillars
Digging trenches and installing piping from collectors into basement
Erecting the framework and the collectors
We worked with Light Energy Systems of Madison (now Full Spectrum Solar) to design the system
and to provide the parts and some of the labor. The total system cost was approximately $20,000, but
we received a Focus on Energy grant of $3,000 and a Federal Tax Credit of $2,000 so our out-ofpocket costs were about $15,000.
During 2009 we decided to replace the concrete tank due to excessive moisture problems in the
basement area. We demolished the tank piece by piece and carried it out of the basement. We
replaced it with a tank made by STSS Co. Inc from Mechanicsburg PA. The new tank is collapsible so
2/13/2016
Page 1 of 3
it can be moved through regular sized doorways. When in place it will be 80” round and 4’ high with
all penetrations installed at the factory according to our heat exchanger specifications. It is sealed,
insulated and with hold up to 822 gallons of water. We reused the copper heat exchangers that we had
made for the old tank. We also installed a “heat dump” under the solar collectors, which was made of
24 ft of Slant Fin baseboard hydronic registers. The purpose of the heat dump is to dissipate excess
heat produced during the summer when we only use the hot water for pre-heating the domestic hot
water. The total costs for the new tank, including demolishing the old tank, were about $3,500.
Masonry Heater Fireplace
We investigated wood-burning systems and decided to build a masonry heater fireplace in order to take
advantage of renewable resources on our property. We have an ample supply of trees on our property
that we harvest by cutting dead trees. We constructed a woodshed that dries and stores about 10 cords
of split firewood.
The fireplace is specially designed to be efficient and environmentally friendly because the combustion
chamber burns at between 1500-2000 degrees F. The fire burns for 2-3 hours but the large amount of
masonry mass stores and radiates the heat for 12-24 hours. Our fireplace is centrally located so it
radiates heat over a large area of our kitchen and great room. Two stainless steel U-Tube heat
exchangers are also built into the core to capture some heat, which is circulated to the solar storage
tank in the basement.
The core of our heater was designed by Heat-Kit of Canada, but originated centuries ago from designs
in Europe and Russia. Gimme Shelter Construction of Amherst, WI constructed the core.
We decided to use natural limestone and sandstone from our property for the masonry cladding. Some
of the stones were recovered from the foundation of our old summer kitchen. We performed the
masonry work ourselves, which saved us $20,000+ in labor costs. Our cost for the core, chimney
materials and mortar for the limestone was approximately $12,000.
Solar Photovoltaic Electric System # 1
This system was designed to produce about half of our annual electricity needs and was put into
operation in April 2006. We chose a grid-tied system that sends excess electricity to the Alliant
Energy power grid. We have a net-metering agreement where we are compensated for the power we
produce at the same rate as we pay for electricity. During the first full year of operation our PV system
produced 4,700 kilowatt-hours, which was 43% of our total usage of 11,100 kWh.
The PV system includes the following components:
 16 Kyocera 170 watt modules for a total output of 2.7 kW
 Wattsun dual axis tracker system (the system follows the sun morning until night)
 SMA Sunny Boy 2500 inverter/controller (converts DC voltage to AC for the grid)
 Concrete foundation (5 yds with rebar), steel post & framework
 Disconnect switches, wires, conduit, and other miscellaneous electrical items
Our system produces between 200-600 volts (DC current) when the sun shines. It is facing east when
the sun rises and follows the sun all day so it is facing west when the sun goes down. The DC current
comes into the basement, goes through a disconnect switch and into the Sunny Boy inverter/controller.
This device changes the DC current into AC current and controls how the power goes out into the grid.
The current goes outside through a disconnect switch, back through our main breaker panel, and then
out through the meter to the grid. The best days are when we are not using much power and the meter
is actually going backward!
We worked with Light Energy Systems of Madison (now Full Spectrum Solar) to design the system
and to provide the parts and some of the labor.
The total cost of the system was about $25,000, but we received a Focus on Energy grant of $8,700
and a Federal Tax Credit of $2,000, so out out-of-pocket costs were about $14,000.
Solar Photovoltaic Electric System # 2
In 2009 we installed our second PV system. We took advantage of a special program from Alliant
Energy where we have contracted for 10 years to sell all of the power produced by the system for 25
2/13/2016
Page 2 of 3
cents per kWh. It did require us to install a new meter pedestal, at a cost of $1,100 so that the
electricity from the new system could be metered separately. We also have to pay about 41 cents/day
for the new meter charge, as well as sign up for the Alliant Second Nature program (where we pay a
small premium for our energy purchased, which will be from renewable sources). Our total cost for
the system was $31,168, and we did some of the work ourselves (digging, concrete, trenching, wire,
etc). We will get a 25% Focus on Energy grant of about $7,800 and a 30% Federal tax credit in 2010
of about $9,300. Therefore, our out of pocket costs will be about $14,000. This system has the
potential to produce about an 11% annual rate of return.
We purchased the main part of the system from DH Solar. Their system uses a tracking system that
they adapted from their experience with commercial satellite tracking systems. The system has 16
Suncast PV panels, each of which is rated at 210 watts, or a total of 3.36 kW. The inverter is a SMA
Sunny Boy 3000US.
Barn Workshop Hot Air Collector System
In 2008 we designed, built and installed a hot air collector system on the south side of the old
milkhouse. The collector was made from tempered glass, aluminum expandable tubes, painted black,
and solid foil-faced insulation. The 6” outlet and inlet piping contains a bi-metallic sensor/control
relay and a small in-duct fan to pipe the heat into the barn workshop. The total cost of this system was
about $600. A woodstove in the milk house provides backup heat on cloudy days, which is piped with
the same piping system into the barn. This is a trial and error system. It looks like we might have to
reposition the system to more directly face south to maximize the heat output.
2/13/2016
Page 3 of 3