MeiJet Coating and Inks, Inc. 1309 Jianchuan Road, Building #1 and #2 Shanghai, Zip Code 200240 P. R. of China Phone: 86-21-54756338 Fax: 86-21-64632963 Web Site: www.meijet.com E-mail:meijet@126.com Material Safety Data Sheet Solvent Inks PRODUCT & COMPANY IDENTIFICA 1.Products and Company Identification Supplier Meijet Coating and Inks, Inc., 1309 Jianchuan Road, Building #1, Shanghai, P. R. of China. Zip Code: 200240, Phone 86-21-54756338 Solvent inks black, cyan, magenta, yellow colors Product Name 2.Compostion/information on ingredients Chemical Name Formula CAS No. Proportion Pigment NE Proprietary 5-10 Ethylene glycol monobutyl ether acetate C8H16O3 112-07-2 75-85 Other NE Proprietary 10-15 NE=Not Established 3.Physical and chemical properties Appearance and Odor This product has a distinct odor and comes in a variety colors (black, magenta, cyan, yellow) Boiling Point 186 - 194 º C Vapor Pressure <1.00 mm Hg @ 20 º C Vapor Density 5.6 (air = 1) Specific Gravity 0.960 - 0.970 Evaporation Rate 0.03 (butyl acetate = 1) % VOC’s (by Wt.) 100% 4.Fire fighting measures 1 MeiJet Coating and Inks, Inc. 1309 Jianchuan Road, Building #1 and #2 Shanghai, Zip Code 200240 P. R. of China Phone: 86-21-54756338 Fax: 86-21-64632963 Web Site: www.meijet.com E-mail:meijet@126.com I Flash Point Lower Flammable Level Upper Flammable Level Extinguishing Media Special Fire Fighting procedures Unusual Fire Fighting Hazards 55º C , COC 0.9% 8.5% Water fog, foam, CO2, dry chemical Product is combustible. Use self-contained breathing apparatus and full bunker gear in fire areas. Keep containers cool with water fog to minimize swelling taking care not to spread flames with water used for cooling. Vapors are heavier that air and may travel along the ground or be moved by ventilation and ignited by heater, pilot lights, or other ignition sources at locations distant from material handling point. Never use welding or cutting torch on or near drum (even empty) because product (even residue) can ignite explosively. All five-gallon pails and larger metal containers including tank cars and tank trucks should be grounded and/or bonded when material is transferred. 5. Stability and reactivity Conditions To Avoid Extreme heat and ignition sources Incompatibilities (Materials To Avoid) Strong alkalies and oxidizers Hazardous Decomposition Or Byproducts CO and CO2 under fire conditions Hazardous Polymerization Will not occur HEALTH HAZARD DATA 7.Health hazard data Route(S) Of Entry: contact may and inhalation primary; ingestion possible. Not listed as carcinogenic. Acute and Chronic: Eyes Skin Contact may cause mild eye irritation including stinging, watering and redness. Contact may cause mild skin irritation including redness, burning and drying and cracking of the skin. No harmful effects from skin absorption are expected 2 MeiJet Coating and Inks, Inc. 1309 Jianchuan Road, Building #1 and #2 Shanghai, Zip Code 200240 P. R. of China Phone: 86-21-54756338 Fax: 86-21-64632963 Web Site: www.meijet.com E-mail:meijet@126.com . Inhalation Low to moderate degree of toxicity by inhalation. may cause irritation to upper respiratory tract and CNS depression Ingestion Low degree of toxicity by ingestion. Aspiration hazard. Can enter lungs during swallowing or vomiting and cause chemical pneumonia and edema. SIGNS AND SYMPTOMS OF OVEREXPOSURE 8.First-aid measures Reddening and irritation of contact areas; coughing and dizziness with prolonged inhalation of mist/ vapors; nausea if ingested. EMERGENCY FIRST AID PROCEDURES Eyes Flush with water for 15 minutes. Seek immediate medical attention. Skin Wash exposed areas with water and mild soap. Remove contaminated clothing immediately and launder before reuse. If an irritation persists, seek medical attention. Inhalation Remove victim to fresh air. Administer oxygen or artificial respiration if breathing is affected or stopped. Seek immediate medical attention. Ingestion Do not induce vomiting. Seek immediate medical attention. STEPS TO BE TAKEN IF MATERIALS ARE RELEASED Accidental release measures If material is released or spilled, keep all sources of ignition and hot metal surfaces away from spill/release. Evacuate all unprotected personnel from area. Contain spill. Use foam on spills to minimize vapors. Contain spill if it can be done with minimal risk. Collect spill on absorbent material and put into approved container. Do not flush to drains or sewers. Notify proper authorities. WASTE DISPOSAL METHOD Follow federal, state, and local regulation. Not a RCRA hazardous waste if uncontaminated. STORING AND HANDLING PRECAUTIONS Handling and storage NFPA class III B storage. Avoid prolonged breathing of mist or vapor. Wash thoroughly after handling. “Empty” containers retain residue and/or vapor and may be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grinding, or expose such containers to heat, flames, sparks, or other sources of ignition. Keep containers tightly closed when not in use. PERSONAL PROTECTION Exposure controls/personal protection Respiratory Protection NIOSH approved respirators for high mist/vapor areas or confined space. Ventilation Adequate local or mechanical to reduce mist/vapor. Protective Gloves Solvent impervious Eye Protection Goggles or approved OSHA device Clothing Apron Work/Hygienic Practices Follow accepted work hygiene practices. OTHER Other information The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. We make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and we assume no liability resulting from its use. Users should make their own investigations to determine the suitability of the information for their particular 3 MeiJet Coating and Inks, Inc. Phone: 86-21-54756338 1309 Jianchuan Road, Building #1 and #2 Fax: 86-21-64632963 Shanghai, Zip Code 200240 Web Site: www.meijet.com P. R. of China E-mail:meijet@126.com purposes. In no way shall we be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising from using the above information. 4