SECTION 08556
COMPOSITE-CLAD WOOD WINDOWS AND DOORS
(Andersen Windows Inc A-Series)
Copyright 2013 - 2013 ARCAT, Inc. - All rights reserved
** NOTE TO SPECIFIER ** Andersen Windows, Inc.; windows and doors.
.
This section is based on the products of Andersen Windows, Inc., which is located at:
100 Fourth Ave. N. P. O. Box 12
Bayport, MN 55003-1096
Toll Free Tel: 800-299-9029
Tel: 651-264-5150
Fax: 752-752-9230
Email:request info (apanning@andersencorp.com)
Web:www.andersenwindows.com
[ Click Here ] for additional information.
For over 100 years, Andersen has been making windows and doors that are different and better
than any others. Today, we offer five distinct product lines to provide the exact combination of
economy, performance, aesthetics and architectural authenticity for any type of home and every
homeowner's taste. Find the one that's right for you.
PART 1 GENERAL
1.1
SECTION INCLUDES
** NOTE TO SPECIFIER ** Delete items below not required for project.
A.
Composite-clad wood windows of the following types: (Andersen Windows Inc A-Series)
1.
Double-hung windows.
2.
Casement windows.
3.
Awning windows.
4.
Picture windows.
5.
Transom fixed windows.
6.
Transom venting windows.
B.
Composite-clad wood gliding patio doors of the following types: (Andersen Windows Inc ASeries)
1.
Gliding patio doors.
C.
Composite-clad wood hinged patio doors of the following types: (Andersen Windows Inc ASeries)
1.
Hinged patio doors.
2.
Outswing patio doors.
3.
Patio door sidelights.
4.
Patio door transoms.
1.2
RELATED SECTIONS
** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as
required.
A.
Section 04810 - Unit Masonry Assemblies: Openings in masonry.
08556-1
B.
Section 05400 - Cold Formed Metal Framing: Framed Openings.
C.
Section 06100 - Rough Carpentry: Framed openings.
D.
Section 06200 - Finish Carpentry: Interior wood casing.
E.
Section 07210 - Building Insulation: Batt insulation at window perimeter.
F.
Section 07460 - Siding and trim: Exterior siding and trim.
G.
Section 07620 - Flashing and Sheet Metal: Flashing associated with windows and doors.
H.
Section 07900 - Joint Sealers: Perimeter joint sealant and backer rod.
1.3
REFERENCES
** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by
the text of the edited section.
A.
AAMA 511 - Voluntary Guideline for Forensic Water Penetration Testing of Fenestration
Products.
B.
AAMA 502 - Voluntary Specification for Field Testing of Windows and Sliding Glass Doors.
C.
AAMA/WDMA/CSA 101/I.S.2/A440 NAFS - North American Fenestration
Standard/Specification for windows, doors, and skylights.
D.
ASTM International (ASTM):
1.
ASTM C 1036 - Standard Specification for Flat Glass.
2.
ASTM C 1048 - Standard Specification for Heat-Treated Flat Glass--Kind HS, Kind FT
Coated and Uncoated Glass.
3.
ASTM E 90 - Standard Test Method for Laboratory Measurement of Airborne Sound
Transmission Loss of Building Partitions and Elements.
4.
ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows,
Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.
5.
ASTM E 2190 - Standard Specification for Insulating Glass Unit Performance and
Evaluation
E.
American Society of Civil Engineers (ASCE) 7 - Minimum Design Loads for Buildings and
Other Structures.
F.
International Standards Organization (ISO) 14021 - Environmental Labels and Declarations - Self-Declared Environmental Claims (Type II environmental labeling).
G.
National Fenestration Rating Council (NFRC) 100 - Procedure for Determining Fenestration
Product U-factors.
H.
National Fenestration Rating Council (NFRC) 200 - Procedure for Determining Fenestration
Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence.
I.
WDMA I.S.4 - Water-Repellent Preservative Treatment for Millwork.
1.4
SYSTEM DESCRIPTION
** NOTE TO SPECIFIER ** Refer to website for most current product performance data. Retain,
edit, or delete language below to suit project requirements. Refer
towww.andersenwindows.comfor performance information.
A.
Performance Requirements: Provide products/systems that have been manufactured,
fabricated, and installed to the following performance criteria:
08556-2
1.
Comply with AAMA/WDMA/CSA 101/I.S.2/A440.
** NOTE TO SPECIFIER ** Specify performance grade.
2.
Performance Grade:
** NOTE TO SPECIFIER ** Specify U-Factor.
3.
U-Factor (NFRC 100):
** NOTE TO SPECIFIER ** Specify SHGC.
4.
Solar Heat Gain Coefficient (SHGC) (NFRC 200):
** NOTE TO SPECIFIER ** Specify OITC.
5.
Outdoor-Indoor Transmission Class (OITC) (ASTM E90):
** NOTE TO SPECIFIER ** Specify STC.
6.
Sound Transmission Class (STC) (ASTM E90):
** NOTE TO SPECIFIER ** Manufacturer recommends referring to website design pressure
estimator for additional wind load information. Retain, edit, or delete language below to suit
project requirements.
B.
Structural Requirements: Provide products/systems capable of withstanding wind loads
based on testing units representative of those indicated for Project that pass
AAMA/WDMA/CSA 101/I.S.2/A440, Uniform Structural Load Test:
1.
Design Wind Loads: Determine design wind loads applicable to Product from basic
wind speed indicted in miles per hour (meters per second) at 33 feet (10 meters)
above grade, according to ASCE-7, Section 6, based upon mean roof heights indicted
on Drawings.
** NOTE TO SPECIFIER ** Specify wind speed.
a.
Basic Wind Speed:
** NOTE TO SPECIFIER ** Specify importance factor.
b.
Importance Factor:
** NOTE TO SPECIFIER ** Specify exposure category.
c.
Exposure Category:
** NOTE TO SPECIFIER ** Specify design pressure requirement.
d.
Wind Load Requirement:
1.5
SUBMITTALS
A.
Submit under provisions of Section 01300.
B.
Product Data: Manufacturer's data sheets on each product to be used, including:
1.
Preparation instructions and recommendations.
2.
Storage and handling requirements and recommendations.
3.
Installation methods.
C.
Shop Drawings: Provide drawings indicating direction of operable parts, typical jamb, head
and sill conditions, and special mullion reinforcement details.
D.
Quality Assurance/Control Submittals:
1.
Performance Data: Manufacturer's published performance data for specified products.
** NOTE TO SPECIFIER ** Delete if not required.
E.
Sustainable Building Submittals:
** NOTE TO SPECIFIER ** Retain subparagraph below and energy performance certification
paragraph in quality assurance article if wood windows are required to be certified. Delete if not
required.
1.
Energy Performance:
a.
Provide NFRC 100 and NFRC 200 Certified performance values meeting or
exceeding values specified in Performance Criteria Article.
08556-3
** NOTE TO SPECIFIER ** Retain subparagraph below and recycled content certification in quality
assurance article. Delete if not required.
2.
Recycled Content.
a.
Provide values in percent by weight of recycled content per ISO 14021
Standard for each product specified.
b.
Provide statement indicating total content value for each product containing
recycled content and fraction by weight that is considered recycled content.
** NOTE TO SPECIFIER ** Retain subparagraph below if wood windows are required to be
qualified for regional materials. Delete if not required.
3.
Regional Materials.
a.
Provide window manufacturer's Product Data for regional materials within 500
miles of project location, indicating location and distance from Project of
material manufacturer and point of extraction, harvest, or recovery and
manufacture for each qualifying window component.
b.
Provide statement indicating content value for each product containing regional
material and the fraction by weight that is considered regional material.
4.
FSC Wood-based Materials.
a.
Provide third party certification that wood-based window materials retain FSC
Chain-of-Custody certification.
b.
Provide statement indicating total content value for each product containing
FSC wood-based content and fraction by weight that is considered FSC woodbased content.
** NOTE TO SPECIFIER ** Retain paragraph below if windows are required to be certified for
indoor air quality Delete if not required.
5.
Indoor Environmental Quality.
a.
Provide third party certification that window materials, including factory applied
finishes, meet indoor air quality standards for low emitting materials under
California CA Section 01350 Specifications.
** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
1.6
F.
Selection Samples: For each finish product specified, two complete sets of color chips
representing manufacturer's full range of available colors and patterns.
1.
Hardware: Submit samples indicating typical finish on window hardware.
2.
Cladding: Submit color samples of vinyl cladding.
3.
Interior Finishes: Submit color samples of interior finishes.
G.
Verification Samples: For each finish product specified, two samples, minimum size 6 inches
(150 mm) square, representing actual product, color, and patterns.
1.
Hardware: Submit samples indicating typical finish on window hardware.
2.
Cladding: Submit color samples of vinyl cladding.
3.
Interior Finishes: Submit color samples of interior finishes.
H.
Manufacturer's Warranty: Submit, for Owner's acceptance, manufacturer's standard limited
warranty document.
I.
Owner's Manual: Bound manual clearly identified with project name, location, and
completion date. Identify type and size of units installed. Provide recommendations for
periodic inspections, care, and maintenance. Identify common causes of damage with
instructions for temporary repair.
QUALITY ASSURANCE
A.
Manufacturer Qualifications: A manufacturer capable of fabricating wood windows that meet
or exceed Performance Criteria indicated and of documenting this performance by inclusion
in lists and by labels, test reports, and calculations.
08556-4
** NOTE TO SPECIFIER ** Delete FSC certification for manufacturer and vendor if not required..
1.
A manufacturer who is certified for chain-of-custody by an FSC accredited certification
body.
2.
Vendor Qualifications: A vendor that is certified for chain of custody by an FSC
accredited certification body.
B.
Installer Qualifications: Utilize an installer having demonstrated experience on projects of
similar size and complexity.
** NOTE TO SPECIFIER ** Specify applicable requirements of regulatory agencies.
C.
Regulatory Requirements and Approvals:
D.
Certifications:
1.
National Fenestration Rating Council (NFRC). Products shall be certified and labeled
for U-Factor, Solar Heat Gain Coefficient (SHGC), and Visible Transmittance per
NFRC 100 and 200 Procedures. Unique glass types that are special ordered may not
apply, check with Manufacturer.
2.
Window and Door Manufacturers Association (WDMA). Products shall be certified and
labeled per WDMA Hallmark Certification Program to the AAMA/WDMA/CSA
101/I.S.2/A440 industry standard.
** NOTE TO SPECIFIER ** Delete certification label not required.
3.
Insulating Glass Units: Provide insulating glass units permanently marked with
certification label of Insulating Glass Certification Council (IGCC) indicating
compliance with ASTM E2190.
4.
Insulating Glass Units: Provide insulating glass units permanently marked with
certification label of Insulating Glass Manufacturers Association of Canada (IGMAC)
indicating compliance with CAN/CGSB or ASTM E2190.
** NOTE TO SPECIFIER ** Retain paragraph below if pre-installation meeting is required. Specify
requirements for pre-installation meeting.
E.
Pre-Installation Meetings: Conduct meeting at Project site to comply with requirements in
Division 01 Section - Project Management and Coordination.
** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such
a precaution. The following is one example of how a mock-up on a large project might be
specified. When deciding on the extent of the mock-up, consider all the major different types of
work on the project.
F.
1.7
Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and
application workmanship.
1.
Finish areas designated by Architect.
2.
Do not proceed with remaining work until workmanship, color, and sheen are
approved by Architect.
3.
Refinish mock-up area as required to produce acceptable work.
DELIVERY, STORAGE, AND HANDLING
A.
Comply with manufacturer's ordering instructions and lead time requirements to avoid
construction delays.
B.
Delivery: Deliver materials in manufacturer's original unopened, undamaged containers with
identification labels intact.
C.
Storage and Protection: Store materials protected from exposure to harmful environmental
conditions and at temperature and humidity conditions recommended by the manufacturer.
D.
Store materials and accessories off ground, under cover, and protected from weather and
08556-5
construction activities.
E.
1.8
Store and dispose of solvent-based materials, and materials used with solvent-based
materials, in accordance with requirements of local authorities having jurisdiction.
PROJECT CONDITIONS
A.
Field Measurements: Verify actual dimensions of openings by field measurements before
fabrication. Record measurements on shop drawings. Coordinate field measurements and
fabrication schedule with construction progress to avoid construction delays.
B.
Install units in accordance with manufacturer's safety and weather requirements.
1.
Maintain environmental conditions (temperature, humidity, and ventilation) within limits
recommended by manufacturer for optimum results. Do not install products under
environmental conditions outside manufacturer's absolute limits.
1.9
WARRANTY
** NOTE TO SPECIFIER ** Andersen window & doors are covered by our exclusive Owner-toOwner limited warranty. Most other window warranties end when a home is sold, but our coverage
is completely transferable from each owner to the next. And, because it is not prorated, the
coverage offers full benefits, year after year, owner after owner, so it can add real value when you
decide to sell your home. Plus, we have one of the largest service networks in the industry, so
help is always there if you need it.
A.
Project Warranty: Refer to Conditions of the Contract for project Warranty provisions.
** NOTE TO SPECIFIER ** Coordinate article below with manufacturer's warranty requirements.
Visit the Andersen website for a complete description of the standard limited warranty including
exclusions and limitations.
B.
Manufacturer's Warranty: Manufacturer's standard limited warranty.
1.
Non-prorated. Transferable from owner to the next.
2.
Term: 20 years on glass.
3.
Term: 10 years on non-glass parts.
C.
Andersen A Series window units are warranted to be free from defects in manufacturing,
materials and workmanship for ten years from the date of purchase.
D.
The glass is warranted not to develop, under normal conditions, any material obstruction of
vision resulting from manufacturing defects or as a result of premature failure of the glass or
organic seal for ten years from the date of purchase.
PART 2 PRODUCTS
2.1
MANUFACTURERS
A.
Acceptable Manufacturer: Andersen Windows, Inc., which is located at: 100 Fourth Ave. N.
P. O. Box 12 ; Bayport, MN 55003-1096; Toll Free Tel: 800-299-9029; Tel: 651-264-5150;
Fax: 752-752-9230; Email:request info (apanning@andersencorp.com);
Web:www.andersenwindows.com
** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with
requirements of Division 1 section on product options and substitutions.
B.
Substitutions: Not permitted.
C.
Requests for substitutions will be considered in accordance with provisions of Section
01600.
** NOTE TO SPECIFIER ** When designing window sizes, consult with Andersen window's A-
08556-6
series window product guide document available at www.andersenwindows.com for full
description of clear opening dimensions and positions. Delete if not required.
2.2
WINDOWS
** NOTE TO SPECIFIER ** Delete window products not required for project. Delete if not required.
A.
Double-Hung Windows:
1.
Product: Andersen A-Series Full Frame Double-Hung Windows.
** NOTE TO SPECIFIER ** Andersen casement windows have a hinge at the side and crank open
outward. Delete if not required.
B.
Casement Windows:
1.
Product: Andersen A-Series Casement Windows.
** NOTE TO SPECIFIER ** Andersen awning windows have a hinge at the top and open outward.
Delete if not required.
C.
Awning Windows:
1.
Product: Andersen A-Series Awning Windows.
** NOTE TO SPECIFIER ** Andersen picture windows are stationary windows designed to match
double-hung, gliding or casement windows. Picture windows have no moving hardware and offer
a wider, brighter view of the outdoors. Delete if not required.
D.
Picture Windows:
1.
Product: Andersen A-Series Picture Windows.
** NOTE TO SPECIFIER ** Andersen transom windows are stationary windows designed to match
double-hung, gliding or casement windows. Transom windows are often found over entry doors
or other windows. Delete if not required.
E.
Transom Fixed Windows:
1.
Product: Andersen A-Series Transom Fixed Windows.
** NOTE TO SPECIFIER ** Andersen transom windows are windows designed to match doublehung, gliding or casement windows. Transom windows are often found over entry doors or other
windows. Venting transoms are an option. Delete if not required.
F.
Transom Venting Windows
1.
Product: Andersen A-Series Transom Venting Windows.
G.
Materials:
** NOTE TO SPECIFIER ** Required to be certified for LEED or project is being designed with
sustainable practices. Delete if not required.
1.
Certified Wood: Windows shall be certified as "FSC Mixed Credit" per FSC STD-01001, "FSC Principles and Criteria for Forest Stewardship," and FSC STD-40-004,
"FSC Standard for Chain of Custody Certification."
2.
Frame: Fabricated from a wood species approved in WDMA I.S.4.
3.
Exterior Frame Members:
a.
Material: Fibrex material outer frame with wood core. Provide units in the
following color:
** NOTE TO SPECIFIER ** Delete color not required.
1)
Color: White.
2)
Color: Sandtone.
3)
Color: Terratone.
4)
Color: Forest Green.
5)
Color: Canvas.
6)
Color: Dove Gray.
7)
Color: Prairie Grass.
08556-7
8)
Color: Red Rock.
9)
Color: Cocoa Bean.
10) Color: Dark Bronze.
11) Color: Black.
** NOTE TO SPECIFIER ** Windows can be ordered with a sash color different from the frame
color.
4.
Operable Sash Members:
a.
Exterior Sash: Pultruded fiberglass material with adhesively bonded PVC
corner keys.
b.
Interior Sash: Clear or veneer wood adhesively applied to exterior sash
components.
c.
Material with the following painted color:
** NOTE TO SPECIFIER ** Delete color not required.
1)
Color: White.
2)
Color: Sandtone.
3)
Color: Terratone.
4)
Color: Forest Green.
5)
Color: Canvas.
6)
Color: Dove Gray.
7)
Color: Prairie Grass.
8)
Color: Red Rock.
9)
Color: Cocoa Bean.
10) Color: Dark Bronze.
11) Color: Black.
d.
Interior Components: Water repellant wood preservative treated interior framing
per WDMA I.S.4 in the following species and finish. Adhesively bond exterior
and interior sash components.
** NOTE TO SPECIFIER ** Delete wood species not required.
1)
Species: Pine.
2)
Species: Oak.
3)
Species: Maple.
** NOTE TO SPECIFIER ** Delete wood finish not required.
4)
Finish: Unfinished.
5)
Finish: Clear coat finish.
6)
Finish: Stain Color - Cinnamon.
7)
Finish: Stain Color - Espresso.
8)
Finish: Stain Color - Honey.
9)
Finish: Stain Color - Mocha.
10) Finish: Stain Color - Russet.
11) Finish: Painted Color (Pine) - White.
12) Finish: Painted Color (Pine) - Birch Bark.
13) Finish: Painted Color (Pine) - Prime.
** NOTE TO SPECIFIER ** Delete if not required.
5.
Picture and Transom Sash Members:
a.
Exterior Components: Pultruded fiberglass material with adhesively bonded
PVC corner keys. in the following color:
** NOTE TO SPECIFIER ** Delete color not required.
1)
Color: White.
2)
Color: Sandtone.
3)
Color: Terratone.
4)
Color: Forest Green.
5)
Color: Canvas.
6)
Color: Dove Gray.
7)
Color: Prairie Grass.
08556-8
8)
Color: Red Rock.
9)
Color: Cocoa Bean.
10) Color: Dark Bronze.
11) Color: Black.
b.
Interior Components: Water repellant wood preservative treated interior framing
per WDMA I.S.4 in the following species and finish. Clip-fasten interior
components to exterior components.
** NOTE TO SPECIFIER ** Delete wood species not required.
1)
Species: Pine.
2)
Species: Oak.
3)
Species: Maple.
** NOTE TO SPECIFIER ** Delete wood finish not required.
4)
Finish: Unfinished.
5)
Finish: Clear coat finish.
6)
Finish: Stain Color - Cinnamon.
7)
Finish: Stain Color - Espresso.
8)
Finish: Stain Color - Honey.
9)
Finish: Stain Color - Mocha.
10) Finish: Stain Color - Russet.
11) Finish: Painted Color (Pine) - White.
12) Finish: Painted Color (Pine) - Birch Bark.
13) Finish: Painted Color (Pine) - Prime.
6.
Sill: Fibrex material outer frame with wood core approved in AAMA/WDMA/CSA
101/I.S.2/A440.
7.
Weatherstripping:
a.
Upper Sash Head and Lower Sash Sill: Continuous bulb style, foam-filled vinyl.
b.
Upper Sash Stiles: Single bulb style, vinyl-covered, foam-filled.
c.
Lower Sash Stiles: Dual bulb style, vinyl-covered, foam-filled.
d.
Meeting Rails: Continuous bulb style, foam-filled vinyl.
H.
Hardware:
** NOTE TO SPECIFIER ** Delete if not required.
1.
Double-Hung Window Hardware:
** NOTE TO SPECIFIER ** Delete lock not required.
a.
Hardware Locks: Die-cast zinc sash locks in the following style and color:
1)
Style: Traditional.
** NOTE TO SPECIFIER ** Delete color not required.
2)
Color: Stone.
3)
Color: White.
4)
Color: Black.
5)
Color: Gold Dust.
6)
Color: Bright Brass.
7)
Color: Antique Brass.
8)
Color: Polished Chrome.
9)
Color: Brushed Chrome.
10) Color: Oil Rubbed Bronze.
11) Color: Satin Nickel.
b.
Lock and Keeper: Die-cast zinc hardware with the following style and color:
1)
Style: Traditional.
** NOTE TO SPECIFIER ** Delete color not required.
2)
Color: Stone.
3)
Color: White.
4)
Color: Black.
5)
Color: Gold Dust.
08556-9
6)
Color: Bright Brass.
7)
Color: Antique Brass.
8)
Color: Polished Chrome.
9)
Color: Brushed Chrome.
10) Color: Oil Rubbed Bronze.
11) Color: Satin Nickel.
12) Tilt mechanism integrated into lock.
** NOTE TO SPECIFIER ** Delete lift hardware not required.
c.
Finger Lift Hardware: Zinc cast with baked, powder coated finish on chromate
protective coating in the following style and color:
1)
Finger Lifts: Provide 2 per sash unit.
2)
Style: Traditional.
** NOTE TO SPECIFIER ** Delete color not required.
3)
Color: Stone.
4)
Color: White.
5)
Color: Black.
6)
Color: Gold Dust.
7)
Color: Bright Brass.
8)
Color: Antique Brass.
9)
Color: Polished Chrome.
10) Color: Brushed Chrome.
11) Color: Oil Rubbed Bronze.
12) Color: Satin Nickel.
d.
Hand Lift Hardware: Zinc die cast with baked powder coated finish on chromate
protective coating in the following style and color:
1)
Hand Lift: Provide 1 hand lift per sash unit.
2)
Style: Traditional.
** NOTE TO SPECIFIER ** Delete color not required.
3)
Color: Stone.
4)
Color: White.
5)
Color: Black.
6)
Color: Gold Dust.
7)
Color: Bright Brass.
8)
Color: Antique Brass.
9)
Color: Polished Chrome.
10) Color: Brushed Chrome.
11) Color: Oil Rubbed Bronze.
12) Color: Satin Nickel.
e.
Bar Lift Hardware: Zinc die cast with baked powder coated finish on chromate
protective coating in the following style and color:
1)
Bar Lift: Provide 1 hand lift per window unit.
2)
Style: Traditional.
** NOTE TO SPECIFIER ** Delete color not required.
3)
Color: Stone.
4)
Color: White.
5)
Color: Black.
6)
Color: Gold Dust.
7)
Color: Bright Brass.
8)
Color: Antique Brass.
9)
Color: Polished Chrome.
10) Color: Brushed Chrome.
11) Color: Oil Rubbed Bronze.
12) Color: Satin Nickel.
f.
Balancers: Fit top and bottom sash with concealed frame mounted balancers.
Design balancers to allow easy operation of double-hung units.
08556-10
** NOTE TO SPECIFIER ** Delete if design pressure (DP) upgrade is not required.
g.
DP Upgrade Window Hardware:
1)
Provide 2 retractable interior wind load brackets at check rail.
2)
Provide 2 upper check rail support brackets located on side outer frame
members. Match bracket color to exterior frame color.
3)
Provide 2 bottom rail support brackets located on the sill. Match bracket
color to exterior frame color.
** NOTE TO SPECIFIER ** Delete if not required.
2.
Awning and Venting Transom Hardware:
** NOTE TO SPECIFIER ** Select SS hinge for use when exposed to salt air or other severe
environmental or industrial areas calling for higher levels of corrosion protection. Delete hinge
not required.
a.
Hinges: Powder coated painted hinge arms with 300 Series stainless steel slide
track.
b.
Hinges: 300 Series stainless steel hinge arms with 300 Series stainless steel
slide track.
c.
Operator: Electrostatically plated rotary-type operator attached to chromeplated steel rod applied to bottom rail of sash. Single steel operator arm
stamped with gear ring. Set arm gear assembly between nylon bushing and
nylon spacer. Encase drive shaft and worm gear assembly in zinc die cast
base.
** NOTE TO SPECIFIER ** Add the following for use when exposed to salt air or other severe
environmental or industrial areas calling for higher levels of corrosion protection.
1)
Operators: 300 Series stainless steel gear arm rivet; zinc plated steel
bottom plate. Other parts plated and powder coated steel or zinc.
d.
Operator Handle and Covers:
1)
Folding Handle Hardware: Zinc die cast folding handle and cover with
powder coated painted finish.
** NOTE TO SPECIFIER ** Delete folding handle style not required.
2)
Style: Traditional.
3)
Style Contemporary
** NOTE TO SPECIFIER ** Delete color not required.
4)
Color: Stone.
5)
Color: White.
6)
Color: Black.
7)
Color: Gold Dust.
8)
Color: Bright Brass.
9)
Color: Antique Brass (Traditional style only).
10) Color: Polished Chrome (Traditional style only).
11) Color: Brushed Chrome (Traditional style only).
12) Color: Oil Rubbed Bronze.
13) Color: Satin Nickel.
** NOTE TO SPECIFIER ** Omit sash locks where remote window operators are required. Omitting
sash locks will decrease window performance. Level 20 forced entry resistance is not available
when electric operator is specified. Delete if not required.
e.
Sash Locks: Single actuation lock concealed by trim stops. Die cast zinc,
galvanized steel link and engineered polymer components in finishes to match
handle options.
** NOTE TO SPECIFIER ** Delete if not required.
f.
Provide remote window operator.
1)
Remote Awning Window Operator: Provide electric window opener for
remote operation of venting unit where indicated on Drawings consisting
of a 16 volt power operator, power supply (converting 120 V AC to 16 V
DC), pushbutton command center, rain sensor that will signal power
08556-11
operator to close unit, and necessary mounting hardware. Provide safety
connector that will not permit operation of electric window opener unless
insect screen is in place. Do not provide sash locks on windows
equipped with remote awning window operator.
** NOTE TO SPECIFIER ** Delete if not required.
3.
Venting Casement Hardware:
** NOTE TO SPECIFIER ** SS for use when exposed to salt air or other severe environmental or
industrial areas calling for higher levels of corrosion protection. Delete hinge not required.
a.
Hinges: Powder coated painted hinge arms with 300 Series stainless steel slide
track.
b.
Hinges: 300 Series stainless steel hinge arms with 300 Series stainless steel
slide track.
c.
Operators: Hardened steel operator arm stamped with a gear ring. Set arm
gear between nylon bushing and nylon spacer. Encase drive shaft and worm
gear assemblies in zinc die cast base and removable, painted, die-cast cover.
** NOTE TO SPECIFIER ** Add the following for use when exposed to salt air or other severe
environmental or industrial areas calling for higher levels of corrosion protection.
1)
Operators: 300 Series stainless steel gear arm link and clip; 300 Series
stainless steel gear arm rivet; zinc plated steel bottom plate. Other parts
plated and powder coated steel or zinc.
d.
Folding Handle: Zinc die cast handle and cover with powder coated painted
finish.
** NOTE TO SPECIFIER ** Delete folding handle style not required.
1)
Style: Traditional.
2)
Style Contemporary
** NOTE TO SPECIFIER ** Delete color not required.
3)
Color: Stone.
4)
Color: White.
5)
Color: Black.
6)
Color: Gold Dust.
7)
Color: Bright Brass.
8)
Color: Antique Brass (Traditional style only).
9)
Color: Polished Chrome (Traditional style only).
10) Color: Brushed Chrome (Traditional style only).
11) Color: Oil Rubbed Bronze.
12) Color: Satin Nickel.
e.
Lock Handle and Bezel: Universal lock handle of die cast zinc with powder
coated paint finish and polycarbonate bezel in the following color:
** NOTE TO SPECIFIER ** Delete color not required.
1)
Color: Stone.
2)
Color: White.
3)
Color: Black.
4)
Color: Gold Dust.
5)
Color: Bright Brass.
6)
Color: Antique Brass.
7)
Color: Polished Chrome.
8)
Color: Brushed Chrome.
9)
Color: Oil Rubbed Bronze.
10) Color: Satin Nickel.
f.
Sash Locks: Single actuation lock concealed by trim stops. Die cast zinc,
galvanized steel link and engineered polymer components.
I.
Accessories
** NOTE TO SPECIFIER ** Delete if not required.
08556-12
1.
Sill Stool: Wood members machined from clear material or veneered finger joined
material approved in AAMA/WDMA/CSA 101/I.S.2/A440.
** NOTE TO SPECIFIER ** Delete if not required.
2.
Extension Jambs: Wood members machined from clear material or veneered finger
joined material. Pre-drill extension jambs for application. Factory-applied extension
jambs are available in 1/16 inch (1.6 mm) depth increments ranging from 5-1/4 inch
(133 mm) depth to 7-1/8 inch (181 mm).
** NOTE TO SPECIFIER ** Delete if not required.
3.
Exterior Trim and Casing: Where indicated on Drawings, provide trim attached to
attachment strip.
a.
Color: Match window framing unless indicated otherwise. Refer to Exterior
Finish Schedule.
** NOTE TO SPECIFIER ** Typical trim combination styles. Delete styles not required.
b.
Trim Style: Flat trim with extended head and extended sill.
c.
Trim Style: Flat trim with flush head and extended sill.
d.
Trim Style: Brick mould with extended sill.
e.
Trim Style: Flat trim with decorative drip cap and extended sill.
f.
Trim Style: Flat trim with 2 inches (51 mm) cornice and extended sill.
g.
Trim Style: Flat trim with 3-5/8 inches (92 mm) cornice and extended sill.
h.
Profiles: Fibrex material.
** NOTE TO SPECIFIER ** Delete trim not required.
1)
Flat Trim Width: 3-1/2 inch (89 mm) by 1 1/2 inches (38 mm) deep.
2)
Flat Trim Width: 4 1/2 inches (114 mm) by 1 1/2 inches (38 mm) deep.
3)
Brick Mould: 2 inch (51 mm) wide by 1 5/8 inches (41 mm) deep.
4)
Sill Nose: 1 15/16 inches (49 mm) wide by 1 7/8 inches (48 mm) deep.
5)
Mull Cover: 4-1/4 inch (108 mm) wide by 1 1/2 inches (38 mm) deep.
** NOTE TO SPECIFIER ** Mull cover above is for face. Mull cover below is for pockets.
6)
Mull Cover: 3-3/4 inch (95 mm) wide by 1 1/2 inches (38 mm) deep.
i.
Profiles: Molded Urethane.
** NOTE TO SPECIFIER ** Delete trim not required.
1)
Cornice: 3 5/8 inches (92 mm) high by 4 inches (102 mm) deep.
2)
Cornice: 2 inches (51 mm) high by 3 1/4 inches (83 mm) deep.
3)
Decorative Drip Cap: 15/16 inches (24 mm) high by 2 1/4 inches (57
mm) deep.
** NOTE TO SPECIFIER ** Andersen bay windows can be wall supported or suspended. The cable
support system is required when units are to be suspended. Each cable is capable of supporting a
maximum load of 500 lb (227 kg). Additional support is necessary if the section of the window unit
requiring support exceeds 500 lb (227 kg). Radius top windows cannot be use as bay windows.
4.
Cable Support System: 1/8 inch (3.2 mm) diameter braided steel cable with hardware
required for complete installation.
** NOTE TO SPECIFIER ** Delete if not required.
J.
Insect Screens
** NOTE TO SPECIFIER ** Delete insect screen not required.
1.
Insect Screens: Provide venting sash with an insect screen, including attachment
hardware.
a.
Insect Screen Cloth: 18 by 16 (1.0 by 1.1 mm) count per sq. inch aluminum
mesh, gunmetal finish.
** NOTE TO SPECIFIER ** Delete frame not required.
b.
Frames: Full height 0.024 inch (0.61 mm) rolled aluminum frame with chromate
conversion coating. Provide matching corner locks and latch retainers.
c.
Frames: Half height 0.024 inch (0.61 mm) rolled aluminum frame with chromate
conversion coating. Provide matching corner locks and latch retainers.
08556-13
d.
Frame Finish: High-bake polyester finish in the following color:
** NOTE TO SPECIFIER ** Delete color not required.
1)
Color: White.
2)
Color: Stone.
3)
Color: Gold Dust.
4)
Color: Sandtone.
5)
Color: Terratone.
6)
Color: Forest Green.
7)
Color: Canvas.
8)
Color: Dove Gray.
9)
Color: Prairie Grass.
10) Color: Red Rock.
11) Color: Cocoa Bean.
12) Color: Dark Bronze.
13) Color: Black.
2.
Insect Screen: Provide TruScene at venting sash with attachment hardware.
a.
Insect Screen Cloth: 25 by 25 count per square inch (9.84252 per sq cm) micro
fine stainless steel wire with a polyester non-reflective coating.
** NOTE TO SPECIFIER ** Delete frame not required.
b.
Frames: Full height 0.024 (0.61 mm) inch rolled aluminum frame with chromate
conversion coating and polyester painted finish.
c.
Frames: Half height 0.024 (0.61 mm) inch rolled aluminum frame with chromate
conversion coating and polyester painted finish.
d.
Frame Finish: Polyester finish in the following color:
** NOTE TO SPECIFIER ** Delete color not required.
1)
Color: White.
2)
Color: Stone.
3)
Color: Gold Dust.
4)
Color: Sandtone.
5)
Color: Terratone.
6)
Color: Forest Green.
7)
Color: Canvas.
8)
Color: Dove Gray.
9)
Color: Prairie Grass.
10) Color: Red Rock.
11) Color: Cocoa Bean
12) Color: Dark Bronze.
13) Color: Black.
e.
Wood Frames for Awning, Casement and Venting Transom Window Insect
Screens: Full height.
** NOTE TO SPECIFIER ** Delete wood species not required.
1)
Species: Pine.
2)
Species: Oak.
3)
Species: Maple.
** NOTE TO SPECIFIER ** Delete wood finish not required.
4)
Finish: Unfinished.
5)
Finish: Clear coat finish.
6)
Finish: Stain Color - Cinnamon.
7)
Finish: Stain Color - Espresso.
8)
Finish: Stain Color - Honey.
9)
Finish: Stain Color - Mocha.
10) Finish: Stain Color - Russet.
11) Match window interior unit wood species and finish.
K.
Fabrication
08556-14
1.
Preservative Treatment: Treat wood sash and frame members after machining with a
water repellent preservative per WDMA I.S.4.
** NOTE TO SPECIFIER ** Delete if not required..
2.
Double-Hung, Casement, Awning, Venting Transom Units:
** NOTE TO SPECIFIER ** Extruded Fibrex is required to produce radius top units, transom and
picture windows. Delete outer frame not required.
a.
Outer Frame: Fibrex material laminated to wood core with PVC end caps.
b.
Outer Frame (Radius Units): Extruded Fibrex material adhesively bonded
corner keys. Mechanically fasten sill assembly and wood sub-frame
components. Bond outer frame members to sub-frame with adhesive and
mechanical fasteners.
c.
Sill: Fibrex material.
d.
Bond outer frame members and sill to wood base frame with adhesive.
** NOTE TO SPECIFIER ** Delete Jamb and Head Jamb Liners not required.
e.
Jamb and Head Jamb Liners (Pine):
1)
Side Jamb Liner: Solid pine filler attached to a rigid PVC vinyl extrusion.
2)
Head Jamb Liner: Solid pine head parting stop and interior aesthetic filler
with rigid PVC vinyl head liner.
f.
Jamb and Head Jamb Liners (Oak and maple):
1)
Side Jamb Liner: Oak or maple veneer over solid, finger-joined pine filler
attached to rigid PVC vinyl extrusion.
2)
Head Jamb Liner: Oak or maple veneer over solid, finger-joined pine
parting stop and interior aesthetic filler with a rigid PVC vinyl head liner.
g.
Sash Components:
1)
Exterior Sash: Pultruded fiberglass material with adhesively bonded PVC
corner keys.
2)
Interior Sash: Clear or veneer wood adhesively applied to exterior sash
components.
** NOTE TO SPECIFIER ** Delete if not required..
3.
Picture and Transom Units:
a.
Outer Frame: Pultruded fiberglass material with adhesively bonded PVC corner
keys.
b.
Interior Sash: Provide clear wood interior sash components clip fastened to
exterior sash profile.
c.
Provide clear or veneer wood stops.
d.
Mechanically fasten sill assembly and wood sub frame components. Bond outer
frame members to sub-frame with adhesive and mechanical fasteners.
4.
Glazing: Factory glazed with glazing sealant.
5.
Weatherstripping: Factory-applied to unit frame. Field-applied interlocking
weatherstripping at panel meeting stiles.
** NOTE TO SPECIFIER ** Delete if not required.
2.3
SLIDING PATIO DOORS
A.
Gliding Patio Doors:
1.
Product: Andersen® A-Series Gliding Patio Doors.
B.
Materials:
** NOTE TO SPECIFIER ** Retain Certified Wood Paragraph below if wood doors are required to be
certified for LEED or project is being designed with sustainable practices.
1.
Certified Wood: Doors shall be certified as "FSC Mixed Credit" per FSC STD-01-001,
"FSC Principles and Criteria for Forest Stewardship," and FSC STD-40-004, "FSC
Standard for Chain of Custody Certification."
2.
Wood Members: Fabricated from wood species approved in WDMA I.S.4.
3.
Reinforced engineered plastic fiberglass frame cover: Comply with ASTM D3647.
08556-15
4.
5.
6.
Urethane Coating: High durability coating conforming to color uniformity, chemical
resistance, detergent resistance, and weather resistance requirements of AAMA
2603.
Sill: Reinforced engineered plastic fiberglass
Weatherstripping:
a.
Head Jamb weatherstripping for operating panel: Polypropylene pile with fin
seal.
b.
Sill weatherstripping: Foam filled Polyethylene leaf seal.
c.
Side Jambs: Polypropylene pile with fin seal at operating side jamb and foam
filled polyethylene leaf seal at stationary side jamb.
d.
Meeting Stiles: PVC scissors interlock weatherstrip with silicone bulb primary
weatherstrip.
C.
Hardware:
1.
Roller Assembly: Provide operating panels with adjustable roller assembly consisting
of self-lubricating tandem wheels operating on ball bearings. Provide 2-tandem rollers
for each operating panel.
** NOTE TO SPECIFIER ** 6-pin key cylinder is optional. Retain, edit, or delete the following
paragraph to suit project requirements.
2.
Latch Levers: Forged brass or zinc die cast thumb-turn-operated reach- out dual
multi-point hook bolt locking mechanism. Design lock to prevent automatic locking
when door is closed.
** NOTE TO SPECIFIER ** Retain one of the following two options per project requirements.
a.
Provide blank cover at exterior.
b.
Provide 6-pin keyed cylinder.
** NOTE TO SPECIFIER ** Optional auxiliary and 6-pin key cylinder exterior keyed locks shipped
separately.
** NOTE TO SPECIFIER ** Select between the following hardware styles. Delete styles not required
for project.
3.
Hardware Styles: Provide the following hardware where indicated:
a.
Newbury® Hardware: Forged brass thumb turn and operating handle pull with
the following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware lock finishes below. Delete
finishes not required.
1)
Finish: Bright Brass.
2)
Finish: Antique Brass.
3)
Finish: Polished Chrome.
4)
Finish: Brushed Chrome.
5)
Finish: Oil Rubbed Bronze.
6)
Finish: Satin Nickel.
b.
Metro™ Hardware: Cast zinc dichromate thumb turn and operating handle
pull with powder coated painted finish in the following color:
** NOTE TO SPECIFIER ** Retain one of the following hardware colors below. Delete colors not
required.
1)
Color: White.
2)
Color: Stone.
c.
Covington™ Hardware: Forged brass thumb turn and operating handle
pull with the following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Bright Brass.
2)
Finish: Antique Brass.
3)
Finish: Oil Rubbed Bronze.
d.
Encino® Hardware: Forged brass thumb turn and operating handle pull with the
08556-16
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Distressed Bronze.
2)
Finish: Distressed Nickel.
e.
Yuma® Hardware: Forged brass thumb turn and operating handle pull with the
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Distressed Bronze.
2)
Finish: Distressed Nickel.
f.
Anvers® Hardware: Forged brass thumb turn and operating handle pull with the
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete colors not
required.
1)
Finish: Bright Brass.
2)
Finish: Oil Rubbed Bronze.
3)
Finish: Satin Nickel.
g.
Whitmore® Hardware: Forged brass thumb turn and operating handle pull with
the following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Bright Brass.
2)
Finish: Antique Brass.
3)
Finish: Oil Rubbed Bronze.
4)
Finish: Satin Nickel.
h.
Albany® Hardware: Cast zinc dichromate thumb turn and lever handle trim with
powder coated painted finish in the following color:
** NOTE TO SPECIFIER ** Retain one of the following hardware colors below. Delete colors not
required.
1)
Color: Gold Dust.
2)
Color: White.
3)
Color: Black.
4)
Color: Stone.
** NOTE TO SPECIFIER ** Auxiliary foot locks are optional on 2 and 4 panel doors. Delete
paragraph if not required.
4.
Auxiliary Foot Lock: Provide operating panels with auxiliary foot lock consisting of a
spring loaded plunger that engages in a grommet in the sill. Provide auxiliary foot
locks in the following finish or color:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes or colors below. Delete
finishes or colors not required.
a.
Finish: Bright Brass.
b.
Finish: Antique Brass.
c.
Finish: Polished Chrome.
d.
Finish: Brushed Chrome.
e.
Finish: Oil Rubbed Bronze.
f.
Finish: Satin Nickel.
g.
Finish: Distressed Bronze.
h.
Finish: Distressed Nickel.
i.
Color: Stone.
j.
Color: White.
k.
Color: Gold dust.
** NOTE TO SPECIFIER ** Specify subordinate or secondary items that aid and assist primary
products specified above or are necessary for preparation or installation of those items.
08556-17
D.
Accessories:
1.
Provide wood interior extension jamb members machined from clear or veneered,
finger joined clear material approved in ANSI/AAMA/NWWDA 101/I.S.2. Pre-drill
extension jambs for application.
2.
Exterior Trim and Casing: Where indicated on Drawings, provide Fibrex® material in
the following thickness, conforming to NIST Voluntary Product Standards P.S.1 and
rigid vinyl channels.
a.
Thickness: 1/2 inch (13 mm).
b.
Color: Match patio door framing.
c.
Andersen® Fibrex material trim kits:
** NOTE TO SPECIFIER ** Retain one of the following widths below.
1)
Trim Width: 3-1/2 inches (89 mm) Flat.
2)
Trim Width: Brickmold.
** NOTE TO SPECIFIER ** Retain subparagraph above for Andersen® vinyl trim board. retain
subparagraph below for vinyl laminated board.
d.
Support Mullion Trim: 2 inch (51 mm) wide wood filler and vinyl trim strip.
1)
Color: Match door unit exterior color.
E.
Insect Screens:
** NOTE TO SPECIFIER ** Select between the gliding or retractable Insect screen options.
1.
Gliding Insect Screens: Provide gliding patio doors with gliding insect screen installed
on exterior.
a.
Insect Screen Door Frame: 0.040 inch (1 mm) roll formed aluminum frame with
chromate conversion coating in the following polyester painted color.
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
1)
Color: White.
2)
Color: Sandtone.
3)
Color: Terratone® .
4)
Color: Forest Green
5)
Color: Black
6)
Color: Coco Bean
7)
Color: Dove Grey
8)
Color: Canvas
9)
Color: Red Rock
10) Color: Prairie Grass
11) Color: Dark Bronze
b.
Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
c.
Rollers: Insect screen doors operate on injection molded bottom rollers with self
contained leveling adjusters engaged in sill track.
d.
Operating Handles: Polycarbonate operating handles to receive locking
mechanism in the following color.
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
1)
Color: White.
2)
Color: Stone.
3)
Color: Black
4)
Color: Coco Bean
5)
Color: Dove Grey
6)
Color: Canvas
7)
Color: Red Rock
8)
Color: Prairie Grass
9)
Color: Dark Bronze
2.
Retractable Insect Screens: Provide gliding patio doors with retractable insect screen
installed on exterior.
08556-18
a.
Insect Screen Door Housing: Extruded aluminum housing in the following color.
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
1)
Color: White.
2)
Color: Sandtone.
3)
Color: Terratone® .
4)
Color: Forest Green finish.
5)
Color: Black
6)
Color: Coco Bean
7)
Color: Dove Grey
8)
Color: Canvas
9)
Color: Red Rock
10) Color: Prairie Grass
11) Color: Dark Bronze
b.
Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
3.
Top Hung Gliding Insect Screens: Provide gliding patio doors with gliding insect
screen installed on exterior.
a.
Insect Screen Door Frame: 0.040 inch (1 mm) roll formed aluminum frame with
chromate conversion coating in the following polyester painted color.
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
1)
Color: White.
2)
Color: Sandtone.
3)
Color: Terratone® .
4)
Color: Forest Green finish.
5)
Color: Black
6)
Color: Coco Bean
7)
Color: Dove Grey
8)
Color: Canvas
9)
Color: Red Rock
10) Color: Prairie Grass
11) Color: Dark Bronze
b.
Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
** NOTE TO SPECIFIER ** Describe items that must be shop manufactured, fabricated, or
assembled before being delivered to the site.
F.
Fabrication:
1.
Preservative Treatment: Treat wood frame and door panel wood members after
machining with a water repellent preservative per WDMA I.S.4.
2.
Frame Components:
a.
Corner Fastening: Dual dowel and water resistant structural adhesive.
b.
Attach reinforced engineered plastic frame cover to wood frame.
c.
Factory-apply urethane coating (2.6 mil minimum dry film thickness) to exterior
exposed surfaces of sensitized, reinforced, engineered plastic frame cover.
3.
Door Panels:
a.
Stiles: 1-1/2 inch (38 mm) LVL wood core. Provide solid wood edge strips,
phenolic interior and exterior outer substrate, and spliced veneer interior
surface.
1)
8 foot (2438 mm) units use laminated veneer lumber core.
b.
Top Rails: Solid, clear material or finger joined and edge glued wood core.
Provide solid wood edge strips, phenolic interior and exterior outer substrate,
and spliced veneer interior surface.
c.
Bottom Rails: Laminated construction consisting of spliced veneer interior
surface over laminated veneer lumber core with phenolic overlay interior and
exterior outer substrate.
08556-19
d.
Panel Finish:
** NOTE TO SPECIFIER ** Retain appropriate option below or change to change to project staining
section.
1)
Interior: Unfinished, natural clear veneer of the following species to
receive field applied paint or stain finish as specified in the painting
section.
2)
Interior: Natural clear veneer of the following species shall be
prefinished.
** NOTE TO SPECIFIER ** Retain project required veneer subparagraph below. Delete
subparagraphs not required.
a)
Species: Oak.
b)
Species Type: Maple.
c)
Species Type: Pine.
d)
Finish Type: Water based
1)
Prefinished Painted White Pine interior.
2)
Prefinished Painted Birch Bark interior.
3)
Prefinished Painted Prime interior.
4)
Prefinished stained clear coat interior.
5)
Prefinished stained Honey interior.
6)
Prefinished stained Cinnamon interior.
7)
Prefinished stained Russet interior.
8)
Prefinished stained Mocha interior.
9)
Prefinished stained Espresso interior.
3)
Exterior: Factory-applied, high durability, urethane coating in the
following color:
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
a)
Color: White.
b)
Color: Sandtone.
c)
Color: Terratone® .
d)
Color: Forest Green finish.
e)
Color: Black.
f)
Color: Coco Bean.
g)
Color: Dove Grey.
h)
Color: Canvas.
i)
Color: Red Rock.
j)
Color: Prairie Grass.
k)
Color: Dark Bronze.
4.
Weatherstripping: Factory-applied to unit frame. Field-apply interlocking
weatherstripping at panel meeting stiles.
5.
Glazing: Factory-glazed with glazing sealant and wood interior trim stops.
** NOTE TO SPECIFIER ** Delete if not required.
2.4
HINGED PATIO DOORS
A.
Proprietary Products/Systems:
** NOTE TO SPECIFIER ** Delete door type not required.
1.
Product: Andersen® A-Series Hinged Patio Doors.
2.
Product: Andersen® A-Series Outswing Patio Doors.
3.
Product: Andersen® A-Series Patio Door Sidelights.
4.
Product: Andersen® A-Series Patio Door Transoms.
** NOTE TO SPECIFIER ** Specify materials to be furnished. This article may be omitted and the
materials can be included with the description of a manufactured unit, equipment, component, or
accessory.
08556-20
B.
Materials:
** NOTE TO SPECIFIER ** Retain Certified Wood Paragraph below if wood doors are required to be
certified for LEED or project is being designed with sustainable practices.
1.
Certified Wood: Doors shall be certified as "FSC Mixed Credit" per FSC STD-01-001,
"FSC Principles and Criteria for Forest Stewardship," and FSC STD-40-004, "FSC
Standard for Chain of Custody Certification."
2.
Wood Members: Fabricated from wood species approved in WDMA I.S.4.
3.
Reinforced engineered plastic fiberglass frame cover: Comply with ASTM D3647.
4.
Urethane Coating: Durable coating conforming to color uniformity, chemical
resistance, detergent resistance, and weather resistance requirements of AAMA
2603.
5.
Weatherstripping: Continuous, flexible, compressible bulb type with welded corners.
6.
Sill: Reinforced engineered plastic fiberglass.
C.
Hardware:
1.
Hinges: Ball bearing, adjustable, captured hinge design with cover plate. Hinges allow
vertical and rack panel adjustment, in the following finish to match lock trim:
** NOTE TO SPECIFIER ** Retain one of the following hardware lock colors below. Delete colors
not required.
a.
Finish: Bright Brass.
b.
Finish: Antique Brass.
c.
Finish: Polished Chrome.
d.
Finish: Brushed Chrome.
e.
Finish: Oil Rubbed Bronze.
f.
Finish: Satin Nickel.
g.
Finish: Distressed Bronze.
h.
Finish: Distressed Nickel.
i.
Finish: Gold Dust.
j.
Finish: Black.
2.
Hinges for Doors with Prefinished White Interior: Prefinished White zinc die cast.
a.
Other interior finished or unfinished doors will default to Gold Dust colored
hinges, steel adjustable, captured hinge design with ball bearing pivots.
3.
Locks: Stainless steel locking mechanism consisting of lever handle operated latch
and 3-point deadbolt lock mechanism. 3-point locking mechanism consists of thumb
turn operated 0.787 inch (20 mm) metal deadbolt, which when projected, locks 2
additional hook bolts engaging active panel.
a.
Provide 6-pin keyed cylinder and thumb turn at interior.
4.
Coastal Upgrade for AP/PA Units: 5-point stainless steel lock.
5.
Lever Handle Trim: Provide the following trim style and finish where indicated:
** NOTE TO SPECIFIER ** Select between the following hardware styles.
a.
Newbury® Hardware: Forged brass thumb turn and operating handle pull with
the following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Bright Brass.
2)
Finish: Antique Brass.
3)
Finish: Polished Chrome.
4)
Finish: Brushed Chrome.
5)
Finish: Oil Rubbed Bronze.
6)
Finish: Satin Nickel.
b.
Covington™ Hardware: Forged brass thumb turn and operating handle
pull with the following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Bright Brass.
08556-21
2)
Finish: Antique Brass.
3)
Finish: Oil Rubbed Bronze.
c.
Encino® Hardware: Forged brass thumb turn and operating handle pull with the
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Distressed Bronze.
2)
Finish: Distressed Nickel.
d.
Yuma® Hardware: Forged brass thumb turn and operating handle pull with the
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Distressed Bronze.
2)
Finish: Distressed Nickel.
e.
Anvers® Hardware: Forged brass thumb turn and operating handle pull with the
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Bright Brass.
2)
Finish: Oil Rubbed Bronze.
3)
Finish: Satin Nickel.
f.
Whitmore®: Forged brass thumb turn and operating handle pull with the
following finish:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Finish: Bright Brass.
2)
Finish: Antique Brass.
3)
Finish: Oil Rubbed Bronze.
4)
Finish: Satin Nickel.
g.
Tribeca Hardware: Cast zinc dichromate thumb turn and lever handle trim with
powder coated painted finish in the following color:
** NOTE TO SPECIFIER ** Retain one of the following hardware finishes below. Delete finishes not
required.
1)
Color: White.
2)
Color: Stone.
** NOTE TO SPECIFIER ** Specify subordinate or secondary items that aid and assist primary
products specified above or are necessary for preparation or installation of those items.
D.
Accessories:
1.
Exterior Trim and Casing: Where indicated on Drawings, provide vinyl sheathed
plywood in the following thickness, conforming to NIST Voluntary Product Standards
P.S.1 and rigid vinyl channels.
a.
Thickness: 1/2 inch (12.7 mm).
** NOTE TO SPECIFIER ** Retain thickness above or below.
b.
Thickness: 3/4 inch (19 mm).
c.
Color: Match door framing.
d.
Vinyl Trim Board: 0.043 inch (1.09 mm) thick vinyl with lightly textured surface
laminated with adhesive to 3/4 inch (19 mm) thick plywood.
** NOTE TO SPECIFIER ** Retain subparagraph above for Andersen® vinyl trim board. Retain
subparagraph below for vinyl laminated board.
e.
Vinyl Laminated Board: 0.045 inch (1.14 mm) thick vinyl with smooth surface
laminated with adhesive to 1/2 inch (12.7 mm) thick plywood.
f.
Trim Channels: Rigid vinyl extrusions furnished by door manufacturer for use
on same product line.
08556-22
g.
Jamb Depth:
1)
Inswing 4-9/16 inches and 6 9/16 inch (116 mm).
2)
Outswing 4-9/16 inches (116 mm).
3)
Sidelights and Transoms 4-9/16 inches (116 mm).
2.
Interior Extension Jambs: Solid or veneered wood in the following species and depths:
** NOTE TO SPECIFIER ** Retain project required species subparagraph below and delete
subparagraphs not required.
a.
Species: Maple.
b.
Species: Pine.
c.
Species: Oak.
d.
Species: Prefinished Pine.
** NOTE TO SPECIFIER ** Retain project required jamb width subparagraph below and delete
subparagraphs not required.
e.
Jamb Width: Available in 1/16 inch (1.6 mm) depths up to 7-1/8 inches (181
mm):
3.
A-Series Outswing Door Panel Stop: Provide panel stops fabricated from the following
species:
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
a.
Species: Pine.
b.
Species: Oak.
c.
Species: Maple.
d.
Species: Painted.
4.
A-Series Hinged Inswing and Outswing Door Threshold: Provide threshold fabricated
from the following species:
a.
Species: Oak.
** NOTE TO SPECIFIER ** Retain species above or below.
b.
Species: Mahogany.
5.
Exterior Keyed Lock: 6-pin keyed lock system.
6.
Support Mullion Trim: 2 inch (51 mm) wide wood filler and vinyl trim strip.
a.
Color: Match door unit exterior color.
7.
Provide wood interior extension jamb members machined from clear or veneered,
finger joined clear material approved in ANSI/AAMA/NWWDA 101/I.S.2. Pre-drill
extension jambs for application.
E.
Insect Screens:
1.
Hinged Door Insect Screens: Provide hinged patio doors with an insect screen
installed on exterior.
a.
Insect Screen Door Frame: 0.040 inch (1.02 mm) roll formed aluminum frame
with chromate conversion coating.
b.
Hinged Insect Screen Door Frame for Single Panel and Active Passive Units:
0.040 inch (1.02 mm) extruded aluminum frame with chromate conversion
coating. Provide hinged insect screen doors complete with hinges, closers, and
latches.
c.
Double-Hinged Insect Screen: 0.040 inch (1.02 mm) aluminum frame with
chromate conversion coating.
1)
Perma-Clean® Top Hung Gliding Insect Screens: Provide Inswing
hinged patio doors with gliding insect screen installed on exterior for
Active Stationary or 3 panel configurations.
d.
Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
e.
Frame Finish:
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
1)
Color: White.
2)
Color: Sandtone.
08556-23
3)
Color: Terratone® .
4)
Color: Forest Green.
5)
Color: Cocoa Bean.
6)
Color: Red Rock.
7)
Color: Black.
8)
Color: Prairie Grass.
9)
Color: Canvas.
10) Color: Dove Grey.
f.
Rollers: Insect screen doors operate on injection molded bottom rollers with self
contained leveling adjusters engaged in sill track.
g.
Operating Handles: Polycarbonate operating handles to receive locking
mechanism in the following color.
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. delete
subparagraphs not required. "Polane" is a registered trademark of the Sherwin-Williams
Company.
1)
Color: White.
2)
Color: Stone.
3)
Color: Forest Green.
4)
Color: Cocoa Bean.
5)
Color: Red Rock.
6)
Color: Black.
7)
Color: Prairie Grass.
8)
Color: Canvas.
9)
Color: Dove Grey.
h.
Polane® coating, 6063 aluminum extrusion with corner locks and drive rivet
fastening system.
i.
Color: Match patio door unit exterior color.
2.
Outswing Door Insect Screens: Provide outswing hinged patio doors with retractable
insect screen installed on interior jamb.
a.
Retractable Insect Screen Housing Assembly: Aluminum with white painted
finish.
b.
Insect Screen Cloth: 18 by 16 glass fiber mesh, charcoal color finish.
** NOTE TO SPECIFIER ** Describe items that must be shop manufactured, fabricated, or
assembled before being delivered to the site.
F.
Fabrication:
1.
Preservative Treatment: Treat wood frame and door panel wood members after
machining with water repellent preservative per WDMA I.S.4.
2.
Frame Components:
a.
Attach reinforced engineered plastic frame cover to wood frame.
b.
Factory-applied urethane coating (2.6 mil minimum dry film thickness) to
exterior exposed surfaces of sensitized, reinforced, engineered plastic frame
cover.
3.
Door Panels:
a.
Stiles and Top Rails: Finger joined and edge glued wood core or LVL, 1-3/4
inches (44 mm) thick before milling. Provide solid wood edge strips, phenolic
interior and exterior outer substrate, and veneered interior surface.
b.
Bottom Rails: Laminated construction consisting of veneer interior surface over
laminated veneer lumber core with phenolic overlay interior and exterior outer
substrate.
c.
Corner Fastening:
1)
Door Units: Joint/corners are secured with hardwood dowels and waterresistant structural adhesive.
2)
Sidelight and Transom Units: Multi-surface butt joint with adhesive,
silicone and 2 wood screws.
08556-24
d.
Door Panel Finish:
** NOTE TO SPECIFIER ** Retain appropriate option below or change to change to project staining
section.
1)
Interior: Unfinished, natural clear veneer of the following species to
receive field applied paint or stain finish as specified in the painting
section.
2)
Interior: Natural clear veneer of the following species shall be
prefinished.
** NOTE TO SPECIFIER ** Retain project required veneer subparagraph below. Delete
subparagraphs not required.
a)
Species: Oak.
b)
Species: Maple.
c)
Species: Pine.
d)
Finish Type: Prefinished water based Painted or Stained interior.
1)
Prefinished Painted White Pine interior.
2)
Prefinished Painted Birch Bark interior.
3)
Prefinished Painted Prime interior.
4)
Prefinished stained clear coat interior.
5)
Prefinished stained Honey interior.
6)
Prefinished stained Cinnamon interior.
7)
Prefinished stained Russet interior.
8)
Prefinished stained Mocha interior.
9)
Prefinished stained Espresso interior.
3)
Exterior: Factory-applied, high durability, urethane coating in the
following color:
** NOTE TO SPECIFIER ** Retain project required color subparagraph below. Delete
subparagraphs not required.
a)
Color: White.
b)
Color: Sandtone.
c)
Color: Terratone® .
d)
Color: Forest Green.
e)
Color: Cocoa Bean.
f)
Color: Red Rock.
g)
Color: Black.
h)
Color: Prairie Grass.
i)
Color: Canvas.
j)
Color: Dove Grey finish.
4.
Sill: Reinforced Engineered Plastic "Fiberglass".
5.
Weatherstripping: Factory-applied to panel.
6.
Glazing: Factory-glazed with silicone glazing and interior wood glazing stops.
** NOTE TO SPECIFIER ** Select glass and grilles for windows and doors selected for project.
Delete provisions not required for project.
2.5
GLAZING AND GRILLES
A.
Glazing:
1.
General: Tempered insulating glass units certified through the Insulating Glass
Certification Council as conforming to the requirements of IGCC. Provide dual sealed
units consisting of polyisobutylene primary seal and silicone secondary seal. Provide
metal spacers with bent or soldered corners.
** NOTE TO SPECIFIER ** Retain certification requirements paragraph above or below.
2.
General: Tempered insulating glass units certified through the Insulating Glass
Manufacturers Association of Canada (IGMAC) conforming to the requirements of
Canadian General Standards Board CAN/CGSB 12.8 or ASTM E2190. Provide dual
sealed units consisting of polyisobutylene primary seal and silicone secondary seal.
08556-25
Provide metal spacers with bent or soldered corners.
** NOTE TO SPECIFIER ** Select between the following standard glazing options. Consult
Andersen Corporation for additional glazing options. Consult Andersen Corporation for
assistance in selecting appropriate glazing type.
3.
High-Performance™ Low-E4® Argon Gas Blend Filled Insulating Glass Units:
a.
Glass: Tempered insulating glass units consisting of an outboard and inboard
lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3,
Kind FT.
b.
Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No.
1 surface.
c.
High-Performance Low-E4 Glass Coating: Magnetron sputtering vapor
deposition (MSVD) Low-E coating applied to the No. 2 surface.
d.
Filling: Fill space between glass lites with argon gas blend.
e.
Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
4.
High-Performance Low-E4 Sun Glass, Low SHGC, Argon Gas Blend Filled Insulating
Glass Units:
a.
Glass: Tempered insulating glass units consisting of an outboard and inboard
lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3,
Kind FT.
b.
Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No.
1 surface.
c.
High-Performance Low-E4 Sun Glass Coating: Magnetron sputtering vapor
deposition (MSVD) Low-E coating applied to the No. 2 surface.
d.
Filling: Fill space between glass lites with argon gas blend.
e.
Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
5.
SmartSun™ Low-E Glass, Low SHGC, Argon Gas Blend Filled Insulating Glass
Units:
a.
Glass: Tempered insulating glass units consisting of an outboard and inboard
lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3,
Kind FT.
** NOTE TO SPECIFIER ** Where patterned glass is required for project, delete paragraph above
and retain paragraph below with appropriate patterned glass type. Delete types not required for
project.
b.
Glass: Tempered insulating glass units consisting of an outboard lite of clear
tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT and
the following patterned glass:
c.
Inboard Pattern Glass Lite:
1)
Cascade.
2)
Fern.
3)
Obscure.
4)
Reed.
d.
Air Space: 3/4 inch (19 mm).
e.
SmartSun™ Low-E Glass Coating: Magnetron sputtering vapor deposition
(MSVD) Low-E coating applied to the No. 2 surface.
f.
Filling: Fill space between glass lites with argon gas blend.
6.
High-Performance™ Low-E4® SmartSun Glass, Low SHGC, Argon Gas Blend
Filled Insulating Glass Units:
a.
Glass: Tempered insulating glass units consisting of an outboard and inboard
lite of clear tempered glass conforming to ASTM C1048, Type 1, Class 1, q3,
Kind FT.
** NOTE TO SPECIFIER ** Where patterned glass is required for project, delete paragraph above
and retain paragraph below with appropriate patterned glass type. Delete types not required for
project.
b.
Glass: Tempered insulating glass units consisting of an outboard lite of clear
tempered glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT and
08556-26
the following patterned glass:
Inboard Pattern Glass Lite:
1)
Cascade.
2)
Fern.
3)
Obscure.
4)
Reed.
d.
Air Space: 3/4 inch (75 mm).
e.
Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No.
1 surface.
f.
High-Performance Low-E4 Sun Glass Coating: Magnetron sputtering vapor
deposition (MSVD) Low-E coating applied to the No. 2 surface.
g.
Filling: Fill space between glass lites with argon gas blend.
h.
Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
** NOTE TO SPECIFIER ** Select between the two impact resistant glass types if impact resistant
glazing required.
7.
Monolithic Impact Glass:
a.
Impact Resistant Glazing: Provide impact resistant glazing that has been tested
per ASTM E1996 large missile impact requirements.
b.
Glass: Impact resistant glass consisting of two (2) lites of clear annealed glass
conforming to ASTM C1036, Type 1, Class 1, q3, Kind LA, laminated with
0.090 inch (2.3 mm) polyvinyl butyral interlayer in the following color:
** NOTE TO SPECIFIER ** Retain project required color below. Delete colors not required.
1)
Color: Clear.
2)
Color: Gray tinted.
c.
Protective removable polyolefin film applied to glass surfaces No. 1 and No. 2.
8.
Insulating Impact Resistant Glass:
a.
Impact Resistant Glazing: Provide impact resistant glazing that has been tested
per ASTM E1996 large missile impact requirements.
b.
Glass: Insulating glass units consisting of an outboard lite of clear tempered
glass conforming to ASTM C1048, Type 1, Class 1, q3, Kind FT, and a
laminated inboard lite of cleared annealed glass conforming to ASTM C1036,
Type 1, Class 1, q3, Kind LA, laminate with a 0.090 inch (2.3 mm) polyvinyl
butyral interlayer.
c.
Magnetron sputtering vapor deposition (MSVD) TiO2 coating applied to the No.
1 surface.
d.
High-Performance Low-E4 Coating: Magnetron sputtering vapor deposition
(MSVD) Low-E coating applied to the No. 2 surface.
** NOTE TO SPECIFIER ** Retain subparagraph above for standard low-e coating. Retain
subparagraph below for sun low-e coating.
e.
High-Performance™ Low-E4® Sun Glass: Magnetron sputtering vapor
deposition (MSVD) Low-E coating applied to the No. 2 surface.
f.
Filling: Fill space between glass lites with argon gas blend.
g.
Protective removable polyolefin film applied to glass surfaces No. 1 and No. 4.
c.
B.
Grilles:
** NOTE TO SPECIFIER ** Interior grilles can be fixed or permanently applied Fibrex® material or
wood as selected below. Fixed interior grilles must be used in conjunction with fixed exterior
grilles. Consult specifications for grille material of adjacent unit for joined units of different types.
Consult an Andersen representative for additional grille options.
** NOTE TO SPECIFIER ** Coordinate specifications for grille material of adjacent unit for joined
units of different types. Refer to Andersen® Divided Light Pattern Guide for available divided light
patterns and details. Exterior and interior colors can be different colors. Retain project required
grille pattern subparagraph below and delete subparagraphs not required. Full divided light and
Finelight grilles are not available for impact resistant glazed products.
1.
Full Divided Light Grilles: Fixed exterior and interior grilles with an anodized aluminum
08556-27
muntin bar, 1/2 inch (13 mm) wide, to match spacer within insulated glass unit where
indicated on Drawings.
a.
Exterior Grille: Provide Fibrex material exterior grilles where indicated on
Drawings. Install grilles on exterior of glass with adhesive tape to simulate true
divided light muntin bars in the following color:
1)
Color: White.
2)
Color: Stone.
3)
Color: Sandtone.
4)
Color: Forest Green.
5)
Color: Black.
6)
Color: Coco Bean.
7)
Color: Dove Grey.
8)
Color: Canvas.
9)
Color: Red Rock.
10) Color: Prairie Grass.
11) Color: Dark Bronze
12) Color: Terratone.
b.
Fixed Interior grille: Provide profiled wood grilles applied with adhesive tape to
interior glass surface.
1)
Grille Type: Unfinished Maple.
2)
Grille Type: Unfinished Oak.
3)
Grille Type: Unfinished Pine.
4)
Grille Type: White Fibrex material.
5)
Grille Type: Primed wood.
6)
Grille Type: Finished wood.
a)
Finished Wood Type: Oak.
b)
Finished Wood Type: Pine.
c)
Finished Wood Type: Maple.
d)
Finish Color: Clear Coat.
e)
Finish Color: Honey Stain.
f)
Finish Color: Cinnamon Stain.
g)
Finish Color: Russet Stain.
h)
Finish Color: Mocha Stain.
i)
Finish Color: Espresso Stain.
j)
Finish Color: Andersen White Paint.
k)
Finish Color: Birch Bark Paint.
** NOTE TO SPECIFIER ** Retain project required grille width subparagraph below. Delete
subparagraphs not required.
c.
Width: 3/4 inch (19 mm).
d.
Width: 7/8 inch (22 mm).
e.
Width: 1-1/8 inches (29 mm).
f.
Width: 2-1/4 inches (57mm).
g.
Pattern as indicated on Drawings.
2.
Simulated Divided Light Grilles: Fixed exterior grilles with fixed or removable interior
grilles where indicated on Drawings.
a.
Exterior Grille: Provide Fibrex material exterior grilles where indicated on
Drawings. Install grilles on exterior of glass with continuous adhesive tape to
simulate true divided light muntin bars in the following color:
1)
Color: White.
2)
Color: Terratone.
3)
Color: Sandtone.
4)
Color: Black.
5)
Color: Coco Bean.
6)
Color: Dove Grey.
7)
Color: Canvas.
8)
Color: Red Rock.
08556-28
9)
Color: Prairie Grass.
10) Color: Forest Green.
11) Color: Dark Bronze
** NOTE TO SPECIFIER ** Retain project required interior grille subparagraph below. Delete
subparagraphs not required.
b.
Fixed Interior Grille: Provide profiled wood grilles applied with adhesive tape to
interior glass surface.
1)
Grille Type: Unfinished Maple.
2)
Grille Type: Unfinished Oak.
3)
Grille Type: Unfinished Pine.
4)
Grille Type: White Fibrex material.
5)
Grille Type: Primed wood.
6)
Grille Type: Finished wood.
a)
Finished Wood Type: Oak.
b)
Finished Wood Type: Pine.
c)
Finished Wood Type: Maple.
d)
Finish Color: Clear Coat.
e)
Finish Color: Honey Stain.
f)
Finish Color: Cinnamon Stain.
g)
Finish Color: Russet Stain.
h)
Finish Color: Mocha Stain.
i)
Finish Color: Espresso Stain.
j)
Finish Color: Andersen White Paint.
k)
Finish Color: Birch Bark Paint.
c.
Removable Interior Grilles: Provide removable, hardwood maple divided light
grilles where indicated on Drawings. Install removable grilles against interior
glass, attached with metal fasteners or integral tabs to sash.
** NOTE TO SPECIFIER ** Delete wood species not required.
1)
Species: Oak.
2)
Species: Maple.
** NOTE TO SPECIFIER ** Delete wood finish not required.
3)
Finish: Unfinished.
4)
Finish: Clear coat finish.
5)
Finish: Stain Color - Cinnamon.
6)
Finish: Stain Color - Espresso.
7)
Finish: Stain Color - Honey.
8)
Finish: Stain Color - Mocha.
9)
Finish: Stain Color - Russet.
10) Finish: Painted Color (Pine) - White.
11) Finish: Painted Color (Pine) - Birch Bark.
12) Finish: Painted Color (Pine) - Prime.
13) Match window interior unit wood species and finish.
** NOTE TO SPECIFIER ** Retain project required Grille width subparagraph below. Delete
subparagraphs not required.
d.
Width: 3/4 inch (19 mm).
e.
Width: 7/8 inch (22 mm).
f.
Width: 1-1/8 inches (29 mm).
** NOTE TO SPECIFIER ** Not available for Andersen® A-Series Windows only.
g.
Width: 2-1/4 inches (57mm).
** NOTE TO SPECIFIER ** Delete pattern not required.
h.
Pattern: As indicated on Drawings.
i.
Pattern: Colonial.
j.
Pattern: Prairie A (9 light).
k.
Pattern: Prairie (6 light).
08556-29
l.
Pattern: Specified equal light.
Removable Interior Grilles: Provide removable, hardwood maple divided light grilles
where indicated on Drawings. Install removable grilles against interior glass, attached
with metal fasteners or integral tabs to sash. Provide dual face profile to give muntin
bar appearance from both interior and exterior.
** NOTE TO SPECIFIER ** Oak not available for Andersen® A-Series Doors. Delete species not
required.
a.
Species: Oak.
b.
Species: Maple.
** NOTE TO SPECIFIER ** Retain project required exterior facing subparagraph below. Delete
subparagraphs not required.
c.
Exterior Facing: White color painted finish.
d.
Exterior Facing: Sandtone color painted finish.
e.
Exterior Facing: Terratone color painted finish.
f.
Exterior Facing: Black color painted finish.
g.
Exterior Facing: Canvas color painted finish.
h.
Exterior Facing: Dove Gray color painted finish.
i.
Exterior Facing: Red Rock color painted finish.
j.
Exterior Facing: Prairie Grass color painted finish.
k.
Exterior Facing: Cocoa Bean color painted finish.
l.
Exterior Facing: Forest Green color painted finish.
** NOTE TO SPECIFIER ** Available for Andersen® A-Series Gliding Patio Doors only.
m.
Exterior Facing. Maple grille with Dark Bronze color painted finish.
** NOTE TO SPECIFIER ** Retain project required interior facing subparagraph below. Delete
subparagraphs not required.
n.
Interior Facing: Unfinished Maple.
o.
Interior Facing: Andersen White Painted maple interior.
** NOTE TO SPECIFIER ** Below available for Andersen® A-Series Doors only.
p.
Interior Facing: Birch Bark Painted maple interior.
q.
Interior Facing: Prime Painted maple interior.
r.
Interior Facing: Painted maple interior.
s.
Interior Facing: Clear Coat stain maple interior.
t.
Interior Facing: Honey stain maple interior.
u.
Interior Facing: Cinnamon stain maple interior.
v.
Interior Facing: Russet stain maple interior.
w.
Interior Facing: Mocha stain maple interior.
x.
Interior Facing: Espresso stain maple interior.
** NOTE TO SPECIFIER ** Retain project required grille width subparagraph below. Delete
subparagraphs not required.
y.
Width: 3/4 inch (19 mm).
z.
Width: 7/8 inch (22 mm).
aa.
Width: 1-1/8 inches (29 mm).
** NOTE TO SPECIFIER ** Delete pattern not required.
bb.
Pattern: As indicated on Drawings.
cc.
Pattern: Colonial.
dd.
Pattern: Prairie A (9 light).
ee.
Pattern: Prairie (6 light).
ff.
Pattern: Specified equal light.
4.
Finelight™ Grilles: Provide contour profile aluminum muntin bars permanently
mounted within insulating glass unit where indicated on Drawings.
a.
Grille Intersections: ABS concealed plastic connectors with nylon end keepers.
** NOTE TO SPECIFIER ** Delete surface finish not required. Specify if exterior color is different
than interior color.
b.
Exterior and Interior Surface Finish: White color painted finish.
3.
08556-30
c.
Exterior and Interior Surface Finish: Sandtone color painted finish.
d.
Exterior and Interior Surface Finish: Terratone color painted finish.
e.
Exterior and Interior Surface Finish: Forest Green color painted finish.
** NOTE TO SPECIFIER ** Below finishes available for Andersen® A-Series Windows only.
f.
Exterior and Interior Surface Finish: Canvas color painted finish.
g.
Exterior and Interior Surface Finish: Dove Gray color painted finish.
h.
Exterior and Interior Surface Finish: Prairie Grass color painted finish.
i.
Exterior and Interior Surface Finish: Red Rock color painted finish.
j.
Exterior and Interior Surface Finish: Cocoa Bean color painted finish.
k.
Exterior and Interior Surface Finish: Dark Bronze color painted finish.
l.
Exterior and Interior Surface Finish: Black color painted finish.
** NOTE TO SPECIFIER ** Delete width not required.
m.
Width: 3/4 inch (19 mm).
n.
Width: 1 inch (25 mm).
** NOTE TO SPECIFIER ** Delete pattern not required.
o.
Pattern: As indicated on Drawings.
p.
Pattern: Colonial.
q.
Pattern: Modified Colonial.
r.
Pattern: Prairie A (9 light).
s.
Pattern: Prairie (6 light).
t.
Pattern: Specified equal light.
u.
Pattern: Short fractional.
v.
Pattern: Tall fractional.
w.
Pattern: Custom.
2.6
DOOR AND WINDOW JOINING SYSTEMS:
** NOTE TO SPECIFIER ** Andersen windows strongly recommends consultation with an
experienced structural engineer, architect, or contractor and a local Andersen representative
when specifying Andersen joining systems. Consult an Andersen representative for joining
options when joining Impact Resistant door products.
** NOTE TO SPECIFIER ** If required for project, retain one of the 1-way or 2-way combinations
below and related subparagraph. Delete combinations not required for project.
A.
LVL Reinforced Joining - 1-way Combination: Provide 4-9/16 inches (116 mm) by 3/4 inch
(19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim
receptor end cap.
1.
Provide corrosion resistant screws and bolts for fastening reinforcement members to
wood frame and fastening end brackets to reinforcement members.
B.
LVL Reinforced Joining - 1-way Combination: Provide 6-9/16 inches (167 mm) by 3/4 inch
(19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim
receptor end caps.
1.
Provide corrosion resistant screws and bolts for fastening reinforcement members to
wood frame and fastening end brackets to reinforcement members.
C.
LVL Reinforced Joining - 2-way Combination: Provide 4-9/16 inches (116 mm) by 3/4 inch
(19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim
receptor end cap.
1.
Provide corrosion resistant screws and bolts for fastening reinforcement members to
wood frame and fastening end brackets to reinforcement members.
D.
LVL Reinforced Joining - 2-way Combination: Provide 6-9/16 inches (167 mm) by 3/4 inch
(19 mm) laminated veneer lumber (LVL) joining with extruded anodized aluminum trim
receptor end caps.
1.
Provide corrosion resistant screws and bolts for fastening reinforcement members to
08556-31
wood frame and fastening end brackets to reinforcement members.
E.
Gusset Plates: Galvanized steel plates as recommended by door manufacturer for specific
application.
F.
Fasteners: Corrosion-resistant screws as provided by door manufacturer for fastening
reinforcement members and gusset plates to wood frame. Other fasteners are provided by
door installer.
G.
Head Flashing: 6 inches (152 mm) long sheet vinyl.
1.
Color: Match door exterior color.
H.
Sealant: As recommended by door manufacturer.
I.
Exterior Vinyl Trim Strips: Provide for each joining method used.
1.
Color: Match door exterior color.
PART 3 EXECUTION
3.1
EXAMINATION
A.
Site Verification of Conditions: Verify that site conditions are acceptable for installation of
units, including the following:
1.
Concrete surfaces are dry and free of excess mortar, rocks, sand, and other
construction debris.
** NOTE TO SPECIFIER ** Retain subparagraph below for masonry construction.
2.
Masonry openings are square and dimensions are correct.
** NOTE TO SPECIFIER ** Retain subparagraph below for wood framing.
3.
Rough openings are square and dimensions are correct.
a.
Sill plates are level.
b.
Wood frame walls are dry, clean, sound, and well nailed or glued, free of voids
and without offsets at joints.
c.
Nail heads are driven flush with surfaces in openings and within 3 inches (75
mm) of rough opening.
3.2
B.
Do not proceed with installation of units until unacceptable conditions are corrected.
C.
If substrate preparation is the responsibility of another installer, notify Architect of
unsatisfactory preparation before proceeding.
PREPARATION
A.
Clean surfaces thoroughly prior to installation.
B.
Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
C.
General:
1.
Remove unit components, parts, accessories, and installation guides from carton.
2.
Inspect unit components and verify that components are not damaged and that parts
are included before disposing of carton.
** NOTE TO SPECIFIER ** Delete if not required.
3.
Field-assemble multiple units before installation in accordance with manufacturer's
installation guide.
D.
Interface With Other Work:
1.
Perform installation in accordance with Manufacturer's instructions.
08556-32
2.
3.
4.
5.
6.
7.
8.
Install units level, plumb, square, true to line, without distortion, anchored securely in
place to structural support, and in proper relation to wall flashing and other adjacent
construction.
Separate aluminum and other corrodible surfaces from sources of corrosion or
electrolytic action at points of contact with other materials.
Install insulation in shim space around unit perimeter to maintain continuity of building
insulation. Do not overfill.
Hold back exterior siding or other finish materials from edge of unit to allow for
expansion and contraction and installation of proper joint sealant with backing
materials. Seal perimeter of unit after exterior finish is applied per requirements of
Division 07 "Joint Sealants" Section.
Extend vapor barrier to interior face of unit frame and attach.
Finish interior units per requirements specified in related sections. Refer to, and
comply with, additional requirements in manufacturer's installation guides.
Install optional hardware and unit accessories after cleaning.
E.
Site Tolerances:
1.
Adjust operation, insect screens, hardware, and accessories for a tight fit at contact
points and weatherstripping for smooth operation and weather tight closure.
** NOTE TO SPECIFIER ** Specify the final action required to clean installed equipment or other
completed work to properly function or perform. Coordinate article below with Division 01
Execution Requirements (Cleaning) Section and specific project requirements.
3.3
CLEANING
A.
Clean units using cleaning material and methods specifically recommended by window
manufacturer.
B.
Remove excess sealants, glazing materials, dirt, and other substances.
C.
Avoid damaging protective coatings and finishes.
D.
Protect unit surfaces from masonry cleaning solution that could damage insulation glass
panels or hardware.
E.
Remove debris from work site and properly dispose of debris.
** NOTE TO SPECIFIER ** Delete if not required.
3.4
FIELD TESTING
** NOTE TO SPECIFIER ** Coordinate article below with conditions of the contract and with
division 01 quality control. Testing equipment shall be calibrated per Section 9 of ASTM E1105:
Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows,
Skylights, Doors and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference, where the
water test pressure shall be run at 2/3 (0.667) of the water test pressure used to achieve the
products rated design pressure. The numbers of products tested shall be agreed and written in
the project specification and shall not exceed 1 percent of the total number of openings unless
specified otherwise.
A.
General: Test units per the following procedures:
1.
Inspect units and verify installation per Manufacturer's instructions.
2.
For products installed less than 6 months, comply with AAMA 502-08 Voluntary
Specification for Field Testing of Windows and Sliding Glass Doors, Procedure B.
3.
For products installed longer than 6 months, comply with AAMA 511-08: Voluntary
Guideline for Forensic Water Penetration Testing of Fenestration Products. If test
indicates that field testing of units is necessary, test product as indicated in paragraph
1 above.
08556-33
4.
3.5
Do not proceed with installation of additional units until unacceptable conditions are
corrected.
PROTECTION
A.
Protect installed products until completion of project.
B.
Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION
08556-34