FDOT Matrix Derived from Specification A650 Effective 04/05/2012

advertisement
FDOT Matrix Derived from Specification A650 Effective 04/05/2012 Rev 3.0
FDOT Traffic Engineering Research Laboratory (TERL)
Signal Module Compliance Matrix
Date:
ID
No
1
Click here to enter a date.
Manufacturer:
Applicant’s
Name (print):
Item, Model No.:
Signature:
Item
Comply?
(Yes/No)
By signing this form, the applicant declares that he/she has read and
understands the provisions of Section A650 of the FDOT Minimum
Specifications for Traffic Control Signals and Devices, and all implemented
modifications. The requirements listed on this matrix are derived from Section
A650, and are the basis for determining a product’s compliance and its
acceptability for use on Florida’s roads.
Comments
(Applicant must provide information as indicated)
Provide a third party test report that demonstrates
compliance with this requirement. The test report must
meet the requirements of FDOT Product Certification
Handbook (PCH), section 7.2.
Indicate location of requested information in submittal.
TERL Evaluation
Method
Document Review
LED Signal Module is compatible with currently approved traffic
signal housings.
Manufacturer's name, model number, date of manufacture, and
serial number are permanently marked on the rear of the LED
signal module.
LED signal module will be marked with a permanent label that
includes the FDOT Certification Number once the device has
been approved.
Lens is tinted with an appropriate color (red, amber or green) to
reduce sun phantom affect and enhance on/off contrast.
Tinting is uniform across the face of the lens, free from streaks,
wrinkles, chips, bubbles, or other imperfections.
If lens is polymer, a surface coating is incorporated to provide
abrasion resistance.
Applicant may provide comments in this field.
Physical Inspection
Applicant may provide comments in this field.
Physical Inspection
Provide a statement of conformance in this field.
Compliance Matrix
Review
Applicant may provide comments in this field.
Physical Inspection
Applicant may provide comments in this field.
Physical Inspection
Provide a statement of conformance in this field.
Compliance Matrix
Review
Electrical conductors for LED signal modules are a minimum of
36 inches in length.
Provide a statement of conformance in this field.
9
Each lead from the LED module is terminated with insulated
slide-on terminals.
Provide a statement of conformance in this field.
10
Conductors are color coded as follows:
Provide a statement of conformance in this field.
Compliance Matrix
Review and
Physical Inspection
Compliance Matrix
Review and Physical
Inspection
Compliance Matrix
Review and Physical
Inspection
2
Section
A650-3
Requirement
Except as indicated in the following criteria, LED Optical Unit
conforms to the requirements of the latest LED Purchase
Specification of the Institute of Transportation Engineers (ITE),
“Vehicle Traffic Control Signal Heads - Light Emitting Diode
(LED) Circular Signal Supplement”.
A650-3.1
3
4
5
A650-3.2
6
7
8
A650-3.3
White identifies the neutral lead;
Red circular signals are identified with a red lead;
Yellow circular signals are identified with a yellow lead;
Green circular signals are identified with a green lead;
Red arrows are identified with a red and black tracer lead;
Yellow arrows are identified with a yellow and black tracer lead;
Green arrows are identified with a green and black tracer lead.
11
A650-3.4
Red and green modules meet the current requirements of ITE’s
Performance Specification, Vehicle Traffic Control Signal Heads
– Light Emitting Diode (LED) Circular Signal Supplement. Yellow
Provide a third party test report that demonstrates
compliance with this requirement. The test report must
meet the requirements of FDOT PCH, section 7.2.
Page 1 of 2
Document Review
FDOT Matrix Derived from Specification A650 Effective 04/05/2012 Rev 3.0
ID
No
Section
Requirement
modules are 1.7 times brighter than the aforementioned ITE
specification.
Item
Comply?
(Yes/No)
Page 2 of 2
Comments
(Applicant must provide information as indicated)
Indicate location of requested information in submittal.
TERL Evaluation
Method
Download