Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 1
This section addresses Pittco 70 Wall XT Curtain Wall System, and includes an aluminum frame
assembly and double or triple pane sealed insulating unit glazed lites, for exterior applications, shop
fabricated, factory pre-finished, including field glazing. The system application is intended for
multiple story installations. Glass and Glazing is referenced to Section 088000. Sealants are
referenced to Section 079200. Door hardware may be specified in this section or specified in Section
087100; edit text accordingly. Operable sash, if any, is usually specified in Aluminum Windows,
Section 085100. Exterior sunshades are specified in Exterior Sun Control Devices 107113. Where
work of this section integrates with another glazing assembly, carefully coordinate both sections to
function together. Air barrier and vapor retarder continuity from this system to adjacent construction
is critical to successful building air and moisture tightness; specify compatible materials in
conjunction with Sections 072500, 072600, and 072700. This section includes performance,
proprietary and descriptive type specifications. Edit to avoid conflicting requirements.
During editing, delete all blue text boxes such as this text box. Also, select one of the options shown in
blue for each section and delete the remaining options. Change the text color to black for the selected
option.
PART 1 - GENERAL
1.1
SECTION INCLUDES
A. Glazed aluminum framed [2 1/2” x 6”], [2 1/2” x 7”], [2 1/2” x 8”], [2 1/2” x 11”] stick or ladder built
[exterior glaze], [exterior and interior glaze] pressure plate curtainwall assembly.
B.
Monolithic glass, Double, or triple pane insulating glass.
Include the following paragraph if door hardware is specified in Part 2 of this section; delete the
following paragraph if hardware is referenced in Section 087100 – Door Hardware.
C.
Furnish [Pittco Standard Door Hardware] [Custom Door Hardware indicated in Part 2] [Door Hardware
referenced in Section 087100].
D. Perimeter sealant referenced in section 079000.
E.
1.2
RELATED SECTIONS
Select and edit the paragraphs in this article – delete those that do not apply to the project.
A. Section [_______]: Preparation of adjacent work to receive work of this section.
B.
Section 055000 – Metal Fabrications: Steel fabricated [attachment devices] [framed openings].
C.
Section 072500 – Weather barriers
D. Section 072600 – Vapor Retarders: Vapor seal at adjacent construction.
E.
Section 072700 – Air Barriers: Air seal at adjacent construction.
F.
Section 079200 – Joint Sealers: Assembly perimeter sealant and back-up materials.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 2
G. Section 084113 – Standard Aluminum Entrances: Door and frame assembly to fit within this glazed
assembly.
H. Section 084113 – Monumental Aluminum Entrances: Door and frame assembly to fit within this glazed
assembly.
I.
Section 085100 – Aluminum Windows: Operable sash within framing members of this section.
J.
Section 087100 – Door Hardware: Mortised hardware reinforcement requirements affecting framing
members.
K.
Section 087113 – Automatic Door Equipment.
L.
Section 088000 – Glass and Glazing.
M. Section 107113 – Sun Control Devices
N. Section [_______]: Wall fin convectors and support saddles attached to the framing members.
O.
1.3
REFERENCES
List reference standards included within the text of this section. Edit the following as required for
project conditions. Standards with an “M” after the designation are metric versions or remove all
and reference index for applicable standards.
A. AA (Aluminum Association), Designation System for Aluminum Finishes.
B.
AAMA MCWM-1-89, Metal Curtain Wall Manual.
C.
AAMA CWG-1-89, Installation of Aluminum Curtain Walls.
D. AAMA 501.1-05, Standard Test Method for Water Penetration of Windows, Curtain Walls and doors
using Dynamic Pressure.
E.
AAMA 501.2-09, Quality Assurance and Diagnostic Water Leakage Field Check of Installed Storefronts,
Curtain Walls, and Sloped Glazing Systems.
F.
AAMA 503-08, Voluntary Specification for Field Testing of Newly Installed Metal Storefronts, Curtain
Walls, and Sloped Glazing Systems.
G. AAMA 609/610-09, Cleaning and Maintenance Guide for Architecturally Finished Aluminum.
H. AAMA 611-12, Voluntary Specifications for Anodized Architectural Aluminum.
I.
AAMA 1503-09, Voluntary Test Method for Thermal Transmittance and Condensation Resistance of
Windows, Doors, and Glazed Wall Sections.
J.
AAMA 2604-10, Voluntary Specification, Performance Requirements and Test Procedures for High
Performance Organic Coatings on Aluminum Extrusions and Panels.
K.
AAMA 2605-11, Voluntary Specification, Performance Requirements and Test Procedures for Superior
Performing Organic Coatings on Aluminum Extrusions and Panels.
L.
ASTM A 123/A 123M, Zinc (Hot Dip Galvanized) Coatings on Iron and Steel Products.
M. ASTM A 653/A 653M, Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated
(Galvanized) by the Hot-Dip Process.
N. ASTM B 209/B 209M, Aluminum and Aluminum-Alloy Sheet and Plate.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 3
O. ASTM B 221/B 221M, Aluminum and Aluminum-Alloy Extruded Bar, Rod, Wire, Shape and Tube.
P.
ASTM E 283, Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors.
Q. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Skylights, Curtain Walls, and
Doors by Uniform Static Air Pressure Difference.
R.
ASTM E 331, Test Method for Water Penetration of Exterior Windows, Skylights, Curtain Walls, and
Doors by Uniform Static Air Pressure Difference.
S.
1.4
SYSTEM DESCRIPTION
Use this article carefully; restrict statements to describe components used to assemble the system. Do
not repeat statements made if the Section includes article in Part 1, Section 1.1.
A. Aluminum curtain wall assembly consists of tubular aluminum framing sections with deep polyamide
isobar for thermal separation and glazed with screw applied exterior retainers covered with finished
faces . System is shop fabricated with internal reinforcing as needed, anchorage, attachment devices,
and related flashings.
Fabrication and erection of the glazed frame assembly is usually left to the prerogative of the
assembly fabricator. If site conditions, opening tolerances or quality of the work may be an issue or a
concern, it may be prudent to require either shop assembly or field erection of the frame assembly.
Select one of the following options as appropriate.
B. Frame Assembly: [Stick built or site assembled.] [Shop assembled in ladder frames.]
C.
1.5
PERFORMANCE REQUIREMENTS
Use this article carefully; restrict statements to identify system performance requirements or
functional criteria only. Delete paragraphs not appropriate to project. Performance specifying
permits system manufacturers the latitude to adjust proprietary systems to achieve specified
requirements. Rely on this article as the basis for assembly criteria specifying and minimize the
material and component statements so not to conflict with performance criteria. If more stringent
criteria are being considered, refer to AAMA and ASTM test methods and associated documents for
guidance or consult with Pittco representative.
A. Assembly Design: Design and size components to withstand dead and live loads caused by positive and
negative wind pressure acting normal to the plane of the wall as calculated in accordance with the
applicable code.
B.
Assembly: Accommodate without damage to components or deterioration of seals, movement
between system and supporting structure including live load deflection, story drift and twist, long term
creep, and column shortening.
For mullion, corner, and special change of wall plane conditions, limit glazing sealant design
movement to 20 percent maximum for elastomeric sealants or 5 percent maximum for acrylic or butyl
sealants. Special conditions may require special statements in the paragraph below; edit accordingly.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
C.
084413
Glazed Aluminum Curtain Wall
Page 4
Structural Performance – Deflection: Limit mullion deflection to [flexural limit of glass,] [L/175] [_____]
[L/175 for spans less than 13’-6” and L/240 + 1/4” for spans greater than 13’-6”] as measured in
accordance with ASTM E 330 at [_____] psf ([_____] Pa); with full recovery of members.
D. Air Infiltration: Limit air leakage through the assembly to [0.06] [_____] cfm/ft2 ([1.5] [_____] L/m2•s)
of wall area, measured at a reference differential pressure across the assembly of [6.24] [_____] psf (
[300] [_____] Pa) as measured in accordance with ASTM E 283.
E.
Static Water Leakage: None, as measured in accordance with ASTM E 331 with a test pressure
difference of [15] [_____] psf ([720] [_____] Pa).
F.
Dynamic Water Leakage: None, as measured in accordance with AAMA 501.1 with a test pressure
difference of [15], [_____] psf ([720] [_____] Pa).
G. Condensation Resistance Factor (CRF): [58 with clear, 1” IGU], [67 with low E, 1” IGU], [74 with low E
and argon, 1” IGU] [_____], [71 with low E, 1 1/2” triple glaze IGU], [82 with Low E and argon, 1 1/2”
triple glaze IGU] when measured in accordance with AAMA 1503.
H. Thermal Transmittance (U Factor): [0.52 with clear, 1” IGU], [0.37 with low E, 1” IGU],[0.30 with low E
and argon, 1” IGU], [0.32 with Low E, 1 1/2” triple glaze IGU], [0.22 with low E and argon, 1 1/2” triple
glaze IGU], [_____] BTU/hr• ft2•degree F when measured in accordance with AAMA 1503.
I.
Air and Vapor Seal: Maintain continuous air barrier and vapor seal throughout assembly, primarily in
line with lite of glass.
J.
Expansion/Contraction: Provide for expansion and contraction within assembly components caused by
ambient cycling temperature range of [180] [_____] degrees F ([82] [_____] degrees C) over a twelve
(12) hour period based on a metal installation temperature of 85 degrees F (29 degrees C), without
causing detrimental effect to assembly components and anchorage.
K.
System Internal Drainage: Drain water entering joints, condensation occurring in glazing channels, or
migrating moisture occurring within system, to the exterior by a [top to bottom], [zone dam] weep
drainage network.
L. Thermal Performance: Glazed aluminum curtain wall tested in accordance with NFRC and AAMA
standards.
M. Seismic – When tested to AAMA 501.4 allow movement to 1 1/2”.
N.
1.6
SUBMITTALS FOR REVIEW
Do not request submittals if drawings sufficiently describe the products of this section or if
proprietary specifying techniques are used. The review of submittals increases the possibility of
unintended variations to drawings, thereby increasing the Specifier’s liability. The following
submittals are intended for review and approval or other action by the Specifying Authority.
A. Section [013000:] [_______:] Submission Procedures.
B. Product Data: Provide component dimensions; describe components within assembly, anchorage and
fasteners, glass, [door hardware,] internal drainage details and [_______].
C. Design Data: Provide framing member structural and physical characteristics, [calculations,]
dimensional limitations.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 5
D. Shop Drawings: Indicate system dimensions, framed opening requirements and tolerances, affected
related work and expansion and contraction joint location and details.
Use the following paragraph(s) for submission of physical samples for selection of finish, color,
texture, etc.
E.
Submit [two] [_____] samples [1-3/4 x 4 inch] [_____ x _____] inch [45 x 100 mm] [_____ x _____] mm
in size illustrating finished aluminum surface.
F.
Submit [two] [_____] samples [12 x 12 inch] [_____ x _____] inch [305 x 305 mm] [_____ x _____] mm
in size illustrating glass infill, glazing materials.
G.
1.7
SUBMITTALS FOR INFORMATION
The following submittals are informational; responsive action by the Specifying Authority is not
required.
A. Section [013300:] [_______:] Submission procedures.
B.
Manufacturer’s Certificate: Certify that [Products] [_____] meet or exceed [specified requirements.]
[_______.]
C.
1.8
SUBMITTALS FOR PROJECT CLOSEOUT
The following submittals are for project close-out purposes.
A. Section [017800:] [_______:] Submission Procedures.
B.
Submit manufacturer warranty and ensure forms have been completed in Owner’s name and registered
with manufacturer.
C.
1.9
QUALITY ASSURANCE
Only include this article if the specified system is extensive and warrants special design attention.
subsequent paragraph is to address requirements for the handicapped.
The
A. Design and fabricate according to AAMA MCWM-1.
B.
Perform work according to AAMA CWG-1.
C.
Manufacturer [and Installer]: Company specializing in manufacturing aluminum glazing systems with
minimum [three] [_____] years [documented] experience.
D. Design structural support framing components under direct supervision of a Professional Structural
Engineer experienced in design of this work and licensed at the place where the Project is located.
E.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
1.10 PRE-INSTALLATION MEETING
084413
Glazed Aluminum Curtain Wall
Page 6
A. Section [013100:] [_______:] Pre-installation meeting.
B.
Convene [one] [_____] week before starting work on this section.
C.
1.11 DELIVERY, STORAGE, AND PROTECTION
A. Section [016600:] [_______:] Transport, handle, store, and protect products.
Only include the following paragraph if the specified system is extensive and warrants special
handling.
B.
Handle products of this section in accordance with AAMA – Curtain Wall Manual #10.
C.
Protect finished aluminum surfaces with [wrapping] [removable protective material]. Do not use
adhesive papers or sprayed coatings which bond when exposed to sunlight or weather.
D.
1.12 PROJECT CONDITIONS
A. Section [013100:] [_______:] Coordination and meetings.
In the following paragraph, only include the firestopping, air barrier, and vapor retarder barrier
option statements if that work is specified in other sections.
B.
Coordinate the work with installation of [firestopping,] [air barrier,] [vapor retarder,] [and] [_______]
components or materials.
C.
1.13 ENVIRONMENTAL REQUIREMENTS
A. Section [013500:] [_______:] Environmental conditions affecting products on site.
If dry glazing methods are utilized, delete this article.
B. Do not install sealants when ambient temperature is less than [40] [_____] degrees F ([5] [_____]
degrees C) during and [48] [_____] hours after installation.
C.
1.14 WARRANTY
Improper specifying of warranty and correction period extensions may limit the statutory rights of the
owner and the ability to enforce claims under the contractor’s contractual warranty. Consult legal
counsel before editing this article.
A. Section [017800:] [_______:] Warranties.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 7
The following paragraph extends the correction period beyond one year. An extended correction
period adds to the construction cost and may not be enforceable.
B.
Correct defective work within a [one (1)] [five (5)] year period after substantial completion.
C.
Warranty: Include coverage for complete system for failure to meet specified requirements.
The following paragraph requests a manufacturer warranty; the request may not be effective as the
manufacturer is outside the jurisdiction of the Owner/Contractor contract. Coordinate this
paragraph with the Submittals at Project Closeout article. Manufacturer’s warranty for glass is
described in Section 088000.
D. Provide [five (5)] [_____] year manufacturer warranty for glazed units.
E.
PART 2 - PRODUCTS
2.1
MANUFACTURERS
The following manufacturer and their product should be used for the creation of drawing details and
door schedules. Specify the following paragraph alone or add the second paragraph indicating other
manufacturers who are also permitted to bid, providing their product conforms to or exceeds these
specification requirements.
A. Base Product: Pittco Architectural Metals, Inc., ________ - ________. Phone 800-992-7488, Fax 847593-9946, Internet web site at http://www.pittcometals.com.
Edit the following paragraphs and other descriptive specification requirements elsewhere in this
section to eliminate any conflict with the following “other” manufacturer’s products.
B.
Other acceptable manufacturers conforming to specified requirements:
C.
1.
[______________________________].
2.
[______________________________].
Substitutions: Not permitted.
D.
2.2
MATERIALS
A.
B.
C.
D.
E.
Extruded Aluminum: [ASTM B 221,] [ASTM B 221M,] 6063 alloy of [T5] [T6] temper.
Sheet Aluminum: [ASTM B 209.] [ASTM B 209M.] [_______.]
Sheet Steel: [ASTM A 653/ASTM A 653M] [_______]; galvanized in accordance with [_______].
Fasteners: [Stainless] [non-magnetic stainless in exposed areas, or other non-corrosive materials
compatible with framing] steel.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
2.3 COMPONENTS
084413
Glazed Aluminum Curtain Wall
Page 8
The following paragraph identifies the nominal dimensions of the primary framing members. If
performance specifying, ensure no conflict exists.
A. Frame:
1.
Exposed to view Nominal Width: 2 1/2 inch (64 mm).
2.
Nominal Depth with 1” IGU: [6 inch (152 mm)] [7 inch (178 mm)] [8 inch (203 mm)] [11 inch (279
mm)].
3.
Nominal Depth with 1 1/2” IGU: [6 1/2 inch (165 mm)] [7 1/2 inch (191 mm)] [8 1/2 inch (216 mm)]
[11 1/2 inch (292 mm)].
4.
Nominal Depth with 1 3/4” IGU: [6 3/4 inch (171 mm)] [7 3/4 inch (196 mm)] [8 3/4 inch (221 mm)]
[11 3/4 inch (298 mm)].
5.
Frame Assembly with deep thermally isolated design.
6.
Dedicated perimeter mullion.
7.
Mounting and attachments from the intermediate mullion, head, or sill.
8.
Flush, pressure plate type glazing stops.
9.
Drainage: [Concealed internal weep drainage from top to bottom], [zone dam with weep holes in
face and retainers] .
B.
Reinforced Mullion: Extruded aluminum section with internal reinforcement of steel tube section, steel
bar section, or extruded aluminum section.
C.
Doors: Specified in Section [084113] [
].
D. Door Hardware: Specified in Section [087100.] [_______.]
E.
Flashings: 0.040 inch (1 mm) thick [aluminum] [galvanized steel,] [_______,] finish [as selected.] [to
match mullion sections where exposed.]
F.
Operable Sash: Specified in Section [085100] [_______], hopper or awning operation.
G. Vapor Retarder: [Specified in Section [072600] [_______].] [Sheet EPDM.] [_______.]
H. Air Barrier: [Specified in Section [072700] [_______].] [Sheet steel, galvanized.] [_______.]
I.
2.4
GLASS AND GLAZING MATERIALS
Incorporate glass or plastic glazing materials by direct reference to Section 088000. The following
paragraphs only describe glass or plastic types; coordinate with a schedule in Section 088000.
A. Glass: Specified in Section 088000, of type described below:
1.
Outer Lite: [Float] [Heat-Strengthened] [_______], [Clear.] [_______.]
2.
Space: [Dry Air.] [Argon Gas.]
3.
Inner Lite: [Float] [Heat-Strengthened] [_______], [Clear.] [Low-E Coating on #3 Surface.]
[_______.]
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
B.
084413
Glazed Aluminum Curtain Wall
Page 9
4.
Nominal Unit Thickness: [1 inch (25 mm)], [1 1/2 inch (38 mm)], [1 3/4 inch (44 mm), [_____] inch (
[_____] mm).
5.
U-Factor: [_____] BTU/hr•ft2•degree F
Glazing Materials: [Exterior glaze dense EPDM at exterior and sponge EPDM at interior], [Interior glaze
dense EPDM at exterior and dense EPDM wedge at interior], to suit applications and achieve weather,
moisture and air infiltration requirements.
C.
2.5
SEALANT MATERIALS
Incorporate sealant materials by direct reference to Section 079200. The following paragraphs only
describe sealant type; coordinate with schedule in Section 079200. Sealants used for glazing are
specified in Section 08800
0
0.
A. Sealant and Backing Materials:
1.
Perimeter Sealant: [_______] type as specified in Section [079200.] [_______.]
2.
Sealant Used Within System (Not Used With Glazing): [_______] type specified in Section [079200.]
[_______.]
B.
2.6
FABRICATION
A.
Fabricate components with minimum clearances and shim spacing around perimeter of
assembly, yet enabling installation and dynamic movement of perimeter seal.
B.
Accurately fit and secure joints and corners. Make joints flush, hairline, and weatherproof.
C.
Prepare components to receive anchor devices. Fabricate anchors.
D.
Arrange fasteners and attachments to conceal from view.
The following paragraph would only apply if blinds or draperies are intended at the interior side of
the glazed wall assembly, and the dead weight and operating loads of such items warrant attachment
reinforcement in this section.
2.7
E.
Reinforce interior horizontal head rail to receive [drapery] [blind] track brackets and
attachments.
F.
Prepare components with internal reinforcement for door hardware [and door operator hinge
hardware].
G.
Reinforce framing members for imposed loads.
FINISHES
The wide variety of finishes for aluminum preclude listing all of the available options; the following
paragraphs offer the commonly specified finishes, either by reference to AAMA finishes or by generic
or proprietary description. Specify the anodizing color whenever possible, as the color varies
considerably between finishes. The AAMA A41 and A44 class finishes are anodized 0.7mils (0018
mm) thick or greater (termed Architectural Class I); A41 is clear and A44 is anodized in two steps.
The A31 series is thinner and will vary between 0.4 mils (0.010 mm) and 0.7 mils (0.018 mm) (termed
Architectural Class II Clear).
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 10
A. Exposed Aluminum Surfaces: AA M10 caustic etch C21 A31, anodized to Class II Clear Color.
[OR]
B.
Exposed Aluminum Surfaces: AA M10 C21 [A41 or A44], anodized to Class I [_______] color.
[OR]
C.
Anodized Coating: [[Standard finish] [#62 Dark Bronze] [#63 Black]] [[Special order finish are available
but may require longer lead times] [#60 Light Bronze] [#61 Medium Bronze][#59 Champagne]].
[OR]
D. Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA
Specification 2604, High Performance Organic Coatings on Aluminum.
E.
Type: Factory Applied, High Performance, 50% Polyvinylidene Fluoride (PVDF) Coating formulated by a
licensed paint manufacturer, and applied by Paint Manufacturer’s Warranty-Approved Applicator.
F.
Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic
surface soils, remove residual oxides, followed by a Chrome Phosphate or Chromate Coating to ensure
adhesion to the aluminum.
G. Color: {Specifier to insert color code here, e.g., UC 40577 (Duranar Black)}.
[OR]
H. Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA
Specification 2605, Superior Performing Organic Coatings on Aluminum.
I.
Type: Factory Applied, High Performance, 70% Polyvinylidene Fluoride (PVDF) Coating formulated by a
licensed paint manufacturer, and applied by Paint Manufacturer’s Warranty-Approved Applicator.
J.
Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic
surface soils, remove residual oxides, followed by a Chrome Phosphate or Chromate Coating to ensure
adhesion to the aluminum.
K.
Color: {Specifier to insert color code here, e.g., UC 40577 (Duranar Black)}.
L.
Apply [one coat] [[____] coats] of bituminous paint to concealed aluminum [and steel] surfaces in
contact with cementitious or dissimilar materials.
M. Concealed Steel Items: [Stainless Steel.] [Galvanized Steel to ASTM A 123/A 123M] to [2.0] [_____]
oz/ft ([610 [_____] g/m).] [Primed with manufacturer’s shop coat primer.]
N. Extent of Finish:
1.
Apply factory coating to all surfaces exposed at complete assemblies.
2.
Apply touch-up materials for field application to minor damage of factory applied finish.
Include the following paragraph if interior and exterior colors differ.
O. Schedule of Differing Finish Colors:
1.
Exterior Surfaces: [________] color.
2.
Interior Surfaces: [________] color.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 11
P.
PART 3 - EXECUTION
3.1
EXAMINATION
A. Section [017000:] [_______:] Verification of existing conditions before starting work.
B.
Verify dimensions, tolerances, and method of attachment with other work.
C.
Verify wall openings and adjoining air and vapor seal materials are ready to receive work of this section.
D.
3.2
INSTALLATION
A. Install wall assembly in accordance with manufacturer’s instructions.
B.
Attach to structure to permit sufficient adjustment to accommodate construction tolerances and other
irregularities.
C.
Provide alignment attachments and shims to permanently fasten system to building structure.
D. Align assembly plumb and level, free of warp or twist. Maintain assembly dimensional tolerances,
aligning with adjacent work.
E.
Provide thermal isolation where components penetrate or disrupt building insulation.
F.
Install [sill] flashings. Turn up ends and edges; seal to adjacent work to form water tight end dam.
G. Coordinate attachment and seal of perimeter air and vapor barrier materials.
H. Pack fibrous insulation in shim spaces at perimeter of assembly to maintain continuity of thermal
barrier.
I.
Install operating sash to sash manufacturer’s installation requirements.
J.
Install flashings, full opening width, consisting of one piece. If width of opening requires additional
pieces, splice per manufacturer’s instructions.
K.
Set thresholds in bed of mastic and secure.
L.
Install hardware using physical hardware and templates provided. [Refer to Section 087100 for
installation requirements.]
M. Install glass in accordance with Section 088000, utilizing glazing method required to achieve
performance criteria.
The following paragraph indicates installation of perimeter sealant materials as part of this section
and references Section 079200 for materials and application.
N. Install Perimeter Sealant:
1.
Utilizing method required to achieve performance criteria.
2.
Use [silicone] [urethane] [______] sealant, required backing materials, and recommended
installation procedures.
3.
According to the requirements of Section 079200.
O. Install [Sunshades] according to manufacturer’s installation requirements.
Pittco Architectural Metals, Inc.
Pittco 70 Wall XT
2014
084413
Glazed Aluminum Curtain Wall
Page 12
P.
3.3
ERECTION TOLERANCES
A. Section [014000:] [_______:] Tolerances.
B.
Maximum Variation from Plumb: 1/16 inch every 3 feet (1.5 mm/m) non-cumulative or 1/16 inch per
10 feet (1.5 mm/3 m), whichever is less
C.
Maximum Misalignment of Two Adjoining Members Abutting in Plane: 1/32 inch (0.8 mm).
D.
3.4
FIELD QUALITY CONTROL
Only include this article if special field inspection services will be involved.
A. Section [014000:] [_______:] Field [inspection,] [testing,] [adjusting,] [and] [balancing].
B.
Inspection will monitor quality of installation and glazing.
C.
3.5
ADJUSTING
A. Section [017000:] [_______:] Adjusting installed work.
B.
Adjust operating hardware [and sash] for smooth operation.
C.
3.6
CLEANING
A. Section [017400:] [_______:] Cleaning installed work.
B.
Remove protective material from pre-finished aluminum surfaces.
C.
Wash down surfaces with a solution of mild detergent in warm water, applied with soft, clean wiping
cloths. Take care to remove dirt from corners. Wipe surfaces clean.
D. Remove excess sealant employing a method acceptable to sealant manufacturer and finish supplier.
E.
3.7
PROTECTION OF FINISHED WORK
A. Section [017600:] [_______:] Protecting installed work.
B.
Protect finished work from damage.
C.
END OF SECTION