Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
Lec-6
Specialty polymers and Their blends
The specialty resins are expensive, produced in relatively small
volumes either for a specific application or looking for a market niche.
Their Tg > 200°C and modulus > 3 GPa.
In 1991 the total world consumption of polysulfones (PSF) and
polyethersulfones (PES) was 8.5 kton.
Blends of the following polymers are known: polyfl uorocarbons,
polysiloxanes, sulfur-containing polymers (PPS, PPSS, PES, and PSF),
polyetherketones (PEK, PEEK, PEKK), polyimides (PI, PEI, and PAI),
PAr, COPO, polyphosphazene (PHZ) and LCP.
1- Fluorocarbon Polymers:
A- Polytetrafluoroethylene (PTFE): (Teflon)
Known in Germany since 1933.It is a semicrystalline resin (92-98%
crystallinity), with Tm = 342°C and melt viscosity of η = 10 GPas.
B-Polychlorotrifluoroethylene (PCTFE), Hostaflon™ commercialized in
1934
C- Fluorinated ethylene-propylene (FEP), Teflon™-FEP introduced
in 1972
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
4- Numerous copolymers with Tm = 260 to 304°C, processable at
Tprocess = 315 to 425°C, and having the degradation temperature,
Tdeg = 425 to 440°C.
The fluoropolymers are characterized by :
1- Stability at high Ts 2- Toughness and flexibility at low Ts
3- Low friction
4- Insolubility and inertness to chemicals
5-Low dielectric losses and high dielectric strength.
The world consumption of fluoropolymers in 1991 was 72 kton.
In blends, fluoropolymers are used in small quantities to:
1- Enhance throughput
2- Reduce the frictional properties( improved anti-friction properties)
3- Increase the wear resistance.
4- PPS and PEEK blended with a fluoro(co)- polymers and reinforced
with either CF or GF were wear resistant with a short break-in
period for forming a self lubricating film.
2- Siloxane Polymers:
Polysiloxanes, [-O-Si(RR’)-], are linear resins that can be branched or
crosslinked into elastomers.
They have high compressibility, permeability to
gases, low Tg and viscosity, exceptional weatherability,
low surface tension coeffi cient and are
relatively expensive.
Siloxane polymers or copolymers have been incorporated into
engineering or specialty resins to improve:
1- Processability
2-Toughness
3- HDT
4- Solvent resistance
5-Weather resistance.
Main polymers of this type are:
Polydimethylsiloxane (PDMS), and polymethylphenylsiloxane (PMPhS).
Their Tg = -127 and -86°C, respectively. They start oxidizing at 290 and
375°C and undergo structural rearrangement at 435 and 410°C.
Polysiloxanes have been used as high temperature impact modifiers that
improve: 1- Flame resistance
2- Processability
3- Optical
properties
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
Several commercial blends are on the market:
1- Rimplast™ : (high tensile, flexural, & Izod impact strength
PA’s)
2- Dialoy™ :(PC/PET blends with good chemical, weather, and low-T
impact resistance).
3- Polyarylene Sulfide (PPS):
Polyarylenesulfides (PPS), (-φ-S-)n, was commercialized in 1971 as
Rayton™ R. The resin is semicrystalline with Tg = 194°C and Tm =
288°C, thus Tprocess ≥ 290°C.
PPS is difficult to mold —it tends to adhere to the mold surface and to
flow into mold crevices. It has also relatively poor impact resistance.
Blends have been developed to alleviate these problems, e.g., with 25
wt% of either PSF, PPE, or PC.
Commercial PPS blends are available with PPE (e.g., DIC PPS
commercialized in 1982, Noryl™ APS), PARA (RTP 1300), or PTFE
(Lubricomp™ PPS). They show good processability with reduced fl ash,
are tough, have excellent wear, as well as high heat, solvent, chemical,
and oxidation resistance.
The PPS/PSF blends have been developed to improve PPS processability
and/or the mechanical performance over a wide range of temperatures, to
improve PSF weatherability.
PAr’s are aromatic amorphous polyesters. Their Tg = 188°C and HDT =
120-175°C. Blends with PPS have been developed to improve the
performance of PAr — processability, rigidity and hydrolytic stability.
To improve processability, the main-chain flexibility was enhanced by
incorporating segments with higher mobility, viz. polyamide-imide (PAI),
polyetherimide (PEI), polyimide-sulfone (PISO), etc. These polymers are
characterized by high Tg = 150-420°C and thermal resistance.
They are blended with PPS to enhance its moldability, thermal stability
and mechanical performance.
Oxidation of PPS by addition of N2O4 in a sulfuric acid solution, results
in the incorporation of surfoxide groups, leading to either
polyphenylenesulfidesulfoxide or polyphenylenesulfoxide.
Their blends with high temperature resins produced high temperature
resistant foams . The process reduced the moldings’ density by at least
50%.
4- Polysulfone (PSF):
Polyarylsulfones (PSF or PSU), or polyarylethersulfones (PAES) have
the chain structure: (-φ-SO2 -)n.
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
PSF’s are transparent, flame resistant, have high strength, modulus and
hardness, HDT > 200°C. They show excellent resistance to thermal and
irradiation degradation, but are difficult to process (high melt viscosity),
have low ESCR(Environmental stress cracking resistance) and poor
weatherability.
The latter properties can be improved by blending and/or reinforcing.
Many PSF blends of with engineering resins have been developed, viz.
with PA, PEST, PC, PPE, or POM. They have high HDT, heat resistance,
strength, stiffness, mechanical properties and ESCR.
5- Polyetheretherketone (PEEK) :
Polyaryletherketones (PAEK) are aromatic polymers with ether and
ketone linkages in the chain, viz. PEK, PEEK, PEEKK, etc.
Polyetheretherketone (Victrex™ PEEK),
was commercialized in 1980 (Tg = 143°C, Tm = 334°C).
Commercial blends of PEEK include, Sumiploy™ PEEK/PES/PTFE,
PEEK/LCP, Cortem™ PEEK/LTG, etc.
6- Polyimides (PI, PEI or PAI):
Polyimides (PI) have imide group, -R-N=(CO)2=R’-, in the main chain.
Owing to a variety of possible R and R’ groups, their Tg = 180-420°C.
To improve processability, flexible groups were incorporated into the
main chain.
Polyamideimides (PAI) have high tensile and impact strength from T =
-190 to T = 260°C, dimensional stability, good dielectric properties,
solvent and chemical resistance, flame retardancy, good UV stability and
low outgassing in high vacuum. To improve processability, PAI was
blended with PA, PSF, or PEST .
Polyetherimide (PEI, has high tensile modulus (even at elevated
temperatures), approaching that of many glass-reinforced resins.
Commercial PEI blends include these with PC or with PPS.
Polyimidesulfone (PISO) was introduced in 1986 (Tg = 249-349°C). This
transparent resin with flexural modulus of 4.8 GPa and tensile strength of
63 MPa, shown excellent solvent and creep resistance.
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
7- Aromatic Amorphous Polyamides (PARA):
There is a great diversity of amorphous aromatic or semi-aromatic
polyamides (PARA). They have been blended to improve the mechanical
properties and impact strength, as well as to enhance the barrier
properties of the matrix resin to permeation by gases or liquids.
8- Polyarylates (PAr):
These polyesters, [-O-φ-C(CH3)2-φ-CO2-φ-CO-]n (Tg = 188°C, and
HDT = 120-175°C), were introduced in 1974.
Their advantages include transparency, good weatherability and high
HDT. PAr has been blended with nearly all resins.
9- Aliphatic Polyketone (COPO):
This copolymer of carbon monoxide with ethylene and propylene is
semicrystalline, with Tg = 15-20°C, Tm = 110-242°C.
Several blends of COPO have been patented, e.g., with SAN (miscible
blends), PA-6 and SEBS-MA , with TPU , with POM and PVPh .
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
10- Blends with Rigid-rod Polymers:
Three types of blends belong to this group:
A-Molecular composites, i.e., the molecular LCP solutions
B-Immiscible blends of LCP(Liquid Crystalline Polymers)
C-Blends of electro-conductive polymers.
A: Molecular Composites
In fiber-reinforced composites, the absolute size of the reinforcing
fibers is not important, but good adhesion to matrix and the length-todiameter ratio of the fiber, L/D≥ 500 are .
Accordingly, reduction of the reinforcing particle size from, e.g., GF or
CF, to rigid-rod molecules seems desirable. If the reinforcement is to be
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
provided by individual macromolecules, the rigid-rod polymer must form
molecular solution in selected thermoplastic resin. Such systems are
known as molecular composites, MC, first generated in the late 1970’s .
MC can be prepared by dissolution of either the rigid-rod polymer in a
monomer that subsequently can be polymerized, or by dissolving
monomer of the rigid-rod polymer in a thermoplastic resin, then
polymerizing it.
The selections of the soluble monomer/polymer pair, as well as control of
the polymerization and phase separation rates are critical.
B: Liquid Crystal Polymers (LCP)
LCP’s are mainly used for injection molding of parts that require exact
dimensions and high performance.
Large quantity of LCP is used in blends. These are immiscible, highly
oriented systems.
In blends LCP can:
(i) Improve processability of engineering and specialty polymer
(ii) Enhance crystallization of semicrystalline polymers
(iii)Improve stiffness and other mechanical properties in applications
where fatigue strength is important , provide external protective layer for
solvent and/or abrasion sensitive resins, etc.
C: Electro-Dissipative and –Conductive Blends
Most organic polymers are insulators. However, there are applications
requiring dissipation of the electrostatic charge (ESD) or even electrical
conductivity (ECP) that would be comparable to that of metals.
The ESD materials should have the surface resistivity 1012≥ R ≥ 105 Ω
cm. The resistivity of ECP should be: 105≥ R ≥ 10-2 Ω cm.
The ESD behavior can be provided by blending in a flexible-chain
polymer with an active –OH or –SH group, viz. polyvinyl alcohol
(PVAl), ethylene-vinylacetate (EVAc), polyvinylphenol (PVPh), a
copolymer of ethylene oxide and epichlorohydrin (EO-CHR), maleated
copolymer, aliphatic polysulfides, etc. These low performance resins
have been incorporated into a variety of alloys and blends .
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
By contrast, the ECP must have conjugated rigid-rod macromolecules.
Several such polymers show high electrical conductivity (usually after
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
doping), viz. polyacetylene (PAc), polyaniline (PANI), polypyrrole
(PPy), polyparaphenylenes (PPP), or poly-3-octyl thiophene (POT).
The resins are expensive, difficult to process, brittle and affected by
ambient moisture, thus blending is desirable.
Conduction Mechanism:
Biodegradable Blends:
Biodegradability has been explored in agriculture to prevent excessive
moisture loss and weeds growth, and to alleviate the recyclability
problems — an agricultural film should last as long as it is needed, then
disintegrate under the influence of either microorganisms and/or UV
irradiation. Most biopolymers are biodegradable, e.g., a large family of
polysaccharides. They have been used in biodegradable blends with
synthetic polymers.
Lec-6: Specialty polymers & Their blends…………………..Eng.Auda Jabbar M.Sc.
Some synthetic polymers, viz. PET, is susceptible to biodegradation
when copolymerized with polylactones.
Polymers with controlled, reversed miscibility, viz. polyglycoles, are
also biodegradable.
Polymers with carbon backbones, viz. PE or PP may be susceptible to
biodegradation after incorporation of ketone side groups, -C(R)(COR’)- .
The biodegradable polymer blends are often prepared by blending a
thermoplastic resin with a biodegradable one .
Blending must produce dispersion that after disintegration of the
biodegradable part the thermoplastic powder will not contaminate the
environment.
Blending and Recycling:
Three basic methods of recycling have been used:
(i) Direct, where cleaned resins are incorporated into virgin material
(ii) Reprocessing the commingled plastics either by blending , or
transforming into plastic wood or plastic concrete
(iii) Feedstock type that may involve depolymerization or pyrolysis.
To the following text, only the method (ii) is important. It can be
subdivided into:
(1) Compatibilization and upgrading of resins in direct recycling
(2) Compatibilization and upgrading of commingled plastics for
reprocessing
(3) Recycling of polymer blends .
To compatibilize a multicomponent blend one may:
(i) add at least one ingredient with highly reactive groups that can
interact with several polymeric components, e.g., ethylene-acrylatemaleic anhydride
(ii) add a low molecular weight additive that at different stages of the
reactive blending binds to different components, viz., ethyleneglycidylmethacrylate.
(iii) add a co-solvent.
The morphology can be stabilized by:
1- thick interphase
2- partial crosslinking
3- addition of an immiscible polymer with a suitable spreading
coefficient .
The adhesion between the phases in the solid state is improved by:
(i) addition of a copolymer that covalently bonds the phases
(ii) reduction of size of the crystalline domains
(iii) adequate adhesion, e.g., by the use of polyetherimine, PEIm
(iv) dispersing at high stresses, either in the melt or in solid state.