System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
Initializing memory for ECC
...
c2821 platform with 786432 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
***AT THIS POINT LAUNCH BREAK SEQUENCE **** (using Tera Term Terminal is ALB + B )
Upgrade ROMMON initialized
PC = 0xbfcd0d54, Cause = 0x2000, Status Reg = 0x3040a803
monitor: command "boot" aborted due to user interrupt
rommon 1 > confreg 0x2142
<<===== type this command when rommon appears
You must reset or power cycle for new config to take effect
rommon 2 > reset
==== enter this command
c2821 platform with 786432 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0x3f7ee20
Self decompressing the image :
##################################################################################
##################################################################################
##################################################################################
##################################################################################
##################################################################################
## [OK]
Smart Init is enabled
smart init is sizing iomem
ID
0003E8
MEMORY_REQ
TYPE
0X00474800 C2821 Mainboard
0X0014B430 Onboard PVDM2 SIMM
0X00264050 Onboard VPN
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
----------------------------------------------TOTAL:
0X00CF9828
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 14Mb.
Using 1 percent iomem. [14Mb/768Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(3)T4, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 24-May-12 01:37 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Installed image archive
Cisco 2821 (revision 53.50) with 772096K/14336K bytes of memory.
Processor board ID FHK0946F02E
2 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
255488K bytes of ATA CompactFlash (Read/Write)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: n
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!By default, the following "voice service voip"
!!sub-command is enabled:
!!
!! ip address trusted authenticate
!!
!!
!!
!!
!!The command enables the ip address authentication
!!
!!on incoming H.323 or SIP trunk calls for toll fraud !!
!!prevention supports.
!!
!!
!!
!!Please use "show ip address trusted list" command
!!
!!to display a list of valid ip addresses for incoming !!
!!H.323 or SIP trunk calls.
!!
!!
!!
!!Additional valid ip addresses can be added via the
!!following command line:
!! voice service voip
!! ip address trusted list
!!
!!
!!
!!
!! ipv4 <ipv4-address> [<ipv4 network-mask>]
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!
===type no or n.
Press RETURN to get started!
*Dec 11 00:44:42.607: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to:
Initialized
*Dec 11 00:44:42.615: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Dec 11 00:44:44.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed
state to up
*Dec 11 00:44:44.187: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
*Dec 11 00:44:44.187: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Dec 11 00:44:45.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0,
changed state to down
*Dec 11 00:44:45.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1,
changed state to down
*Dec 11 00:44:50.491: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to
administratively down
*Dec 11 00:44:50.491: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to
administratively down
*Dec 11 00:44:53.227: %SYS-5-RESTART: System restarted -Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(3)T4, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 24-May-12 01:37 by prod_rel_team
*Dec 11 00:44:53.231: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Dec 11 00:44:53.631: %DSPRM-5-UPDOWN: DSP 1 in slot 0, changed state to up
*Dec 11 00:44:53.663: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 11 00:44:53.663: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Dec 11 00:44:53.663: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 11 00:44:53.663: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Dec 11 00:44:55.023: %DSPRM-5-UPDOWN: DSP 2 in slot 0, changed state to up
Router>
Router>en
===== at Router prompt type enable or en
Router#
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#config-register 0x2102 ======== type this command
Router(config)#end
=== type end to exit
Router#wr
=== type wr to save changes.
Building configuration...
*Dec 11 00:45:19.871: %SYS-5-CONFIG_I: Configured from console by console[OK]
Router#
Router#reload
==== type this command to reload
Proceed with reload? [confirm] == enter to confirm
*Dec 11 00:45:28.351: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload
Command.
System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2009 by cisco Systems, Inc.
Initializing memory for ECC
...
c2821 platform with 786432 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0x3f7ee20
Self decompressing the image :
##################################################################################
##################################################################################
##################################################################################
##################################################################################
##################################################################################
## [OK]
Smart Init is enabled
smart init is sizing iomem
ID
0003E8
MEMORY_REQ
TYPE
0X00474800 C2821 Mainboard
0X0014B430 Onboard PVDM2 SIMM
0X00264050 Onboard VPN
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
----------------------------------------------TOTAL:
0X00CF9828
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 14Mb.
Using 1 percent iomem. [14Mb/768Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(3)T4, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 24-May-12 01:37 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Installed image archive
Cisco 2821 (revision 53.50) with 772096K/14336K bytes of memory.
Processor board ID FHK0946F02E
2 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
255488K bytes of ATA CompactFlash (Read/Write)
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!By default, the following "voice service voip"
!!sub-command is enabled:
!!
!! ip address trusted authenticate
!!
!!
!!
!!
!!The command enables the ip address authentication
!!
!!on incoming H.323 or SIP trunk calls for toll fraud !!
!!prevention supports.
!!
!!
!!
!!Please use "show ip address trusted list" command
!!
!!to display a list of valid ip addresses for incoming !!
!!H.323 or SIP trunk calls.
!!
!!
!!
!!Additional valid ip addresses can be added via the
!!following command line:
!! voice service voip
!! ip address trusted list
!!
!!
!!
!!
!! ipv4 <ipv4-address> [<ipv4 network-mask>]
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!
Press RETURN to get started!
*Dec 11 00:47:47.611: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to:
Initialized
*Dec 11 00:47:47.619: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Dec 11 00:47:49.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed
state to up
*Dec 11 00:47:49.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
*Dec 11 00:47:49.191: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Dec 11 00:47:50.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0,
changed state to down
*Dec 11 00:47:50.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1,
changed state to down
*Dec 11 00:47:51.687: %SYS-5-CONFIG_I: Configured from memory by console
*Dec 11 00:47:53.623: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to
administratively down
*Dec 11 00:47:53.635: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to
administratively down
*Dec 11 00:47:56.307: %SYS-5-RESTART: System restarted -Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(3)T4, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 24-May-12 01:37 by prod_rel_team
*Dec 11 00:47:56.311: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Dec 11 00:47:56.511: %SYS-6-BOOTTIME: Time taken to reboot after reload = 147 seconds
*Dec 11 00:47:56.711: %DSPRM-5-UPDOWN: DSP 1 in slot 0, changed state to up
*Dec 11 00:47:56.743: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 11 00:47:56.743: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Dec 11 00:47:56.743: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Dec 11 00:47:56.743: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Dec 11 00:47:58.111: %DSPRM-5-UPDOWN: DSP 2 in slot 0, changed state to up
Router>en
Router#
==== type enable and you are done. 