Sophya You
Home Account FAQ About Log out Subscribe now
true
tfa4_216883310_ null
810966
Drawing Procedure Review
1. Which measurement in Figure D1003.03.02 is 1 7/16"?
A
B
C
D
2. What should be done when drawing circles with a compass?
Use both hands, one on each leg of the compass
Lean the compass
Measure the circumference
Use a short, back and forth motion
3. Which measurement in Figure D1003.03.02 is 1 3/4"?
A
B
C
D
4. What is the measurement below?
.3
30
17
3
5. What is the measurement below?
.7mm
7mm
23mm
17mm
6. What is the decimal equivalent of 1/8"?
.0625
.375
.250
.125
7. What is the measurement below?
.75
2.25
17.5
1.75
8. What is the decimal equivalent of 3/8"?
.250
.750
.375
.625
9. Which would NOT be used to draw parallel lines?
Drafting machine
T-square
Protractor
Parallel edge
10. Shapes mirrored about the center lines are:
Symmetrical.
Similar.
Matching.
Uniform.
11. What is the diameter of a R5/8 circle?
13/16
1 1/4
3/8
5/16
12. What is the measurement shown below?
3 1/4"
3 3/8"
3 9/16"
3 5/8"
13. Identify the CENTER line in Figure D1003.03.01.
A
B
C
D
14. What is the radius of a Ø1 5/8 circle?
2 5/16
3/8
1/4
13/16
15. What is the obtuse angle being measured below?
155°
57°
43°
143°
16. What is the measurement on the MECHANICAL DRAFTER'S scale below?
2'-6"
2 1/2"
41'1/2"
43'-6"
17. What is the fractional equivalent of .625?
3/8
1/16
3/16
5/8
18. What should be darkened first on a pencil drawing?
Arcs and circles
Object lines
Hidden lines
Phantom lines
19. What is the BEST method for centering a SYMMETRICAL, one-view drawing?
Subtract the width of the drawing from the availible space and then divide by three
Subtract the width of the drawing from the availible space
Use the corners of the paper (or work space) to draw diagonals
Estimate, no need to center it by any process
20. What is the measurement below?
5.5
.5
15
5
21. What is the measurement below?
25.6
15
1.5
14.5
22. Which drawing scale would be BEST for a Ø1/4" washer on a "A" size sheet?
1:1
1:4
1:2
4:1
23. What is the angle of the line illustrated below?
45°
60°
75°
15°
24. Which drawing scale would be BEST for a 24" wheel on a "A" size sheet?
4:1
1:4
1:1
1:2
25. Which drawing scale would be BEST for a small paperclip on a "B" size sheet?
1:2
4:1
1:1
1:4
26. What is the decimal equivalent of 7/8"?
.6875
.50
.875
.250
27. What is the measurement below?
.4
.5
.3
.2
28. What is the measurement below?
.1
.2
.4
.3
29. Which measurement in Figure D1003.03.02 is 1 7/8"?
A
B
C
D
30. What is the diameter of a R1 1/2 circle?
3 1/4
3
3/4
1/4
31. Identify the VISIBLE line in Figure D1003.03.01.
A
B
C
D
32. What is the decimal equivalent of 3/4"?
.75
.125
.5
.250
33. What is the measurement below?
.4
.1
.2
.3
34. What is the technique shown below?
Drawing 45° lines
Drawing parallel lines
Drawing perpendicular lines
Drawing vertical lines
35. What is the technique shown below?
Measuring the altitude of the triangle
Drawing a line at 30°
Drawing a line parallel to the given line
Dividing the line into two equal parts
36. When drawing an object one-half its true size, which scale would be indicated on your
drawing?
NTS
SCALE 1:1
SCALE 2:1
SCALE 1:2
37. Which statement is true reguarding LINE THICKNESS?
The Center line is thicker than a Visible (Object) line.
It does not make any difference.
The Visible (Object) line is thicker than a Center line.
The Center line and Visible (Object) line are the same thickness
38. What is the decimal equivalent of 3/8"?
.0625
.125
.375
.250
39. Which drawing scale is equivalent to 1:2?
Twice full size
1/2 full size
2 =1
1/2 = 12
40. Which drawing scale would be BEST for a 36" x24" gasket on a "A" size sheet?
1:4
1:2
4:1
1:1
41. What is the radius of a Ø3/4 circle?
1/4
3/16
3/8
1 1/2
42. Identify the HIDDEN line in Figure D1003.03.01.
A
B
C
D
43. STANDARD TRIANGLES can be used to construct lines in multiples of:
15°
20°
10°
5°
44. Where is information such as the drafter, date, and scale located?
Title block
Local notes section
Revision column
Parts list
45. What is the measurement illustrated below?
42 millimeters
41 millimeters
21 millimeters
.42 meters
46. Which measurement in Figure D1003.03.02 is 1 1/4"?
A
B
C
D