Training modules
1.
What’s new in SmartTool?
2.
What can SmartTool do for my borehole?
3.
Meet the hardware
4.
MeasureIT software that sets-up, runs, calculates & checks.
5.
Practical exercises with the SmartTool.
6.
DisplayIT software, showing off the results.
7.
The Single-shot StoreIT menus.
8.
The Multi-shot StoreIT menus.
1 What’s new --
SensIT probe -- sealed and unopenable
no plugs or cables
1 What’s new --
StoreIT data pad -- sealed in an Aquapac,
-- hung on a lanyard.
1 What’s new --
SensIT & StoreIT -ten years power - built in,
no batteries or chargers.
no plugs or cables
1 What’s new --
SensIT, StoreIT & your PC -transfer data by automatic fast radio link.
1 What’s new --
Quality assurance system -warns of magnetism or movement
1 What’s new --
SensIT in its pressure barrel
Shock resistant to 6000G
Shockproof to 6000g
Watertight to 4000 metres
2 What can SmartTool do for me? --
Four different tasks
Single-shot survey ----- read data on StoreIT
----- combine data on PC to make …
Multi-shot survey
3D hole path using magnetic azimuth measurement
Orientated survey ----- less than 30m, close to vertical
3D hole path maintaining azimuth with orientation rods
Tool or Core orientation, using
Gravity roll angle ---- for inclined holes
Magnetic toolface angle --- for vertical holes
2 What can SmartTool do for me? --
Eight measurements at each DEPTH (shot) recorded by SensIT
1 Dip (Inclination) of hole
2 Direction (azimuth) of hole
for Positional Survey
3 Gravity Roll angle of SensIT 4 Toolface angle of SensIT
for Orientation
5 Magnetic field strength
6 Magnetic dip angle
for Quality Assurance
7 Temperature of SensIT
8 Depth, time and date
for the record
2 What can SmartTool do for me? --
Survey
2 What can SmartTool do for me? --
Orientation
Setting the zero Gravity Roll Angle
2 What can SmartTool do for me? --
Orientation
Setting the zero MagneticToolface Angle
2 What can SmartTool do for me? --
Quality assurance.
The Earth’s Gravitational Field
2 What can SmartTool do for me? --
Quality assurance.
The Earth’s Gravitational Field
If Grav. Field is not 1.00 G, then SensIT is moving;
Dip and Azimuth may both be unreliable
2 What can SmartTool do for me? --
Quality assurance.
The Earth’s magnetic field
Variation - angular difference between True North and Magnetic North
Magnetic Field Strength - the force of the earth's magnetic field
Magnetic Dip Angle - angle the field force lines make with the horizontal
At each place on the earth's surface, these values are known.
2 What can SmartTool do for me? --
Quality assurance.
Set the threshold for the local magnetic environment
2 What can SmartTool do for me? --
Quality assurance.
Identify the unreliable azimuths
Training modules
1.
What’s new in SmartTool?
2.
What can SmartTool do for my borehole?
3.
Meet the hardware
4.
MeasureIT software that sets-up, runs, calculates & checks.
5.
Practical exercises with the SmartTool.
6.
DisplayIT software, showing off the results.
7.
The Single-shot StoreIT menus.
8.
The Multi-shot StoreIT menus.
Training modules
1.
What’s new in SmartTool?
2.
What can SmartTool do for my borehole?
3.
Meet the hardware
4.
MeasureIT software that sets-up, runs, calculates & checks.
5.
Practical exercises with the SmartTool.
6.
DisplayIT software, showing off the results.
7.
The Single-shot StoreIT menus.
8.
The Multi-shot StoreIT menus.
7
The StoreIT Single-shot menus
DATA, Shows Survey
SETTINGS
#, Hole Ref. & Depth
Azimuth
Inclination
Mag Field
Mag Dip
G.R/angle
M.T/face
Time
Date
Temperature
>>Press SETTINGS to exit
Timer }
+/Depth }3
+/
Hole ref. }
+/- OK
Enter Archive
OK
Set Mag Field/Dip OK
Zero G.R/angle
OK
Zero M.T/face
OK
Set time
+/- OK
Set date
+/- OK
Multi-shot mode? OK
>>Press NEW to start timer
Here the DATA button displays each reading from a Single-shot
survey.
8
The StoreIT Multi-shot menus
First survey press New
Next Survey press New
SETTINGS 1
Change SETTINGS 2
Hole ref.
}
Next Depth
Start depth
}
Depth interval
Depth interval } 5
End survey
Direction
}
>>Press DATA
Time interval }
to continue survey
Set time
Set date
Single-shot mode?
>>Press DATA for first survey
Change SETTINGS 3
Hole ref.
Start depth
Depth interval
Direction
End session -download
>>Press DATA
for next survey
• Here the DATA button is only a switch from the SETTINGS menus back
to the survey operation.Then, to start a survey, press NEW