SCHEMATIC MANOEUVRE ILLUSTRATIONS
SCHEDULE P-15.
Take-off procedure
( not judged, not scored )
wind
1200
Security line
P-15.01: Golf Ball with two ½ rolls
½ roll
½ roll
P-15.01.01
P-15.01: Golf Ball with two ½ rolls
½ roll
P-15.01.02
P-15.01: Golf Ball with two ½ rolls
½ roll
P-15.01.03
P-15.01: Golf Ball with two ½ rolls
½ rolls on middle of the lines.
½ roll
All radii are equal.
½ roll
P-15.01.04
P-15.02: Half Square Loop on Corner with ½ roll
½ roll
P-15.02.01
P-15.02: Half Square Loop on Corner with ½ roll
½ roll on middle of the line.
All radii are equal.
45°
45°
P-15.02.02
P-15.03: Double Immelmann with two knife edge flights
¼ roll
¼ roll
During the knife edge
the wing must be in
the vertical plane.
¼ roll
¼ roll
P-15.03.01
P-15.03: Double Immelmann with two knife edge flights
The half loops must follow
immediately after the ¼ rolls .
There must be no line between
the half loops and the ¼ rolls.
All radii are equal.
P-15.03.02
P-15.04: Half Square loop with ½ roll
½ roll
P-15.04.01
P-15.04: Half Square loop with ½ roll
1/2 roll on middle of the line.
All radii are equal.
P-15.04.02
P-15.05: Stall Turn with 1 ¼ roll up, ¾ roll down
1 ¼ roll
3/4 roll
P-15.05.01
P-15.05: Stall Turn with 1 ¼ roll up, ¾ roll down
Pivot on CG
Stop before pivot
1 ¼ roll
Two wing spans or more
– zero points!
3/4 roll
1 ¼ roll and ¾ roll centered
on middle of the lines.
All radii are equal.
P-15.05.03
P-15.06: Half Reverse Cuban 8 with ½ roll
½ roll
P-15.06.01
P-15.06: Half Reverse Cuban 8 with ½ roll
½ roll
P-15.06.02
P-15.06: Half Reverse Cuban 8 with ½ roll
1/2 roll on middle of the line.
All radii are equal.
45°
P-15.06.03
P-15.07: Roll Combination with consecutive three
1/6 rolls, three 1/6 rolls in opposite direction
1/
6
1/
6
1/
6
roll roll roll
1/
6
1/
6
1/
6
roll roll roll
P-15.07.01
P-15.07: Roll Combination with consecutive three
1/6 rolls, three 1/6 rolls in opposite direction
The 1/6 rolls must have the same roll rate.
1/
6
1/
6
1/
6
roll roll roll
1/
6
1/
6
1/
6
roll roll roll
Lines between part rolls must be short and of equal length.
Between part rolls in opposite direction there must be no line.
P-15.07.02
P-15.08: Pull-Push-Push Humpty-Bump with ¾ roll up,
up, ¾ roll down (Option: ½ up, ½ roll down)
¾ roll
¾ roll
P-15.08.01
P-15.08: Pull-Push-Push Humpty-Bump with ¾ roll up,
up, ¾ roll down (Option: ½ up, ½ roll down)
¾ roll
¾ rolls in middle of the lines.
¾ roll
Al radii are equal.
P-15.08.02
P-15.08: Pull-Push-Push Humpty-Bump with ¾ roll up,
up, ¾ roll down (Option: ½ up, ½ roll down)
Option
½ roll
P-15.08.03
½ roll
P-15.08: Pull-Push-Push Humpty-Bump with ¾ roll up,
up, ¾ roll down (Option: ½ up, ½ roll down)
Option
½ roll
P-15.08.04
½ roll
P-15.08: Pull-Push-Push Humpty-Bump with ¾ roll up,
up, ¾ roll down (Option: ½ up, ½ roll down)
Option
½ rolls on middle of the lines.
Al radii are equal.
P-15.08.05
P-15.09: Top Hat Inverted Spin with 2 ½ turns
P-15.09.01
P-15.09: Top Hat Inverted Spin with 2 ½ turns
Snap entry - 0 points!
Spiral dive - 0 points!
Forced entry: downgrade.
All radii are equal.
P-15.09.02
P-15.10: Pull-Knife-Edge-Push Humpty-Bump
with ½ roll down
Half Knife Edge loop
During the knife-edge
the wing must be in the
vertical plane.
½ roll
P-15.10.01
P-15.10: Pull-Knife-Edge-Push Humpty-Bump
with ½ roll down
½ roll on middle of the line.
Al radii are equal.
P-15.10.02
P-15.11: Reverse Cuban 8 with consecutive two ¼ rolls,
consecutive two ½ rolls in opposite directions
½ roll
½ roll
¼ roll
Rolls centered on
middle of the lines .
¼ roll
P-15.11.01
P-15.11: Reverse Cuban 8 with consecutive two ¼ rolls,
consecutive two ½ rolls in opposite directions
All part rolls must have the same roll rate.
Lines between part rolls must be short and of equal length.
Between part rolls in opposite direction there must be no line.
½ roll
45°
½ roll
¼ roll
All radii are equal.
¼ roll
P-15.11.0“
P-15.12 Figure 9 with consecutive four ¼ rolls up
¼ roll
¼ roll
¼ roll
¼ roll
P-15.12.01
P-15.12 Figure 9 with consecutive four ¼ rolls up
¼ rolls centered on
middle of the line.
¼ roll
¼ roll
¼ roll
¼ roll
P-15.12.02
Al radii are equal.
P-15.13: Hour-Glass with ½ roll, roll, ½ roll
½ roll
roll
½ roll
P-15.13.01
P-15.13: Hour-Glass with ½ roll, roll, ½ roll
45°
P-15.13.02
P-15.13: Hour-Glass with ½ roll, roll, ½ roll
45°
P-15.13.03
P-15.13: Hour-Glass with ½ roll, roll, ½ roll
45°
Rolls on middle of
the lines .
All radii are equal.
P-15.13.04
P-15.14: Stall Turn with consecutive two ¼ rolls down
Pivot on CG
Stop before pivot
P-15.14.01
P-15.14: Stall Turn with consecutive two ¼ rolls down
Pivot on CG
¼ roll
¼ roll
P-15.14.02
P-15.14: Stall Turn with consecutive two ¼ rolls down
Two wing spans or more – zero
points!
Pivot on CG
¼ roll
¼ rolls on middle of the
line.
¼ roll
All radii are equal.
P-15.14.03
P-15.15: Upline with consecutive two rolls in opposite
directions
P-15.15.01
P-15.15: Upline with consecutive two rolls in opposite
directions
Rolls centered on middle of
the line.
45°
All radii are equal.
Between rolls in opposite direction there must be no line.
P-15.15.02
P-15.16: Split S with ½ roll
½ roll
P-15.16.01
P-15.16: Split S with ½ roll
The half loops must follow
immediately after the ½ roll.
½ roll
P-15.16.02
P-15.17: Avalanche with snap roll on top
P-15.17.01
P-15.17: Avalanche with snap roll on top
Snap roll may be positive or
negative.
Loop must be
round.
If snap roll = barrel roll or
aileron roll:
Severe downgrade > 5 pts.
P-15.17.02
Landing procedure
( not judged, not scored )
The direction of the landing may be different to the
take off.
wind
1200
Security line
Forget WHO is flying
(friend, rival, countryman, flier from other nation)
Forget WHAT is flying
(2-stroke, 4-stroke, electric, turbine, rubber-power)
LOOK ONLY AT LINES DESCRIBED IN THE SKY!
(and the precision, smoothness, positioning, and size)
Thank you!
Peter Uhlig, September 2013