Aria – iP 60
What connection ? CO via GW or VoIB Card?
ARIA IP - 60

Introduction
This document explains the configuration that is required on ERICSSON-LG PABX systems when
SIP trunks are configured using the Goldtel SIP trunk service.
Basic call setup (Incoming & Outgoing calls) was tested with CLI (Calling Line Identification) presentation.
Please note that this document is Service Provider specific (Goldtel Telecom) and some of the
Details below are used as examples only.
This document is only applicable to the ERICSSON-LG range of PABX systems .
TEST SETUP CONFIGURATION
Goldtel Service Provider Details
The following information was received from the Service Provider (Goldtel) to complete the tests:
SIP/Proxy/Registrar IP: 196.7.219.35 and 196.7.219.35
SIP Port Number : 5060 (UDP)
Sip account User@Domain
27876300184 @196.7.219.35
27876300184 @196.7.219.35
Authorization Name
27876300184
27876300185
Password cNxxxxxxxx cNxxxxxxxx
Phone Number
27876300184
27876300185

PGM 101 - 103 Slot Configuration
Right Click
If we require 8 VoIP lines then this setting = 8

Numbering Plan
PGM 104 - 109
What if theis is not [1]

IP Settings
PGM 108 Gateway IP = Router IP
PABX IP Address
ADSL Router IP Address
The same range as the PBX
165.165.165.1
192.165.55.202

CO Line Configuration
PGM 140/141/143/146

CO Line Configuration
Co grp 1 = Voip / SIP Trunks on Slot 10 (1 st Choice o/g)
Telkom or other SP lines will be allocated to CO Grp2

CO Line Configuration
Mode 141
Mode 146
Mode 142
This parameter defines the DID digit conversion process for DID digits received from the ISDN or IP
CO line.
After removal of digits, Flexible button 5, the DID number treatment can be a simple conversion (0), no conversion (1) or simple conversion with table look-up (2). PGM231

CO Line Configuration
Mode 146
CO Attr |||

Station Configuration
PGM 111 for all extension
This parameter determines the caller id for a station when employing SIP for a call.
When using SIP, the caller id is based on the CLIP/COLP
(PGM 143 Flexible button 1 and 2) or the User ID defined from the SIP User ID Table index (PGM 501) entered here.
{500&501 with 340}
Invalid entry Message- Mode 111 FK23 = 1 Sip User ID
Also Mode 231- 087 630 0 184 The last 3 digits = 184 Open
Now set day & night destination ringing = 100

Station Configuration
PGM 111 for fax in and out going call

Station Configuration
PGM 114

VOIP Configuration
PGM 340/341 Firewall IP = WAN IP of the Router
IP address of the
Gateway Card VoIB
ADSL Router IP
Address

VOIP Configuration
PGM 340 SIP ATT 1 (Actually PGM 500)

SIP Trunk Registration
PGM 340 SIP ATT 11 (Actually PGM 501)

Net working CO line configuration
PGM 322

COLP Table configuration
PGM 200/201

Flexible DID Table
PGM 231
Invalid entry Message- Mode 111 FK23 = 1 Sip User ID Error code “Cause 400”
Also Mode 231- 087 630 0 184 The last 3 digits = 184 Open

COLP Table configuration
PGM 450 Flex 15
N.B. After this step please reset IP60 system

Mode 200
087
Mode 143 – DiD=2
DiD REM = 1
DiD Enblock =1 On
Mode 146 – DiD RCV =3
DiD Dig = #***
#1**
Mode 231 – 550 – Ring Sta 100=150
Mode 201
6300
Mode 231
551

END