Arcona 400 - Nexus Marine

advertisement
ARCONA
400
www.nexusmarine.se
System Suggestion
System Suggestion
NX2 Race Software
The FDX, Fast Data eXchange, is the protocol that allows the PC to become a fully integrated
NX2 instrument when connected to the NX2 Server.
The NX2 Race software free of charge with all NX2 FDX Servers, so bring your PC onboard
and use all capabilities that the NX2 system can offer!
The NX2 Race software enables you to monitor all data in analogue or digital format, create
waypoints and routes, logging all data, calibrate the transducers and system setup. You can
also activate the NX2 Steer Pilot, set backlight levels on the instruments etc. In short - control
the whole NX2 system.
The latest NX2 Race software can also be downloaded on the web for use with Silva NX2 FDX
server based systems. The NX2 Sail Performance software will not work with NMEA0183
protocol.
Connect your PC direct to the NX2 FDX Server PC port that normally is operating in
NMEA0183 mode. When the NX2 Race software is started, the Server will automatically
switch to FDX mode to be fully integrated with the NX2 system.
System Suggestion
NX2 General
Every unit/instrument with the name ”NX2” can be connected to the network. You can
configure the system in pretty much which way you want with up to 32 NX2 units connected to
the network. The Server must be a part of the system.
Server:
Is the brain of the
NX2 system. To the
Server you will
connect all
transducers you
want information
from, instruments in
which you want to
see the information
and all other non
NX2 units, e.g. a
PC, you want to
have in the system.
The Server must
be used together
with the Multi
Control and
Remote Control.
Steer Pilot
Analog Wind
Shows you the
Shows you the
wind angle.
difference from a
set reference
True or apparent
angle. E.g. The
compass course,
bearing to
waypoint, course to
steer etc.
Steer Pilot must be
controlled from the
Multi Control and/or
the Remote
Control. It can also
be set from a push
button.
Speed Trim
Compass
Presents speed Presents current
changes in per
course.
cent since last
trimming.
System Suggestion
Multi Control:
Multi XL:
Wind Data
GPS Navigator
Compass Data
Is an instrument that
is able to present all
information (two
lines of information
at the same time)
available in the NX2
network. This
instrument can also
control all the
information in the
Server e.g. settings
and calibrations. It
also has the feature
to be used as a
remote control for
other instruments.
Works basically as
the Multi Control.
The difference is
that it has larger
digits.
Multi XL must be
controlled from the
Multi Control and/or
the remote control.
Digital wind display.
Shows both TWA &
AWA at the same
time. Can also
present TWS, AWS,
BSP among other
things. TBS can be
presented if a PC is
connected to the
server.
Shows current
position, SOG, COG
and other satellite
based information.
Also has the ability
to enter and edit
waypoints, routes
and sailplans in the
instrument.
A digital compass
display that shows
the boats current
course both in
numbers and
graphic. Has the
ability to use BTW,
CTS and wind as
steer reference.
Speed
Presents BSP,
distance, maximum
BSP, average BSP
and timer with
countdown function.
It can be a
standalone
instrument.
Mast Bracket
Fitting for Multi XL
instruments on the
mast. Carbon fibre
System Suggestion
NX2 TRANSDUCERS.
NX2 AUTOPILOT.
NX2 Autopilot consists, for boats up to app. 45 feet, of 5 parts. For
boats above app. 45 feet the integrated drive unit, HP40, will be
split in to two parts; a separate ram and a separate pump.
GPS ANTENNA
• Integrated hydraulic drive unit:
The unit that affects the rudder to move when the
autopilot is engaged. Will be mounted a tiller arm
attached to the rudder stock or the quadrant.
52mm THF
LOG
TRANSDUCER
• Servo unit:
Connection box and brain for the autopilot system.
DEPTH
TRANSDUCER
• Rudder angle transmitter:
Important to give the autopilot as accurate rudder
information as possible.
• Compass transducer HPC:
Gives the autopilot information about the actual course which will
be compared to the set reference course. The compass
transducer shall be connected to the network.
HPC measures compass heading, roll and pitch.
WIND
TRANSDUCERS.
COMPASS
TRANSDUCERS.
SERVO
• Instrument that can control the autopilot:
From the instrument you will activate/deactivate the autopilot.
This instrument can be:
- NX2 Autopilot instrument
Instrument Location Overview
ARCONA
400
Located on mast
Located by companionway
Located below deck
Located by the nav station
Detailed Specification
ARCONA
400
Nav station
Multi
Control
Suggested options
Wind Data
Companionway
Wind
Data
Multi
Control
Multi
Control
Multi
Control
Mast Braket
Steer
Pilot
Multi XL
Multi XL
Wind
Analog
Speed Trim
Multi XL
Compass 125
Autopilot
Servo Unit
Mast Bracket
Linear Drive
NX2000
NX1500
Q: Product name:
Part no
1 Multi Control
incl. Server
22118-21
log transducer
depth transducer
1 Compass transd.HPC 23003
1 GPS antenna
21970-3
1 Wind transducer
22511 or 22462
Q: Product name:
Part no
2
1
1
3
1
1
1
22117-3
22117-4
22115-02
21680-1
69995-4
22117-7
69989-12
Multi Control
Wind Data
Steer Pilot
Multi XL
Mast Bracket
Autopilot instr
Linear Drive
Product name:
Part no
Wind Data
Multi Control
Analog Wind
Speed Trim
Autopilot
Linear Drive
Servo Unit
Compass 125
VHF NX2000
VHF NX1500
22117-4
22117-3
22115-01
22115-03
22117-7
69989-12
21035-2
35074
28320-1
28315
Download
Related flashcards
Create Flashcards