MECHANICS (1EM105B) – PRACTICAL
EXPERIMENT 1
DATE: 25 AUGUST 2026
LECTURER: ADEGBOLA T.A
GROUP 12 MEMBERS
SURNAMES
MAKHAFOLA
MASILA
MAGANYELE
INITIALS
T.K
O
L.M
STUDENT NR
231594329
261055589
241710491
TABLE OF CONTENT
1. Declaration .......................................................................................................................................................3
2. Introduction .....................................................................................................................................................3
3. Aim ........................................................................................................................................................................3
4. Equipment.........................................................................................................................................................3
5. Experimental Procedure ...........................................................................................................................3
6. Results .................................................................................................................................................................4
7. Discussion and Conclusion .......................................................... 4 ......................................................
8. Annexure ...........................................................................................................................................................5
9. References .................................................................................... 5
1. DECLARATION
I hereby confirm that this Mechanics practical experiment was carried out as part of the
requirements for the Mechanics module in the Electrical Engineering programme at
Tshwane University of Technology. I declare that the work presented in this report was
completed by the members of our group and that the information and results included
are based on the experiment that we performed.
SURNAME & INITIALS
SIGNATURE
2. INTRODUCTION
The purpose of this experiment was to investigate the resultant produced when three
different forces act simultaneously. The resultant was determined using three
approaches: the practical force-table method, mathematical addition of vector
components, and graphical vector addition.
The experiment also involved determining an equilibrant force. The equilibrant is the
force required to balance the resultant of the other forces and bring the system into
equilibrium.
3. AIM
The objective of this practical was to use a force table to determine experimentally the
magnitude and direction of a force capable of balancing three applied forces.
The experimental result was then compared with values obtained mathematically by
resolving the forces into their horizontal and vertical components, as well as with the
graphical solution.
4. EQUIPMENT
The following apparatus was used during the experiment:
•
Vector board / force table
•
Four pulley clamps Four pulleys
•
Four mass hangers
•
Set of masses
•
Strings
5. EXPERIMENTAL PROCEDURE
The experiment was performed by attaching three forces to the force table at specified
angles. A fourth pulley and mass hanger were then introduced to produce a balancing
force.
The fourth force was determined by adjusting its position and the mass attached to it
through trial and error until the system reached equilibrium. This balancing force is
referred to as the equilibrant (FE).
Since the equilibrant acts in the opposite direction to the resultant, its magnitude is
equal to that of the resultant but its direction differs by approximately (180^\circ).
The final mass and angular position of the fourth pulley were recorded once equilibrium
had been achieved.
6. RESULTS
6.1 Experimental Results
FORCE
FA
FB
FC
FD
6.2 Mathematical Calculations
MASS
50 g (0.050 kg)
100 g (0.100 kg)
80 g (0.080 kg)
95 g (0.095 kg)
ANGLE
0°
120°
200°
318°
The individual forces were resolved into their horizontal ((x)) and vertical ((y))
components.
Force (FA) : x = 50cos0° = 50, y = 50sin0° = 0
Force (FB) : x = 10 0cos120° = -50, y = 10 0sin120° = 86.60
Force (FC) : x = 80cos200° = -75.18 , y = 80sin200° = 59.24\
Resultant Components
Rx = 50-50-75.18 = -75.18
Ry = 0 + 86.60 – 27.36 = 59.24
[R]=√Rx2+Ry2 = √(-75.18 2 + 59.242) = 95.8 g
The magnitude of the resultant is therefore:
ΘR = tan-1(Ry/Rx) = tan-1(59.24/-75.18) = 141. 5°
The direction of the resultant is:
ΘE = θR + 180° = 141.5° + 180° = 321.5°
Percentage Error = 1.10%
METHODS
Experimental
MAGNITUDE
95g
DIRECTIONS
318 °
Graphical
95g
318 °
Calculations
95g
321.5 °
Using the experimental value of (95g) and the calculated value of approximately (95.8g):
Note: This recalculated percentage differs from the 1.10% stated in the supplied report.
6.3 Final Comparison
The experimental and graphical results are very close to the calculated result, indicating
that the force-table experiment was reasonably accurate.
7. DISCUSSION AND CONCLUSION
During the practical, several combinations of masses and pulley positions were tested
before the system could be brought into equilibrium. The first trial was performed using
an angle of 330° with a mass of 105g. Another attempt was made at 280° using an 80g
mass.
After making further adjustments to both the mass and the angle, the system reached
equilibrium at approximately 95g and 320°
The results obtained experimentally were close to those determined using vector
calculations. The small difference between the experimental and calculated values may
have resulted from experimental limitations such as friction in the pulleys, slight errors
when reading the angles, or inaccuracies in the masses.
In conclusion, the experiment successfully demonstrated how several forces can be
combined to obtain a resultant force and how an equilibrant can be used to oppose the
resultant and establish equilibrium. The close agreement between the experimental,
graphical, and calculated results confirms the validity of the vector addition method.
8. ANNEXURE
We tried types of masses and angles and after a trial and error we finally got the right
angle and mass. However before we reached the final mass we firstly tried out 330° at
105g and secondly we tried out 280° at 80g.
9. REFERENCES
No external references were used. The experiment was conducted using the practical
instructions and laboratory equipment provided for the Mechanics module at Tshwane
University of Technology.