Dr. Marca Lam
Mechanical Engineering
GLE(09)‐2191
475‐6871
mjleme@rit.edu
Textbook
Askeland, D, et.al.
The Science and
Engineering of
Materials
Cengage Learning
7th Edition
2
1
Materials needed for all products
our everyday lives are influenced by materials:
housing, transportation, clothing, recreation,
etc.
nasa.gov
tlc.howstuffworks.com
1centralpark.com
3
History of Human Civilization
Stone Age
Bronze Age
Iron Age
Steel Age
Space Age, Electronic Age
4
2
Evolution of engineering materials over time
5
Functions of
a Materials Engineer
Selects among competitive materials
Prepares and processes materials
Predicts the properties of materials under
operating conditions
Improves the properties of existing
materials
Creates new materials
6
3
CLASSIFICATION OF MATERIALS
Three basic groups:
metals
ceramics /glass
polymers
Barnes &
Noble @ RIT
www.alibaba.com
7
Metals
Metallic bonding
Atoms
Dense, strong/hard
but deformable to
complex shapes
Fracture toughness –
resistant to impact
Medium melting temp
High electrical/
thermal conductivity
suydam.glogster.com
8
4
Ceramics
and Glass
Ionic/covalent bonding
Low density
Brittle ‐ very hard
High melting temperature
Low electrical/thermal conductivity – good
insulators
High corrosion resistance (sometimes)
chemsite.lsrhs.net
9
Structure‐property relations for Aluminum Oxide: Al2O3
highly perfect single crystal transparent
polycrystalline, GBs scatter portion of reflected light translucent
polycrystalline w/high porosity volume fraction opaque
single crystal
polycrystal:
low porosity
polycrystal:
high porosity
10
5
Polymers
“poly”= many & “mer”= unit
Molecules
Ductile
Low density – lightweight
Low melting temperature
Good electrical/thermal insulators
Be careful of thermal transition temp
◄ Nylon matrix
Broken
nylon ►
fiber
sbio.uct.ac.za
11
Composites
Artificial combinations of materials
Properties of Composites:
Low density
High strength
Good ductility
High temperature
applications
www.designnews.com
12
6
MECHANICAL PROPERTIES
OF MATERIALS
13
Mechanical Properties in
Design and Manufacturing
Determine a material’s behavior when subjected to
mechanical force
‒ Strength (several types)
‒ Elastic Modulus
‒ Ductility
‒ Hardness
Impact
Fracture Toughness
‒ Creep
‒ Fatigue
‒ Wear
‒
‒
Dilemma: mech. prop. desirable to designer, i.e. high
strength, usually make manufacturing more difficult
14
7
Stress‐Strain Relationships
Three types of static stresses:
1. Tensile ‐ stretching the material
2. Compressive ‐ squeezing the material
3. Shear ‐ causing adjacent portions of the material to
slide against each other
Stress‐strain curve ‐ basic relationship that
describes mechanical properties for all three types
15
Linear Spring
F
F = kx
k
http://www.psychometric-success.com/aptitudetests/mechanical-reasoning-tests-springs.htm
x
16
8
Linear Spring
Same material
Same load
Different size sample
F
F
F
1
k2 > k1
k2
2
k1
F
x
F
17
Engineering Stress
Force distributed over area (cross‐sectional
or perpendicular to load)
Tensile stress – load is pulling
Compression stress – load is pushing
Shear stress – load is parallel to cross‐
sectional area
http://www.learneasy.info/MD
ME/MEMmods/MEM30007A/
properties/Properties.html
https://www.pinterest.
com/pin/29934870645
7546388
18
9
Engineering Stress
Tensile stress:
F
A0
where
‐ engineering stress, (psi, MPa)
F ‐ force, normal to A0, (lbf, N)
A0 ‐ original cross‐sectional area,
(in2, mm2)
> 0 tension
< 0 compression
19
Shear Stress
Fs
A0
Fs ‐ force, parallel to A0
A0 ‐ the cross‐sectional area
unit of stress:
Force N
area m 2
1Pa = 1 Nm-2;
Shackelford, 6e
1MPa = 106Pa; 1GPa=109Pa
20
10
Engineering Strain
Gives indication of change in size of sample under load
Normal ‐ tensile or compressive
Change in length
Shear
Change in angle
Normalized so that sample size does not matter
http://study.com/academy/lesson/shear‐strain‐definition‐equation.html
21
Engineering Strain
Nominal tensile strain (Axial strain)
l l0 l
l0
l0
where
= engineering strain (in/in, mm/mm),
l = length at any point (in, mm)
lo = original gage length [in, mm]
> 0 elongation or expansion
Shackelford, 6e
< 0 shrinkage
22
11
Mechanical Properties
Typical Stress‐Strain Curve
Elastic ‐ reversible
2. Plastic ‐ irreversible, permanent
3. Necking region
1.
Fracture
www.benbest.com
23
Elastic Behavior of Materials
load
unload
www.feppd.org
24
12
Plastic Behavior of Materials
https://www.e-education.psu.edu/matse81/node/2104
25
Temp effects on
‐ curve for Iron
https://failuremechanisms.wordpress.com/tag/reinforced-concrete/
Illustration from Callister & Rethwisch, Materials Science & Engineering, An Introduction, 8th ed., J. Wiley & Sons, 2010
26
13
True Stress and Strain
T
True Stress
F
A
where A is instantaneous cross‐sectional area
True Strain
T ln
l
ln 1
l0
If no volume change during deformation:
A0l0=Al
Then
1
T
T ln 1
27
True Stress‐Strain Curve Note: True
stress keeps
increasing,
even beyond
necking.
Means? Metal
becoming
stronger as
strain
increases:
www.engrasp.com
Strain
hardening
28
14
Hooke’s Law
Stress proportional to strain
Engineering stress ‐ use initial area for calculations
True stress ‐ use instantaneous area
29
Hooke’s Law
When strains are small, most of materials are linear
elastic.
Young’s modulus
Tensile:
Shear:
=G
Shear modulus
E
30
15
Poisson’s ratio
z
l z
l0 z
Nominal lateral strain
(transverse strain)
x
Callister, 8e
Poisson’s ratio:
l x
l0 x
lateral strain
x
tensile strain
z
31
Elastic Properties of Materials
Isotropic materials (identical values of property in all
directions): two elastic constants
E 2G (1 )
Anisoptropic materials: more than 2 elastic constants
32
16
33
Yielding and Yield Strength
Yield point
turning point which separate elastic and plastic regions
Yield strength/Yield stress/Elastic limit
stress at yield point
Offset yielding (proof stress)
if it is difficult to determine yield pt, then draw parallel
line starting from 0.2% strain
measure cross pt between parallel line and curve
34
17
Plastic Deformation & Offset Yielding
Typical (gradual) transition
from elastic to plastic
Sudden transition
(yield pt. phenomenon)
Callister, 8e
35
Tensile Strength
TS - highest applied force
Necking
← Failure
Callister, 8e
36
18
Measurement of
ductility:
Ductility
% elongation
% reduction in area
researchgate.net
37
Ductility
Ductility – % elongation
l f l0
100
% EL
l0
lf: fracture length
l0: original gauge length
Ductility – % reduction in area
A0 A f
100
% RA
A
0
Af: cross‐sectional
area at point of
fracture
A0: original cross‐
sectional area
38
19
Tests to Determine Strength
Bend
Tension and Compression
Toughness
Hardness
Creep
Fatigue
Abrasive
39
Tension Testing
40
20
Testing Tensile Properties
Most common test for studying
stress‐strain relationship,
especially for metals
In the test, a force pulls the
material, elongating it and
reducing its diameter
‒ Tensile force applied
‒ Resulting elongation of material
©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e
41
Tensile Test Specimen
ASTM (American Society for Testing and Materials) specifies
preparation of test specimen & test procedure
Different for round and flat samples
http://enterprise.astm.org/SUBSCRIPTION/NewValidateSubscription.
cgi?E8/E8M-HTML
42
21
Tensile Test Setup
Typical tensile testing
machine schematic
©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e
43
Tensile Test Sequence
Typical tensile test progression:
1)
2)
3)
4)
5)
6)
no load
uniform elongation
and area reduction
maximum load
necking (depends on ductility)
fracture
putting pieces back
together to measure
final length
www.southampton.ac.uk/~doctor/QS_4.htm
©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e
44
22
Aluminum Tensile Test
45
Nylon Tensile Test
46
23
Polymers ‐ Tensile Deformation
Molecules begin
disentangling
(Initial Yield
point)
Fracture
point
Chains begin to break
Molecules but disentangling takes
less stress – necked
aligning
region grows
Aligned
chain
crystals
breaking
(Secondary
Yield point)
Callister, 8e
47
Compression Testing
48
24
Compression Test Setup
Compression
test setup
Barreling effect in a
compression test…
©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e
49
Compression Test
Eng. Stress, eng F
Eng. Strain,
AO
h hO
hO
Where F = load (N, lb)
Ao = original area (mm2, in2)
eng = compressive stress (MPa, lb-ft)
h = specimen height (mm, in)
ho = initial specimen height (mm, in)
e = compressive eng. Strain (non-dimensional)
©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e
50
25
Stress‐Strain Curve in Compression
Shape of plastic
region is different
from tensile test
because cross section
increases
Calculated value of
engineering stress is
higher
©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e
51
Brittle Materials
Brittle materials break at tensile strength pt
YS = TS = breaking stress
Use bend test ‐ apply forces at three points and
measure deflection
Can also use abrasive test
Ability to withstand rubbing on specimen
sandpaper
Measure weight loss and convert to volume loss
52
26
3‐point Bending tests
Bend Test
fs
fs
3F f L
2bd 2
Ff L
R 3
Callister, 8e
53
Toughness
Energy absorbed due to fracture – fracture toughness
Charpy or Izod test
Tensile Toughness
ndt-ed.org
Callister, 8e
54
27
Hardness
H
F
indented area
Hardness: a measure of a material’s resistance to
localized plastic deformation
55
Hardness Tests
• Resistance to permanent indentation
‒ Good hardness generally means material is resistant to
scratching and wear
‒ Strong correlation between hardness & strength
Hardness tests commonly used to assess materials
because:
‒ Quick, convenient, inexpensive, non‐destructive
Most well‐known tests
‒ Rockwell, Brinell
56
28
Hardness Tests
Brinell Hardness Tests
(HB): 10 mm sphere of
steel or tungsten
carbide
Rockwell Hardness
Tests (HR): Diamond
cones or steel spheres
Knoop Microhardness
Tests (HK): Diamond
pyramid
Vickers Microhardness
Tests (HV)
©2010 John Wiley & Sons, Inc. M P Groover,
Fundamentals of Modern Manufacturing 4/e
57
Creep Test
Constant stress applied
< Yield stress
Primary Creep
‒ Decreasing strain rate
‒ Decreasing grain size
Secondary or
Steady‐State Creep
‒ Constant strain rate
‒ Thermal recovery
Tertiary Creep
‒ Increasing strain rate
‒ Necking, rupture
Callister, 8e
58
29
Fatigue Testing
Cyclic stresses applied like tension and
compression
Endurance ratio = endurance limit/TS
Fatigue Testing
59
30