Flight Operations All Weather Operations Guide Revision: 13 | Published: 01/03/2026 All Weather Operations Guide Disclaimer The purpose of this document and any associated attachments is to provide some guidance only on the topic. It should be viewed in conjunction with the appropriate approved publications. This document does not replace any official and more detailed information contained in the applicable operations manuals, Boeing FCOMS, Boeing FCTM or other official approved publications. Where any conflict arises between this guidance and the contents of official publications, then the information contained in the official publications takes precedence. This documentation was produced by the Ryanair ATO and is available for use in Ryanair DAC, Ryanair UK, Malta Air and Buzz No unauthorised copies or distribution allowed. © 2026 RYANAIR GROUP Prepared By Captain James Morrison – Training Compliance and Regulation SME Approved By Captain Ross Dickie – Chief Instructor Simulator Issued By Captain Paul Kelly – Head of Training Revision: 13 | Page | 2 All Weather Operations Guide DATE REVISION PAGE NOTES 01/10/2021 01/10/2021 2.0 2.0 ALL 16 01/10/2021 2.0 28 01/10/2021 2.0 32 01/10/2021 2.0 33 01/10/2021 06/04/2022 2.0 3.0 30/10/2022 30/10/2022 30/10/2022 30/10/2022 4.0 4.0 4.0 4.0 52 6, 14, 15, 28, 53 7 8 9 ALL 30/10/2022 4.0 10&11 30/10/2022 4.0 10&1&12 30/10/2022 30/10/2022 30/10/2022 4.0 4.0 4.0 13 14 16 30/10/2022 30/10/2022 4.0 4.0 18&19 27 30/10/2022 4.0 30-33 30/10/2022 4.0 47 30/10/2022 30/10/2022 4.0 4.0 52 55-58 UPDATED PUBLICATION FORMAT PRACTICE CAT II / III APPROACHES SECTION ADDED B737-8200 AUTOLAND OPT GUIDANCE ADDED GUIDANCE ADDED TO AUTOLAND PROCEDURES UPDATED REFERENCE TO FCOM FOR DUAL CHANNEL GO AROUND AUTOBRAKE GUIDANCE UPDATED UPDATED REFERENCES TO INCLUDE 8200 REVISION INTRODUCTION DEFINITIONS & LVTO CAT III OTS & LTS DEFINITIONS AND ABBREVIATIONS REMOVED CATII & CATIII TABLES & FLIGHT CREW APPROVALS COMMENCEMENT AND CONTINUATION OF APPROACH “APPROACH BAN” OCH & DH TABLE INTRODUCED PLANNING REQUIREMENTS FOR OPERATIONS AND SAFETY MARGINS FOR METEOROLOGICAL CONDITIONS & TABLE ADDITIONS FROM OMA 8.3.0.1.2 REMOVAL OF OLD TABLES AND INTRODUCTION OF GM1 SPA.LVO.100 (a) NEW TABLES OF “DOWNGRADED OR FAILED EQUIPMENT” & GM4 SPA.LVO.100(a) MINIMUMS TABLES FROM NAVBLUE CHARTS UPDATED REVISED PAGE FROM SP.16.19 UPDATED 8.4.5 OMA/ COMPETENCE OF FLIGHT CREW Revision: 13 | Page | 3 All Weather Operations Guide 31/08/2023 4.1 18/10/2023 5 20/11/2023 6 31/08/2024 31/08/2024 7 7 25/10/2024 8 04/11/2024 23/04/2025 9 10 16/07/2025 11 20/11/2025 28/02/2026 12 13 28/02/2026 13 34 REFERENCE TO APPROVED CATIII RUNWAY END LIST REMOVED 28 UPDATED AIRPORT TABLES (CORRECTIONS) 53 AUTOLAND WITH CROSSWIND CONDITIONS 39 UPDATED GUIDANCE ON VISUAL CUES 28,47 REPLACED NAVTECH REFERENCES AND SCREENSHOTS WITH JEPPESEN 9,10,31,47,56 200M RVR CHANGED TO 175M, WHERE APPLICABLE 9, 10, 30, 31 200M CORRECTION WITHIN TABLES 57 UPDATED MONITORED APPROACH APPLICABILITY 47 REFERENCES TO MIDPOINT RVR REMOVED. 21,22 UPDATE TO SECTION ON STOP BARS ALL NEW DOCUMENT TEMPLATE, TYPOGRAPHIC CORRECTIONS 35 CLARIFICATION AUTOLAND ALLOWED ON A CONTAMINATED RUNWAY Revision: 13 | Page | 4 All Weather Operations Guide Table of Contents Disclaimer ........................................................................................................................... 2 1. INTRODUCTION .............................................................................................................. 8 2. DEFINITIONS ................................................................................................................... 9 All Weather Operations (AWO) ...................................................................................... 9 Low Visibility Procedures (LVP) .................................................................................... 9 Low Visibility Take-Off (LVTO) ....................................................................................... 9 Flight Control System ..................................................................................................... 9 Fail Passive Automatic Landing System ...................................................................... 9 Decision Altitude/Height (DA/H) ................................................................................. 10 Minimum Descent Altitude/Height (MDA/H) ............................................................. 10 Stabilised Approach (SAp) ........................................................................................... 10 3. GENERAL ...................................................................................................................... 10 CATEGORY II ................................................................................................................. 10 CATEGORY III ................................................................................................................ 10 CAT III OBJECTIVE ........................................................................................................ 10 CONCEPT OF MINIMA .................................................................................................. 11 CATEGORIES ................................................................................................................. 11 CAT II Operation minima (Air Ops Part A 8.4.1.2/AMC 4 SPA.LVO.100) -..................................... 11 CAT III Operation minima (Air Ops Part 8.4.1.3/AMC 5 SPA.LVO.100) - ....................................... 12 WHY CATEGORY II/III?.................................................................................................. 12 RYANAIR APPROVALS (Air Ops Part A 8.4.5/Part SPA.LVO.120) ............................. 12 APPROACH BAN ........................................................................................................... 12 MINIMUM RVR FOR CONTINUATION OF APPROACH ............................................... 13 WHY HAVE THE APPROACH BAN AT ALL? ................................................................ 14 WHY DOES THE APPROACH BAN APPLY BEFORE 1000 ft ALL BUT NOT AFTER? 14 DECISION HEIGHT CONCEPT. ..................................................................................... 15 VISUAL REFERENCE ..................................................................................................... 15 EFFECT OF THE COCKPIT CUT-OFF ANGLE ON VISUAL REFERENCE. .................... 16 DRIFT ANGLE ................................................................................................................ 17 4. OPERATIONAL CONSIDERATIONS.............................................................................. 17 PLANNING AND SAFETY MARGINS FOR OPS/MET CONDITIONS: ......................... 17 DISPATCH PERFORMANCE ......................................................................................... 18 Revision: 13 | Page | 5 All Weather Operations Guide CHECK AIRCRAFT AUTOLAND STATUS ..................................................................... 19 Practice CAT II / III Approaches................................................................................... 20 5. TAXI .............................................................................................................................. 20 TAXIWAY LIGHTING ..................................................................................................... 21 COLOUR CODED TAXIWAY CENTRE LINE LIGHTING ................................................ 22 STOP BARS AND LEAD-ON LIGHTS ............................................................................ 23 PILOT LINE OF SIGHT AND STOP BAR POSITIONING ............................................... 23 TAXIWAY GUIDANCE SYSTEM .................................................................................... 25 TAXIWAY INTERSECTION LIGHTS .............................................................................. 25 REFLECTIVE TAXIWAY EDGE/CENTRELINE MARKERS/STUDS ............................... 25 SIGNS ............................................................................................................................. 25 RUNWAY TAXI-HOLDING POSITION (RTHP) SIGN FOR CAT II/III OPS..................... 25 6. RUNWAY LIGHTING ..................................................................................................... 28 CAUTION ZONE LIGHTING........................................................................................... 28 PRE-THRESHOLD LIGHTING ........................................................................................ 28 RUNWAY EXIT LIGHTING ............................................................................................. 30 STOPWAY LIGHTING .................................................................................................... 30 7. CLASSIFICATION OF LVTO OPERATIONS .................................................................. 32 GM1 SPA.LVO.100(a): ................................................................................................... 32 LVTO OPERATIONS IN AN RVR OF LESS THAN 400M .............................................. 32 VISUAL SEGMENT FOR TAKE-OFF .............................................................................. 33 GM2 SPA.LVO.100(a) .................................................................................................... 33 REJECTED TAKE-OFF ................................................................................................... 34 8. LVO APPROACH SET UP AND BRIEFING REQUIREMENTS ...................................... 34 ANNOUNCEMENT......................................................................................................... 34 WEATHER LIMITS ......................................................................................................... 35 CHECK FOR FAILURES OF GROUND BASED AIDS AND/OR EQUIPMENT: ............... 35 THE QRH LVO APPROACH AND LANDING CHECKLIST ............................................ 39 APPROACH CHARTS .................................................................................................... 39 CAT III SUITABLE AERODROMES (OMA 8.4.2 / AMC1 SPA.LVO.110) ...................... 39 9. APPROACH PROCEDURES AND CALLOUTS ............................................................. 40 PROCEDURE .................................................................................................................. 40 CALLOUTS ..................................................................................................................... 40 Revision: 13 | Page | 6 All Weather Operations Guide GO-AROUNDS ................................................................................................................ 44 10. THE VISUAL CUES ...................................................................................................... 45 VISUAL ILLUSIONS ....................................................................................................... 49 RAPID EXIT TAXIWAY INDICATOR LIGHTS: ................................................................ 50 11. AERODROME FACILITIES .......................................................................................... 50 PHYSICAL CHARACTERISTICS. .................................................................................. 51 OBSTACLE FREE ZONE (OFZ)...................................................................................... 51 AIRPORT VISUAL AIDS ................................................................................................. 51 NON-VISUAL AIDS ........................................................................................................ 52 EQUIPMENT .................................................................................................................. 52 ILS CRITICAL AREA ...................................................................................................... 52 ILS SENSITIVE AREAS .................................................................................................. 52 SECONDARY POWER SUPPLY ..................................................................................... 52 AERONAUTICAL INFORMATION SERVICES ............................................................... 52 TERRAIN PROFILE ........................................................................................................ 53 METEOROLOGICAL SERVICE....................................................................................... 53 TWO TYPES OF TRANSMISSOMETERS ...................................................................... 54 12. ENVIRONMENTAL FACTORS ..................................................................................... 55 THE CHARACTERISTICS OF FOG ................................................................................ 55 LOW LEVEL WINDSHEAR AND TURBULENCE............................................................ 56 CONDITIONS CONDUCIVE TO WINDSHEAR ............................................................... 56 THE RELATIONSHIP BETWEEN WINDSHEAR AND TURBULENCE ........................... 58 THE EFFECTS OF PRECIPITATION AND ICING .......................................................... 58 FLIGHT IN MODERATE TO HEAVY RAIN, HAIL, OR SLEET ........................................ 58 VISUAL ILLUSIONS FROM PRECIPITATION ................................................................ 59 LANDING ....................................................................................................................... 60 AUTOLAND WITH CROSSWIND CONDITIONS ........................................................... 60 SLIPPERY RUNWAY LANDING PERFORMANCE ........................................................ 60 ICE ACCRETION ............................................................................................................ 62 COMMANDER LVO QUALIFICATION ........................................................................... 63 FIRST OFFICER LVO QUALIFICATION.......................................................................... 64 APPENDIX – MONITORED APPROACHES ...................................................................... 65 Revision: 13 | Page | 7 All Weather Operations Guide 1. INTRODUCTION This document is issued to Ryanair Group Crew Members and covers the Low Visibility Procedures used by the Ryanair Group. It is to be used in conjunction with Air Operations Manual Part A and the Flight Crew Operations Manuals. It is not intended to replace those manuals. A thorough knowledge of these documents is a prerequisite to Low Visibility & All-Weather Operations. Where any conflict arises between the contents of the All-Weather Operations Guide and the contents of Operations Manual Part A, B737-800/8200 FCOMs 1 & 2, the contents of Air Operations Manual Part A and the FCOMs will take precedence. This document forms part of all initial LVO training programmes, it is designed as a self-study guide and must be studied by all students as part of the ground school syllabus. The document has the following objectives: ▪ To provide guidance to Ryanair Group flight crew in all aspects of All-Weather Operations (Low Visibility Operations). ▪ To emphasize the importance of the visual cues provided by the approach and runway lighting systems during Low Visibility Operations. ▪ To illustrate the runway and taxiway markings associated with Low Visibility Operations. ▪ To list the requirements for Ground Equipment and Aircraft Equipment together with the allowable deficiencies in such equipment. ▪ To emphasize the characteristics of fog, the effects of precipitation, ice accretion, low level wind shear and turbulence. This information applies to Ryanair B737 aircraft, which are equipped to allow CAT II & III operations. It is policy to maintain the fleet to CAT III status. Page | 8 All Weather Operations Guide Ryanair shall only conduct the following Low Visibility Operations (LVO) when approved by the IAA: • Low Visibility Take-off (LVTO) • Standard Category II (CAT II) • Standard Category III (CAT III) 2. DEFINITIONS The following are definitions of various aspects of low visibility operations and are in compliance with the recommendations of Part SPA.LVO, the updates on the Annex V (Subpart E: Low visibility Operations), and associated AMC material for CAT II and CAT III operations. All Weather Operations (AWO) Any Taxi, Takeoff or Landing operations in conditions where visual reference is limited by weather conditions. Low Visibility Procedures (LVP) Procedures applied at an aerodrome for the purpose of ensuring safe operations during Category II & III approaches and Low Visibility take-offs. Low Visibility Operations as dealt within the following paragraphs comprise: • Low Visibility Take-off Operations (LVTO) in visibility conditions of less than 550m RVR, and • Category II and III precision instrument approach and landing operations. Low Visibility Take-Off (LVTO) A take–off where the runway visual range (RVR) is less than 550m. Flight Control System A system, which includes an automatic landing system. Fail Passive Automatic Landing System A flight control system is fail passive if, in the event of a failure, there is no significant out-of-trim condition or deviation of flight path or attitude but the landing is not completed automatically. For a fail-passive automatic flight control system the pilot Revision: 13 | Page | 9 All Weather Operations Guide assumes control of the aeroplane after a failure. Note: Ryanair Aircraft are equipped with a Fail Passive Automatic Landing System. Decision Altitude/Height (DA/H) A specified altitude or height in the precision approach, at which, a missed approach must be initiated if the required visual reference to continue the approach has not been established. Decision altitude is referenced to MSL and the decision height is referenced to the threshold elevation. Minimum Descent Altitude/Height (MDA/H) A specified altitude or height in a non-precision approach or circling approach below which descent may not be made without visual reference. Stabilised Approach (SAp) An approach which is flown in a controlled and appropriate manner in terms of configuration, energy and control of the flight path from a pre-determined point or altitude/height down to a point 50 feet above the threshold or the point where the flare manoeuvre is initiated if higher. 3. GENERAL Ryanair require CAT II and CAT III approaches to be conducted to an AUTOLAND. CATEGORY II A category II approach is a precision instrument approach and landing with decision height lower than 200ft (60m) but not lower than 100ft (30m), and a runway visual range not less than 300m (1000ft). CATEGORY III A CAT III operation is a precision approach to lower than CAT II minima. A category III approach is a precision instrument approach and landing with a DH lower than 100ft (30m) or no DH, and an RVR less than 300m (1000ft) or no RVR limitation. Note: Ryanair is approved for CAT III (50 ft DH, 175m RVR where applicable). CAT III OBJECTIVE The main objective of CAT III operations is to provide a level of safety equivalent to other operations but in the most adverse weather conditions and associated visibility. Revision: 13 | Page | 10 All Weather Operations Guide In contrast to other operations, CAT III weather minima does not provide sufficient visual references to allow a manual landing to be made. The minima only permits the pilot to decide if the aircraft will land in the touchdown zone. Therefore, an automatic landing system is mandatory to perform Category III operations. Its reliability must be sufficient to control the aircraft to touchdown in CAT III operations. CONCEPT OF MINIMA Regulations often use the term minima. In fact, this term could refer to different concepts: 1. Airfield operating minima: established in accordance with the airport authority and published on approach charts. 2. Operator's minima: lowest minima that an operator is allowed to use at a specified airfield, following an approval from its operational authority. 3. Crew minima: lowest minima that the crew is authorized to operate, depending on the crew qualification. 4. Aircraft minima: lowest minima, which have been demonstrated during aircraft certification. These minima are indicated in the AFM. For all CAT II / CAT III operations, these minima consist of a DH and an RVR. CATEGORIES CAT II Operation minima (Air Ops Part A 8.4.1.2/AMC 4 SPA.LVO.100) Aircraft Categories DH (ft) Auto-coupled to below DH* A, B, C (RVR m) D (RVR m) 100 – 120 300 300/350* 121 – 140 141 – 199 400 450 400 450 *: An RVR of 300m may be used for a Category D aeroplane conducting an autoland. Note: HUD N/A RYR Note: CAT II instrument approach operations should only be conducted using a CAT II IAP (AMC2 SPA.LVO.110 (a)). Note: For CAT II instrument approach operations, a PA runway category II or category III should be used. The following visual aids should be available: Category II approach lights, standard runway markings and Category II runway lights. (AMC3 SPA.LVO.110) Revision: 13 | Page | 11 All Weather Operations Guide CAT III Operation minima (Air Ops Part 8.4.1.3/AMC 5 SPA.LVO.100) DH (ft) Roll-out control/guidance system RVR (m) 50-99 Not required 175* *: Ryanair is approved for CAT III (50 ft DH, 175 m RVR where applicable). Note: CAT III instrument approach operations should only be conducted using a CAT III IAP (AMC2 SPA.LVO.110 (b)) Note: For CAT III instrument approach operations, a PA runway category III should be used. The following visual aids should be available: Category III approach lights, standard runway markings and category III runway lights. (AMC3 SPA.LVO.110) WHY CATEGORY II/III? Category II/III operations allow the aircraft to be operated in limited visibility (normally associated with fog), and which is below Category I minimum. Convective weather is normally not a consideration with Category II/III approaches. Conditions are usually stable and therefore, the low visibility approach is considered safe. It is the policy of Ryanair to maintain the fleet to Category III status. RYANAIR APPROVALS (Air Ops Part A 8.4.5/Part SPA.LVO.120) The Ryanair approvals for Flight Crew operating on the B737 are as follows: Take-off: 125 m RVR Landing CAT II 100ft RA/300m RVR Landing CAT III 50ft RA/175m RVR* *where applicable Ryanair CAT III RVR is 175* APPROACH BAN APPLICATION OF RVR OR VIS REPORTS GM1 CAT.OP.MPA.305 (a) There is no prohibition on the commencement of an approach based on the reported RVR or VIS. The restriction in OMA 8.3.0.3.8.1(a) applies only if the RVR or VIS is reported and applies to the continuation of the approach past a point where the aircraft is 1000 ft above the aerodrome elevation or in the FAS, as applicable. (b) If a deterioration in the RVR or VIS is reported once the aircraft is below 1000 ft or in the FAS, as applicable, then there is no requirement for the approach to be Revision: 13 | Page | 12 All Weather Operations Guide discontinued. In this situation, the normal visual reference requirements would apply at the DA/H. (c) Where additional RVR information is provided (e.g. midpoint and stop end), this is advisory; such information may be useful to the pilot in order to determine whether there will be sufficient visual reference to control the aircraft during roll-out and taxi. For operations where the aircraft is controlled manually during roll-out, (AMC1 SPA.LVO.100(a)) provides an indication of the RVR that may be required to allow manual lateral control of the aircraft on the runway. MINIMUM RVR FOR CONTINUATION OF APPROACH AMC1 CAT.OP.MPA.305(a) (a) The touchdown RVR should be the controlling RVR. (b) If the touchdown RVR is not reported, then the midpoint RVR should be the controlling RVR. (c) Where the RVR is not available, CMV should be used except for the purpose of continuation of an approach in LVO in accordance with OMA 8.1.3.4.9 Table 16 CAT.OP.MPA.305 Commencement and continuation of approach “Approach Ban” (a) If the reported visibility (VIS) or controlling RVR for the runway to be used for landing is less than the applicable minimum, then an instrument approach operation shall not be continued: (1) or past a point at which the aeroplane is 1000 ft above the aerodrome elevation; (2) into the final approach segment (FAS) if the DH or MDH is higher than 1000 ft. (b) If the required visual reference is not established (OMA 8.3.0.3.10), then a missed approach shall be executed at or before the DA/H or the MDA/H. (c) If the required visual reference is not maintained after DA/H or MDA/H, then a go-around shall be executed promptly. (d) Notwithstanding point (a), in the case where no RVR is reported, and the reported VIS is less than the applicable minimum, but the converted meteorological visibility (CMV) is equal or greater than the applicable minimum, then the instrument approach can be continued to the DA/H or MDA/H. Revision: 13 | Page | 13 All Weather Operations Guide WHY HAVE THE APPROACH BAN AT ALL? There is considerable evidence from accidents, flight trials and simulations that in the highly dynamic situation around DH the pilot is not always able to make the correct decision in such marginal conditions. In order to determine the minimum RVR required for a particular DH, allowance is made for the time taken by the decision process, which should be completed when the DH is reached. In LVO conditions, during this decision process the pilot must assess the adequacy of the external references and also evaluate the flight path in relation to those references. The process is assumed to last some three seconds and therefore to start about 34ft prior to the DH. For there to be a high probability of obtaining adequate visual references, it has been established that the segment visible to the pilot should be of the order of 160m by the end of the decision process. This is equivalent to 3 seconds of ground speed. Obviously, this makes it difficult, if not impossible, to assess precisely what the visibility is. There is no time to start counting lights. The pilot also has little time to assess the trend in visibility as the aircraft progresses towards and along the runway. It is therefore considered prudent to prohibit the start (or continuation) of an approach if conditions at DH are likely to be unfavorable for a successful landing. WHY DOES THE APPROACH BAN APPLY BEFORE 1000 ft ALL BUT NOT AFTER? This is due to the fact that if the RVR was above minima when the aircraft was above 1000 ft AAL but has since deteriorated then there is likely a fluctuating RVR situation present. The Approach is allowed to continue, as there is still a reasonable chance of improvement in RVR. This also minimizes crew distraction caused by continual RVR readouts during the approach. According to EASA (CAT.OP.MPA.305), the pilot may commence an approach regardless of the reported visibility or RVR. However, the approach cannot be continued if the reported VIS/RVR is less than the applicable minimum: - below 1000ft AFE, or - into the final approach segment if the DA/MDA/MDH is located above 1000ft AFE. If after passing 1000ft, or in the FAS, the reported conditions fall below the applicable minimum, the approach can be continued down to DA/MDA/DH/MDH. The approach can be continued below DH/DA/MDA and landing can be completed if sufficient visual references are established and maintained for the type of approach. The touchdown zone RVR shall always be controlling when reported. Revision: 13 | Page | 14 All Weather Operations Guide DECISION HEIGHT CONCEPT. Decision height is a specified point in space at which a pilot must make an operational decision. The pilot must decide if the visual references are adequate to safely continue the approach:. • • If the visual references have not been established, a go-around must be executed. If the visual references have been established, the approach can be continued. However, the pilot may always decide to execute a go-around if sudden degradations in the visual references or a sudden flight path deviation occur. In Category II operations, DH is always limited to 100ft or Obstacle Clearance Height (OCH), whichever is higher. In Category III operations with DH, the DH is lower than 100ft (typically equal to 50ft for a fail-passive automatic landing system). The DH is measured by means of radio-altimeter. When necessary, the published DH takes into account the terrain profile before runway threshold. It is important to note that according to the: Air Operations ANNEX IV (Part-CAT) SUBPART B: OPERATING PROCEDURES: “Amongst other things the lowest DH for an instrument approach operation is determined by the system minima for the facility and the obstacle clearance height (OCH). The resulting DH determines the type of approach operation (type A or B). If the DH is 250 ft or more, it will be a type A approach operation; if the DH is less than 250 ft, it will be a type B approach operation.“ So, while ILS approaches to most runways may be conducted as type B approach operations, difficult obstacle situations, driving up the DH to 250 ft or higher, will result in type A approach operations. VISUAL REFERENCE Research using simulator and flight trials has shown that in general, visual contact needs to be established about 3 seconds above decision height to enable assessment of the external references and evaluation of the flight path in relation to those references. The change-over from flying on instruments to visual flying is the most difficult phase of the approach and needs good co-ordination and liaison between both Flight Crew members. For instrument approach operations Type A and CAT I instrument approach operations Type B, at least one of the visual references specified below should be distinctly visible and identifiable to the pilot at the MDA/H or the DA/H: Revision: 13 | Page | 15 All Weather Operations Guide (a) elements of the approach lighting system; (b) the threshold; (c) the threshold markings; (d) the threshold lights; (e) the threshold identification lights; (f) the visual glide path indicator; (g) the TDZ or TDZ markings; (h) the TDZ lights; (i) the runway edge lights; or (m) other visual references specified in the operations manual By definition, a go-around must be initiated at DH if the required visual reference to continue the approach has not been established. The visual reference must be adequate, i.e. must be of sufficient quality and duration to permit assessment of aircraft position and progress in relation to the desired flight path. Thus, the actual number of lights required to be visible at DH stems from the physiological requirements of being able to determine lateral level and cross-track position and velocity, rather than from any calculation of the number of lights which ought to be visible in a given RVR. Such calculation would be purely theoretical. The minimum RVR value specified in the previous table above should be achieved for all reporting points representative of the parts of the runway from the point at which the aircraft commences the take-off until the calculated accelerate-stop distance from that point EFFECT OF THE COCKPIT CUT-OFF ANGLE ON VISUAL REFERENCE. From an operational point of view, many variables are involved in determining the visual reference which will be achieved in practice. These include the Cockpit Cut-off Angle and related to it, the effect of body attitude, the approach light system, variations in the visual segment, and the time of day. The Cockpit Cut-off Angle is the angle between the horizontal and an inclined plane through the pilot’s eyes, below which the view ahead is obscured by the aircraft structure. It is measured with the aircraft in the landing attitude. The factors which affect cockpit cut-off angle for a given flap setting are: 1. Aircraft approach speed. 2. Glide path angle. 3. Pilot’s eye position. 4. Drift angle. ▪ During a normal approach on a 3° G/S for Flap 40 the B737 aircraft has a pitch attitude of approximately 0.0° and for Flap 30 it is approximately 1.0°. Revision: 13 | Page | 16 All Weather Operations Guide ▪ The number of approach lights visible from the visual segment will be reduced by the distance lost under the Cockpit Cut-off Angle. ▪ The distance lost under the Cockpit Cut-off Angle will decrease with aircraft height. It is very important to know that a small displacement from the correct eye position will significantly reduce the visual segment. For example, a displacement of only 1(one) cm below the correct eye position will reduce the visual segment by 10m. Prior to the approach, care should be taken to adjust the seat position to achieve the correct eye position. The pilots should have a clear understanding of the relationships between those points on the aircraft which constitute the datum for glide-path and radio altimeter inputs, and the geometry of the aircraft which dictates the Cockpit Cut-off Angle, thus determining the pilot’s visual segment. DRIFT ANGLE As the aircraft will automatically crab into wind whilst the APFDS is engaged in tracking the localizer, a crosswind from the left will impose a greater section of the glare-shield and radome into the Captain’s line of vision, thereby effectively increasing the cockpit cut- off angle, thereby reducing the visual segment. Conversely, a crosswind from the right will decrease the cut-off angle improving the visual segment as observed by the Captain. 4. OPERATIONAL CONSIDERATIONS PLANNING AND SAFETY MARGINS FOR OPS/MET CONDITIONS: • Check NOTAMS and MET forecasts for destination and alternate airports. An airport should only be selected as a take-off alternate aerodrome or destination aerodrome when the appropriate weather reports or forecasts or any combination thereof indicate that, during a period commencing 1 hour before and ending 1 hour after the estimated time of arrival at the airport, the weather conditions will be at or above the applicable landing minima with regard to the RVR/visibility and also, in the case of a type A or a circling approach, the ceiling at or above the MDH. Wind limitations should also be considered. • There shall be an adequate airport along the route, no further than the distance flown in still air, in 60 min at the one engine inoperative cruise speed. • The distance travelled in 1 hour at the one engine inoperative cruise speed is 427nm for the B737-800 or 416nm for the B737-700/8200. • Ryanair shall specify any required alternate aerodromes in the operational flight plan. • At least two destination alternate aerodromes shall be selected, when: Revision: 13 | Page | 17 All Weather Operations Guide o The appropriate weather forecasts for the destination aerodrome, or any combination thereof, indicate that during a period commencing one hour before and ending one hour after the estimated time of arrival the weather conditions will be below the applicable planning minima, or o No meteorological information is available for the destination aerodrome. For the selected en-route or destination alternate the appropriate weather reports or forecasts or any combination thereof indicate that, during the period commencing 1 hour before and ending 1 hour after the expected time of arrival at the alternate, the weather conditions will be at or above the planning minima as follows, taking into consideration any limitations related to OEI ops: ▪ ▪ ▪ ▪ Consider requirements for extra fuel to be loaded. Allow for delays at the destination during CAT II / III LVP’s due to the potential adjustments to separation requirements. A backlog will exist even after weather improvements. Low visibility, thunderstorms etc., are events, which clearly do not provide reasonable certainty of landing, and generally there will be extra fuel uplifted to address these conditions. There is a balance between the cost of holding for a lengthy period at destination and the cost of a diversion. Confirm Flight Crew qualification. A take-off alternate shall be selected and specified in the operational flight plan if the weather conditions at the aerodrome of departure are at or below Ryanair’s established aerodrome landing minima for that operation or it would not be possible to return to the aerodrome of departure for other reasons. The take-off alternate must be located within 427 NM for the B737-800 or 416 NM for the B737-700/8200 (OEI specs). For low visibility operations as stated in 5.1.3 OMA, the aerodrome must be approved and low visibility procedures established. If the term LVP is not used then equivalent procedures must be established. DISPATCH PERFORMANCE B737-800/B737-8200 140m is the Boeing “advisory” corrections for Autoland with Flaps 40. Autoland correction for Flaps 30 is 185m. Further reduction for contaminated not required. Autoland increment is to air distance only. Revision: 13 | Page | 18 All Weather Operations Guide B737-700 135m is the Boeing “advisory” corrections For Autoland with Flaps 40. Autoland correction for Flaps 30 is 185m. Further reduction for contaminated not required. Autoland increment is to air distance only. CHECK AIRCRAFT AUTOLAND STATUS The following sources are available to determine the aircraft AUTOLAND status: 1. In the EFL App under AIRCRAFT STATUS. 2. On the Aircraft: ▪ In the Techlog under ‘Notice to Crew’. ▪ Placards on the front cover of the Techlog and on the centre pedestal (Green/white stripes indicate aircraft status is CAT III. Blue/white stripes indicate CAT I only status). ▪ In addition, the MEL/QRH includes a list of the minimum equipment that has to be serviceable at the commencement of a Low Visibility Take-off or LVO approach. Note: MEL reference to CAT III implies AUTOLAND. Note: The following information is available in the AFM: “The Autopilot System has been shown to meet the applicable airworthiness performance and integrity criteria established for a fail passive system to comply with JAR-AWO Subparts 1, 2, and 3 for automatic approach and landing with the following equipment operative and FLARE arm annunciated:” The following equipment must be operative. ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Dual Channel Autopilot Low Range Radio Altimeter and display for each Pilot Decision Height (DH) Display for each Pilot Two Digital Air Data Computer Systems Windshield Wipers for each Pilot ILS Receiver and display for each Pilot Flight Mode Annunciator for each Pilot Two ADIRU's (associated with the engaged autopilots) in NAV mode Dual Hydraulic Systems Two sources of electrical power (The APU generator may be used as an independent power source) Both Engines Operating Revision: 13 | Page | 19 All Weather Operations Guide Practice CAT II / III Approaches Flight crews are encouraged to inform ATC of their intent to conduct an autoland approach. Flight crews should exercise caution during all autoland procedures. Preceding arriving or departing aircraft may cause deviations to the ILS signal; such deviations may be present during CAT I or better weather conditions even when the ILS critical area is protected. OMA 8.4.4 “Practice CAT II / III approaches are permitted to unprotected runways, with visibility 1,500 m or greater and ceiling 500 ft or higher, including at night. Verify all Landing Distance Required for all practice autolands, During a practice approach, system malfunction in itself does not require a Go-Around. In a practice CAT II / III approach, the captain may decide to take over manually and land provided the approach can be continued safely.” 5. TAXI Low Visibility taxi is one of the most demanding phases of flight. A good briefing for the taxi-out or taxi-in phase is extremely important and should be completed during RIBETS or DALTA. TEM considerations must be discussed. NO PAPERWORK WHATSOEVER SHOULD BE COMPLETED DURING TAXI-OUT OR TAXI-IN, IN LVO’S. F/O must follow taxi route as per EFB chart. If EFB is not available, the taxi chart must be clipped onto the control column during all ground OPS in LVP’s. It is also reminded that this is a failure items during the Line check procedure, to emphasize the importance of active taxi monitoring by the F/O. The Taxi phase of operations shall be considered a ‘Critical Phase of Flight’. A sterile cockpit is mandatory and only essential safety PA’s are allowed. In low visibility, the Captain will normally follow the green lights on the taxi routing. If this lighting is not available, confirm taxiways with airport signage and HDG on flight instruments. Bear in mind that in poor visibility, e.g. 100m RVR, one might expect to see bright lights 100m away, but not unlit or poorly lit obstacles such as aircraft tails or wingtips. From certain angles their navigation lights are not readily discernible and the greatest distance from which a white painted aircraft may be visible in 100m RVR may be less than 75m. Movement rates will be low in these conditions, therefore taxi slowly. Use of Ground Movement radar, flight instruments, and an aerodrome chart will help to assess the aircraft position and help in anticipating bends in the taxiways. Centre line light spacing may be reduced on bends and caution should be exercised when coming out of the bend where the lighting reverts to normal. Be careful not to pass the Cat II & Cat III holding point. Revision: 13 | Page | 20 All Weather Operations Guide Green taxiways centre line lights may be illuminated beyond the CAT II / III holding point if it does not coincide with a taxiway stop-bar, or if a preceding aircraft is just lining up. It is most important for pilots to be particularly careful at all times, NOT to inadvertently stray on to operating runways, but particularly when visibility on the aerodrome is impaired by fog or low cloud. Discuss and review any Runway Incursion Hotspots on Charts. Great care must be taken to read, callout and interpret correctly all pertinent signs to verify position. Particular attention should be focused on marker boards that are placed to identify taxiways, intersections and approaches to runways (active or non-active and holding points), prior to entering the active runway. Very careful perusal of the aerodrome surface charts and maintaining a watchful lookout for taxiway identification and other marker boards is vital if incursions on to an active runway are to be avoided. If there is any doubt whatsoever about the position of the aircraft whilst taxiing before takeoff or after landing, STOP and inform ATC immediately, For their information. Ask for guidance in standard English ATC phraseology. ATC can then immediately give the necessary urgent instructions to aircraft about to depart or land; to discontinue, takeoff or approach as applicable, before taxiing assistance and guidance is offered to the ‘lost’ crew. If you inadvertently enter a runway, immediately notify ATC (an ASR for runway incursion is required). If visibility enables you to safely vacate a runway, then do so, and advise ATC. If in LVPs, and it is not safe to vacate a runway, include this in your notification to ATC. TAXIWAY LIGHTING At those aerodromes equipped for low visibility operations, taxiways are equipped with green centre line lighting otherwise blue edge lighting is provided, as shown in Figure 1.0. Where green centre line lighting is provided, blue taxiway edge lighting may also be installed as additional guidance on sections of taxiway that are difficult to negotiate. Green taxiway centre line lighting may be provided on the runway prior to an exit taxiway in order to give leadoff guidance. The edge of aprons, turning and holding areas are normally marked by blue lighting. NOTE 1. Where centre line lighting is installed on a taxiway leading onto a runway, the taxiway lighting is curved onto the near side of the runway centre line and pilots should make an appropriate allowance for any loss of Runway Declared Distance incurred in following the 'lead-on' lighting whilst lining up for take-off. Revision: 13 | Page | 21 All Weather Operations Guide NOTE 2. Taxiway centre lines are intended to provide safe clearance between the largest aircraft that the taxiway is designed to accommodate and fixed objects such as buildings, aircraft stands etc., provided that the pilot of the taxiing aircraft keeps the 'Cockpit' of the aircraft on the centre line and that aircraft on stands are properly parked. Taxi Holding Positions are normally located so as to ensure clearance between an aircraft holding and any aircraft passing in front of the holding aircraft, provided that the holding aircraft is properly positioned behind the holding position. Clearance to the rear of any holding aircraft cannot be guaranteed. When following a taxiway route, pilots and persons towing aircraft are expected to keep a good lookout, consistent with the prevailing visibility and are responsible for taking all possible measures to avoid a collision with another aircraft or a vehicle. Figure 1.0 Taxiway Lighting COLOUR CODED TAXIWAY CENTRE LINE LIGHTING Where part of a taxiway equipped with centre line lighting lies within the ILS Sensitive Revision: 13 | Page | 22 All Weather Operations Guide Area or is sufficiently close to a runway that aircraft on that part of the taxiway would present an obstruction to aircraft landing or taking-off, that part of the taxiway will be identified by alternate green and yellow centre line lights, as shown at Figure 1.0. Pilots should avoid stopping with any part of their aircraft in such areas. STOP BARS AND LEAD-ON LIGHTS Lighted Stop Bars and Lead-on Lights are provided at those aerodromes authorised for low visibility operations. A Stop Bar consists of a row of lights spaced equally across the taxiway normally at right angles to the centre line and showing red towards an approaching aircraft when lit. Stop Bars are normally installed in association with green Lead-on Lights, which form part of the taxiway centre line lighting beyond the Stop Bar. The Lead-on Lights are interlinked with the Stop Bar so that when the Stop Bar is 'on' the green centre line beyond the Stop Bar is 'off' and vice versa, as shown in Figure 1.0. In this way, the Stop Bar and associated Lead-on Lights act in the same sense as traffic lights; therefore: pilots must not taxi an aircraft across a lit Stop Bar. RED means STOP. Stop bars are provided at entrances to runways, e.g. runway holding positions, and may also be provided at taxiway intersections and at other locations. NOTE: At some aerodromes where, for example, a Stop Bar is located on or close to a bend in the taxiway route, additional elevated red lights may be installed outboard of each taxiway edge as shown at Figure 1.0, in order to provide maximum advanced warning of the Stop Bar location. PILOT LINE OF SIGHT AND STOP BAR POSITIONING Due to the pilot line of vision from the flightdeck, crews will instinctively stop so they can see the stop bar lights ahead to avoid runway incursion. Be aware that in doing so you will be approximately 15m back from where you are designed to stop potentially infringing on any taxiways behind you. If you are taxiing behind an aircraft that has stopped in this position, taxi with caution as you may not have sufficient wingtip clearance. When approaching an illuminated stop bar with the intentions to stop and hold, the Captain should taxi forward until the red stop bar disappears out of sight under the Revision: 13 | Page | 23 All Weather Operations Guide glareshield. (see view point below) Pilots should note the importance of correct seating and optimum eye position as detailed in FCTM. Pilots should always be in a position to ensure the red stop bar lights are in their field of view through the DV window as depicted in viewpoints below. Note: The pilot position is 1.6m forward of the nose wheel. Before crossing stop bars pilots should: 1. have an ATC clearance to proceed beyond any holding position/stop bar, in particular those protecting runways. 2. challenge ATC if they are cleared to cross an illuminated stop bar - RED means STOP 3. confirm that the stop bars are switched OFF (except in the exceptional circumstances described in ICAO Doc 9870, Appendix B which states “if stop bars, lights or controls are reported to be unserviceable, contingency measures, such as using follow-me vehicles, are in force...”) Revision: 13 | Page | 24 All Weather Operations Guide TAXIWAY GUIDANCE SYSTEM At aerodromes where Category II and III operations take place or where ground movement requirements are complex, a surface movement guidance and control system (SMGCS) may be installed in order to regulate traffic. The system operates by selective switching of the taxiway centre line lighting so that individual sections or routes, each terminating at a lit Stop Bar, are illuminated in order to show the way ahead. The Stop Bar is extinguished as the next section of taxiway centre line lighting is selected. TAXIWAY INTERSECTION LIGHTS At some aerodromes where multiple intersecting taxiways are not provided with selective route guidance, Taxiway Intersection Lights may be provided. These consist of a row of at least 3 steady yellow lights disposed symmetrically about the taxiway centre line. Pilots approaching an intersection where these lights are displayed should give way to crossing traffic unless otherwise instructed by air traffic control (ATC) REFLECTIVE TAXIWAY EDGE/CENTRELINE MARKERS/STUDS On taxiways that are used infrequently, reflective edge markers or centre line studs may be used instead of taxiway lighting. Edge markers are blue and centre line studs are green. SIGNS The signs located on an aerodrome when used in conjunction with an aerodrome chart are intended to simplify surface movement guidance and control procedures, particularly in conditions of low visibility. Signs are divided into two categories, namely Mandatory Signs and Information Signs. Mandatory Signs consist of Runway Taxi-Holding Position (RTHP) signs, Intermediate Taxi-Holding Position (ITHP) signs and No Entry signs and display white characters on a red background as illustrated at Figure 1.2 and 1.3. RTHP and ITHP signs are located alongside the appropriate surface marking and identify the holding position as well as indicate the direction in which the holding instruction applies. Pilots should not proceed beyond a Mandatory Sign unless directed to do so by ATC. RUNWAY TAXI-HOLDING POSITION (RTHP) SIGN FOR CAT II/III OPS At aerodromes equipped for Category II and III ILS approaches, RTHP signs are annotated CAT II, CAT III or CAT II / III as appropriate, in the manner illustrated in Figures 1.2 and 1.3. However, because of the need to provide greater protection to Category II and III ILS systems, the RTHPs associated with these procedures are set farther back from the runway than those associated with visual or Category I operations; where this distance is such that it would hinder the expeditious flow of traffic when Category II or III procedures are not in force, a visual RTHP may be established in addition, closer to the runway, in the manner illustrated at Figure 1.3 (e) Revision: 13 | Page | 25 All Weather Operations Guide and (f). Exceptionally, CAT I RTHPs may be established in this manner, as illustrated at Figure 1.2 (b), for the same reason. Figure 1.2 Typical Runway Taxi-Holding Position Signs Revision: 13 | Page | 26 All Weather Operations Guide Note: 1: The signs at (i) are used where the taxiway normally serves only one runway direction. The signs at (ii) are used where the taxiway normally serves both runway directions. Figure 1.3 Typical Runway Position Signs and Associated Taxiway Markings Revision: 13 | Page | 27 All Weather Operations Guide The diagrams in Figure 1.3 illustrate typical signs associated with various Runway Taxi-holding positions on Taxiway ‘A’ leading to the threshold of Runway 27 and on Taxiway ‘D’ leading to an intermediate taxiway entrance to Runway 09-27. NOTE: The signs at intermediate taxiway entrances as shown at Figure 1.3 (b) and (d) show the runway designation in both directions; a left turn is required to reach the threshold of Runway 09 and a right turn to reach the threshold of Runway 27. 6. RUNWAY LIGHTING All runways licensed for night use have Edge, Threshold and End Lighting. Centre line and Touchdown Zone Lighting is provided as additional guidance in support of low visibility operations. Runway Edge Lighting is located along the edges of the area declared for use as the runway delineated by white edge markings and may be provided either by elevated or by flush fitting lamp fixtures. At some aerodromes where elevated runway edge lights are employed, the light fixtures may be located on the grass shoulder just beyond the declared runway width. Portable battery-operated lights may be used in place of fixed lamp fittings at small aerodromes where limited operations take place at night. Runway Edge Lighting is white except in the following instances: CAUTION ZONE LIGHTING On ILS equipped runways without centre line lighting, yellow edge lighting as illustrated at Figure 1.5 (B), is installed on the upwind 600 m or one third of the lighted runway length available, whichever is the less. The yellow 'caution zone' so formed gives a visual warning of the approaching runway end. PRE-THRESHOLD LIGHTING Where a landing threshold is displaced, but the pre-threshold area is available for the take-off run, the lights between the beginning of the runway pavement and the displaced threshold show red from the approach, as illustrated at Figure 1.4. Pilots taking off in such a situation would see red edge lights up to the green threshold then white edge lights beyond. Where a starter extension, narrower than its associated runway is provided, blue edge lighting is normally used to mark the edges, as illustrated at Figure 1.4. In most European states the edge of the starter extensions are marked with solid white lines the same as runway edges however some states have used dashed lines to define runway starter extensions, crew should remain vigilant to the possibility of confusing dashed edge markings with the centerline marking in states that use this system. E.g. Italy. Revision: 13 | Page | 28 All Weather Operations Guide Brescia RWY 32 Brussels Airport RWY 19/25 When departing from Italian destination especially when lining up on a starter extension ensure correct runway alignment, remember if you are unsure STOP and check. Wrong alignment with the runway edge rather than runway centre line. Follow procedures, Anticipate, take your time, tune the ILS for departure and set the CRS selectors to the active runway. Revision: 13 | Page | 29 All Weather Operations Guide RUNWAY EXIT LIGHTING One or two omni-directional blue lights may replace or supplement the edge lights in order to indicate an exit taxiway. STOPWAY LIGHTING Where stopway is provided at the end of a runway, the declared stopway is delineated by red edge and end lighting as illustrated in Figure 1.4 showing ONLY in the direction of landing. A stopway is provided for emergency use only and is not normally suitable for routine use. Revision: 13 | Page | 30 All Weather Operations Guide Figure 1.4 Runway Edge, Threshold and Edge Lighting NOTE: When lining up in reduced visibility use extreme care not to mistake Runway Edge Lights for Runway Centerline Lights, as they may both be white. Ensure the aircraft line’s up with the centerline lights. Revision: 13 | Page | 31 All Weather Operations Guide 7. CLASSIFICATION OF LVTO OPERATIONS GM1 SPA.LVO.100(a): Take-off operations are classified as ‘normal take-off operations’ with an RVR at or above 550m and ‘LVTO operations’ with an RVR below 550m. Only LVTO operations in an RVR of less than 400m require a specific approval. LVTO OPERATIONS IN AN RVR OF LESS THAN 400M AMC1 SPA.LVO.100(a) Low-visibility operations (a) Required RVR (1) For multi-engined aeroplanes which, in the event of a critical engine failure at any point during take-off, can either stop or continue the take-off to a height of 1500 ft above the aerodrome while clearing obstacles by the required margins, the criteria in Table 2 should apply: LVTO operations — RVR versus facilities (OMA Table 2) Minimum RVR (m) Facilities 300m (day) Centre line markings; and Runway edge lights. 300m (night) Centre line markings; and Runway edge lights; and Runway end lights or centre line lights. 150m 125m Centre line markings; and Runway end lights; and Runway edge lights; and Runway centre line lights. Centre line markings; and Runway end lights; and Runway edge lights (spaced 60m or less); and Runway centre line lights (spaced 15m or less). (b) The reported RVR value representative of the initial part of the take-off run can be replaced by pilot assessment. (c) The minimum RVR value specified in Table 2 should be achieved for all reporting points representative of the parts of the runway from the point at which the aircraft commences the take-off until the calculated accelerate-stop distance from that point. Revision: 13 | Page | 32 All Weather Operations Guide VISUAL SEGMENT FOR TAKE-OFF GM2 SPA.LVO.100(a) Low-visibility operations and operations with operational credits The value of 125m RVR for take-off with 15m centre line light spacing has been selected because flight deck geometry means that this will provide at least a 90m visual segment for the large majority of aircraft types. In a 90m visual segment the pilot is expected to be able to see six centre line light intervals (seven centre line lights) at 15m spacing once lined up on the runway centre line. The 125m approval is listed in the AOC. When assessing RVR during LVO Takeoffs it is important to be familiar with the correct lighting systems associated with the runway in use. This information is normally found on the aerodrome charts. For example, below shows DUB 10 R&L / 28 R&L with centerline lighting spacing at 15m intervals. Prior to entering the active runway, ILS, if available shall be tuned and runway course selected to confirm you are on correct runway. Revision: 13 | Page | 33 All Weather Operations Guide NOTE: At certain aerodromes with displaced thresholds, the supplementary approach lighting is insert into the runway and in certain weather and ambient light conditions the centre line barrettes, at the higher intensity settings, can partially obscure the runway centre line lighting to pilots lining up for departure. Pilots experiencing problems of this nature should ask for the intensity of the supplementary lighting to be adjusted or extinguished. REJECTED TAKE-OFF If it is necessary to reject the takeoff and visibility is very limited, directional control with reference to the centre line lights may become more difficult as speed is reduced. Apply maximum manual braking or verify operation of RTO autobrakes to ensure the aircraft stops before the end of the runway. As soon as the centre line lights change to alternate red and white there is 900m of runway left. When only 300m of runway remains, the centerline changes to continuous red lights. Bear in mind that the aircraft is not visible from the tower in LVTO. Not all airports have ground radar. Therefore, in case of rejected takeoff, it is very important to report to the tower as soon as the parking brake has been set and flaps 40 are selected. With very limited visibility, directional control with reference to the centre line lights is difficult, particularly with the asymmetric moment of an engine failure, and loss of the centre line lights streaming, as IAS reduces. This demands early corrections to maintain the centre line. 8. LVO APPROACH SET UP AND BRIEFING REQUIREMENTS ▪ ▪ Check Aircraft CAT III status. Both pilots must be CAT III qualified. If possible, a handover to the F/O should be made at the latest 100nm prior to TOD. A monitored auto-coupled shall be approach flown and briefed by the F/O. In addition to the usual approach setup and briefing using DALTA, crews shall take note of the following; ANNOUNCEMENT ▪ Airports approved for CATII / III will put into force “low visibility procedures” (LVPs) when weather conditions warrant. This will normally be announced on the ATIS or by ATC. ▪ Specific holding points for taxiing aircraft are enforced and illuminated to ensure obstruction and interference from obstacles is minimized. Separation from arriving and departing aircraft is increased to avoid interference. ▪ Refer to the chart for airport specific low visibility departure or arrival procedures. Revision: 13 | Page | 34 All Weather Operations Guide WEATHER LIMITS ▪ Headwind max 25kts, x-wind max 20kts, max 10kts tailwind. ▪ Turbulence no more than light to moderate. ▪ Precipitation no more than moderate. ▪ No windshear reported. ▪ RWYCC 2 or greater. Note: B737-800/B737-8200 If autoland performance data is not available, use Flap 30 or Flap 40, then increase Reference Distance by 140m for Flap 40 and 185m for Flap 30. B737-700 In Flight Performance, Use Flap 30 or Flap 40, then increase Reference Distance by 135m for Flap 40 and 185m for Flap 30. CHECK FOR FAILURES OF GROUND BASED AIDS AND/OR EQUIPMENT: INSTRUMENT APPROACH OPERATIONS IN LOW-VISIBILITY CONDITIONS — EFFECT ON LANDING MINIMA OF TEMPORARILY FAILED OR DOWNGRADED EQUIPMENT FOR APPROACH OPERATIONS WITH A DH BELOW 200 ft GM4 SPA.LVO.100(b), AMC3 SPA.LVO.100(b) Low-visibility operations The instructions for the effect on landing minima of temporarily failed or downgraded equipment are intended For use both before flight and during flight. It is, however, not expected that the pilot-in-command/commander would consult such instructions after passing 1000 ft above the aerodrome. If failures of ground aids are announced at such a late stage, the approach could be continued at the pilot-in-command/commander’s discretion. If failures are announced before such a late stage in the approach, their effect on the approach should be considered as described in Table 6, and the approach may have to be abandoned. (a) Only those facilities mentioned in Table 6 should be acceptable to be used to determine the effect of temporarily failed of downgraded equipment on the required RVR For CAT II / III approach operations. (b) The following conditions should be applied to Table 6 below: (1) multiple failures of runway/FATO lights other than those indicated in Table 6 are not acceptable; Revision: 13 | Page | 35 All Weather Operations Guide (2) failures of approach and runway/FATO lights are acceptable at the same time, and the most demanding consequence should be applied; (3) For approach operations with a DH below 200 ft, a combination of deficiencies in runway/FATO lights and RVR assessment equipment are not permitted; and (4) failures other than ILS, GLS and MLS affect the RVR only and not the DH. Failed or downgraded equipment – effect on landing minima CAT II / III operations (OMA Table 6) Navaid stand-by transmitter Outer marker (ILS) CAT III no DH CAT III DH < 50 ft Not allowed RVR 200 m No effect No effect No effect if replaced by RNAV (GNSS) information or the outer marker. RVR assessment systems At least one RVR value to be available on the aerodrome Approach lights No effect Approach lights except the last 210m On runways equipped with two or more RVR assessment units, one may be inoperative Not allowed for operations with DH > 50 ft No effect No effect Standby power For approach lights No effect Day: RVR 550m Day: RVR 550m Night: RVR 550m Night: RVR 550m No effect Not allowed Edge lights No effect Day: no effect Day: no effect Night: RVR 550 Night: RVR 550m m Threshold lights No effect No effect Not allowed Not allowed Approach lights except the last 420m Standby power For runway lights with 1-second switchover time CAT II No effect if the required height versus glide path can be checked using other means, e.g. DME fix Middle marker (ILS) DME CAT III DH >= 50 ft Day: no effect Day: no effect Night: not allowed Day: no effect Revision: 13 | Page | 36 All Weather Operations Guide Night: RVR 550m Runway end lights No effect if centre line lights are serviceable Day: RVR 300m Day: RVR 200m Centre line lights Night: not allowed Centre line lights spacing increased to 30m TDZ lights Night: not allowed Not allowed Day: RVR 350m Night: RVR 550m Night: RVR 400m (400m with HUD or Autoland) RVR 150m No effect No effect Day: RVR 300m Day: RVR 175m Night: RVR Night: RVR 550m, 350m with HUD 300m or Autoland Taxiway light system No effect *175m only applicable where applicable. Note: When the airfield anemometer is failed or downgraded, the Commander shall: • • • • Assess whether to land. Decide which pilot conducts the landing. PM monitors wind presentation on the ND. PF/PM assesses windsock information (other ground source). Captain only landing at night For operations to actual RVR values less than 300m, in the event of an autopilot failure at or below DH a missed approach shall be executed. EFFECT ON LANDING MINIMA OF TEMPORARILY FAILED OR DOWNGRADED GROUND EQUIPMENT AMC11 CAT.OP.MPA.110 Aerodrome operating minima These instructions are intended for use both before and during flight. It is, however, not expected that the commander would consult such instructions after passing 1000 ft above the aerodrome. If failures of ground aids are announced at such a late stage, the approach could be continued at the commander’s discretion. If failures are announced before such a late stage in the approach, their effect on the approach should be considered as described in Table 17, and the approach may have to be abandoned. Revision: 13 | Page | 37 All Weather Operations Guide Failed or downgraded equipment — Effect on Landing Minima Operations without LVO approval (OMA Table 17) Effect on landing minima Failed or downgraded equipment Type B Navaid stand-by transmitter Type A No effect APV —not applicable Outer marker (ILS only) Middle marker (ILS only) Not allowed except if the required height versus glide path can be checked using other means, e.g. DME fix No effect NPA with final approach fix (FAF): no effect unless used as FAF If the FAF cannot be identified (e.g. no method available for timing of descent), NPA cannot be conducted No effect unless used as MAPt RVR assessment systems No effect Approach lights Minima as for NALS Approach lights except the last 210m Minima as for BALS Approach lights except the last 420m Minima as for IALS Standby power For approach lights No effect Edge lights, threshold lights and runway end lights Day: no effect; Night: not allowed Centre line lights Centre line lights spacing increased to 30m TDZ lights Taxiway lighting system No effect if flight director (F/D), HUDLS or autoland; otherwise RVR 750m No effect No effect No effect if F/D, HUDLS or autoland; otherwise RVR 750m No effect No effect Conditions applicable to Table 17: • multiple failures of runway/FATO lights other than those indicated in Table 17 should not be acceptable; • failures of approach and runway/FATO lights are acceptable at the same time, and the most demanding consequence should be applied; and • failures other than ILS, GLS, MLS affect the RVR only and not the DH. Revision: 13 | Page | 38 All Weather Operations Guide MINIMUMS ▪ Radio minimums shall set to the required DH. ▪ The EGPWS auto-callouts will occur at “plus hundred” and “minimums”. Callouts are based on height set on the Captain's Radio minimums selector only. ▪ When descending below the selected minimums the Radio Altimeter (RA) display flashes for 3 seconds. ▪ A failure of the RA system is indicated by removal of the respective height information and replaced with the letters RA within an amber box. THE QRH LVO APPROACH AND LANDING CHECKLIST The QRH LVO Approach and Landing checklist must be used as a basis for every CAT II / CAT III approach briefing. APPROACH CHARTS CAT II / CAT III minima are published on the bottom of the appropriate ILS plate for the runway. CAT III SUITABLE AERODROMES (OMA 8.4.2 / AMC1 SPA.LVO.110) The Performance Department maintains a register of aerodromes and runway ends assessed and approved for Low Visibility Operations. Any approved aerodrome as listed in OMC Appendix A – Approved Aerodrome List (DOCUNET – FLIGHT SUPPLEMENTS) with an LVO landing procedure that has not passed an assessment will be notified to crew by COMPANY NOTAM or Airfield Brief (AFB) as not authorised (example below). CO837/22 COMPANY NOTAM ***** OPERATIONAL ***** LIEGE EBLG/LGG LVO LANDING USE OF APPROACH MINIMA BELOW CAT I IS NOT AUTHORISED ON RWY 04R UFN PERFORMANCE 30OCT22 INFORMING THE NO.1 Prior to conducting an autoland the captain must inform the No.1. This will allow the No.1 to instruct passengers to switch off electronic devices. SEP 2.24.1 refers: Under certain circumstances where the auto-landing system is going to be used all electronic devices must be switched off for approach and landing. The Captain will inform the No.1 and the No.1 will make the following PA: Revision: 13 | Page | 39 All Weather Operations Guide “Ladies and gentlemen, the Captain has informed us that on this occasion all electronic devices must be completely switched off for the landing, this includes devices in Airplane or Flight mode. Thank you” 9. APPROACH PROCEDURES AND CALLOUTS Approaching an LVP declared destination, inform ATC that a CAT II / III approach will be made, thus ensuring priority over non-CAT II / III aircraft in the holding stack. On first contact with the Approach controller request a Cat II / III approach with a 10nm final. Ensure Cabin secure has been received prior to commencing the final approach. When the RVR is just below minimum, and it is necessary to decide whether to remain in the hold for an improvement or to divert, keep in mind that the VOLMET and ATIS RVRs may not be the same as the current RVR. If workload permits, monitor the Tower frequency to get the latest RVR. When the visibility is rapidly improving, the low visibility safeguarding procedures may be abandoned by ATC in order to increase the traffic flow. If this should occur after the aircraft has left the hold, a call to the Tower will enable the controller to advise that appropriate protection is no longer available. If that is the case it is then the pilot’s responsibility to check that the sensitive area is clear of other aircraft. PROCEDURE ▪ F/O (RHS) shall always be PF until minimums. ▪ At or before minimums the Captain becomes PF if he/she announces that the decision is to continue. ▪ If there are no adequate visual cues at minimums, the F/O remains PF and executes the go around. ▪ F/O must stay on instruments throughout the approach. CALLOUTS Normal CAT I callouts with the following differences/additions: ▪ When cleared for the approach the F/O shall engage approach mode followed by the second A/P and call “Command A and B” ▪ When using the autothrottle position the command speed to VREF + 5. Sufficient wind and gust protection is available with the autothrottle connected because the autothrottle is designed to adjust thrust rapidly when the airspeed drops below command speed while reducing thrust slowly when the airspeed exceeds command speed. ▪ At 5NM the Gear and Flap 15 shall be selected, then landing flap 30 /40. Revision: 13 | Page | 40 All Weather Operations Guide ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ At 500ft radio the Captain calls "500 radio, flare armed", the F/O responds "passing XXX radio, flare armed". (Verify no steady A/P WARNING light at 500ft – No callout required). When approaching minimums, the captain will look out and call whatever, visual cues he/she sees i.e. "approach lights, runway etc." If no visual cues are available, he/she will remain silent until “Minimums”. If adequate visual cues exist at DH, the captain will call "continue" and take over the controls or call “go-around” and the F/O shall execute the go-around. If no callout is made by minimums the F/O shall execute the go-around. The decision to Continue or Go-Around must be made at “Minimums” The Go-Around must be INITIATED within 50ft and minus nothing of the DH/MDH. This applies to all approaches but is especially critical For CAT II / III due to the close proximity of the ground. If a decision to land is made the F/O must stay on instruments until reaching taxi speed. The captain will execute a go-around below DH if visual cues are lost, or a system malfunction occurs that prevents the aircraft from completing a successful landing. The F/O will call "no flare" or "no retard" if applicable. If an automatic callout is omitted the PM should make the expected callout. Captain may elect to leave landing lights off during CAT II / III operations only. Revision: 13 | Page | 41 All Weather Operations Guide Revision: 13 | Page | 42 All Weather Operations Guide Revision: 13 | Page | 43 All Weather Operations Guide GO-AROUNDS The Commander may elect to go-around from a low visibility approach at any time if there is any doubt as to whether the approach can be flown in a safe manner to a successful landing. Below 500ft AGL a Go-around is mandatory if: ▪ Any of the required airborne equipment becomes inoperative. ▪ Any of the required ground equipment becomes inoperative. ▪ An instrument crosscheck shows a significant discrepancy, or any Instrument comparator warnings are evident. ▪ A rate of descent greater than 1000 FPM occurs. ▪ The Visual Reference is inadequate. ▪ A touchdown within the TDZ cannot be accomplished; ▪ A Localizer or Glideslope deviation of more than one dot G/S or 1/3 dot Localizer occurs. The crew should, at no stage below 500ft AGL, hesitate or discuss whether a goaround is required or not. Normally, a go-around will be dual channel, however if the autopilot fails or an engine failure occurs a manual, single channel go around will be required. If a manual go-around is initiated below 400ft, crew should expect the aircraft to be trimmed nose up and therefore take care not to over rotate. Revision: 13 | Page | 44 All Weather Operations Guide 10. THE VISUAL CUES Touchdown zone lights should be provided in the touchdown zone of a precision approach runway Category II or III. The location and positioning should be as follows: 1) Touchdown zone lights should extend from the threshold for a longitudinal distance of 900m, expect that, on runways less than 1800m, the system should be shortened so that it does not extend beyond the midpoint of the runway. 2) The pattern should be formed by pairs of barrettes symmetrically located about the runway centreline. The lateral spacing between the innermost lights of a pair of barrettes should be equal to the lateral spacing selected for the touchdown zone marking. The longitudinal spacing between pairs of barrettes should be either 30m or 60m. Following an autoland, the airplane’s main gear should touchdown within the TDZ lighting system. Longitudinal touchdown will be between 60m from the threshold and before the end of the touchdown zone lighting (900m from threshold). CAUTION: TDZ Lighting (i.e The Carpet Lighting System) extends beyond the TDZ to allow pilots to judge the performance of the Autoland system. If you are performing a manual landing (CAT I or better conditions), the aircraft must touch down within the touchdown area. It is important to understand what the various lights indicated to the pilot, which lights he/she expects to see, and when. At those aerodromes where Category II / III approaches are conducted, Supplementary Approach Lighting consisting of centreline barrettes and two rows of red side barrettes, as shown at Figure 1.5 (C), are installed in order to provide the pilot with enhanced visual cues over the last 300m of the approach. NOTE: At certain aerodromes with displaced thresholds, the supplementary approach lighting is inset into the runway and in certain weather and ambient light conditions the centreline barrettes, at the higher intensity settings, can partially obscure the runway centreline lighting to pilots lining up for departure. Pilots experiencing problems of this nature should ask for the intensity of the supplementary lighting to be adjusted or extinguished. Revision: 13 | Page | 45 All Weather Operations Guide (A) (B) (C) Figure 1.5 Approach Lighting Revision: 13 | Page | 46 All Weather Operations Guide Approach lights are symbolized in recognizable form, and at the same scale as the airport chart. Typical examples: Revision: 13 | Page | 47 All Weather Operations Guide Figure 1.6: Examples of Approach Lighting Systems Figure 1.7: Papi Indications Revision: 13 | Page | 48 All Weather Operations Guide VISUAL ILLUSIONS Whereas the approach/runway lights afford some roll guidance, 300m RVR does not provide an adequate picture to enable the pilot to achieve an accurate visual perception of attitude. If the horizon is obscured, the crossbars are in dynamic motion. The distance to the farthest visible lights may appear to vary due to inconsistency and density of the fog. This situation can create the illusion that the aircraft is porpoising. To compound the above, a strong illusion of being too high on the slot is created when transitioning from instruments to visual in low visibility. This illusion is quite simply caused by the fact that the forward limit of visibility – to the pilot’s perception, the horizon – is much lower than usual (in fact it is half-way down the windscreen). Side effects of the above are: • A sudden decrease of visibility will cause the illusion of a pitch-up. • A sudden increase of visibility will cause the illusion of a pitch-down. Maintaining a rapid scan of instruments and visual cues throughout the visual sector can guard against these illusions and false perceptions. Figure 1.8 Pilot Eye Height at 10m and 5m Revision: 13 | Page | 49 All Weather Operations Guide RAPID EXIT TAXIWAY INDICATOR LIGHTS: Rapid exit taxiway indicator lights (RETILs) provide pilots with distance to go information to the nearest rapid exit taxiway on the runway, to enhance situational awareness in low visibility conditions and enable pilots to apply braking action for more efficient roll-out and runway exit speeds. RETILs consist of six yellow lights adjacent to the runway centre line and configured in a three/two/one pattern spaced 100 m apart; the single light is 100 m from the start of the turn for the rapid exit taxiway, see Figure 1.9. Figure 1.9 RETILs 11. AERODROME FACILITIES When Low Visibility Operations are planned for an aerodrome, all the facilities of the aerodrome must be considered and assessed for their suitability for such operations. Special procedures, and, in some instances, additional equipment, may be required to ensure that these operations can be conducted safely. Revision: 13 | Page | 50 All Weather Operations Guide This section of the guidance is intended to provide baseline requirements for the development of detailed procedures. The actual facilities and procedures required at any aerodrome depend on the type of operations to be conducted at that aerodrome. The specific types of operations that require LVP are: A. Departure operations in RVR less than a value of 550m. B. CAT II and CAT III approach and landing operations. The extent and complexity of the procedures depend on the operations being conducted, but the objective of the LVP is to protect the physical area around the runway and to protect any guidance signals that may be used during these operations. The conduct of Low Visibility Operations depends on the existence of suitable runway protection measures, surface movement guidance and control, emergency procedures, apron management, MET service and equipment. Although it is recognized that the implementation of these requirements is basically the responsibility of the appropriate State and aerodrome authority, the aircraft operator should ensure as far as possible that suitable measures have been taken. PHYSICAL CHARACTERISTICS. The physical characteristics of the runways and taxiways, as well as the requirements for obstacle clearance, the protection of the defined areas surrounding a runway, and the characteristics of pre-threshold terrain need to be carefully considered to ensure safe operations in Low Visibility Conditions. OBSTACLE FREE ZONE (OFZ) (Annex-14) The airspace above the inner approach surface, inner transitional surfaces, and balked landing surface and that portion of the strip bounded by these surfaces, which is not penetrated by any fixed obstacle other than a low-mass and frangible mounted one required for air navigation purposes. AIRPORT VISUAL AIDS Runway lighting and marking must be in compliance with ICAO Annex 14 Standards and Recommended Practices & the EASA Regulation (EU) No 139/2014. Runways certified for Cat II and Cat III ILS Operations must be equipped accordingly, including threshold lighting, runway markings, runway edge lighting, runway-end lighting and markings, runway centre line lighting and markings and touch down zone lighting and markings. Secondary power supply (switch over time of 1 second) for the Visual Aids will be provided in accordance with the requirements of ICAO Annex 14. Any failure of the secondary power supply equipment will result in a down- grading of ILS Operations and reference should be made to the tables presented above in this manual or the OPA manual part A which is the official document. Revision: 13 | Page | 51 All Weather Operations Guide NON-VISUAL AIDS Low Visibility Operations require a means of guidance for the aircraft on the approach to the runway and for some take-off operations. The demanding requirements of Low Visibility Operations means that it is particularly important to ensure that the guidance signals are of the highest quality. Where ground-based antennas are used to provide these signals, then this quality is assured by establishing critical and sensitive areas. These include all approach radio aids such as ILS/MLS and VOR/DME, also locator beacons and fan markers both of which are now being gradually withdrawn. EQUIPMENT ILS ground equipment serving instrument runways must have no-break power supplied by dual systems located and operated according to ICAO Annex 10, Volume 1 Standards and Recommended Practices. Automatic monitor systems according to the requirements of Annex 10, Volume 1, Part 1, are to be provided for all ILS ground systems components. Localizers (LLZ) certified for CAT II and/or CAT III operations are to be additionally monitored by a far-field monitor. Pilots will be informed without delay of any deficiency. ILS CRITICAL AREA (Annex 10) An area of defined dimensions about the localizer and glide path antennas where vehicles, including aircraft, are excluded during all ILS operations. The critical area is protected, because the presence of vehicles and/or aircraft inside its boundaries will cause unacceptable disturbance to the ILS signal-in-space. ILS SENSITIVE AREAS (Annex 10). ILS sensitive areas are those extending beyond the critical area where the parking and/or movement of vehicles, including aircraft, are controlled to prevent the possibility of unacceptable interference to the ILS signal during ILS operations. The sensitive area is protected to provide protection against interference caused by large moving objects outside the critical area but still normally within the airfield boundary. SECONDARY POWER SUPPLY All radio navigation aids, essential communication equipment and the RVR assessment system must be supplied with ‘no-break’ power. AERONAUTICAL INFORMATION SERVICES When any part of the system supporting Low-Visibility Operations is unserviceable or downgraded, a NOTAM shall be issued, provided the failure time complies with the NOTAM issuance requirements, giving a full description of what is unserviceable or downgraded. NOTAM’s shall also include any additional measures or restrictions that have been taken in the LVP as a result of the downgrading. Revision: 13 | Page | 52 All Weather Operations Guide ATIS broadcasts are provided at aerodromes where there is a requirement to reduce the load on RTF communication channels and therefore reduce the workload on both controllers and pilots. This is particularly beneficial in LVP where additional information about the status of LVP and the aerodrome facilities should be provided. Pilots can receive the information required before they are in RTF contact with approach control units or before start-up. The information provided by ATIS broadcasts in LVP can assist pilots in planning for the approach and, should the need arise, any diversions in a timely manner. TERRAIN PROFILE The terrain profile under the approach path should be free of excessive up or down slopes and discontinuities, since the radio altimeters provide input signals to the autopilots for gain programming during a coupled approach from 1500ft and for pitch control during flare from 50ft. Before a runway is approved for CAT II or CAT III operations, the terrain profile is investigated for its suitability in accordance with established criteria. The radio altitude at DH published on CAT II / III approach charts takes account of any differences between threshold elevation and the level of terrain below the approach on the extended centre line. The published RA minima is designed to provide minimum DH above the threshold as per regulations e.g. minimum DH over the threshold for CAT II approach is 100ft. For example: in Dublin RWY 10R/28L the CAT II minima differs from 100ft. The minima set on PFD is the published minima 94ft, or 105ft respectively, which provides 100ft DH above the threshold. METEOROLOGICAL SERVICE The status of LVP shall be passed to pilots by means of the ATIS broadcast where available, except for short notice changes, which shall be passed by ATC. Revision: 13 | Page | 53 All Weather Operations Guide CAT II/III APPROVAL PROCESS Figure 5.8 reporting Two of transmissometer Accurate and timely oftypes meteorological conditions according to ICAO Annex 3 must be provided at the aerodrome concerned. CAT II/III APPROVAL PROCESS Runway Visual Range (RVR) is normally assessed by electronic ‘Transmissometers’ whose position must be abeam the touchdown zone and stop-end of instrument runways. Figure 5.8 Two types of transmissometer TWO TYPES OF TRANSMISSOMETERS Transmitter and receiver Transmitter and receiver The fact that the RVR is at or above limits in no way obliges a pilot to attempt a landing in these conditions - it merely allows the Pilot to make an approach and judge the visual conditions. The decision to land is- 149 made by the pilot, not by the RVR. The RVR value is, therefore, best regarded only as the means of determining whether or not an approach ban exists. The accurate, regular and frequent RVR reporting required for - 149 -a good indication of conditions on the this purpose will at the same time provide runway in the touchdown zone for landing aircraft. Before the introduction of instrumented RVR systems, the method of assessing RVR was based on visual observations using lights or special markers, performed by a human observer. This system is retained as a standby system for use in case of a failure of the instrumented system. Those responsible for carrying out the human observations should report RVR to the appropriate local ATS unit(s) whenever there is Revision: 13 | Page | 54 All Weather Operations Guide a change in the value to be reported in accordance with the reporting scale in use. According to Annex 3, Appendix 3, arrangements for the transmission of the reports to ATS units concerned should be such that transmission is normally completed within fifteen seconds after the termination of the observation. Runway Visual Range is a measure of the opacity of the horizontal sample of the atmosphere at a low height it can take no account of vertical density changes. With regard to fog structure, data gathered in the United Kingdom over a twenty-year period has shown that in deep stable fog there is a 90% probability that the slant visual range from eye heights higher than 15ft above the ground will be less than the horizontal visibility at ground level, i.e. RVR. There are at present no data available to show what the relationship is between the Slant Visual Range and RVR in other low visibility conditions such as blowing snow, dust or heavy rain, but there is some evidence in pilot reports that the lack of contrast between visual aids and the background in such conditions can produce a relationship similar to that observed in fog. 12. ENVIRONMENTAL FACTORS THE CHARACTERISTICS OF FOG Fog will only form and persist if particular values of temperature, humidity, and wind all exist simultaneously. Small changes in any one of these parameters will result in variations in the extent, density, and depth of the fog and it is this sensitivity that is responsible for its extreme and continuous variability. Even under stable conditions, a large variation in the vertical plane of the concentration and size of water droplets is known to occur, with a tendency for the greater concentration to be at the higher levels. For this reason, it is normal for the visual range within the fog to increase closer to the ground. Although a shallow fog is the usual cause of decreasing visual segment under stable fog conditions, a similar effect can be experienced in a dense fog where the density is greatest near the surface. In this case, as height decreases, the| 55 Revision: 13 | Page pilot is looking through fog steadily increasing density and a reduction of visual segment may be experienced at quite a low height. All Weather Operations Guide Although a shallow fog is the usual cause of decreasing visual segment under stable fog conditions, a similar effect can be experienced in a dense fog where the density is greatest near the surface. In this case, as height decreases, the pilot is looking through fog steadily increasing density and a reduction of visual segment may be experienced at quite a low height. Night and day naturally affect visual cues. At night the lights stand out in contrast and afford better visual information than during daytime. During day operations, the lights will be less discernible, and the visual segment will appear shorter. Despite this, most pilots are more comfortable in daytime, due to better cockpit visibility and cues available from runway contrast and markings LOW LEVEL WINDSHEAR AND TURBULENCE Weather limits require that CAT II / III approaches should not be conducted whenever windshear or Turbulence more than light to moderate is reported. It is important to understand the effects of these conditions. Windshear is a sustained change in the wind velocity along the aircraft flight path, which occurs significantly faster than the aircraft can accelerate or decelerate. Windshear can occur at any level, but it is low-level windshear, occurring from the surface to a height of approximately 1500 feet, which can cause problems of sufficient magnitude to affect the control of aircraft in departure or final approach phases of flight. CONDITIONS CONDUCIVE TO WINDSHEAR a) The presence of frontal/squall/thunderstorm activity in the vicinity of the aerodrome. b) The presence of low-level inversions where the surface wind will be significantly different from that at only a few hundred feet above the ground. c) Local terrain or buildings considered in relation to wind speed and direction; such large obstructions can cause windshear as well as the more usual turbulence and gusts. A combination of factors can make the analysis of windshear very complex, but three simple examples of the hazards of low-level windshear are shown below: a) As the aircraft flies from A to B and traverses the windshear line, the inertia of the aircraft maintains the ground speed of 170 kts and the change of wind vector causes a sudden fall in airspeed. This can result in reduced lift until the inertia of the aircraft has been overcome and the original airspeed regained. Clearly this may be hazardous at critical climb-out speeds; Revision: 13 | Page | 56 All Weather Operations Guide b) If an aircraft on final approach passes through a windshear line which causes a sudden loss of airspeed and a consequent increase in the rate of descent, a rapid application of power will be required if the aircraft is not to sink to a dangerously low height; c) If the aircraft passes through a windshear line from a tailwind to a headwind component the inertia of the aircraft results initially in an increased airspeed and a deviation above the glidepath. The pilot’s instinctive power reduction can result in the aircraft being short of power with a high rate of descent as the glidepath is approached and the effect of the inertia is lost. A rapid increase of power is now required if the aircraft is not to sink below the glidepath at a dangerously low altitude. Revision: 13 | Page | 57 All Weather Operations Guide THE RELATIONSHIP BETWEEN WINDSHEAR AND TURBULENCE Turbulence is the direct result of windshear. The stronger the shear the greater the tendency for the laminar flow of the air to break down into eddies resulting in turbulence. However, not all shear zones are turbulent, so the absence of turbulence does not infer that there is no shear. THE EFFECTS OF PRECIPITATION AND ICING Weather limits require that CAT II / III approaches should not be conducted whenever precipitation greater than moderate is reported. It is important however to understand the effects of these conditions. FLIGHT IN MODERATE TO HEAVY RAIN, HAIL, OR SLEET The airplane is designed to operate satisfactorily when the maximum rates of precipitation expected in service are encountered. However, flight into moderate to heavy rain, hail, or sleet could adversely affect engine operations and should be avoided whenever possible. If moderate to heavy rain, hail, or sleet is encountered, reducing airspeed can reduce overall precipitation intake. Also, maintaining an increased minimum thrust setting can improve engine tolerance to precipitation intake, provide additional stall margin, and reduce the possibility of engine instability or thrust loss Revision: 13 | Page | 58 All Weather Operations Guide Supplementary Procedure for Flight in Moderate to Heavy Rain, Hail, or Sleet: The Supplementary Procedure recommends that the crew should consider starting the APU, if available, because it provides quick access to backup electrical and pneumatic sources. VISUAL ILLUSIONS FROM PRECIPITATION In light rain or moderate rain, the runway may appear fuzzy because of rain halo effect, increasing the risk of not perceiving a vertical deviation or lateral deviation during the visual segment. The visual segment is defined as the segment flown after full transition from instruments to visual references. Heavy rain affects depth perception and distance perception: • • • Rain on windshields creates a refraction and the perception of being too high, thus inducing a nose down correction that places the aircraft below the desired flight path; In daylight conditions, rain diminishes the apparent intensity of the approach lighting system (ALS) resulting in the runway appearing to be farther away. As a result of this illusion, the flight crew tends to shallow the flight path resulting in a long landing; In night-time conditions, rain increases the apparent brilliance of the ALS, making the runway appears to be closer, inducing a pitch down input and the risk of landing short of the runway threshold. Revision: 13 | Page | 59 All Weather Operations Guide LANDING Unfortunately, flight crews do not always receive up to date information on whether a runway is contaminated or not. This may arise from three causes: • Delays in the making of inspections and measurements by the airport operator; • Delays in advice to ATC of runway surface status; • The current absence of methods for the tactical measurement of braking action or other runway friction indication on runways, which are or may be contaminated with water. If contamination by liquid water is suspected, a review with ATC of the incidence of recent precipitation is advisable to help decide whether to delay an approach or continue as originally intended. Alternatively, another runway may be available. Any pilot reports or observations made directly by ATC and therefore qualified by the prefix ‘unofficial’ may provide useful information. However, these need to be used carefully if conditions are likely to be changing rapidly, due to varying rates and intensities of precipitation. Where contaminated runway conditions appear likely to be relatively slow changing, the full detail available on the ATIS, from the METAR runway state group, or a SNOWTAM should be carefully assessed before an approach begins. The airmanship conclusion, which may be drawn from the above, is that even though it is believed that the runway is not contaminated, it may be found on touch down that the surface is contaminated, at least in part, and especially by liquid water. Therefore, the issues relevant to an intended contaminated runway landing may have to be considered when preparing to land in bad weather in order to reduce the risk of runway excursions due to loss of control on low friction surfaces. Autobrakes should remain engaged until a safe stop is assured and adequate visibility exists to control the airplane using visual reference AUTOLAND WITH CROSSWIND CONDITIONS During an autoland with crosswind conditions, fail passive airplanes will touchdown in a crab. After touchdown, the rudder must be applied to maintain runway centreline. The autopilot must be disengaged immediately after touchdown. The control wheel should be turned into the wind as the autopilot is disengaged. SLIPPERY RUNWAY LANDING PERFORMANCE When landing on slippery runways contaminated with ice, snow, slush or standing water, the reported braking action must be considered. Advisory information for reported braking actions of good, medium and poor is contained in the OPT and PI chapter of the QRH. The performance level associated with good is representative of Revision: 13 | Page | 60 All Weather Operations Guide a wet runway. The performance level associated with poor is representative of a wet ice-covered runway. Also provided in the QRH are stopping distances for the various auto brake settings and for non-normal configurations. Pilots should use extreme caution to ensure adequate runway length is available when poor braking action is reported. Pilots should keep in mind slippery/contaminated runway advisory information is based on the assumption of uniform conditions over the entire runway. The data cannot cover all possible slippery/contaminated runway combinations and does not consider factors such as rubber deposits or heavily painted surfaces near the end of most runways. One of the commonly used runway descriptors is coefficient of friction. Ground friction measuring vehicles typically measure this coefficient of friction. Much work has been done in the aviation industry to correlate the friction reading from these ground friction-measuring vehicles to airplane performance. Use of ground friction vehicles raises the following concerns: • The measured coefficient of friction depends on the type of ground friction measuring vehicle used. There is not a method, accepted worldwide, for correlating the friction measurements from the different friction measuring vehicles to each other, or to the airplane's braking capability. • Most testing to date, which compares ground friction vehicle performance to airplane performance, has been done at relatively low speeds (100 knots or less). The critical part of the airplane's deceleration characteristics is typically at higher speeds (120 to 150 knots). • Ground friction vehicles often provide unreliable readings when measurements are taken with standing water, slush or snow on the runway. Ground friction vehicles might not hydroplane (aquaplane) when taking a measurement while the airplane may hydroplane (aquaplane). In this case, the ground friction vehicles would provide an optimistic reading of the runway's friction capability. The other possibility is the ground friction vehicles might hydroplane (aquaplane) when the airplane would not, this would provide an overly pessimistic reading of the runway's friction capability. Accordingly, friction readings from the ground friction vehicles may not be representative of the airplane's capability in hydroplaning conditions. • Ground friction vehicles measure the friction of the runway at a specific time and location. The actual runway coefficient of friction may change with changing atmospheric conditions such as temperature variations, precipitation etc. Also, the runway condition changes as more operations are performed. The friction readings from ground friction measuring vehicles do supply an additional piece of information for the pilot to evaluate when considering runway conditions for Revision: 13 | Page | 61 All Weather Operations Guide landing. Crews should evaluate these readings in conjunction with the PIREPS (pilot reports) and the physical description of the runway (snow, slush, ice, standing water etc.) when planning the landing. Special care should be taken in evaluating all the information available when braking action is reported as POOR or if slush/standing water is present on the runway. ICE ACCRETION Wing and engine anti-ice systems are to be used in accordance with the Boeing 737700/800/8200 standard operating procedures bearing in mind they may be required at a late stage during a CAT II / III approach. One of simplest assumptions made about clouds is that cloud droplets are in a liquid form at temperatures warmer than 0°C and that they freeze into ice crystals within a few degrees below zero. In reality, 0°C marks the temperature below which water droplets become supercooled and are capable of freezing. While some of the droplets actually do freeze spontaneously just below 0°C, others persist in the liquid state at much lower temperatures. Aircraft icing occurs when supercooled water droplets strike an aircraft whose temperature is colder than 0°C. The effects icing can have on an aircraft can be quite serious and include: • • • Disruption of the smooth laminar flow over the wings causing a decrease in lift and an increase in the stall speed. This effect is particularly dangerous. An “iced” aircraft is effectively an “experimental” aircraft with an unknown stall speed. Restriction of visibility as the Windshield glazes over. Increase in angle of attack further reducing visibility. COMPETENCE OF THE FLIGHT CREW FOR THE INTENDED OPERATIONS EXPERIENCE IN TYPE OR CLASS, OR AS PILOT-IN-COMMAND/COMMANDER SPA.LVO.120, AMC1 SPA.LVO.120(a) Prior to conducting Low Visibility Operations, The Ryanair Group, through its approved ATO, ensures that each flight crew member: • • • Complies with the training and checking requirements prescribed in the operations manual part D, including Flight Simulation Training Device (FSTD) training in operating to the limiting values of RVR/VIS (visibility) and DH specific to the operation and the aircraft type; Is qualified in accordance with the standards prescribed in the operations manual. Training and checking is conducted in accordance with a detailed syllabus. Revision: 13 | Page | 62 All Weather Operations Guide Initial training for LVO procedures includes ground school training, simulator training as laid out on form LVI-737 and line flying under supervision that includes requirements for auto-lands to be conducted. During recurrent LVO training and checking, crews will conduct at least two LVO approaches and a LVTO. Crews should complete the LVO Recurrency Form that can be found on e-learning and log evidence of 1 CAT II / III approach and 1 Monitored Approach in the previous 6 months. The Flight Crew qualification is specific to the operation (take-off, CAT II / III) and the aircraft type. The Ryanair approvals for Flight Crew operating on the B737700/800/8200 are as follows: • • • Take-off: 125 m RVR Landing CAT II 100 ft RA/300 m RVR Landing CAT III 50 ft RA/175m* RVR, *where applicable COMMANDER LVO QUALIFICATION 5.1.3.1 Commander LVO Qualification A commander is authorized to conduct a take-off in minimum RVR (125m) when he has successfully completed the LVO training prescribed in the RST (Recurrent Simulator Training) 5.1.3.1.1 New Commanders LVO Qualification A Commander is only authorized to conduct CAT II / III approaches after the following prerequisites have been accomplished: 100m must be added to the applicable CAT II or CAT III RVR minima until a total of 100 hours or 40 sectors (whichever occurs first), as Commander on the type have been accumulated in line flying, including line training as part of the Command upgrade course. Revision: 13 | Page | 63 All Weather Operations Guide FIRST OFFICER LVO QUALIFICATION 5.1.3.2 First Officer LVO Qualification Due to the high workload involved with LVP’s during ground operations, the F/O shall act as PM during take-off operations in visibility conditions of less than 550m RVR. For approach and landing the F/O is designated as PF until minima and will remain PF unless the commander decides to take control and land. i.e. a go-around shall be flown by the F/O. Company policy is the Commander will announce “CONTINUE” if he intends to take control. Revision: 13 | Page | 64 All Weather Operations Guide APPENDIX – MONITORED APPROACHES A Monitored Approach (MA) is applicable when weather conditions are marginal. They can be performed on a Non-ILS approach and a CAT I ILS approach. Monitored Approaches allow the Captain (LHS) to spend more time looking outside while the F/O (RHS) is flying the aircraft on instruments using the autopilot (if available). When the captain calls continue, he or she takes control. A go-around shall be executed by the F/O when instructed, or if there is no instruction from the Captain at minimums. Weather conditions in which a monitored approach is mandatory are described in the Monitored Approach Checklist in the QRH. These are limits when a Monitored Approach MUST be carried out. Nothing prevents a crew to conduct a Monitored Approach in better weather conditions. A double briefing is required for all Monitored Approaches that are non-ILS/GLS Approaches. Threat and Error Management should be used to identify threats, such as downgraded aircraft equipment, absence of approach and/or centre line lights, heavy rain, crosswind, darkness, limited visual cues, … For example, when landing on a Runway without Centerline lights in marginal weather, this threat might be mitigated by completing a monitored approach, in order to avoid aligning the aircraft with the Runway edge lights and to ultimately avoid a Runway Excursion. Remember: ANTICIPATE - RECOGNISE – RECOVER – SAFE FLIGHT • A Monitored Approach is NOT applicable to Circle-to-Land approaches. • V/S must not exceed 1,000 fpm continuously unless required by the published procedure and briefed prior to the approach. Revision: 13 | Page | 65 All Weather Operations Guide Example of a Monitored Approach: When landing on a Runway without Centerline lights in marginal weather, the threat of the reduced runway lighting may be mitigated by completing a monitored approach, in order to avoid aligning the aircraft with the Runway edge lights and to ultimately avoid a Runway Excursion. The following pictures at respectively 200ft & 100ft AGL show the visual references without centerline lights and weather conditions OVC003 – RVR1000m. Revision: 13 | Page | 66
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )