SESSIONAL QUESTIONS
SUBJECT: BASIC ELECTRICAL ENGINEERING (BE-202)
UNIT-1
Q. 1 Draw and explain single line diagram in generation, transmission and distribution of electrical energy.
Q. 2 For the given circuit in Fig.1, find the Norton equivalent between points A and B.
Q. 3 Solve the network shown in Fig.2 and find the current in each branch.
Q. 4 Find the resistance between AB of the circuit shown in Fig.3 using star–delta transformation.
Fig.1
Fig.2
Fig.3
Q.5 Explain Mesh current method for solving networks. How are the Mesh current method written?
Q.6 State and explain Millman’s theorem and Reciprocity theorem.
UNIT-2
Q.7 Explain the term resonance. Derive expression for series resonance and quality factor in single phase AC
series circuits?
Q.8 A 20 Ω resistor is connected is series with an inductor and a capacitor across a variable frequency 25 V
supply. When the frequency is 400 Hz, the current is at its maximum value of 0.5 A and the potential
difference across the capacitor is 150 V. Calculate the resistance and inductance of the inductor.
Q 9. A resistance of 24 Ω, a capacitor of 150 µF and an inductor of 0.16 H are connected in series with each
other. A supply of 240 V, 50 Hz is supplied to the ends. Calculate (a) the current in the circuit (b) the
potential drop across each element (c) the frequency to which the supply would need to be changed so that
the current would be at unity power factor and find the current at this frequency.
Q.10 What do you understand by three phase system. For three-phase a.c. system, derive the relation between
phase and line voltage and currents in both star and delta connections.
Q.11 Explain two wattmeter method for the power measurement in three phase AC circuits with Different
conditions.
Q.12 A balanced delta connected load of (12+j9) Ω/phase is connected to three phase 400 V supply. Find (i)
Line current (ii) Power Factor (iii) Power drawn (iv) Reactive volt- amperes (v) Total volt-amperes.
UNIT-3
Q.13 Describe BH curve in detail? What is meant by hysteresis loss, on what factors do they depend and how
they Minimized?
Q.14 Describe statically & dynamically induced emf. Also explain its types
Q.15 An iron ring has its mean length of flux path as 60 cm and its cross sectional areas as 15 cm2. Its relative
permeability is 500. Find the current required to be passes through to a coil of 300 turns wound uniformly
around it to produce a flux density of 1.2 tesla. What would be the flux density with the same current if the
iron ring is replaced by air core?
Q.16 A length of an air solenoid is 1.7 m and area of cross-section is 12 cm2. The number of turns of coil is
1000. Calculate: (i) The self inductance (ii) The energy stored in magnetic when a current of 10 A flows
through the coil.
Q.17 Derive an expression for the emf induced in a transformer winding. Show that the emf induced per turn in
primary is equal to the emf per turn in secondary winding.
Q.18 Draw and explain phasor diagram for single phase transformer under no load and legging load condition.
Q.19 Draw the equivalent circuit of a transformer explaining each step involved.
Q.20 A 50 kVA single phase transformer has a full load primary current of 250 A and total resistance referred
To primary is 0.006Ω. If the iron loss amount to 200 W, find the efficiency on full load and half load at
(i) unity power factor and (ii) 0.8 power factor
Q.21 Consider a 20 kVA, 2200/220V, 50 Hz transformer. The OC/SC test results are as follows:
O.C. test: 220 V, 4.2 A, 148 W on L.V. side
S.C. test: 86 V, 10.5 A, 360 W on H.V. side
(i) Determine the regulation at 0.8 p.f. lagging at full load. (ii) What is the p.f. on short circuit?
UNIT-IV
Q.22 How is back emf produced in a DC motor? Further, derive an expression for this emf.
Q.23 Name and explain various methods of excitation of DC machines.
Q.24 Explain the speed-current, torque-current, and speed-torque characteristics of a DC shunt and Series
motor.
Q.25 How the speed of a DC motor can be controlled? Describe the basic principles of the various Methods for
controlling of speed of a DC motor?
Q.26 Explain Constructional details of synchronous machine. Derive the EMF equation also.
Q.27 Explain Constructional details of three phase Induction motor.
Q.28 A 6-pole machine has an armature with 90 slots and 8 conductors per slot, the flux per pole is 0.05 Wb
and rms at 1,000 rpm. Determine induced emf if winding is (i) lap connected and (ii) wave connected.
Q.29 An 8-pole DC generator has 600 armature conductors and a useful flux of 0.06 Wb. What will be the emf
generated if it is lap wound and runs at 1,000 rpm? What must be the speed at which it is to be driven to
induce the same voltage if it is wave wound?
Q.23 A 6-pole lap wound 230 V shunt motor has 400 armature conductors. It takes 41A on full load. The flux
per pole is 0.05 Weber. The armature and field resistances are 0.1 ohm and 230 ohms respectively.Contact
drop per brush = 1V. Determine speed of motor at full load.